Search NASA⌕ Search

SEARCH · Search NASA

Results for “PROFILE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

The Activity Profiles and Peak Flux of Radar Meteor Showers

Meteor showers are transient phenomena; a limited duration is what distinguishes a shower from a sporadic source. They do not, however, have clear start and end times; instead, shower activity gradually (or rapidly) increases over time, reaches a peak, and then decays. In this report, we examine the activity profiles of 38 meteor showers using 20 years of single-station shower fluxes from the Canadian Meteor Orbit Radar (CMOR). We find that a number of showers, such as the Southern delta Aquariids (SDAs), exhibit a broad maximum in activity rather than a sharp peak. We also find that approximately one-third of showers exhibit asymmetric activity profiles in which the rate in which activity rises prior to the peak differs from the rate at which it decays after the peak. We provide a functional form for meteor shower activity profiles that incorporates these features and use these profile fits to estimate each shower’s peak flux. This report also includes an uncertainty analysis for CMOR fluxes. This includes the first (to our knowledge) characterization of systematic uncertainty in radar meteor fluxes.

A V Moorhead↗

Optimal Mission Profile for Low-Boom Supersonic Aircraft

An optimal mission profile, called the low-boom mission profile, is proposed for low-boom supersonic aircraft. The low-boom mission profile uses a fixed AoA for the cruise segment until reaching the cruise ceiling. The fixed AoA is determined by the cruise condition for the low-boom shaping of the aircraft. The derived CL trajectory is not necessarily the optimal trajectory for the cruise range when unrestricted supersonic flight is allowed. The undertrack sonic boom ground noise level is reduced during the cruise because of the increasing altitude from the fixed AoA trajectory and the approximate invariance of nondimensional overpressure at 3BL below a supersonic aircraft with respect to cruise altitude change when the AoA and cruise Mach are fixed. The approximate invariance of nondimensional overpressure at 3BL below a supersonic aircraft is verified using both Euler and Reynolds-averaged Navier-Stokes CFD solvers. A low-boom supersonic transport concept is used to illustrate that, compared to the fixed cruise altitude trajectory, the low-boom mission profile can increase the cruise range of a low-boom aircraft and reduce the undertrack sonic boom ground noise levels for the entire cruise segment. One significant contribution of this paper is the implication that an aircraft OML satisfying a sonic boom ground noise level constraint at SOC will satisfy the same noise level constraint over the entire cruise segment, as long as a fixed AoA trajectory is flown.

Low-boom characteristics↗

Effect of Control Blade History, and Axial Coolant Density and Burnup Profiles on BWR Burnup Credit

A technical basis for peak reactivity boiling water reactor (BWR) burnup credit (BUC) methods was recently generated, and the technical basis for extended BWR BUC is now being developed. In this paper, a number of effects related to extended BWR BUC are analyzed, including three major operational effects in BWRs: the coolant density axial distribution, the use of control blades during operation, and the axial burnup profile. Specifically, uniform axial moderator density profiles are analyzed and compared to previous results and an additional temporal fidelity study combing moderator density profiles for three different fuel assemblies is presented. Realistic control blade histories and cask criticality results are compared to previously generated constructed control blade histories. Finally, a preliminary study of the axial burnup profile is provided.

Marshall, William BJ J↗

Glprof: A Gprof inspired, Callgraph-oriented Per-Object Disseminating Memory Access Multi-Cache Profiler

Application analysis is facilitated through a number of program profiling tools. The tools vary in their complexity, ease of deployment, design, and profiling detail. Specifically, understand- ing, analyzing, and optimizing is of particular importance for scientific applications where minor changes in code paths and data-structure layout can have profound effects. Understanding how intricate data-structures are accessed and how a given memory system responds is a complex task. In this paper we describe a trace profiling tool, Glprof, specifically aimed to lessen the burden of the programmer to pin-point heavily involved data-structures during an application's run-time, and understand data-structure run-time usage. Moreover, we showcase the tool's modularity using additional cache simulation components. We elaborate on the tool's design, and features. Finally we demonstrate the application of our tool in the context of Spec bench- marks using the Glprof profiler and two concurrently running cache simulators, PPC440 and AMD Interlagos.

Janjusic, Tommy↗

Aerosol Vertical Profiling at Oliktok Point (AVPOP) Field Campaign Report

Aerosols are an important component of the atmospheric system through their various impacts on climate. Notably, the largest uncertainty of the energy budget (i.e., radiative forcing estimate) is the aerosol indirect effect. Aerosol-induced microphysical modifications influence cloud lifetime and albedo. However, constraining aerosol-cloud impacts in climate models, specifically in regions such as the Arctic, remains a significant challenge due to limited observations. The efficacy of an aerosol to impact the arctic energy budget largely depends on its concentration, composition, and source. While ground-based measurements will provide a consistent, high-resolution time series of aerosol observations, the arctic atmosphere can be stratified, and thus what is observed on the ground may not be representative of the aerosol aloft. A key gap in arctic aerosol research is routine vertical profiling of abundance and source characterization. Previous work outside of the Arctic has focused on using launched or tethered balloon systems (LBS and TBS, respectively) to measure vertical profiles of aerosol size distributions and has demonstrated the utility of such observations (e.g., Hofmann et al. 1989; Hofmann 1993; Iwasaka et al. 2003; Kim et al. 2003; Tobo et al. 2007). More specifically, particle spectrometers have also been deployed via TBS systems (de Boer et al. 2018; Greenberg et al. 2009; Maletto et al. 2003; Renard et al. 2016; Wehner et al. 2007; Siebert et al. 2004) affording information on aerosol layer locations and evolution by means of multiple profiles. Filter samples for post-processing of aerosol composition and ice nucleation properties have also been conducted in mid-latitudes (Creamean et al. 2018). However, while these studies present novel measurements of aerosol vertical profiling via balloon systems, few exist to date in the Arctic. The U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) user facility TBS is composed of a variety of winches, balloons, and instrumentation that flies within ARM’s Restricted Airspace (R-2204) at the third ARM Mobile Facility (AMF3) at Oliktok Point, Alaska (Figure 1). The system payload comprises instruments that can simultaneously collect in situ data on horizontal winds, ice microphysics, turbulence, thermodynamic state, aerosols, and the cloud-top environment (https://www.arm.gov/capabilities/instruments/tbs). Recent campaigns at AMF3 have involved the use of the ARM helikite, which is a balloon-kite hybrid that uses lighter-than-air principles to obtain its initial lift and a kite to achieve stability and dynamic lift. Additional information on the specifications of the helikite TBS can be found in the ARM TBS handbook (Dexheimer 2018).

Oliktok Point, North Slope of Alaska,, tethered ba↗

OpenACC Profiling Support for Clang and LLVM using Clacc and TAU

Since its launch in 2010, OpenACC has evolved into one of the most widely used portable programming models for accelerators on HPC systems today. Clacc is a project funded by the US Exascale Computing Project (ECP) to bring OpenACC support for C and C++ to the popular Clang and LLVM compiler infrastructure. In this paper, we describe Clacc's support for the OpenACC Profiling Interface, a critical component of the OpenACC specification that standardizes an interface that profiling tools and libraries can depend upon across OpenACC implementations. As part of Clacc's general strategy to build OpenACC support upon OpenMP, we describe how Clacc builds OpenACC Profiling Interface support upon an extended version of OMPT. We then describe how a major profiling and tracing toolkit within ECP, the TAU Performance System, takes advantage of this support. We also describe TAU's selective instrumentation support for OpenACC. Finally, using Clacc and TAU, we present example visualizations for several SPEC ACCEL OpenACC benchmarks running on an IBM AC922 node, and we show that the associated performance overhead is negligible.

Coti, Camille↗

Polycyclic aromatic hydrocarbon emission profiles and removal efficiency by electrostatic precipitator and wetfine scrubber in an iron ore sintering plant

A monitoring campaign of polychlorinated dibenzo-p-dioxins and dibenzofurans, polyaromatic hydrocarbons (PAHs), and polychlorinated biphenyl was carried out in an Italian iron ore sintering plant by sampling the combustion gases at the electrostatic precipitator (ESP) outlet, at the Wetfine scrubber (WS) outlet, and by collecting the ESP dust. Few data are available on these micropollutants produced in iron ore sintering plants, particularly from Italian plants. This study investigates the PAH emission profiles and the removal efficiency of ESPs and WS. PAHs were determined at the stack, ESP outlet flue gases, and in ESP dust to characterize the emission profiles and the performance of the ESP and the WS for reducing PAH emission. The 11 PAHs monitored are listed in the Italian legislative decree 152/2006. The mean total PAH sum concentration in the stack flue gases is 3.96 {mu}g/N m{sup 3}, in ESP outlet flue gases is 9.73 {mu}g/N m{sup 3}, and in ESP dust is 0.53 {mu}g/g. Regarding the emission profiles, the most abundant compound is benzo(b)fluoranthene, which has a relative low BaP toxic equivalency factors (TEF) value, followed by dibenzo(a,l)pyrene, which has a very high BaP(TEF) value. The emission profiles in ESP dust and in the flue gases after the ESP show some changes, whereas the fingerprint in ESP and stack flue gases is very similar. The removal efficiency of the ESP and of WS on the total PAH concentration is 5.2 and 59.5%, respectively. 2 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Modification of divertor heat and article flux profiles with applied 3D fields in NSTX H-mode plasmas

Externally imposed non-axisymmetric magnetic perurbations are observed to alter divertor heat and particle flux profiles in the National Spherical Torus Experiment (NSTX). The divertor profiles are foud to have a modust level of multiple local peaks, characteristic of strike poimt splitting or the "magnetis lob" structure, even before the application of the 3D fields in some (but not all) NSTX discharges. This is thought to be due to the intrinsic error fields. The applied 3D fields augmented the intrinsic strike point splitting, making the ampliture of local peaks, and valleys larger in the divertor profile and striations at the divertor surface brighter. The measured heat flux profile shows that the radial location and spacing of the strations are qualitativel consistent witth a vacuum field tracing calcultion. 3D field application did not change the peak divertor heat and particle fluxes at the toroidal location of measurement. Spatial characteristics of the observed patterns are also reported in the paper.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Detonation wave profiles measured in plastic bonded explosives using 1550 nm photon doppler velocimetry (PDV)

We present detonation wave profiles measured in two TATB based explosives and two HMX based explosives. Profiles were measured at the interface of the explosive and a Lithium-Fluoride (LiF) window using 1550 nm Photon Doppler Velocimetry (PDV). Planar detonations were produced by impacting the explosive with a projectile launched in a gas-gun. The impact state was varied to produce varied distance to detonation, and therefore varied support of the Taylor wave following the Chapman-Jouget (CJ) or sonic state. Profiles from experiments with different support should be the same between the Von-Neumann (VN) spike and CJ state and different thereafter. Comparison of profiles with differing support, therefore, allows us to estimate reaction zone lengths. For the TATB based explosive, a reaction zone length of {approx} 3.9 mm, 500 ns was measured in EDC-35, and a reaction zone length of {approx} 6.3 mm, 800 ns was measured in PBX 9502 pre-cooled to -55 C. The respective VN spike state was 2.25 {+-} 0.05 km/s in EDC-35 and 2.4 {+-} 0.1 km/s in the cooled PBX 9502. We do not believe we have resolved either the VN spike state (> 2.6 km/s) nor the reaction zone length (<< 50 ns) in the HMX based explosives.

36 MATERIALS SCIENCE↗

Thermodynamic and liquid profiling during the 2010 Winter Olympics

Tropospheric observations by a microwave profiling radiometer and six-hour radiosondes were obtained during the Alpine Venue of the 2010 Winter Olympic Games at Whistler, British Columbia, by Environment Canada. The radiometer provided continuous temperature, humidity and liquid (water) profiles during all weather conditions including rain, sleet and snow. Gridded analysis was provided by the U.S. National Oceanic and Atmospheric Administration. We compare more than two weeks of radiometer neural network and radiosonde temperature and humidity soundings including clear and precipitating conditions. Corresponding radiometer liquid and radiosonde wind soundings are shown. Close correlation is evident between radiometer and radiosonde temperature and humidity profiles up to 10 km height and among southwest winds, liquid water and upper level thermodynamics, consistent with up-valley advection and condensation of moist maritime air. We compare brightness temperatures observed by the radiometer and forward-modeled from radiosonde and gridded analysis. Radiosonde-equivalent observation accuracy is demonstrated for radiometer neural network temperature and humidity retrievals up to 800 m height and for variational retrievals that combine radiometer and gridded analysis up to 10 km height

54 ENVIRONMENTAL SCIENCES↗

Laser wire beam profile monitor in the Spallation Neutron Source (SNS) superconducting linac

The Spallation Neutron Source (SNS) at Oak Ridge National Laboratory is an accelerator based neutron scattering facility. The SNS uses the large scale high energy superconducting linac (SCL) to provide high beam power utilizing hydrogen ion (H-) beams. For the diagnostics of high-brightness H- beam in the SCL, nonintrusive methods have to be developed. This paper describes design, implementation, theoretical analysis and experimental demonstration of a nonintrusive profile monitor system based on photodetachment, also known as laser wire, installed in the SNS-SCL. The SNS laser wire system is the largest of its kind with a capability of measuring both horizontal and vertical profiles of an operational H- beam at each of the 23 cryomodule stations along the SCL beam line by employing a single light source. Presently 9 laser wire stations have been commissioned which measures H- beam profiles at 9 different locations corresponding to energy levels of 200 MeV to 1 GeV. The laser wire diagnostics has no moving parts inside the beam pipe, causes no contamination on the superconducting surface, and can be run parasitically on an operational neutron production H- beam.

43 PARTICLE ACCELERATORS↗

CROCUS Sodar Measurements of Lower Atmospheric Wind Profiles at Argonne Testbed for Multiscale Observational Science (ATMOS) Site

The Scintec MFAS Sodar (Multiple-Frequency Acoustic Sounder) is an autonomous, ground-based acoustic remote sensing system designed to measure vertical profiles of horizontal wind speed, wind direction, and vertical velocity in the lower atmosphere. The instrument transmits sequences of acoustic pulses and detects the Doppler-shifted sound waves backscattered by small-scale temperature and velocity fluctuations caused by atmospheric turbulence. From these Doppler shifts, the system derives three-dimensional wind vectors by combining radial velocities from multiple beam orientations.The MFAS Sodar operates with a first usable range gate beginning at approximately 30 m above ground level and a configurable vertical resolution of 10 m. Under favorable acoustic conditions, the system provides wind profiles extending up to 600 m above ground level. Measurements are processed into 15-minute averaged profiles containing wind speed, direction, vertical velocity, and diagnostic quantities such as signal-to-noise ratio and echo strength.This dataset was collected at the Argonne Testbed for Multiscale Observational Science (ATMOS) facility in Lemont, Illinois, as part of DOE's CROCUS Urban Integrated Field Laboratory (UIFL) initiative. The purpose of these observations is to characterize the vertical wind structure and boundary-layer evolution across the urban–suburban gradient of the greater Chicago region. In particular, these data are intended to improve understanding of how local meteorology, such as lake-breeze penetration, nocturnal jets, and daytime mixing, varies between the densely built urban core and the suburban periphery. The MFAS observations provide critical context for evaluating high-resolution model simulations and for integrating with complementary lidar, radar, and in-situ meteorological measurements within the broader CROCUS UIFL network.All data are archived in NetCDF (Network Common Data Form) format and include wind and diagnostic parameters. The files can be accessed and analyzed using standard software that supports NetCDF, such as Python (e.g., xarray, netCDF4), MATLAB, R (e.g., ncdf4, raster), or Panoply (NASA’s NetCDF visualization application).

54 ENVIRONMENTAL SCIENCES↗

The Convolutional Multiple Whole Profile (CMWP) Fitting Method, a Global Optimization Procedure for Microstructure Determination

The analysis of line broadening in X-ray and neutron diffraction patterns using profile functions constructed on the basis of well-established physical principles and TEM observations of lattice defects has proven to be a powerful tool for characterizing microstructures in crystalline materials. These principles are applied in the convolutional multiple-whole-profile (CMWP) procedure to determine dislocation densities, crystallite size, stacking fault and twin boundary densities, and intergranular strains. The different lattice defect contributions to line broadening are separated by considering the hkl dependence of strain anisotropy, planar defect broadening and peak shifts, and the defect dependent profile shapes. The Levenberg–Marquardt (LM) peak fitting procedure can be used successfully to determine crystal defect types and densities as long as the diffraction patterns are relatively simple. However, in more complicated cases like hexagonal materials or multiple-phase patterns, using the LM procedure alone may cause uncertainties. Here, we extended the CMWP procedure by including a Monte Carlo statistical method where the LM and a Monte Carlo algorithm were combined in an alternating manner. The updated CMWP procedure eliminated uncertainties and provided global optimized parameters of the microstructure in good correlation with electron microscopy methods.

36 MATERIALS SCIENCE↗

Optimal control of the electron temperature profile in DIII-D using machine learning surrogate models

The viability of the tokamak as a potential fusion reactor depends on the ability to keep the plasma in a stable regime while achieving temperatures, densities, and confinement times that are as high as possible. Tokamak scenario development attempts to find plasma regimes that achieve all of these conditions and are accessible with a given set of hardware constraints. This requires the ability to control plasma properties such as the normalized beta, the internal inductance, safety factor, rotation, etc. One property that has received less attention than some of the others, but is no less critical to achieving high performance, is the electron temperature (T e ) profile. In this work, Linear Quadratic Integral (LQI) control is used to develop a controller for the electron temperature profile in DIII-D. The controller is based on a linearized model derived from the transport equation that describes the evolution of the electron temperature, and includes contributions from the neural network surrogate models NubeamNet and MMMnet. Furthermore, the controller is tested in simulation using COTSIM, and is proven capable of tracking a target T e profile.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Modeling the impact of radiation-enhanced diffusion on implanted ion profiles

We report that ion irradiations are a valuable research tool for exploring radiation effects in materials. However, it is well recognized that the implanted ions can artificially modify the radiation damage evolution, e.g., enhancing amorphization processes at low irradiation temperatures and suppressing void swelling at elevated temperatures. Therefore, the implanted ion region should be avoided for most studies of ion irradiated materials. Due to increased interest in high damage, high temperature ion irradiations studying radiation effects in materials for proposed high dose Generation IV fission and fusion energy applications, it is crucial to quantify the extent of diffusional broadening of the implanted ion profile for a variety of temperatures, irradiation fluxes, and sink strengths. The present study summarizes computational analyses of thermal and depth-dependent radiation enhanced difusion (RED) on diffusion broadening of the implanted ion profiles in Fe and Ni for a variety of irradiation conditions. For a low assumed RED coefficient (10 -20 -10 -19 m 2 /s and 10 -4 and 10 -3 peak dpa/s, respectively) or high flux, broadening of the as-implanted ion profile is very small and a suitable artifact-free midrange region for analysis exists for ion energies above 5-6 MeV at 100 peak dpa. At high RED coefficients (10 -19 -10 -18 m 2 /s and 10 -4 and 10 -3 peak dpa/s, respectively) broadening is much more significant, and no valid region for investigation exists below 6-8 MeV ion energies at any damage level >50 dpa. While increasing flux decreases irradiation time, it also increases the RED coefficient; these effects mostly offset except under recombination-dominant conditions. For typical high dose irradiation studies of void swelling that exceed ~100 displacement per atom (dpa), ion energies > 6-8 MeV must be employed in order to achieve suitable artifact-free midrange irradiation analysis regions, depending on the material system. Lastly, analysis of amorphization/precipitation require even higher energies (>10 MeV).

07 ISOTOPE AND RADIATION SOURCES↗

Synapse: Synthetic application profiler and emulator

Abstract Motivated by the need to emulate workload execution characteristics on high- performance and distributed heterogeneous resources, we introduce Synapse. Synapse is used as a proxy application (or "representative application") for real workloads, with the advantage that it can be tuned in different ways and dimensions, and also at levels of granularity that are not possible with real applications. Synapse has a platform-independent application profiler, and has the ability to emulate profiled workloads on a variety of resources. Experiments show that the automated profiling performed using Synapse captures an application's characteristics with high fidelity. The emulation of an application using Synapse can reproduce the application's execution behavior in the original run- time environment, and can also reproduce those behaviors on different run-time environments.

97 MATHEMATICS AND COMPUTING↗

Beam Profile Disturbances from Implantable Pacemakers or Implantable Cardioverter-Defibrillator Interactions

The medical community is advocating for progressive improvement in the design of implantable cardioverter-defibrillators and implantable pacemakers to accommodate elevations in dose limitation criteria. With advancement already made for magnetic resonance imaging compatibility in some, a greater need is present to inform the radiation oncologist and medical physicist regarding treatment planning beam profile changes when such devices are in the field of a therapeutic radiation beam. Treatment plan modeling was conducted to simulate effects induced by Medtronic, Inc.-manufactured devices on therapeutic radiation beams. As a continuation of grant-supported research, we show that radial and transverse open beam profiles of a medical accelerator were altered when compared with profiles resulting when implantable pacemakers and cardioverter-defibrillators are placed directly in the beam. Results are markedly different between the 2 devices in the axial plane and the sagittal planes. Vast differences are also presented for the therapeutic beams at 6-MV and 18-MV x-ray energies. Maximum changes in percentage depth dose are observed for the implantable cardioverter-defibrillator as 9.3% at 6 MV and 10.1% at 18 MV, with worst distance to agreement of isodose lines at 2.3 cm and 1.3 cm, respectively. For the implantable pacemaker, the maximum changes in percentage depth dose were observed as 10.7% at 6 MV and 6.9% at 18 MV, with worst distance to agreement of isodose lines at 2.5 cm and 1.9 cm, respectively. No differences were discernible for the defibrillation leads and the pacing lead.

61 RADIATION PROTECTION AND DOSIMETRY↗