Search NASA⌕ Search

SEARCH · Search NASA

Results for “design space approximation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Shower disc sampling and the angular resolution of gamma-ray shower detectors

As part of the design study for the new UHE gamma ray detector being constsructed at Haverah Park, a series of experiments using scintillators operated side-by-side in 10 to the 15th power eV air showers are undertaken. Investigation of the rms sampling fluctuations in the shower disc arrival time yields an upper limit to the intrinsic sampling uncertainty, sigma sub rms = (1.1 + or - 0.1)ns, implying an angular resolution capability 1 deg for an inter-detector spacing of approximately 25 m.

Lambert, A.↗

The 250AH/90A active lithium-thionyl chloride cell for Centaur-G application

A high rate active Li/SOCl2 cell was designed for use in a 28 volt, 250 amp-hour space battery system. The lithium battery is being considered as a replacement of its heavier silver-zinc counterpart on board the Centaur-G booster rocket which is used to launch payloads from the Space Shuttle cargo bay into deep-space. Basically a feasibility study, this development effort is demonstrating the ability of the lithium cell to deliver up to 90 amps safely at power densities of approximately 25 watts per pound. Test data on 4 prototype units is showing an energy density of 85 watt-hours per pound and 9.0 watt-hours/cu in. The cells tested typically delivered 280 to 300 amp-hours under ambient temperature test conditions using alternating continuous loads of 90, 55, and 20 amperes throughout life. Data from four cells tested are presented to demonstrate the capability of Li/SOCl2 technology for a C/3 discharge rate in active and hermetic cell units.

Zolla, A. E.↗

Preliminary investigation of stability of a fin-stiffened slender strut

A fin-stiffened strut concept which possesses high bending stiffness and low packaged volume has been identified for use on large space structures. The concept incorporates three curved fins which deploy from a core tube to increase the effective cross-sectional moment of inertia, the buckling load, and the vibration frequency of the strut. A strut design incorporating welded fin connections provides an upper bound of the strut buckling load. A strut design which allows the individual fins and core to move independently in the strut axial direction provides a lower bound of the strut buckling load which is approximately 20 to 25 percent of the upper bound. A practical strut design, incorporating hinge assemblies which constrain the fins to move together but independently of the core tube in the strut axial direction, provides a buckling load which is 75 to 80 percent of the upper bound. Euler's equation can be used to accurately predict buckling loads for the bounding designs. Flat plate finite element models of all designs give results that agree to within 10 percent of the experimental values. Equivalent beam models of the strut give results which are slightly less accurate.

Lake, Mark S.↗

Luminance-model-based DCT quantization for color image compression

A model is developed to approximate visibility thresholds for discrete cosine transform (DCT) coefficient quantization error based on the peak-to-peak luminance of the error image. Experimentally measured visibility thresholds for R, G, and B DCT basis functions can be predicted by a simple luminance-based detection model. This model allows DCT coefficient quantization matrices to be designed for display conditions other than those of the experimental measurements: other display luminances, other veiling luminances, and other spatial frequencies (different pixel spacings, viewing distances, and aspect ratios).

Ahumada, Albert J., Jr.↗

Digital modelling, ideal state reconstructor, and control for time-delay sampled-data systems

The cascaded discrete-time state-space representation of a cascaded continuous-time system with fractional input delays is established. Based on the time-delay digital modelling, a practically implementable ideal state reconstructor is also established such that system states are exactly reconstructed via the measurement histories of inputs and outputs without a state observer. By utilizing the blockpulse function approximation the digital modelling of cascaded continuous-time systems with fractional input delays can be carried out, and an artificial input design method is proposed to determine the state feedback gain. Thus the practically implementable digital control law can be established for digital control of time-delay sampled-data systems. An illustrative example is shown to demonstrate the effectiveness of the proposed method.

Tsai, J. S. H.↗

JWST Mirror Technology Development

Since the initial Design Studies leading to JWST, Mirror Technology was identified as a (if not the) critical capability necessary to enable the next generation of large aperture space telescopes required to achieve the science goals of imaging the earliest galaxies and proto-galaxies after the big bang. Specific telescope architectures were explored via three independent design concept studies conducted during the summer of 1996. Achieving the desired science objectives required a never before demonstrated space telescope capability, one with an 8 meter class primary mirror that is diffraction limited at 2 micrometers and operating in deep space at temperatures well below 70K. Beryllium was identified in the NASA "Yardstick" design as the preferred material because of its ability to provide stable optical performance in the anticipated thermal environment as well as its excellent specific stiffness. Because of launch vehicle constraints, two very significant architectural constraints were placed upon the telescope: segmentation and areal density. Each of these directly resulted in specific technology capability requirements. First, because the maximum launch vehicle payload fairing diameter is approximately 4.5 meters, the only way to launch an 8 meter class mirror is to segment it, fold it and deploy it on orbit - resulting in actuation and control requirements. Second, because of launch vehicle mass limits, the primary mirror allocation was only 1000 kg - resulting in a maximum areal density specification of 20 kilograms per square meter.

Stahl, H. Philip↗

Launching a dream: A teachers guide to a simulated space shuttle mission

Two simulated shuttle missions cosponsored by the NASA Lewis Research Center and Cleveland, Ohio, area schools are highlighted in this manual for teachers. A simulated space shuttle mission is an opportunity for students of all ages to plan, train for, and conduct a shuttle mission. Some students are selected to be astronauts, flight planners, and flight controllers. Other students build and test the experiments that the astronauts will conduct. Some set up mission control, while others design the mission patch. Students also serve as security officers or carry out public relations activities. For the simulated shuttle mission, school buses or recreation vehicles are converted to represent shuttle orbiters. All aspects of a shuttle mission are included. During preflight activities the shuttle is prepared, and experiments and a flight plan are made ready for launch day. The flight itself includes lifting off, conducting experiments on orbit, and rendezvousing with the crew from the sister school. After landing back at the home school, the student astronauts are debriefed and hold press conferences. The astronauts celebrate their successful missions with their fellow students at school and with the community at an evening postflight recognition program. To date, approximately 6,000 students have been involved in simulated shuttle missions with the Lewis Research Center. A list of participating schools, along with the names of their space shuttles, is included. Educations outcomes and other positive effects for the students are described.

Source record↗

Automation & Autonomy Standards and Guidelines for Space Vehicles

The NASA Office of the Chief Health and Medical Officer (OCHMO) requested HRP conduct a survey of industry and government standards and guidelines for the interaction of automation/autonomy with humans. Guidance for verification testing of human-automation designs was also requested. A rapid response was requested so that the deliverables could be provided as part of a future NASA solicitation for automated systems for HLS. The project began with a broad review and analysis of prior NASA work in this area, as well as external standards related to human interaction with automation/autonomy. The team reviewed approximately 200 documents, and interviewed multiple industry and government subject matter experts (SMEs). “Gold standard” documents were selected for focus and key categories were identified. A cross-walk of standards was created, and common standards and guidelines were selected and rephrased (where necessary) to be information-rich, concise, and usable. Verification guidelines and examples were also developed. The final report includes an introduction to automation and autonomy, selected standards and guidelines, verification method guidance, and research gaps. In addition to the report, the team delivered a list of candidate standards for autonomous vehicles, as well as a list of candidate standards for a future NASA-STD-3001 update on automation/autonomy. The presentation will describe the rapid response project approach and methods, examples of standards and guidelines identified and delivered to OCHMO, and research needed to develop additional automation/autonomy design guidance where gaps currently exist.

automation↗

Coupling Visualization, Simulation, and Deep Learning for Ensemble Steering of Complex Energy Models

We describe a new framework that allows users to explore and steer ensembles of energy systems simulations by coupling multiple energy models and interactive visualization through a dataflow API. Through the visual interface, users can interactively explore complex parameter spaces populated by hundreds, or thousands, of simulation runs and interactively spawn new simulations to 'fill in' regions of interest in the parameter space. The computational and visualization capabilities reside within a general-purpose dataflow architecture for connecting producers of multidimensional timeseries data, such as energy simulations, with consumers of that data, whether they be visualizations, statistical analyses, or datastores. Fast computation and agile dataflow can enhance the engagement with energy simulations, allowing users to populate the parameter space in real time. However, many energy simulations are far too slow to provide an interactive response. To support interactive feedback, we are creating reduced-form simulations developed through machine learning techniques, which provide statistically sound estimates of the results of the full simulations at a fraction of the computational cost. These reduced-form simulations have response times on the order of seconds, suitable for real-time human-in-the-loop design and analysis. The approximation methods apply to a wide range of computational models, including supply-chain models, electric power grid simulations, and building models. Such reduced-form representations do not replace or re-implement existing simulations, but instead supplement them by enabling rapid scenario design and exploration for large ensembles of simulations. The improved understanding, facilitated by the reduced-form models, dataflow API, and visualization tools, allows researchers to better allocate computational resources to capture informative relationships within the system as well as provide a low-cost method for validating and quality-checking large-scale modeling efforts.

97 MATHEMATICS AND COMPUTING↗

Space vehicle meteoroid shielding design

Design principles of spaced, multiwall meteoroid protection are investigated in the light of experimental data generated during the Apollo Program. The outer wall or shield is shown to be the most important element in the meteoroid-spacecraft interaction. The condition of the debris is primarily a function of the shock pressure, the melting points of the meteoroid and the shield, and the length of the meteoroid and thickness of the shield. Spacing between the walls is effective up to approximately 100 times the length of the meteoroid. The required thickness of the second wall is shown to be proportional to the meteoroid mass, velocity, and density, and to the spacing between the walls, taken with exponents dependent upon the condition of the debris. The effects of placing additional elements (insulation or honeycomb cells) between the two walls are discussed, and the efficiency of various protective configurations is presented. An analysis of the meteoroid protection proposed for the Comet Halley probe is included as an appendix.

Cour-Palais, B. G.↗

Spectroscopic method for Earth-satellite-Earth laser long-path absorption measurements using Retroreflector In Space (RIS)

The Retroreflector in Space (RIS) is a single element cube-corner retroreflector with a diameter of 0.5 m designed for earth-satellite-earth laser long-path absorption experiments. The RIS is to be loaded on the Advanced Earth Observing System (ADEOS) satellite which is scheduled for launch in Feb. 1996. The orbit for ADEOS is a sun synchronous subrecurrent polar-orbit with an inclination of 98.6 deg. It has a period of 101 minutes and an altitude of approximately 800 km. The local time at descending node is 10:15-10:45, and the recurrent period is 41 days. The velocity relative to the ground is approximately 7 km/s. In the RIS experiment, a laser beam transmitted from a ground station is reflected by RIS and received at the ground station. The absorption of the intervening atmosphere is measured in the round-trip optical path.

Sugimoto, Nobuo↗

Design Challenges of Power Systems for Instrumented Spacecraft with Very Low Perigees in the Earth's Ionosphere

Designing a solar array to power a spacecraft bus supporting a set of instruments making in situ plasma and neutral atmosphere measurements in the ionosphere at altitudes of 120km or lower poses several challenges. The driving scientific requirements are the field-of-view constraints of the instruments resulting in a three-axis stabilized spacecraft, the need for an electromagnetically unperturbed environment accomplished by designing an electrostatically conducting solar array surface to avoid large potentials, making the spacecraft body as small and as symmetric as possible, and body-mounting the solar array. Furthermore, the life and thermal constraints, in the midst of the effects of the dense atmosphere at low altitude, drive the cross-sectional area of the spacecraft to be small particularly normal to the ram direction. Widely varying sun angles and eclipse durations add further complications, as does the growing desire for multiple spacecraft to resolve spatial and temporal variations packaged into a single launch vehicle. Novel approaches to insure adequate orbit-averaged power levels of approximately 250W include an oval-shaped cross section to increase the solar array collecting area during noon-midnight orbits and the use of a flywheel energy storage system. The flywheel could also be used to help maintain the spacecraft's attitude, particularly during excursions to the lowest perigee altitudes. This paper discusses the approaches used in conceptual power designs for both the proposed Dipper and the Global Electrodynamics Connections (GEC) Mission currently being studied at the NASA/Goddard Space Flight Center.

Moran, Vickie Eakin↗

An Approximate Solution and Master Curves for Buckling of Symmetrically Laminated Composite Cylinders

Nondimensional linear-bifurcation buckling equations for balanced, symmetrically laminated cylinders with negligible shell-wall anisotropies and subjected to uniform axial compression loads are presented. These equations are solved exactly for the practical case of simply supported ends. Nondimensional quantities are used to characterize the buckling behavior that consist of a stiffness-weighted length-to-radius parameter, a stiffness-weighted shell-thinness parameter, a shell-wall nonhomogeneity parameter, two orthotropy parameters, and a nondimensional buckling load. Ranges for the nondimensional parameters are established that encompass a wide range of laminated-wall constructions and numerous generic plots of nondimensional buckling load versus a stiffness-weighted length-to-radius ratio are presented for various combinations of the other parameters. These plots are expected to include many practical cases of interest to designers. Additionally, these plots show how the parameter values affect the distribution and size of the festoons forming each response curve and how they affect the attenuation of each response curve to the corresponding solution for an infinitely long cylinder. To aid in preliminary design studies, approximate formulas for the nondimensional buckling load are derived, and validated against the corresponding exact solution, that give the attenuated buckling response of an infinitely long cylinder in terms of the nondimensional parameters presented herein. A relatively small number of "master curves" are identified that give a nondimensional measure of the buckling load of an infinitely long cylinder as a function of the orthotropy and wall inhomogeneity parameters. These curves reduce greatly the complexity of the design-variable space as compared to representations that use dimensional quantities as design variables. As a result of their inherent simplicity, these master curves are anticipated to be useful in the ongoing development of buckling-design technology.

Nemeth, Michael P.↗

Domain-Specific Languages and Diagram Customization for a Concurrent Engineering Environment

A major open question for advocates of Model-Based Systems Engineering (MBSE) is the question of how system and subsystem engineers will work together. The Systems Modeling Language (SysML), like any language intended for a large audience, is in tension between the desires for simplicity and for expressiveness. In order to be more expressive, many specialized language elements may be introduced, which will unfortunately make a complete understanding of the language a more daunting task. While this may be acceptable for systems modelers, it will increase the challenge of including subsystem engineers in the modeling effort. One possible answer to this situation is the use of Domain-Specific Languages (DSL), which are fully supported by the Unified Modeling Language (UML). SysML is in fact a DSL for systems engineering. The expressive power of a DSL can be enhanced through the use of diagram customization. Various domains have already developed their own schematic vocabularies. Within the space engineering community, two excellent examples are the propulsion and telecommunication subsystems. A return to simple box-and-line diagrams (e.g., the SysML Internal Block Diagram) are in many ways a step backward. In order allow subsystem engineers to contribute directly to the model, it is necessary to make a system modeling tool at least approximate in accessibility to drawing tools like Microsoft PowerPoint and Visio. The challenge is made more extreme in a concurrent engineering environment, where designs must often be drafted in an hour or two. In the case of the Jet Propulsion Laboratory's Team X concurrent design team, a subsystem is specified using a combination of PowerPoint for drawing and Excel for calculation. A pilot has been undertaken in order to meld the drawing portion and the production of master equipment lists (MELs) via a SysML authoring tool, MagicDraw. Team X currently interacts with its customers in a process of sharing presentations. There are several inefficiencies that arise from this situation. The first is that a customer team must wait two weeks to a month (which is 2-4 times the duration of most Team X studies themselves) for a finalized, detailed design description. Another is that this information must be re-entered by hand into the set of engineering artifacts and design tools that the mission concept team uses after a study is complete. Further, there is no persistent connection to Team X or institutionally shared formulation design tools and data after a given study, again reducing the direct reuse of designs created in a Team X study. This paper presents the underpinnings of subsystem DSLs as they were developed for this pilot. This includes specialized semantics for different domains as well as the process by which major categories of objects were derived in support of defining the DSLs. The feedback given to us by the domain experts on usability, along with a pilot study with the partial inclusion of these tools is also discussed.

Cole, Bjorn↗

SL-1 Accident Briefing Report - 1961 Nuclear Reactor Meltdown Educational Documentary

U.S. Atomic Energy Commission (Idaho Operations Office) briefing about the SL-1 Nuclear Reactor Meltdown. The SL-1, or Stationary Low-Power Reactor Number One, was a United States Army experimental nuclear power reactor which underwent a steam explosion and meltdown on January 3, 1961, killing its three operators. The direct cause was the improper withdrawal of the central control rod, responsible for absorbing neutrons in the reactor core. The event is the only known fatal reactor accident in the United States. The accident released about 80 curies (3.0 TBq) of Iodine-131, which was not considered significant due to its location in a remote desert of Idaho. About 1,100 curies (41 TBq) of fission products were released into the atmosphere. The facility, located at the National Reactor Testing Station approximately 40 miles (64 km) west of Idaho Falls, Idaho, was part of the Army Nuclear Power Program and was known as the Argonne Low Power Reactor (ALPR) during its design and build phase. It was intended to provide electrical power and heat for small, remote military facilities, such as radar sites near the Arctic Circle, and those in the DEW Line. The design power was 3 MW (thermal). Operating power was 200 kW electrical and 400 kW thermal for space heating. In the accident, the core power level reached nearly 20 GW in just four milliseconds, precipitating the reactor accident and steam explosion.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Load and dynamic assessment of B-52B-008 carrier aircraft for finned configuration 1 space shuttle solid rocket booster decelerator subsystem drop test vehicle. Volume 3: Pylon load data method 1

The pylon loading at the drop test vehicle and wing interface attach points is presented. The loads shown are determined using a stiffness method, which assumes the side stiffness of the foreward hook guide to be one-fourth of the fore and aft stiffness of each drag pin. The net effect of this assumption is that the forward hook guide reacts approximately 85% of the drop test vehicle yawing moment. For a comparison of these loads to previous X-15 analysis design loadings, see Volume 1 of this document.

Quade, D. A.↗

Chaotic mixing in a planar, curved channel using periodic slip

We propose a novel strategy for designing chaotic micromixers using curved channels confined between two flat planes. The location of the separatrix between the Dean vortices, induced by centrifugal forces, is dependent on the location of the maxima of axial velocity. An asymmetry in the axial velocity profile can change the location of the separatrix. This is achieved physically by introducing slip alternatingly at the top and bottom walls. This leads to streamline crossing and Lagrangian chaos. An approximate analytical solution of the velocity field is obtained using perturbation theory. This is used to find the Lagrangian trajectories of fluid particles. Poincare sections taken at periodic locations in the axial direction are used to study the extent of chaos. We study two microchannel designs, called circlet and serpentine, in which the Dean vortices in adjacent half cells are co-rotating and counter-rotating, respectively. The extent of mixing, at low Re and low slip length, is shown to be greater in the serpentine case. Wide channels are observed to have much better mixing than tall channels; an important observation not made for separatrix flows till now. Eulerian indicators are used to gauge the extent of mixing, with varying slip length, and it is shown that an optimum slip length exists which maximizes the mixing in a particular geometry. Once the parameter space of relatively high mixing is identified, detailed variance computations are carried out to identify the detailed features.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A two-and-a-half dimensional symplectic space-charge solver

The nonlinear space-charge effect plays a significant role in high-intensity accelerators and has been extensively studied using multi-particle tracking methods. In this paper, we present a novel 2.5- dimensional symplectic space-charge solver specifically designed for long beam bunches. We begin by detailing its application to a transverse Gaussian density distribution under open boundary conditions in a straight system, where a semi-analytical expression is derived. We then demonstrate the solver’s adaptation to arbitrary distributions in open space, as well as within rectangular and round conducting pipes. Finally, we discuss the extension of this solver to circular accelerator systems. This study shows that the fast 2.5-dimensional solver can be a good approximation to the fully three-dimensional solver for long bunches in large circular accelerators.

Beam code development & simulation techniques↗