Search NASA⌕ Search

SEARCH · Search NASA

Results for “Modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Tribological Behavior of Pulsed Electrodeposited Ni-W/SiC Nanocomposites

Ni-14 at.% W/SiC nanocomposite coatings containing 0-6 vol.% of submicron size (0.35 μm) SiC particles were obtained using pulsed electrodeposition technique on mild steel substrate. The coatings were subsequently characterized for uniformity of SiC distribution, grain size and mechanical properties (hardness and elastic modulus) using SEM, XRD and nanoindentation techniques, respectively. It was observed that the SiC particulates were uniformly distributed within the coating. The coating matrix (Ni-W) also exhibited nanograin size. Tribological behavior of Ni-14 W/SiC nanocomposite was analyzed under dry sliding wear test conditions using pin on disk method. The interrelationship between SiC content, interparticle spacing, mechanical properties and wear behavior was analyzed. The results suggest that whereas hardness and modulus of nanocomposite coatings varied with SiC content as per Rule of Mixtures, wear mechanism can be best explained on the basis of Inverse Rule of Mixtures.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Microstructure, Phase Transformation, Mechanical Behavior, Bio-corrosion and Antibacterial Properties of Ti-Nb-xSn (x = 0, 0.25, 0.5 and 1.5) SMAs

Porous Ti-Nb-xSn shape memory alloys (SMAs) are fabricated by microwave sintering technology. The microstructures exhibit needle-like morphologies, β{sub (N)} (normal straight and crossed needles along with needle-like morphology that resembles spaghetti or irregular lines with α-phases in between) as well as plate-like morphologies [normal straight plate-like morphology, α′′ and dendritic plate-like morphology, β{sub (D)}]. Increases in Sn addition significantly induce an increase in the density of the α-phase. XRD patterns exhibited three phases, namely the β-main phase with smaller intensities of α′′ and α. Further, the addition of 0.25% Sn led to more effective improvement in the intensity of the α′′-phase compared with 0.5% and 1.5% Sn addition. Additions of Sn also enhanced the fracture strength and its corresponding strain along with the shape memory effect (SME), where the best enhancement was achieved at 0.25% Sn. The corrosion rate (Ri) was reduced by rising Sn content, while both corrosion resistance and antibacterial zones were increased. The lower elastic modulus, as well as the robust mechanical properties and bioactivity, made these SMAs rather suitable for biomedical application purposes, where the low elastic modulus had value in terms of avoiding the problem of “stress shielding.”.

36 MATERIALS SCIENCE↗

Effect of Prolonged Ultraviolet Radiation Exposure on the Blast Response of Fiber Reinforced Composite Plates

An experimental study with corresponding numerical simulations was conducted to evaluate the blast response of composite plates after prolonged exposure to ultraviolet radiation. Two composite materials were used in this study, namely carbon fiber/epoxy and glass fiber/vinyl ester. The composite materials consisted of four unidirectional fiber plies oriented in a [± 45°]s layup. The plates were placed in a QUV Accelerated Weathering Tester for 500 h of exposure on each face, totaling 1000 h of ultraviolet radiation exposure, equivalent to 2.5 MJ/m{sup 2} of energy. The QUV Accelerated Weathering Tester was equipped with eight UVA-340 lamps to provide real service life exposure conditions. Material characterization experiments were performed on virgin specimens, as well as specimens exposed to ultraviolet radiation for 1000 h to determine its effect on the mechanical properties of the composites. Blast experiments were conducted on the composite plates to investigate the dynamic response before and after exposure to ultraviolet radiation. The plates were clamped on all edges and subjected to an air blast using a shock tube apparatus. Three-dimensional digital image correlation was coupled with high-speed photography to obtain full-field displacements of the specimens during blast loading. Furthermore, three piezoelectric pressure transducers were mounted on the shock tube apparatus and utilized to measure the pressure history of the shock wave loading. The quasi-static material characterization showed that the tensile modulus E{sub 1} had minimal change after exposure to ultraviolet radiation for 1000 h. However, matrix-dominated properties such as the in-plane shear modulus G{sub 12} increased after exposure to ultraviolet light for both the carbon and glass fiber composites, which resulted in lower out-of-plane displacements during blast loading. For the carbon fiber plates, the forced vibration frequency induced by the transverse blast load was higher in plates exposed to ultraviolet radiation when compared to virgin specimens. However, for the glass fiber plates exposed to ultraviolet radiation, the forced vibration frequency decreased when compared to virgin specimens. Finally, the finite element simulations were in good agreement with the experimental results. The simulations revealed that the glass fiber plates exposed to ultraviolet radiation had higher failure strains at the boundary than virgin specimens, despite having higher stiffness. A parametric study in which higher loading was simulated also showed that the glass fiber plates experienced more damage after 1000 h of ultraviolet radiation exposure.

36 MATERIALS SCIENCE↗

The Effects of Sc Addition on the Microstructure and Mechanical Properties of Be-Al Alloy Fabricated by Induction Melting

This study investigated the alloying effects of 0.4 wt.% Sc on the microstructure, mechanical properties, and fracture behavior of a cast Be-Al alloy prepared by vacuum induction melting. The micromechanics of Sc-containing secondary-phase particles (SPs) were characterized by nanoindentation, and the fracture behavior of the alloy was investigated via tensile fractography and optical metallography. The addition of 0.4 wt.% Sc significantly modified the alloy microstructure by decreasing the secondary dendritic arm spacing (SDAS), weakening the dendritic structure of Be, and producing an equiaxed/cellular alloy microstructure with refined Be grains. Sc alloying increased the Vickers hardness by 36%, elastic modulus by 28%, yield strength by 35%, ultimate strength by 52%, but decreased the elongation from 3.6 to 2.9%. Sc-containing SPs had a higher elastic modulus, yield strength, microhardness, and a lower plasticity index than the Be and Al matrices, resulting in interface separation during the fracture process. SPs located at the Be/Al interfaces did not act as microcrack sources for the matrices, whereas highly faceted SPs within the Be grains induced microcrack formation and decreased the elongation. The failure mode of the cast Be-Al-0.4Sc alloy still involved the brittle cleavage failure of Be regions and ductile dimple failure of Al regions, which was not the case with the cast Be-Al alloy.

36 MATERIALS SCIENCE↗

Dry Sliding Wear Resistance of Cobalt Boride Coatings Formed on ASTM F1537 Alloy

New results about the wear resistance of CoB-Co{sub 2}B coatings under dry sliding conditions were estimated in this work. The cobalt boride coatings were developed at the surface of the ASTM F1537 alloy by means of the powder-pack boriding process using two experimental conditions: 1223 K with 6 h of exposure and 1273 K with 10 h of exposure. Before the sliding wear tests, Vickers depth-sensing microindentation tests were conducted on the cross section of the cobalt boride coatings to estimate the distribution of hardness, Young’s modulus, and residual stresses. Otherwise, the sliding wear tests were performed on both boriding conditions and on the untreated material, using a ball-on-flat configuration comprised of an alumina ball as a counterpart with applied loads between 5 and 20 N. The wear rates of the borided ASTM F1537 alloy were ranged between 4.02 and 8.91 × 10{sup −6} mm{sup 3} N{sup −1} m{sup −1} compared with the values of the untreated material (13.90 and 15.78 × 10{sup −6} mm{sup 3} N{sup −1} m{sup −1}) for the overall set of experimental conditions; nevertheless, the influence of boriding conditions (1273 K with 10 h of exposure) tended to increase the CoB coating thickness, developing a more brittle layer that decreased the sliding wear resistance at the surface of the borided ASTM F1537 alloy. Finally, the presence of failure mechanisms on the surface of the wear tracks was analyzed for both borided ASTM F1537 alloy and untreated material.

36 MATERIALS SCIENCE↗

Investigation into the Wear and Dent Resistance of Ni/Ti Nanolaminates and Superelastic NiTi Coating

Metallic wear-resistant coatings, such as chromium based, are desired to prevent premature failure of working parts and are widely used in the oil and gas and aerospace industries. These coatings are extremely hard; however, researchers have found that an optimal coating will also be resilient. Bulk NiTi possesses a superelasticity effect that can provide wear resistance to parts that will experience impact, wear, and erosion daily. Yet, NiTi as a surface coating has not been fully exploited in industrial applications. Bulk NiTi production presents significant challenges, such as poor formability and machinability. This study attempts to fabricate NiTi through a heat treatment process of sputter-deposited alternating nanosized Ni and Ti layers. After annealing, the nanolaminate coatings contained the austenitic NiTi phase. The elastic modulus to hardness ratio and wear resistance showed that the nanolaminate annealed at 650 °C is comparable to the sputtered superelastic NiTi coating. The annealed nanolaminate coating is found to exhibit higher hardness than the monolayered NiTi, as well as, comparable elastic modulus to hardness values and dent resistance. The findings in this study reveal the superiority of 650 °C annealed nanolaminate NiTi coating over the monolayer NiTi.

36 MATERIALS SCIENCE↗

Effect of Solution Treatment on the Microstructure, Micromechanical Properties, and Kinetic Parameters of the β → α Phase Transformation during Continuous Cooling of Ti-6Al-4V Titanium Alloy

The aim of this study is to examine the effect of solution treatment temperature (STT) on the microstructure, the micromechanical properties, and the kinetic parameters of the β → α phase transformation during continuous cooling of the dual phase titanium alloy Ti-6Al-4V. Increasing the STT from 1050 to 1200 °C delays the formation of the α phase during cooling and increases the value of its activation energy. The microstructural analysis reveals the emergence of α{sub W} platelets from protuberances on the α{sub GB}/α{sub W} interface. The investigation of the morphology of the α{sub W} platelets reveals the presence of ledges on their longest side showing a sharp extremity. The micromechanical properties determined by nanoindentation and microhardness tests are almost insensitive to the cooling rate but are strongly affected by the STT; the higher the STT, the lower the overall microhardness of the Ti-6Al-4V alloy. In addition, the STT affects the microhardness and the Young’s modulus of both α and β phases differently; when the STT increases, the microhardness and the Young’s modulus of the α phase decrease, whereas those of the β phase increases.

36 MATERIALS SCIENCE↗

Ab Initio Modeling of fcc Fe-Co-Cr-Ni High Entropy Alloys with Full Composition Range

The Fe-Co-Cr-Ni quaternary system has been studied extensively in the past decade, not only because of the superior properties achieved like high tensile ductility and fracture toughness, but also it is the foundation for the development of FeCrCoNi-based HEAs. However, most of the investigations are mainly focusing on the equiatomic and semi-equiatomic compositions. The physical properties of non-equiatomic compositions are barely explored. In the current work, the ab initio approach is adopted to predict the lattice parameter, structure stabilities, elastic properties, and enthalpy of formations of fcc Fe-Cr-Co-Ni HEA single crystals with the special quasirandom structure (SQS) method. To expand the design of Fe-Co-Cr-Ni HEAs into a full composition range, the current simulations cover all the binaries, ternaries, and the whole quaternary system. The 2-D composition-property contour diagrams are created to show the physical properties in the ternary and quaternary systems. Furthermore, our investigation shows that the fcc alloys' lattice parameter increases with the addition of Fe and Cr and decreases with Ni and Co. In addition to the enthalpy of formation at o K, the shape distortion rate is proposed to be another essential parameter to evaluate crystal stability. The results show the addition of Cr would destabilize the fcc lattice and cause symmetry breaking. Finally, the result of Pugh’s ratio shows that most of the fcc alloys show ductile behavior (P > 1.75), especially for the alloys around Fe 3 Ni, FeCo, and Fe 2 NiCo (P > 2.5). The brittle behavior (P < 1.75) is located around Fe 3 Cr and Fe 2 CoCr. Meanwhile, Cr 2 NiCo and Cr 2 FeNiCo are considered promising compositions to be tried and verified experimentally because of the higher bulk modulus and moderate shear modulus.

36 MATERIALS SCIENCE↗

Mechanical Properties of Uranium Silicides by Nanoindentation and Finite Elements Modeling

Three methods were used to measure the mechanical properties of U 3 Si, U 3 Si 2 , and USi. Quasi-static and continuous stiffness measurement nanoindentation were used to determine hardness and Young’s modulus, and microindentation was used to evaluate the bulk hardness. Hardness and Young’s modulus of the three U-Si compounds were both observed to increase with Si content. In conclusion, finite elements modelling was used to validate the nanoindentation data calculated for U 3 Si 2 and estimate its yield strength.

36 MATERIALS SCIENCE↗

Probing the Effect of Hydrogen on Elastic Properties and Plastic Deformation in Nickel Using Nanoindentation and Ultrasonic Methods

Hydrogen effects on small-volume plasticity and elastic stiffness constants are investigated with nanoindentation of Ni-201 and sonic velocity measurements of bulk Ni single crystals. Elastic modulus of Ni-201, calculated from indentation data, decreases ~22% after hydrogen charging. This substantial decrease is independently confirmed by sonic velocity measurements of Ni single crystals; c 44 decreases ~20% after hydrogen exposure. Furthermore, clear hydrogen-deformation interactions are observed. The maximum shear stress required to nucleate dislocations in hydrogen-charged Ni-201 is markedly lower than in as-annealed material, driven by hydrogen-reduced shear modulus. Additionally, a larger number of depth excursions are detected prior to general yielding in hydrogen-charged material, suggesting cross-slip restriction. Together, these data reveal direct correlation between hydrogen-affected elastic properties and plastic deformation in Ni alloys.

36 MATERIALS SCIENCE↗

Probing the Mechanical Performance of Micro-architected Porous Structures Through In Situ Characterization and Analysis

Micropores play critical roles in both natural and man-made materials. Such pores take on a variety of shapes and sizes ranging from spherical to irregular sphere-like voids with diameters spanning from the nanometer to millimeter scales. When porous structures are mechanically loaded, the pores direct the stress around their free surfaces, altering the material’s mechanical response relative to fully dense materials. In this study, for the first time, we create micro-architected porous samples using nanolithography and investigate the role of pore morphology by conducting a series of in situ micropillar compression tests in scanning electron microscopy. The findings demonstrate that porosity is the primary factor influencing the mechanical response of these micro-architected materials, as often seen on a macroscopic level. Additionally, we observed that pore geometry had a significant impact on Young’s modulus, yield stress, and strain energy density as a secondary parameter. Then, the extracted Young’s modulus was compared to macroscopic empirical models and determined the analytical models sufficiently described the impact of porosity in the microscopic scale but failed to capture the impact of second-order parameters. Furthermore, these results suggest how porous materials can be tailored to achieve desired mechanical properties based on the engineering applications of interest.

36 MATERIALS SCIENCE↗

First-principles study on the mechanical and thermodynamic properties of MoNbTaTiW

Refractory high-entropy alloys (RHEAs) are emerging as new materials for high temperature structural applications because of their stable mechanical and thermal properties at temperatures higher than 2273 K. In this study, the mechanical properties of MoNbTaTiW REDEA are examined by applying calculations based on first-principles density functional theory (DFT) and using a large unit cell with 100 randomized atoms. The phase calculation of MoNbTaTiW with CALPHAD method shows the existence of a stable body-centered cubic structure at a high temperature and a hexagonal closely packed phase at a low temperature. The predicted phase, shear modulus, Young’s modulus, Poisson’s ratio, and hardness values are consistent with available experimental results. The linear thermal expansion coefficient, vibrational entropy, and vibrational heat capacity of MoNbTaTiW RHEA are investigated in accordance with Debye-Grüneisen theory. These results may provide a basis for future research related to the application of RHEAs.

36 MATERIALS SCIENCE↗

Microstrain temperature evolution in beta-eurcryptite ceramics: Measurement and model

Mechanisms of microcracking and stress release in {beta}-eucryptite ceramics were investigated by applying a combination of neutron diffraction (ND), dilatometry and the Integrity Factor Model (IFM). It was observed that the macroscopic thermal expansion of solid samples closely follows the lattice thermal expansion as a function of temperature, and both are dominated by microcracks closing (during heating) and opening (during cooling). Analogous experiments on powders showed that the stresses that manifest peak shift are indeed relieved by comminution, and that the resulting lattice thermal expansion can be considered as unconstrained. By means of Rietveld refinement of the ND data, the evolution with temperature of peak width parameters linked to strain distributions along the basal, pyramidal and axial planes could also be extracted. The peak width parameters S{sub HKL} correlated well with the strains calculated by peak shift and with the model results. Furthermore, while the peak shifts showed that the powders are basically stress free, the S{sub HKL} showed a strong evolution of the peak width. Powders carry, therefore, a measurable strain distribution inside the particles, owing to the thermal expansion anisotropy of the crystallites. The IFM allowed this behavior to be rationalized, and the effect of microcracking on thermal expansion to be quantified. Experimental data allowed accurate numerical prediction of microcracking on cooling and of the evolution of microstresses. They also allowed the derivation of the material elastic modulus from bulk thermal expansion curves through the IFM concept. Ultrasound resonance measurements of the elastic modulus strongly support these theoretical predictions.

36 MATERIALS SCIENCE↗

On capturing the grain-scale elastic and plastic anisotropy of alpha-Ti with spherical nanoindentation and electron back-scattered diffraction

Here, spherical nanoindentation combined with electron back-scattered diffraction has been employed to characterize the grain-scale elastic and plastic anisotropy of single crystal alpha-Ti of two different compositions (in two different titanium alloys). Data analyses protocols needed to reliably extract the desired properties of interest are extended and demonstrated in this paper. Specifically, the grain-scale mechanical response is extracted in the form of indentation stress-strain curves for commercially pure (CP-Ti) alpha-Ti and alloyed (Ti-64) titanium from measurements on polycrystalline samples. The results are compared with responses of single crystals and nanoindentation tests (hardness and modulus) from the literature, and the measured indentation moduli are validated using crystal-elastic finite element simulations. The results obtained in this study show that (i) it is possible to characterize reliably the elastic and plastic anisotropy of alpha-Ti (hcp) of varying alloying contents with spherical nanoindentation stress-strain curves, (ii) the indentation modulus of alpha-Ti-64 is 5–10% less than CP-Ti, and (iii) the indentation yield strength of alpha-Ti-64 is 50–80% higher than CP-Ti.

36 MATERIALS SCIENCE↗

The effect of grain orientation on nanoindentation behavior of model austenitic alloy Fe-20Cr-25Ni

Instrumented nanoindentation was used in this paper to investigate the hardness, elastic modulus, and creep behavior of an austenitic Fe-20Cr-25Ni model alloy at room temperature, with the indented grain orientation being the variant. The samples indented close to the {111} surfaces exhibited the highest hardness and modulus. However, nanoindentation creep tests showed the greatest tendency for creep in the {111} indented samples, compared with the samples indented close to the {001} and {101} surfaces. Scanning electron microscopy and cross-sectional transmission electron microscopy revealed slip bands and dislocations in all samples. The slip band patterns on the indented surfaces were influenced by the grain orientations. Deformation twinning was observed only under the {001} indented surfaces. Finally, microstructural analysis and molecular dynamics modeling correlated the anisotropic nanoindentation-creep behavior with the different dislocation substructures formed during indentation, which resulted from the dislocation reactions of certain active slip systems that are determined by the indented grain orientations.

36 MATERIALS SCIENCE↗

Phase field simulation of martensitic transformation in pre-strained nanocomposite shape memory alloys

We show in this paper how strain engineering alters the fundamental characteristic of a martensitic transformation (MT) and gives it a new set of properties including large quasi-linear elastic strain response with nearly vanishing hysteresis and low elastic modulus. The work is motivated and inspired by a recent experimental study on elastic and inelastic (transformation) strain matching in a pre-strained nano-composite with Nb nanowires embedded in a NiTi shape memory alloy matrix. In particular, we demonstrate by computer simulation that dislocations at Nb/NiTi interfaces produced by the pre-straining are responsible for the unprecedented properties. Microstructural evolution captured in the simulations reveals that local stress fields associated with the dislocations regulate the nucleation and growth of martensite, turning the otherwise sharp, strong first-order transition into a continuous, high-order like transition. The simulations predict that the stress-strain hysteresis and modulus of the composite decrease with increasing amount of pre-strain, which agrees well with the experimental measurement. This study suggests a design strategy by introducing non-uniform stress fields for enhanced properties of shape memory alloys.

36 MATERIALS SCIENCE↗

Hydrogen Bonding Stiffens Peptide Amphiphile Supramolecular Filaments by Aza-Glycine Residues

Peptide amphiphiles (PAs) are a class of molecules comprised of short amino acid sequences conjugated to hydrophobic moieties that may exhibit self-assembly in water into supramolecular structures. Here, we investigate here how mechanical properties of hydrogels formed by PA supramolecular nanofibers are affected by hydrogen bond densities within their internal structure by substituting glycine for aza-glycine (azaG) residues. We found that increasing the number of PA molecules that contain azaG up to 5 mol% in PA supramolecular nanofibers increases their persistence length fivefold and decreases their diffusion coefficients as measured by fluorescence recovery after photobleaching. When these PAs are used to create hydrogels, their bulk storage modulus (G') was found to increase as azaG PA content in the supramolecular assemblies increases up to a value of 10 mol% and beyond this value a decrease was observed, likely due to diminished levels of nanofiber entanglement in the hydrogels as a direct result of increased supramolecular rigidity. Interestingly, we found that the bioactivity of the scaffolds toward dopaminergic neurons derived from induced pluripotent stem cells can be enhanced directly by persistence length independently of storage modulus. We hypothesize that this is due to interactions between the cells and the extracellular environment across different size scales: from filopodia adhering to individual nanofiber bundles to cell adhesion sites that interact with the hydrogel as a bulk substrate. Fine tuning of hydrogen bond density in self-assembling peptide biomaterials such as PAs provides an approach to control nanoscale stiffness as part of an overall strategy to optimize bioactivity in these supramolecular systems. supramolecular biomaterials.

36 MATERIALS SCIENCE↗

Determination of melt processing conditions for high performance amorphous thermoplastics for large format additive manufacturing

As the application space for large-scale 3D printed components continues to grow, it is necessary to identify appropriate processing conditions for high-performance thermoplastics on large format Additive Manufacturing (LFAM) systems. This study compares the rheological behavior of a high-performance thermoplastic, polyphenylsulfone (PPSU), with that of a commonly used low-temperature polymer, acrylonitrile butadiene styrene (ABS), to identify suitable processing conditions for large format AM systems. The linear viscoelastic properties (complex viscosity, storage modulus, loss modulus, and tan delta) of these materials are evaluated as a function of temperature, angular frequency, and carbon fiber content. Over the range of frequencies of interest to LFAM (10–100 rad/s), ABS behaves more like an elastic solid whereas PPSU behaves more like a viscous liquid. Here, the addition of 20–35% by weight of carbon fiber increased the shear thinning effect of both thermoplastics, showing a potential variation of 2–3 x over the range of expected LFAM extrusion shear rates (10–100 s –1 ).

36 MATERIALS SCIENCE↗