'Radiation Protection Program: Radiological Engineering
This document describes plans for the radiation protection program.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This document describes plans for the radiation protection program.
The X-ray transport, optics and diagnostic system (XTOD) starts from the end of bending magnets sending electrons to the main dump and ends at the end wall separating the accelerator tunnel from the user experimental hall (hereafter referred as EH wall), as shown in Figure 1. Figure 1.a shows the general schematic and Figure 1.b shows the initial layout with possible shielding components. This document summarizes the extensive studies on the shielding and collimator system design necessary to meet the radiation protection requirements.
Health Physics is a profession dedicated to the protection of human health and the environment from the dangers of radiation and radioactivity WHILE providing for its beneficial use.
FEMP Water Efficiency Best Management Practice #14 Case Study: Overview of the air handler condensate recovery program at the Environmental Protection Agency's Science and Ecosystem Support Division.
We present an overview of the program on the evaluation methodology for proliferation resistance and physical protection (PR&PP) of advanced nuclear energy systems (NESs) sponsored by the Generation IV International Forum (GIF). For a proposed NES design, the methodology defines a set of challenges, analyzes system response to these challenges, and assesses outcomes. The challenges to the NES are the threats posed by potential actors (proliferant States or sub-national adversaries). The characteristics of Generation IV systems, both technical and institutional, are used to evaluate the response of the system and to determine its resistance against proliferation threats and robustness against sabotage and terrorism threats. The outcomes of the system response are expressed in terms of a set of measures, which are the high-level PR&PP characteristics of the NES. The methodology is organized to allow evaluations to be performed at the earliest stages of system design and to become more detailed and more representative as the design progresses. It can thus be used to enable a program in safeguards by design or to enhance the conceptual design process of an NES with regard to intrinsic features for PR&PP.
New technologies have been, and are continuing to be, developed for Safeguards, Arms Control, and Physical Protection. Application spaces and technical requirements are evolving - Overlaps are developing. Lessons learned from IAEA's extensive experience could benefit other communities. Technologies developed for other applications may benefit Safeguards - Inherent cost benefits and improvements in procurement security processes.
The Generation IV International Forum (GIF) “Technology Roadmap” identified proliferation resistance and physical protection (PR&PP) as one of the four goal areas to advance nuclear energy into its next, “fourth” generation. It recommended the development of a methodology to define measures for PR&PP and to evaluate them for the six nuclear energy systems selected by GIF. Accordingly, the Forum formed a PR&PP Working Group (PRPPWG) to develop a methodology and to define the parameters against which PR&PP would be measured. The PRPPWG developed the methodology through a series of development and demonstration case studies, by use of a hypothetical “Example Sodium Fast Reactor” (ESFR). The PR&PP ESFR assessment was the first opportunity to exercise the full methodology on a complete system, and many insights were gained from the process. The PRPPWG and representatives of the GIF System Steering Committees (SSCs) for each of the six GIF design concepts carried out a study on the PR&PP aspects of the six GIF designs. This interaction allowed the PRPPWG to engage the designers and to raise awareness about PR&PP. A number of international workshops have also been held which have introduced the methodology to design groups and other stakeholders. In this paper, we first summarize the technical progress and the major accomplishments of the PRPPWG: the evaluation methodology and the ESFR case study used to develop and test the methodology. The interaction with the GIF System Steering Committees and the relaunching of the activity is then presented. Finally, an outline of the future challenges is provided along the lines identified in the GIF R&D outlook 2018 report.
Digital technology has advantages over analog systems, including automated monitoring and alerts for standby safety functions, and predictive algorithms to maintain critical safety systems. Additionally, digital technology generally has higher reliability and can be designed to reduce single point vulnerabilities. For these reasons many nuclear plants have applied digital technology to safety and non-safety related applications, including reactor protection system, feedwater and turbine controls, etc. with a corresponding significant improvement in trip reduction. Nonetheless, digital instrumentation and control (I and C) systems also present potential new vulnerabilities that need to be assessed, including potential failures due to increased complexity of digital systems, the introduction of unique failure modes due to software (including software common cause failure (CCF)), and limited operating history of digital systems in nuclear safety related applications compared to analog systems. The fact that software is intangible means that common methods, such as analysis or testing, used for detecting CCF may not be effective when applied to software. Consequently, digital technology is perceived to pose a potential risk from the introduction of undetected systematic faults that could result in CCF. Despite the I and C system upgrades and modifications performed to date, the U.S. Nuclear Regulatory Commission (NRC) and industry stakeholders have identified the need to modernize the regulatory infrastructure to efficiently address risks associated with the use of digital technology for nuclear safety applications and address regulatory uncertainties. The NRC's current position on CCF is guided by the staff requirements memorandum (SRM) on SECY 93-087. The SRM provides specific acceptance criteria for the evaluation of CCF, which the staff implemented in the Branch Technical Position (BTP) 7-19. However, industry stakeholders have proposed using methods to characterize the likelihood of software CCF and eliminate it from further consideration in a defense-in-depth and diversity analysis. The NRC's current position does not consider these alternatives, and thus corresponding acceptance criteria is not currently available. The work discussed in this paper assesses the underlying technical basis associated with CCF, provides technical support for updating the NRC position and considers proposed methods for addressing potential CCF in digital systems while enhancing efficiency, clarity, and confidence. (authors)
In the last decades, electronic irradiation accelerator has made great progress and been widely used in fields. Because of its distinguishing feature of reliability and safety, electronic irradiation accelerator has attracted more attention of the investors, and created a huge economic value and social benefits. It will become the mainstream equipment of irradiation processing industry in future. So the further study of the shielding design around irradiation accelerator is of great significance. Different designs of ventilation duct will greatly influence dose rate of the exit. Because of the high dose rate under the target, it is suitable to use multi-tortuous duct when duct locating under target. It will reduce the dose rate about 3 orders of magnitude at the exit that add one backscattering interface in duct. Choose reasonable diameter and angle of embedded duct so that photons scatter as much as possible. We can use multiple small diameter ducts to replace large diameter duct. The system of Mini-DDL, Gamma detector and PC give a better reflection on the running statue of accelerator, its perfect usability can produce intuitive images for analyzed, it is important and helpful for workers and researchers to know about the radiation level of machine and environment. The measured results along the maze show that the maze must be long enough in order to achieve the desired shielding thickness. In future, we will combine the different kinds and motor patterns of body models, Monte Carlo programs, real time monitoring system with theoretical calculations to explore how the radiation field around accelerator has impact on human organs, get the dose distribution of body models so that improve the radiation protection to electron accelerator. (authors)
Experiments using the CALIBAN and PROSPERO reactors were performed in 2013 in the framework of a collaboration between IRSN and CEA. The objective was to provide data about the possibility to use information given by radiation protection instrumentations (RPI) in the case of a criticality accident. In that purpose, the behavior of RPI was studied for various kinetics of the reactors which simulated different starts of a criticality accident. The article presents the safety issues associated with these experiments, i.e. the possible use of information given by the RPI for the emergency response of a criticality accident (detection of the accident, triage of the personnel, follow-up of the accident and reentry). Then, one paragraph is dedicated to the presentation of the tested material. In addition, the CALIBAN and PROSPERO reactors are briefly described, followed by the performed experiments. The RPI are neither designed nor dedicated to be used in case of a criticality accident. However, the preliminary conclusion of the experiments performed in 2013 is that the tested RPI have a correct behavior for slow kinetic experiments performed with the PROSPERO reactor, but might give less reliable and accurate information for pulse experiments performed with the CALIBAN reactor. In the last case, they can nevertheless provide information that can be helpful for the emergency response and the limitation of the consequences of the criticality accident. However, if the RPI are included in the emergency response of a criticality accident (detection, triage, follow-up, reentry), emergency procedures should be adapted. Other experiments might be performed in order to confirm results and to extend the number of tested materials, in particular portable survey meters or contamination area monitors. (authors)
Here, small-diameter carbon nanotubes (CNTs) are shown to enable exceptionally fast transport of water vapor under a concentration gradient driving force. Thanks to this property, membranes having sub-5 nm CNTs as conductive pores feature outstanding breathability while maintaining a high degree of protection from biothreats by size exclusion.
Ti 3 C 2 – a member of the MXenes (2D transition metal carbides and nitrides) family, is investigated as an effective filler to improve the electrical, mechanical, and thermal properties of divinylbenzene (DVB) thermosetting resin. Consequently, its performance as a lightning strike protection (LSP) coating for carbon fiber reinforced polymer (CFRP) is evaluated. Polyaniline (PANI) – dodecylbenzene sulfonic acid (DBSA) complex is used to cure the DVB resin. The synergic effect of MXenes (with surface that is negatively charged) with polyaniline (positive charge) shows electrostatic bonding and improved electrical conductivity in the composite. We also find that the addition of MXenes at 2 wt% into the PANI-DVB composite shows ≈139%, 10%, and 9% improvement in electrical conductivity, flexural strength, and flexural modulus, respectively, compared to the neat PANI-DVB composite. The composites are investigated using various material characterization techniques including Fourier transforms infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and scanning electron microscopy. Furthermore, MXenes-DVB is utilized to create a conductive thermosetting coating on top of a CFRP substrate and tested against a lightning strike of 100 kA. CFRP with MXenes-DVB coating reduced the surface damage from 40.61 cm 2 (reference CFRP panel) to 13.29 cm 2 (CFRP coated with MXenes-DVB).
A convenient and high-yield synthesis for N1-tritylethane-1,1,2,2-d4-1,2-diamine, a novel mono-protected ethylenediamine-C-d4, is reported. N1-tritylethane-1,1,2,2-d4-1,2-diamine was prepared in three steps from ethylene oxide-d4 in a combined yield in the range 68-76%. Also reported is a synthesis of ethylenediamine-C-d4 in two steps from 1,2-dibromoethane-d4 in a combined yield in the range 61-65%.
PurposeCumulative radiation exposure to the hands during certain interventional procedures may be high. It is important to decrease the amount of radiation to the operator due to the possibility of deterministic effects. We performed a pilot study to demonstrate a significant decrease in operator dose when using extension tubing (ET) in combination with shielding and collimation during a simulated percutaneous transhepatic cholangiogram (PTC) procedure.MethodsA whole body, anthropomorphic phantom was used to simulate the patient. A Unfors-Xi Survey detector (to measure scatter) supported by a retort stand and trolley was placed in various positions to simulate the position of hands and eyes/thyroid of an interventionalist. Radiation dose was measured simulating left and right-sided PTC punctures with and without a lead shield, and with and without ET.ResultsRegarding the radiation dose to the hands; the use of an ET reduces dose by 54 % in right-sided PTC punctures without a shield and by 91 % if used in combination with a shield. For left-sided PTC punctures, ET reduces hand dose by 75 %. The use of collimation decreases hand dose by approximately 60 %. The use of shielding reduces dose to the eyes/thyroid by 98 %.ConclusionsThe dose to the hands can be significantly reduced with the appropriate use of a shield, ET, and tight collimation. The use of a shield is paramount to reduce dose to the eyes/thyroid. It is important for interventionalists to adhere to radiation protective practice considering the potential deterministic effects during a lifelong career.
By using poly(propylene glycol)bis(2-aminopropyl ether) (D230) as curing agent, we have prepared color-stable hydrogenated Bisphenol A (HBA) epoxy polymers, containing TiO{sub 2} nanoparticles. The loading and size of TiO{sub 2} nanoparticles (5 ~ 10, 21, 200 ~ 400 nm) are changed in order to investigate their photocatalytic effect on removing pollutants deposited on the surface of stone. HBA/D230 polymers containing different amounts of TiO{sub 2} nanomaterials were applied to methyl orange (MeO) on the limestone with exposure to the dry and wet environment, respectively. The results showed that the modification of HBA by addition of titanium dioxide particles substantially not only enhanced its protective efficiency but also rendered the treated stone surface self-cleaning ability. The photocatalytic degradation effect of MeO at the concentration of 0.001 M was the best when the size of TiO{sub 2} nanoparticles was between 200 ~ 400 nm. Compared to those in dry environment, the decrease of the content of MeO in samples exposed to wet environment was due to humidity on the surface of limestone.
The addition of beryllium to Al-Mg alloys is known to cause a dramatic decrease in oxidation; however, the mechanism behind this protective effect is not yet fully understood. To aid in finding an alternative to the toxic Be, a fundamental study of Be additions has been carried out. Industrial samples containing 2 ppm Be and a model alloy with 100 ppm Be were oxidized at temperatures between 550 °C and 750 °C in a horizontal tube furnace. The oxide layer and oxide–metal interface were investigated using SEM, FIB, and XPS. It was found that Be forms a uniform oxide layer at the oxide–metal interface which slows the diffusion of Mg and Al from the metal into the oxide layer resulting in a reduced oxidation rate and an increase in the time for breakaway oxidation to occur.
The failure behavior for two kinds of phenolic-epoxy/tetraglycidyl metaxylediamine composite coatings in 60 °C borax aqueous solution was evaluated using electrochemical methods (EIS) combined with scanning electron microscopy, confocal laser scanning microscope, water immersion test, and Raman spectrum. The main focus was on the effect of curing agent on the corrosion protection of coatings. Results revealed that the coating cured by phenolic modified aromatic amine possessed more compact cross-linked structure, better wet adhesion, lower water absorption (0.064 mg h{sup −1} cm{sup −2}) and its impedance values was closed to 10{sup 8} Ω cm{sup 2} after immersion for 576 h, while the coating cured by modified aromatic ring aliphatic amine was lower than 10{sup 5} Ω cm{sup 2}. The corrosion mechanism of the two coatings is discussed.
Tannins are polyphenols synthesized by plants and useful for the coating industry as corrosion inhibitors. In addition, lanthanum salts have a great inhibitory effect on steel corrosion. The aim of this study was to obtain lanthanum “tannate” with adequate solubility to be incorporated as the corrosion inhibitor in a wash-primer. The “tannate” was obtained from commercial “Quebracho” tannin and 0.1 M La(NO{sub 3}){sub 3}. The soluble tannin was determined by the Folin–Denis reagent, while the concentration of Lanthanum was obtained by a gravimetric procedure. The protective action of “tannate” on SAE 1010 steel was evaluated by linear polarization curves and corrosion potential measurements. Lanthanum “tannate” was incorporated in a wash-primer formulation and tested by corrosion potential and ionic resistance measurements. The corrosion rate was also determined by the polarization resistance technique. Besides, the primer was incorporated in an alkyd paint system and its anticorrosion performance assessed in the salt spray cabinet and by electrochemical impedance spectroscopy. Results showed that lanthanum “tannate” primer inhibits the development of deleterious iron oxyhydroxides on the steel substrate and incorporated into a paint system had a similar behavior to the primer formulated with zinc tetroxychromate.