Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

An elastic analysis of stresses in a uniaxially loaded sheet containing an interference-fit bolt

The stresses in a sheet with an interference-fit bolt have been calculated for two sheet-bolt interface conditions: a frictionless interface and a fixed (no-slip) interface. The stress distributions were calculated for various combinations of sheet and bolt moduli. The results show that for repeated loading the local stress range is significantly smaller if an interference bolt is used instead of a loosely fitting one. This reduction in local stress range is more pronounced when the ratio of bolt modulus to sheet modulus is large. The analysis also indicates that currently used standard values of interference cause yielding in the sheet.

Crews, J. H., Jr.↗

A stable numerical solution method in-plane loading of nonlinear viscoelastic laminated orthotropic materials

In response to the tremendous growth in the development of advanced materials, such as fiber-reinforced plastic (FRP) composite materials, a new numerical method is developed to analyze and predict the time-dependent properties of these materials. Basic concepts in viscoelasticity, laminated composites, and previous viscoelastic numerical methods are presented. A stable numerical method, called the nonlinear differential equation method (NDEM), is developed to calculate the in-plane stresses and strains over any time period for a general laminate constructed from nonlinear viscoelastic orthotropic plies. The method is implemented in an in-plane stress analysis computer program, called VCAP, to demonstrate its usefulness and to verify its accuracy. A number of actual experimental test results performed on Kevlar/epoxy composite laminates are compared to predictions calculated from the numerical method.

Gramoll, K. C.↗

Slab-geometry Nd:glass laser performance studies

It is noted that slab-geometry solid-state lasers potentially provide significant performance improvements relative to conventional rod-geometry lasers. Experimental measurements that use an Nd:glass test-bed slab laser are presented. A comparison is made between the results and computer-model predictions of the slab-geometry approach. The computer model calculates and displays the temperature and stress fields in the slab, and on the basis of these predicts birefringence and index-of-refraction distributions. The effect that these distributions have on optical propagation is determined in a polarization-sensitive ray-tracing section of the model. Calculations are also made of stress-induced surface curvature and the resulting focusing effects. The measurements are found to be in good agreement with the computer-model predictions. It is concluded that the slab configuration offers significant laser-performance advantages in comparison with the traditional rod-laser geometry.

Eggleston, J. M.↗

Investigating the Effect of Water on the Mechanical Properties of Cellulose from Multiscale Molecular Dynamics Simulations

Classical molecular dynamics (MD) simulations provide insight into the structure and physicochemical properties of materials with atomic resolution. However, the length and time scales accessible to atomistic MD are orders of magnitude smaller than many relevant processes such as the response of a bulk material to experimentally accessible strain rates, which presents challenges when comparing models to experimental measurements. Bottom-up coarse-graining provides a means for systematically mapping atomistic information to lower resolution models to increase the length and time scales achievable by simulation. Cellulose is an abundant carbohydrate biopolymer with applications to many fields of research, such as materials science and renewable energy, due to its desirable mechanical properties and viability for conversion into biofuel. The effect of moisture content on the Young's modulus of cellulose is of special interest due to its native environment often being in the hydrated secondary plant cell wall and the grinding energy requirements for biomass feedstock preprocessing. The current work investigates the effects of water solvent on the Young's modulus of cellulose calculated from coarse-grained MD mechanical stress simulations. The coarse-grained model was parametrized from atomistic MD calculations of cellulose-cellulose potentials of mean force using umbrella sampling techniques under vacuum and solvated conditions. The Young's moduli of the coarse-grained cellulose assemblies parametrized from cellulose in vacuum or solvated in water were computed via mechanical stress simulations to highlight the importance of capturing solvent interactions for modeling the mechanical behavior of cellulose.

BASIC BIOLOGICAL SCIENCES,RADIATION PROTECTION AND↗

An analysis of fiber-matrix interface failure stresses for a range of ply stress states

A graphite/bismaleimide laminate was prepared without the usual fiber treatment and was tested over a wide range of stress states to measure its ply cracking strength. These tests were conducted using off-axis flexure specimens and produced fiber-matrix interface failure data over a correspondingly wide range of interface stress states. The absence of fiber treatment, weakened the fiber-matrix interfaces and allowed these tests to be conducted at load levels that did not yield the matrix. An elastic micromechanics computer code was used to calculate the fiber-matrix interface stresses at failure. Two different fiber-array models (square and diamond) were used in these calculations to analyze the effects of fiber arrangement as well as stress state on the critical interface stresses at failure. This study showed that both fiber-array models were needed to analyze interface stresses over the range of stress states. A linear equation provided a close fit to these critical stress combinations and, thereby, provided a fiber-matrix interface failure criterion. These results suggest that prediction procedures for laminate ply cracking can be based on micromechanics stress analyses and appropriate fiber-matrix interface failure criteria. However, typical structural laminates may require elastoplastic stress analysis procedures that account for matrix yielding, especially for shear-dominated ply stress states.

Crews, J. H.↗

Can we characterize turbulence in premixed flames?

Modeling of premixed turbulent combustion involves averaging reaction rates in turbulent flows. The focus of most approaches to resolving this problem has been placed on determining the dependence of the mean rate w of product creation on the laminar flame speed S{sub L}, the rms turbulence velocity u', etc. The goal of the present work is to draw attention to another issue: May the input quantity u{sup '} for a model of w= w(u'/S{sub L},..) be considered to be known? The point is that heat release substantially affects turbulence and, hence, turbulence characteristics in premixed flames should be modeled. However, standard moment methods for numerically simulating turbulent flows do not allow us to evaluate the true turbulence characteristics in a flame. For instance, the Reynolds stresses in premixed flames are affected not only by turbulence itself, but also by velocity jump across flamelets. A common way to resolving this problem consists of considering the Reynolds stresses conditioned on unburned (or burned) mixture to be the true turbulence characteristics. In the present paper, this widely accepted but never proved hypothesis is put into question, first, by considering simple model constant-density problems (flame motion in an oscillating one-dimensional laminar flow; flame stabilized in a periodic shear, one-dimensional, laminar flow; turbulent mixing). In all the cases, the magnitude of velocity fluctuations, calculated using the conditioned Reynolds stresses, is affected by the intermittency of reactants and products and, hence, is not the true rms velocity. Second, the above claim is further supported by comparing balance equations for the mean and conditioned Reynolds stresses. The conditioned Reynolds stresses do not characterize the true turbulence in flames, because conditional averaging cuts off flow regions characterized by either high or low velocities. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermal stress fracture in elastic-brittle materials

The reported investigation shows that the assessment of the possibility of the thermal fracture of brittle materials depends upon an accurate evaluation of the thermal stresses and the determination of the resulting stress intensity factors. The stress intensity factors can be calculated in a variety of ways ranging from the very precise to approximate, but only for a limited number of geometries. The main difficulty is related to the determination of the thermal stress field because of its unusual character and its dependence upon boundary conditions at points far from the region of thermal activity. Examination of a number of examples suggests that the best visualization of the thermal stresses and any associated fracture can be made by considering the problem to be the combination of thermal and isothermal problems or by considering that the prime effect of the temperature is in the generation of thermal strains and that the thermal stresses are simply the result of the region trying to accommodate these strains.

Emery, A. F.↗

Stress analysis and stress intensity factors for finite geometry solids containing rectangular surface cracks

The line method of analysis is applied to the Navier-Cauchy equations of elastic equilibrium to calculate the displacement field in a finite geometry bar containing a variable depth rectangular surface crack under extensionally applied uniform loading. The application of this method to these equations leads to coupled sets of simultaneous ordinary differential equations whose solutions are obtained along sets of lines in a discretized region. Using the obtained displacement field, normal stresses and the stress intensity factor variation along the crack periphery are calculated for different crack depth to bar thickness ratios. Crack opening displacements and stress intensity factors are also obtained for a through-thickness, center cracked bar with variable thickness. The reported results show a considerable potential for using this method in calculating stress intensity factors for commonly encountered surface crack geometries in finite solids.

Gyekenyesi, J. P.↗

Predicting Hydraulic Fracture Trajectory Under the Influence of a Mine Drift in EGS Collab Experiment I

Experiment I of the EGS Collab project entails drilling largely horizontal wellbores in phyllite of the Precambrian Poorman formation, at the Sanford Underground Research Facility (SURF), located at the former Homestake Gold Mine, in Lead, South Dakota, and creating/stimulating hydraulic fractures from one of the wellbores. The stimulation well was drilled from the old mine drift at the 4850 level (4850 feet deep from ground surface) along the minimum in situ principal stress direction and the fracture initiation point is approximately 40 m from the drift. An essential component of the experiment design is to predict the trajectory of the hydraulic fractures so that the production and monitoring wells can be drilled accordingly and precautionary measures can be taken to prevent the fracture from intersecting the drift. Through thermo-hydro-mechanical (THM) coupled simulation of the cooling and drainage history experienced by the drift, we calculate the temperature, pore pressure, and stress distributions around the drift. The calculated temperature is validated against measurements along existing vertical wells. The simulation results suggest that the cooling of the rock around the drift has caused very significant thermal stress with magnitudes up to several MPas near the fracture initiation point. The minimum principal stress decreases rapidly from this point toward the drift. A fully coupled hydraulic fracturing simulation indicates that the fracture would have a strong tendency to propagate toward the drift, driven by the radial gradient of the minimum principal stress. The fracture will remain planar until it curves and becomes parallel to the drift when the fracture front is a few meters from the drift. The role of these simulation results is twofold in the EGS Collab experiment: they guide experiment designs and will be used to validate the simulation codes against the actual experiment results.

Hydraulic fracturing, enhanced geothermal system, ↗

Brazil disc Testing of LX-17-1

When considering alternate test methods for assessing the tensile performance of insensitive plastic bonded explosive (PBX) materials, Brazil disc tensile testing is attractive from several standpoints. First, compared to the traditional dog-bone shaped specimen normally used in the direct tensile test, the Brazil test specimen is considerably easier to produce. Second, the Brazil specimen is compact, with a low aspect ratio that allows it to be machined from a wide variety of pressed geometries. Assuming test results are consistent and interpretable, the method could open up possibilities for rapid assessment of ultimate tensile strengths, and might be especially attractive when a large number of samples are to be tested. The trade-off for specimen simplicity is, however, that interpretation of the results from Brazil tests is inherently far less intuitive, and more difficult, than is the case with traditional tensile testing, since the method involves complex stress loading. As a result, the derivation of what one hopes are equivalent tensile failure stresses from Brazil testing necessitates some fairly involved calculations, requiring parameters that are not always readily obtained. In addition to some significant uncertainties, the specimen geometry does not lend itself easily to the accommodation of traditional strain measurement devices such as extensometers. As a consequence, optical techniques such as digital image correlation (DIC) are preferred when stress-strain curves are needed. In this test series we performed a sequence of experiments using Brazil discs made from LX-17-1. Tests were performed on samples at two different scaled sizes: discs that were 0.5 inches in diameter and 0.25 inch thick, and discs that were 1 inch in diameter and a 0.5 inch thick. Each of the specimen sets was tested using matching, equivalently scaled test fixtures, each with anvils whose radii were 0.25% greater than their respective specimen radii. All specimens tested were machined from billet pressed material made from Holston #851009 (LLNL tag #C-329) LX-17-1 molding powder. Tests were performed at two temperatures, +23 °C and +50 °C, with three each test redundancies at each condition. Based on data from this set of experiments we hoped to provide preliminary answers to a number of questions, including: 1) Roughly, what is the level of scatter in the data? 2) Are results scale independent, at least within the limited range of specimen sizes tested? 3) Using a consistent set of parameters, can we use the equations given by Sato and Awaji1 to calculate peak tensile stresses that are nearly equivalent to those measured using traditional dog-bone tensile testing methods.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Prediction of directional reflectance of a corn field under stress

A vegetative canopy model concept is developed and used to calculate the directional spectral reflectance of a corn field under stress. The problem has been idealized by assuming that the canopy is represented in several layers of uniform but randomly distributed biological components; horizontal and vertical projection of leaves, for example, replaces the actual leaf. An accumulative horizontal projection leads to a quantitative horizontal leaf area index while accumulated vertical projections provide the vertical leaf index area for each layer. The spectral properties of the projections are obtained from the spectral properties of the biological components. These techniques together with soil reflectance data provide a physical description for the vegetative canopy and adequately interprete multispectral scanning data.

Suits, G. H.↗

Fracture Mechanics of Thin, Cracked Plates Under Tension, Bending and Out-of-Plane Shear Loading

Cracks in the skin of aircraft fuselages or other shell structures can be subjected to very complex stress states, resulting in mixed-mode fracture conditions. For example, a crack running along a stringer in a pressurized fuselage will be subject to the usual in-plane tension stresses (Mode-I) along with out-of-plane tearing stresses (Mode-III like). Crack growth and initiation in this case is correlated not only with the tensile or Mode-I stress intensity factor, K(sub I), but depends on a combination of parameters and on the history of crack growth. The stresses at the tip of a crack in a plate or shell are typically described in terms of either the small deflection Kirchhoff plate theory. However, real applications involve large deflections. We show, using the von-Karman theory, that the crack tip stress field derived on the basis of the small deflection theory is still valid for large deflections. We then give examples demonstrating the exact calculation of energy release rates and stress intensity factors for cracked plates loaded to large deflections. The crack tip fields calculated using the plate theories are an approximation to the actual three dimensional fields. Using three dimensional finite element analyses we have explored the relationship between the three dimensional elasticity theory and two dimensional plate theory results. The results show that for out-of-plane shear loading the three dimensional and Kirchhoff theory results coincide at distance greater than h/2 from the crack tip, where h/2 is the plate thickness. Inside this region, the distribution of stresses through the thickness can be very different from the plate theory predictions. We have also explored how the energy release rate varies as a function of crack length to plate thickness using the different theories. This is important in the implementation of fracture prediction methods using finite element analysis. Our experiments show that under certain conditions, during fatigue crack growth, the presence of out-of-plane shear loads induces a great deal of contact and friction on the crack surfaces, dramatically reducing crack growth rate. A series of experiments and a proposed computational approach for accounting for the friction is discussed.

Zehnder, Alan T.↗

Phase transitions and 2D spherical convection in a large icy satellite

Three ice phase transitions, based on experimental and theoretical results, were incorporated into a 2D spherical convection model. These phase transitions are the exothermic Ice 1-2, the endothermic Ice 2-6, and the exothermic Ice 6-8 phase transitions. The fluid is assumed isoviscous and the anelastic liquid formulation was used. The object is an icy satellite whose physical characteristics resemble those of Ganymede or Callisto. Structural models, similar to those of Mueller and McKinnon, with different core sizes, i.e. with different degree of differentiation were studied. The shells, i.e. the mantle of the satellite, is heated both internally and from below to account for the decaying radiogenic heating and the heat flow from the solid core. The lower boundary of the mantle is rigid and isothermal, the upper boundary is isothermal. Calculations with rigid and shear stress free upper boundary are carried out in order to assess the role of the different boundary conditions. Two different Rayleigh numbers, depending on the assumed value of the viscosity, were used in the calculations and the thermal evolution of the satellite was studied. The suit of calculations presented demonstrates that phase transition cannot be ignored when the thermal evolution of a large icy satellite has to be studied. The importance of the construction of the realistic phase diagram for ice was also documented. On the other hand the degree of differentiation, simulated with the structures with different core's radius does not seem to drastically influence the overall behavior of the convective activity. Within the limits of our simulations, the post-accretional evolution seems to be independent on the degree of primordial differentiation.

Forni, O.↗

Structural Design and Aeromechanical Analysis of Unconventional Blades for Future Mars Rotorcraft

The structural design for rotor blades with thin, unconventional airfoils for Earth-based testing is obtained using three-Dimensional (3D) aeromechanical analysis in support of the NASA ROAMX project. The outer mold line was provided by NASA, but the internal structural design was developed at the University of Maryland and is presented here along with a thorough aeromechanical analysis. The main objectives are to verify the structural integrity of the design and understand the unique aeroelastic behavior of the non-conventional airfoils designed for low-Reynolds number and high subsonic Mach number. Four different blade models are considered, with the pitch axis varied from quarter-chord to mid-chord to determine the effect of C.G. offset on natural frequencies, blade deformations, root loads, and 3D stresses. First, torsional stability is calculated for each of the designs – especially important due to the low Lock number on Mars. All four blade designs are studied under rotation in vacuum, and significant reductions in root loads and 3D stresses are achieved by moving the pitch axis closer to mid-chord to reduce the C.G. offset. Based on the vacuum analysis, the blade design with the pitch axis at 40% chord is selected for aeromechanical analysis. The blade control load, airloads, deformations, and 3D stresses are studied for steady hover. Dynamic control load and dynamic 3D stresses are studied for unsteady hover achieved using cyclic. Significant elastic twist is observed due to the trapeze effect and propeller moment, affecting the spanwise distribution of aerodynamic loads on the blades. The dynamic control load is found to increase significantly due to inertial coupling from the C.G. offset. The dynamic stresses also increase, although still have factors of safety greater than two for both tensile and compressive stress.

Structural Design↗

Fracture of composite panels

The fracture problem in panels consisting of periodically arranged load carrying and buffer strips of different materials is considered. The main emphasis is placed on the problem of a crack terminating at and crossing the interfaces and on the stress free end problem. The problem is formulated in terms of a system of singular integral equations, and numerical solutions are obtained for certain material combinations. With the study of possible crack propagation and delamination in mind, certain stress intensity factors are defined and calculated. A main result is that when the crack touches or intersects a bimaterial interface, the stress state has no longer the standard square root singularity, and, to study further propagation of the crack, the conventional fracture models need to be modified, or new models need to be developed.

Erdogan, F.↗

Effect of mesh distortion on the accuracy of transverse shear stresses and their sensitivity coefficients in multilayered composites

A study is made of the effect of mesh distortion on the accuracy of transverse shear stresses and their first-order and second-order sensitivity coefficients in multilayered composite panels subjected to mechanical and thermal loads. The panels are discretized by using a two-field degenerate solid element, with the fundamental unknowns consisting of both displacement and strain components, and the displacement components having a linear variation throughout the thickness of the laminate. A two-step computational procedure is used for evaluating the transverse shear stresses. In the first step, the in-plane stresses in the different layers are calculated at the numerical quadrature points for each element. In the second step, the transverse shear stresses are evaluated by using piecewise integration, in the thickness direction, of the three-dimensional equilibrium equations. The same procedure is used for evaluating the sensitivity coefficients of transverse shear stresses. Numerical results are presented showing no noticeable degradation in the accuracy of the in-plane stresses and their sensitivity coefficients with mesh distortion. However, such degradation is observed for the transverse shear stresses and their sensitivity coefficients. The standard of comparison is taken to be the exact solution of the three-dimensional thermoelasticity equations of the panel.

Noor, Ahmed K.↗

Stress reduction of Cu-doped diamond-like carbon films from ab initio calculations

Structure and properties of Cu-doped diamond-like carbon films (DLC) were investigated using ab initio calculations. The effect of Cu concentrations (1.56∼7.81 at.%) on atomic bond structure was mainly analyzed to clarify the residual stress reduction mechanism. Results showed that with introducing Cu into DLC films, the residual compressive stress decreased firstly and then increased for each case with the obvious deterioration of mechanical properties, which was in agreement with the experimental results. Structural analysis revealed that the weak Cu-C bond and the relaxation of both the distorted bond angles and bond lengths accounted for the significant reduction of residual compressive stress, while at the higher Cu concentration the increase of residual stress attributed to the existence of distorted Cu-C structures and the increased fraction of distorted C-C bond lengths.

36 MATERIALS SCIENCE↗

Modeling of Martensite Transformation in White Layer under Thermo-mechanical Coupling in Hard-Cutting Process

Martensite volume fraction determines the hardness and wear resistance of workpiece, predicting the martensite volume fraction of the white layer is of great significance for improving the surface quality of the workpiece. Accordingly, a theoretical model on the martensite volume fraction was developed in combination with the martensite transformation temperature model and the hard-cutting FE model. A finite element (FE) model of the hard-cutting was established to obtain the stress distribution of the workpieces. A calculation model of martensite phase transformation temperature M{sub S} under the influence of the cooling rate and stress was deduced based on the change of Gibbs free energy. A theoretical model of martensite volume fraction f{sub M} of the white layer was developed based on the M{sub S} and the FE simulations. The f{sub M} calculated by the theoretical model is in accordance with the experimental result. The effects of cutting speed, feed rate, flank wear and tool rake angle on the f{sub M} in the white layers were predicted and analyzed; the results show that the f{sub M} decreases first and then increases with the cutting speed, decreases with the feed rate and the flank wear, and increases with the tool rake angle.

36 MATERIALS SCIENCE↗