Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Analysis of stress corrosion cracking in alloy 718 following commercial reactor exposure

Alloy 718 is generally considered a highly corrosion-resistant material but can still be susceptible to stress corrosion cracking (SCC). The combination of factors leading to SCC susceptibility in the alloy is not always clear enough. In this paper, alloy 718 leaf spring (LS) materials that suffered stress corrosion damage during two 24-month cycles in pressurized water reactor service, operated to >45 MWd/mtU burn-up, was investigated. Compared to archival samples fabricated through the same processing conditions, little microstructural and property changes occurred in the material with in-service irradiation, contrary to high dose rate laboratory-based experiments reported in literature. Though the lack of delta phase formation along grain boundaries would suggest a more SCC resistant microstructure, grain boundary cracking in the material was extensive. Crack propagation routes were explored through focused ion beam milling of specimens near the crack tip for transmission electron microscopy as well as in polished plan view and cross-sectional samples for electron backscatter diffraction analysis. It has been shown in this study that cracks propagated mainly along random high-angle grain boundaries, with the material around cracks displaying a high local density of dislocations. The slip lines were produced through the local deformation of the leaf spring material above their yield strength. Also, the cause for local SCC appears to be related to oxidation of both slip lines and grain boundaries, which under the high in-service stresses resulted in crack development in the material.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Monte Carlo modeling of recrystallization processes in α-uranium

In this study, starting with electron backscattered diffraction (EBSD) data obtained from a warm clock-rolled α-uranium deformation microstructure, a Potts Monte Carlo model was used to simulate static site-saturated recrystallization while testing a number of different conditions for the assignment of recrystallized nuclei within the microstructure. The simulations support observations that recrystallized nuclei within α-uranium form preferentially on non-twin high-angle grain boundary sites at 450 °C, and demonstrate that the most likely nucleation sites on these boundaries can be identified by the surrounding degree of Kernel Average Misorientation (KAM), which may be considered as a proxy for the local geometrically necessary dislocation (GND) density.

36 MATERIALS SCIENCE↗

Microstructural evolution of neutron-irradiated T91 and NF616 to ~4.3 dpa at 469 °C

Ferritic-martensitic steels such as T91 and NF616 are candidate materials for several nuclear applications. Here, this study evaluates radiation resistance of T91 and NF616 by examining their microstructural evolutions and hardening after the samples were irradiated in the Advanced Test Reactor to ~4.3 displacements per atom (dpa) at an as-run temperature of 469 °C. In general, this irradiation did not result in significant difference in the radiation-induced microstructures between the two steels. Compared to NF616, T91 had a higher number density of dislocation loops and a lower level of radiation-induced segregation, together with a slightly higher radiation-hardening. Unlike dislocation loops developed in both steels, radiation-induced cavities were only observed in T91 but remained small with sub-10 nm sizes. Lastly, other than the relatively stable M 23 C 6 , a new phase (likely Sigma phase) was observed in T91 and radiation-enhanced MX → Z phase transformation was identified in NF616. Laves phase was not observed in the samples.

36 MATERIALS SCIENCE↗

Predicting neutron damage using TEM with in situ ion irradiation and computer modeling

We have constructed a computer model of irradiation defect production closely coordinated with TEM and in situ ion irradiation of Molybdenum at 80 degrees C over a range of dose, dose rate and foil thickness. We have reexamined our previous ion irradiation data to assign appropriate error and uncertainty based on more recent work. The spatially dependent cascade cluster dynamics model is updated with recent Molecular Dynamics results for cascades in Mo. After a careful assignment of both ion and neutron irradiation dose values in dpa, TEM data are compared for both ion and neutron irradiated Mo from the same source material. Using the computer model of defect formation and evolution based on the in situ ion irradiation of thin foils, the defect microstructure, consisting of densities and sizes of dislocation loops, is predicted for neutron irradiation of bulk material at 80 degrees C and compared with experiment. Reasonable agreement between model prediction and experimental data demonstrates a promising direction in understanding and predicting neutron damage using a closely coordinated program of in situ ion irradiation experiment and computer simulation.

42 ENGINEERING↗

Irradiation effects in high entropy alloys and 316H stainless steel at 300 °C

High entropy alloys (HEAs) have been considered for applications in nuclear reactors due to their promising mechanical properties, corrosion and radiation resistance. It has been suggested that sluggish diffusion kinetics and lattice distortion of HEAs can enhance the annihilation of irradiation-induced defects, giving rise to a higher degree of tolerance to irradiation damage. In order to understand the irradiation effects in HEAs and to demonstrate their potential advantages over conventional austenitic stainless steels (SS), we performed in-situ ion irradiation experiments with 1 MeV krypton at 300 °C on two HEAs and a 316H SS under an identical irradiation condition. The irradiation introduced a high density of dislocation loops in all materials, and the microstructural evolution as a function of dose was similar for HEAs and 316H SS. Nanoindentation tests showed that the degree of irradiation hardening was also comparable between them. Furthermore, the similar microstructural evolution and irradiation hardening behavior between the HEAs and 316H indicate that, at low temperatures (≤300 °C), the irradiation damage of fcc alloys is not sensitive to compositional variation and configurational entropy.

36 MATERIALS SCIENCE↗

Back to functional hydrides: Effects of neutron-irradiated microstructure on hydrogen retention in yttrium hydride

Functional hydrides are promising candidates for advanced nuclear reactors, particularly in portable or transportable applications, due to their high hydrogen-retention capabilities, enabling efficient neutron moderation, and compact reactor design. However, hydrogen mobility in hydrides at elevated irradiation temperatures poses significant technological challenges, necessitating a comprehensive understanding of their irradiation behavior. Furthermore, this study investigated the microstructural and chemical stability of neutron-irradiated yttrium hydrides to assess their hydrogen-retention capacity. A targeted literature review was also conducted to contextualize neutron-irradiation effects on functional hydrides with regards to structural stability and hydrogen retention. Experimental characterizations revealed that, at high temperatures, irradiated hydrides retained their phase stability, which was likely enhanced by irradiation-induced microstructure evolution. Notably, an amorphous yttrium and oxygen -rich surface layer was present at the free surface of the hydride. Its thickness decreased while a continuous crystalline Y-O-rich layer was formed with increasing neutron damage. Additionally, the number density of dislocation loops and cavities generally increased as a function of neutron dose. First-principles calculations of hydrogen behavior within yttrium vacancy clusters in yttrium hydrides demonstrated vacancy-size-dependent hydrogen stability and configuration, highlighting the role of vacancy geometry in regulating hydrogen retention. Thus, the presence of irradiation-induced dislocation loops and cavities were hypothesized to improve hydrogen retention. Collectively, these findings advance the understanding of hydride behavior under neutron irradiation as well as their technological readiness for portable or transportable nuclear reactors.

Defect clusters↗

Influence of quenching agent on microstructure, properties and thermal stress of SiC{sub p}/2009 composites

15% vol. SiC{sub p}/2009 composites prepared by powder metallurgy were quenched in room temperature water and 20% polyethylene glycol (PEG) solution respectively, then aged naturally. The influence of quenching agent on microstructure, properties and thermal stress of SiC{sub p}/2009 composites were investigated by means of scanning/transmission electron microscope, hardness and tensile test. The results showed that the number of precipitated phase in water quenched composites increased, with much finer in size and more homogeneous in distribution compared with 20% PEG quenched one. Meanwhile, the density of dislocation in composites by water quenching was also much higher. Intergranular corrosion did not occur with the two quenching agents. The 20% PEG quenched composites exhibited slight lower hardness and higher electrical conductivity than that of water quenched one. The two quenched composites showed same level in tensile strength, but the yield strength of water-quenched composites was higher (8 MPa, 3%). The usage of 20% PEG reduced thermal stress and minimized warping deformation of the parts, it is a more suitable quenching agent for SiC{sub p}/2009 composites in engineering application fields. - Highlights: •SiC{sub p}/2009 composites quenched by water and 20% PEG solution were investigated. •Aging precipitation behavior of SiC{sub p}/2009 composites is sensitive to quenchant. •Influence of quenching agent on properties of SiC{sub p}/2009 composites are minimal. •Quenching with 20% PEG reduces thermal stress of SiC{sub p}/2009 composites remarkably. •20% PEG is a more suitable quenching agent for SiC{sub p}/2009 composites than water.

36 MATERIALS SCIENCE↗

Ultrafine grained structure and improved mechanical properties of low temperature friction stir spot welded 6061-T6 Al alloys

Highlights: • Friction stir spot welding of Al alloy was successfully done at low rotation speed. • The highest welding temperature was lower than 200 °C. • The average grain size of less than 500 nm was formed in the stir zone. • No hardness reduction of the HAZ region could be detected. • Shear tensile tests of the welds revealed a maximum shear load of about 5400 N. - Abstract: In this study, 1 mm thick 6061-T6 aluminum alloy plates were subjected to friction stir spot welding (FSSW) at a very low rotation speed of 30, 40 and 50 rpm, aiming to prevent the hardness reduction in the heat affected zone (HAZ) of this precipitate hardening Al joints. Two kinds of rotating tools, namely, one with a 1 mm long probe and the other one with a flat shoulder without a probe, were used and the corresponding force applied to the rotating tools was ranged from 4 to 8 tons. Under this special welding condition, the highest welding temperature was measured lower than 200 °C. As a result, no hardness reduction of the HAZ region could be detected and an ultrafine grain structure with a high density of dislocations was formed in the stir zone. The average grain size obtained in the stir zone was less than 500 nm for all the welds, which was much smaller than that in conventional FSSW processed 6061-T6 Al joints. In addition, no hook-like bonding ligaments were formed in the joints due to the very different material flows and the shear tensile tests showed that the spot welds prepared by the low speed FSSW can reach a maximum shear load of about 5400 N, much higher than those prepared by the conventional FSSW technique.

36 MATERIALS SCIENCE↗

Evolution of the mechanical properties of a cobalt-based alloy under thermal shocks

A cobalt-base alloy manufactured by hot isostatic pressing sintering (HIP) was investigated in the present work. A series of quenching thermal-shock experiments were carried out to study the effects of thermal-cycle shocks on this new cobalt-based alloy. Scanning Electron Microscope (SEM) and Energy Dispersion Spectrum (EDS) were employed to observe the evolution of microstructures under thermal-shock cycles. Results show that some floccus Co 3 W 3 C precipitated around the WC particles after several thermal-shock cycles. These precipitates and the carbide particles correspond to the locations with the high-stress concentration. The mechanical properties evolution under thermal-shock cycles was analyzed by Nanoindentation tests. The nanohardness presents no noticeable change with thermal-shock cycles. However, the reduced modulus demonstrates a decreasing trend with the thermal-shock cycles. The variation of the mechanical properties has an unestimated relationship with the residual stress and densities of dislocations caused by thermal shocks. Furthermore, the present work pointed out that the precipitates around the carbides are the places where the thermal fatigue crack initiated. How to deal with the precipitates will be the optimized way for this material.

36 MATERIALS SCIENCE↗

Strain-rate dependent deformation mechanisms in single-layered Cu, Mo, and multilayer Cu/Mo thin films

Here, strain-rate sensitivity and rate-dependent hardness, over a range of 10 -2 to 10 2 s -1 , of sputter-deposited single-layered Cu, Mo, and 5 nm Cu/ 5 nm Mo, and 100 nm Cu/ 100 nm Mo multilayer films with a total film thickness of 5 μm were measured using nanoindentation. The plastic zone underneath the nanoindents was characterized via cross-sectional transmission electron microscopy (XTEM). The multilayer films exhibited enhanced hardness but slightly reduced strain-rate sensitivity with decreasing layer thickness from 100 nm to 5 nm. Only the 5 nm Cu/ 5 nm Mo multilayer film exhibited shear bands underneath the nanoindents, and the size of the shear bands increased with increasing strain rate. In contrast, the 100 nm Cu/ 100 nm Mo multilayer film exhibited material pile-up around the indents and significant nanotwinning within Cu grains. The effect of strain rate and layer thickness on the hardness and strain rate sensitivity of the multilayer thin films is interpreted using a modified confined layer slip (CLS) model. The reduced rate sensitivity at 5 nm as compared to 100 nm correlates with abundant growth nanotwins in the Cu grains in 100 nm and formation of shear bands in 5 nm multilayers. In single layer films, a substructure with a high density of dislocations was observed consistent with the plastic strain gradient in the indent plastic zone. No evidence of deformation twins was noted in any of the samples.

36 MATERIALS SCIENCE↗

Additively manufactured refractory high-entropy alloys with superior radiation resistance

Refractory high-entropy alloys (RHEAs) are promising candidates for next-generation nuclear and high-temperature applications. Among many approaches to manufacture RHEAs, additive manufacturing (AM) represents the most recent and advanced metal manufacturing method which allows near-net-shape manufacturing to reduce material waste and post-processing time. However, performance of AM RHEAs under complex irradiation conditions remains largely unexplored. Here, in this study, we demonstrate for the first time the response of directed energy deposition (DED) AM quaternary RHEAs (HfTaVW, CrTaVW) subjected to sequential dual-beam ion irradiation, consisting of helium pre-implantation followed by high-dose heavy ion bombardment. Compositions of DED AM RHEAs were selected using Monte Carlo (MC) simulations based on a cluster expansion (CE) Hamiltonian parameterized by density functional theory (DFT). Post-irradiation microstructural characterization revealed that the AM RHEA maintained remarkable stability, with suppressed helium bubble growth and reduced defect accumulation compared to conventional alloys. Even at high doses (∼100 dpa), the alloy exhibited no void swelling, a low density of dislocation loops, and no evidence of severe degradation. These results highlight the intrinsic ability of AM-derived microstructures and multicomponent chemistry to synergistically mitigate irradiation effects. Our findings establish AM RHEAs as a class of materials with superior resistance to radiation damage under conditions relevant to advanced fusion and fission environments and demonstrate the importance of sequential ion beam studies in evaluating their long-term performance.

36 MATERIALS SCIENCE↗

Grain subdivision and structural modifications by high-energy heavy ions in UO 2 with different initial grain size

Irradiation with 84 MeV Xe ions at peak fluence above 7 × 10 17 ions/cm 2 has been carried out on two UO 2 samples with different initial grain sizes at 300 °C and 500 °C. Characterization of both grain structure and bubble morphology has been performed using transmission electron microscopy, image analysis and precession electron diffraction. The bubble size in the large-grained sample was smaller than that in the standard-grain sample, confirming fission gas precipitation resistance in the former. The ion irradiation in the high electronic energy deposition range has caused formation of a large density of dislocations which resulted in grain polygonization for the sample with standard grain size, which was observed in multiple lamellas extracted next to each other at peak dose. The sample with large grains showed inconsistent behavior. In one case, dislocation pile-up occurred, but no sub-grain formation was observed. An adjacent location showed sub-grain formation, even if to less extent compared to the standard grain-size sample. Furthermore, these findings suggest a limited polygonization resistance in large-grained UO 2 compared to standard-grain UO 2 . Recrystallization of both sample surfaces was present, leaving unclear if this is a surface effect or a consequence of the highest energy deposition rate in this area.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Modification of Ni-20Cr corrosion dealloying behavior in molten fluorides via cold work induced plastic deformation

The corrosion dealloying behavior of cold-worked (CW) Ni20Cr alloy (wt%) was studied in molten LiF-NaF-KF (or FLiNaK) salts at 600 °C, equal to a homologous temperature (TH) of 0.52. Alloys were cold-rolled to achieve reductions of thickness of 10%, 30%, and 50% introducing plastic deformation and a high density of dislocations. Potentiostatic holds (Eapplied) were applied in two different electrode potential regimes. At 1.75VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, Cr dealloying to Cr(II) and Cr(III) is predominant, while at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, both Ni and Cr are oxidized in molten FLiNaK at 600 °C. In these potential regimes, dealloyed Ni20Cr displayed bicontinuous porosity within the grain interior and at grain boundaries, driven by the high driving force for Cr dissolution and sustained by defect mediated outward solid state diffusion of Cr in parallel with surface diffusion of Ni. The bicontinuous porous structure developed was observed to undergo further coarsening and densification of the Ni-rich ligaments at a higher electrode potential. The main effect of CW observed is the introduction of plastic deformation and dislocation substructures that serve as short-circuit paths for Cr solid state diffusion to surfaces exposed to FLiNaK. This modified the evolution of the bicontinuous porous structure which increased with CW substantially. Kinetic analysis reveals that the Cr dealloying at +1.75 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ and 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ is initially charge transfer controlled, except for the 50% CW condition at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, where the process becomes limited by slow Cr defect mediated bulk diffusion. The rate determining factors are explored and compared to experimental results.

Chan, Ho Lun↗

Impact of pre-existing disorder on radiation defect dynamics in Si

The effect of pre-existing lattice defects on radiation defect dynamics in solids remains unexplored. Here, we use a pulsed beam method to measure the time constant of defect relaxation for 500 keV Ar ion bombardment of Si at 100 °C with the following two representative types of pre- existing lattice disorder: (i) point defect clusters and (ii) so-called “clamshell” defects consisting of a high density of dislocations. Results show that point defect clusters slow down defect relaxation processes, while regions with dislocations exhibit faster defect interaction dynamics. These experimental observations demonstrate that the dynamic aspects of damage buildup, attributed to defect trapping-detrapping processes, can be controlled by defect engineering.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Molecular beam epitaxy and structural anisotropy of m-plane InN grown on free-standing GaN

This study reports on the growth of high-quality nonpolar m-plane [1100] InN films on free-standing m-plane GaN substrates by plasma-assisted molecular beam epitaxy. Optimized growth conditions (In/N ratio {approx}1 and T=390-430 deg. C) yielded very smooth InN films with undulated features elongated along the [1120] orientation. This directionality is associated with the underlying defect structure shown by the anisotropy of x-ray rocking curve widths parallel to the [1120] (i.e., 0.24 deg. - 0.34 deg.) and [0001] (i.e., 1.2 deg. - 2.7 deg.) orientations. Williamson-Hall analysis and transmission electron microscopy identified the mosaic tilt and lateral coherence length and their associations with different densities of dislocations and basal-plane stacking faults. Ultimately, very low band gap energies of {approx}0.67 eV were measured by optical absorption similar to the best c-plane InN.

36 MATERIALS SCIENCE↗