Search NASA⌕ Search

SEARCH · Search NASA

Results for “Pressure Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Pressure distributions on three different cruciform aft-tail control surfaces of a wingless missile at mach 1.60, 2.36, and 3.70 Volume 1: Trapezoidal tail

The results of pressure distribution tests conducted in the Langley Unitary Plan wind tunnel are presented. The data were obtained for three sets of cruciform aft-tail control surfaces on a wingless missile model at Mach numbers of 1.60, 2.36, and 3.70 for angles of attack from -4 degrees to 20 degrees, model roll angles from 0 degrees to 90 degrees, and tail deflections of 0 degrees and 15 degrees. The test Reynolds number used was 6.6 million per meter.

Lamb, M.↗
NASA NTRS1979

Design, fabrication and delivery of a high pressure LOX-methane injector

An injector for 3000 psia chamber pressure using liquid oxygen and gaseous methane propellants is presented. The injector is intended to be evaluated during a series of pressure-fed test firings using a water-cooled calorimeter chamber and a milled-slot regenerative chamber. Combustion efficiency, combustion stability, ignition and injector face heat transfer assessments were made for candidate injector body and pattern design approaches. This evaluation resulted in baselining an oxidizer post type manifold with a 60 element platelet coaxial swirler injector pattern. An axial acoustic resonator cavity was created at the injector/chamber interface.

Valler, H. W.↗
NASA NTRS1981

Experiments on the nonlinear characteristics of noise propagation from low and moderate Reynolds number supersonic jets

A series of experiments were conducted on high-speed model jets to identify and quantify the distortion of radiated noise by nonlinear propagation effects. The jets were operated in a low to moderate Reynolds number range, and the radiated noise was either broadband or discrete in frequency. Three condenser microphones were used to measure the waveforms propagated by the axisymmetric, cold model jets of Mach numbers 2.1 and 2.5. Relatively low Reynolds numbers were obtained by exhausting the jets into a low pressure anechoic test chamber. Nonlinear propagation distortion effects, such as wave steepening, harmonic generation and wave merging, were easily quantified. At a moderate Reynolds number, low frequency production and wave amalgamation, measured by a decrease in the zero crossings per unit time, were quantified in the propagation of sound away from the jet.

Gallagher, J. A.↗
NASA NTRS1979

Pressure distributions on three different cruciform aft-tail control surfaces of a wingless missile at Mach 1.60, 2.36, and 3.70. Volume 1: Trapezoidal tail

The results of pressure distribution tests conducted in a wind tunnel are presented without analysis. The data were obtained for trapezoidal aft tail control surfaces on a wingless missile model at Mach numbers of 1.60, 2.36, and 3.70 for angles of attack from -4 to 20 deg model roll angles from 0 to 90 deg and tail deflections of 0 and -15 deg. The test Reynolds number used was 6.6 million per meter.

Lamb, M.↗
NASA NTRS1982

The effect of non-linear propagation in jet noise

An experimental investigation of the nonlinear propagation effects which occur in the noise radiated from low and moderate Reynolds number supersonic jets has been performed. An array of three condenser microphones was used to measure the waveforms propagated by axisymmetric, cold model jets of Mach numbers 2.1 and 2.5. Relatively low Reynolds numbers were obtained by exhausting the jets into a low pressure anechoic test chamber. The results show that phenomena normally associated with nonlinear acoustic propagation, such as wave steepening, harmonic generation and wave merging, are measurable in the high speed model jets.

Gallagher, J. A.↗
NASA NTRS1985

Dynamic Calibration of Pressure Transducers

Sinusoidal calibration signal produced in 4- to 100-Hz range. Portable oscillating-pressure device measures dynamic characteristics of pressure transducers installed in models or aircraft at frequency and oscillating-pressure ranges encountered during unsteady-pressure-measurement tests. Calibration is over range of frequencies and amplitudes not available with commercial acoustic calibration devices.

Hess, R. W.↗
NASA NTRS1984

Antimisting kerosene: Base fuel effects, blending and quality control techniques

The problems associated with blending of the AMK additive with Jet A, and the base fuel effects on AMK properties are addressed. The results from the evaluation of some of the quality control techniques for AMK are presented. The principal conclusions of this investigation are: significant compositional differences for base fuel (Jet A) within the ASTM specification DI655; higher aromatic content of the base fuel was found to be beneficial for the polymer dissolution at ambient (20 C) temperature; using static mixer technology, the antimisting additive (FM-9) is in-line blended with Jet A, producing AMK which has adequate fire-protection properties 15 to 20 minutes after blending; degradability of freshly blended and equilibrated AMK indicated that maximum degradability is reached after adequate fire protection is obtained; the results of AMK degradability as measured by filter ratio, confirmed previous RAE data that power requirements to decade freshly blended AMK are significantly higher than equilibrated AMK; blending of the additive by using FM-9 concentrate in Jet A produces equilibrated AMK almost instantly; nephelometry offers a simple continuous monitoring capability and is used as a real time quality control device for AMK; and trajectory (jet thurst) and pressure drop tests are useful laboratory techniques for evaluating AMK quality.

Yavrouian, A. H.↗
NASA NTRS1983

Aerodynamic design using numerical optimization

The procedure of using numerical optimization methods coupled with computational fluid dynamic (CFD) codes for the development of an aerodynamic design is examined. Several approaches that replace wind tunnel tests, develop pressure distributions and derive designs, or fulfill preset design criteria are presented. The method of Aerodynamic Design by Numerical Optimization (ADNO) is described and illustrated with examples.

Murman, E. M.↗
NASA NTRS1984

An experimental investigation of two-dimensional thrust augmenting ejectors, part 2

The flow-field within a two-dimensional thrust augmenting ejector has been documented experimentally. Results are presented on the mean velocity field and the turbulent correlations by Laser Doppler Velocimeter, surface pressure distribution, surface temperature distribution, and thrust performance for two shroud geometries. The maximum primary nozzle pressure ratio tested was 3.0. The tests were conducted at primary nozzle temperature ratios of 1.0, 1.8 and 2.7. Two ejector characteristic lengths have been identified based on the dynamics of the ejector flow field, i.e., a minimum length L sub m below which no significant mixing occurs, and a critical length L sub c associated with the development of U'V' correlation in the ejector. These characteristic lengths divide the ejector flow field into three distinctive regions: the entrance region where there is no direct interaction between the primary flow and the ejector shroud; the interaction region where there is an increased momentum of induced flow near the shroud surface; and a pipe flow region characterized by an increased skin friction where x is the distance downstream from the ejector inlet. The effect of the coflowing induced flow has been shown to produce inside the ejector a centerline velocity that has increased over the free-jet data.

Bernal, L.↗
NASA NTRS1985

Aerodynamics of sports balls

Research data on the aerodynamic behavior of baseballs and cricket and golf balls are summarized. Cricket balls and baseballs are roughly the same size and mass but have different stitch patterns. Both are thrown to follow paths that avoid a batter's swing, paths that can curve if aerodynamic forces on the balls' surfaces are asymmetric. Smoke tracer wind tunnel tests and pressure taps have revealed that the unbalanced side forces are induced by tripping the boundary layer on the seam side and producing turbulence. More particularly, the greater pressures are perpendicular to the seam plane and only appear when the balls travel at velocities high enough so that the roughness length matches the seam heigh. The side forces, once tripped, will increase with spin velocity up to a cut-off point. The enhanced lift coefficient is produced by the Magnus effect. The more complex stitching on a baseball permits greater variations in the flight path curve and, in the case of a knuckleball, the unsteady flow effects. For golf balls, the dimples trip the boundary layer and the high spin rate produces a lift coefficient maximum of 0.5, compared to a baseball's maximum of 0.3. Thus, a golf ball travels far enough for gravitational forces to become important.

Mehta, R. D.↗
NASA NTRS1986

Transmission electron microscopic examination of phosphoric acid fuel cell components

Transmission electron microscopy (TEM) was used to physically characterize tested and untested phosphoric acid fuel cell (PAFC) components. Those examined included carbon-supported platinum catalysts, carbon backing paper, and Teflon-bonded catalyst layers at various stages of fabrication and after testing in pressurized PAFC's. Applicability of electron diffraction and electron energy loss spectroscopy for identifying the various phases was explored. The discussion focuses on the morphology and size distribution of platinum, the morphology and structural aspects of Teflon in catalyst layers, and the structural evidence of carbon corrosion. Reference is made to other physical characterization techniques where appropriate. A qualitative model of the catalyst layer that emerged from the TEM studies is presented.

Pebler, A.↗
NASA NTRS1987

Combustion of velcro in low gravity

An experimental program was conducted to investigate the low gravity burning characteristics on nylon and Nomex Velcro fastening tapes in an atmosphere of 30-percent oxygen, 70-percent nitrogen at a 70-kPa pressure. The tests were conducted using the NASA Lewis Research Center Zero Gravity Facility. The test results, as documented by high-speed cameras, indicate that both nylon and Nomex burn in low gravity for the full 5.18 sec test time but that Nomex burns less vigorously than nylon. Nylon melts as it burns, whereas Nomex forms a solid char. Nylon also sputters burning droplets as it burns. Thus, from these limited tests, it appears that Nomex Velcro is less hazardous than nylon Velcro for spacecraft applications. The results also show that residual gas velocities, and by analogy spacecraft air circulation, can enhance the low-gravity combustion.

Olson, Sandra L.↗
NASA NTRS1987

A detailed description of the uncertainty analysis for High Area Ratio Rocket Nozzle tests at the NASA Lewis Research Center

A preliminary uncertainty analysis has been performed for the High Area Ratio Rocket Nozzle test program which took place at the altitude test capsule of the Rocket Engine Test Facility at the NASA Lewis Research Center. Results from the study establish the uncertainty of measured and calculated parameters required for the calculation of rocket engine specific impulse. A generalized description of the uncertainty methodology used is provided. Specific equations and a detailed description of the analysis are presented. Verification of the uncertainty analysis model was performed by comparison with results from the experimental program's data reduction code. Final results include an uncertainty for specific impulse of 1.30 percent. The largest contributors to this uncertainty were calibration errors from the test capsule pressure and thrust measurement devices.

Kenneth J. Davidian↗
NASA NTRS1988

Regenerative life support system research

Sections on modeling, experimental activities during the grant period, and topics under consideration for the future are contained. The sessions contain discussions of: four concurrent modeling approaches that were being integrated near the end of the period (knowledge-based modeling support infrastructure and data base management, object-oriented steady state simulations for three concepts, steady state mass-balance engineering tradeoff studies, and object-oriented time-step, quasidynamic simulations of generic concepts); interdisciplinary research activities, beginning with a discussion of RECON lab development and use, and followed with discussions of waste processing research, algae studies and subsystem modeling, low pressure growth testing of plants, subsystem modeling of plants, control of plant growth using lighting and CO2 supply as variables, search for and development of lunar soil simulants, preliminary design parameters for a lunar base life support system, and research considerations for food processing in space; and appendix materials, including a discussion of the CELSS Conference, detailed analytical equations for mass-balance modeling, plant modeling equations, and parametric data on existing life support systems for use in modeling.

Source record↗
NASA NTRS1987

A detailed description of the uncertainty analysis for high area ratio rocket nozzle tests at the NASA Lewis Research Center

A preliminary uncertainty analysis was performed for the High Area Ratio Rocket Nozzle test program which took place at the altitude test capsule of the Rocket Engine Test Facility at the NASA Lewis Research Center. Results from the study establish the uncertainty of measured and calculated parameters required for the calculation of rocket engine specific impulse. A generalized description of the uncertainty methodology used is provided. Specific equations and a detailed description of the analysis is presented. Verification of the uncertainty analysis model was performed by comparison with results from the experimental program's data reduction code. Final results include an uncertainty for specific impulse of 1.30 percent. The largest contributors to this uncertainty were calibration errors from the test capsule pressure and thrust measurement devices.

Davidian, Kenneth J.↗
NASA NTRS1987

Oxide-dispersion-strengthened turbine blades. Volume 2

The overall objective of Project 4 was to develop and test a high-temperature, uncooled gas turbine blade using MA6000 alloy. Production scale up of the MA6000 alloy was achieved with a fair degree of tolerance to non-optimum processing. The blade manufacturing process was also optimized. The mechanical, environmental, and physical property evaluations of MA6000 were conducted. The ultimate tensile strength, to about 704 C (1300 F), is higher than DS MAR-M 247 but with a corresponding lower tensile elongation. Also, above 982 C (1800 F) MA6000 tensile strength does not decrease as rapidly as MAR-M 247 because the ODS mechanism still remains active. Based on oxidation resistance and diffusional stability considerations, NiCrAlY coatings are recommended. CoCrAlY coating should be applied on top of a thin NiCrAlY coating if hot corrosion is expected. Vibration, whirlpit, and high-rotor-rig tests were conducted to ensure successful completion of the engine test of the MA6000 TFE731 high pressure turbine blades. Test results were acceptable. In production quantities, the cost of the Project 4 MA6000 blade is estimated to be twice that of a cast DS MAR-M 247 blade.

Millan, P. P., Jr.↗
NASA NTRS1989

CAP-TSD analysis of the F-15 aircraft

The F-15 fighter aircraft was modeled using Computational Aeroelasticity Program - Transonic Small Disturbance (CAP-TSD). The complete aircraft was modeled including the wing, stabilator, flow through inlets, and fuselage body. CAP-TSD was used to make static pressure runs for Mach numbers of 0.8, 0.9, 0.95 and 1.2. The angle of attack for these runs ranged from 0 to 5 degs. The CAP-TSD program showed good agreement between the computed fuselage and wing pressures and the measured wind tunnel pressures. Including the fuselage and inlets in the CAP-TSD analysis is important and improves the correlation of wing pressures with test data.

Pitt, Dale M.↗