Search NASA⌕ Search

SEARCH · Search NASA

Results for “dynamic loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Application of integrated structural analysis to the high speed civil transport

The Integrated Structural Analysis (ISA) system was developed in response to the need to define lightweight structures early in the design process for military aircraft. The objective of the ISA system is to permit rapid development of an optimized skin and big-bones structure that insures that the requirements of strength, dynamics, loads, and weight are met. While the system was originally developed for fighter aircraft, it is applicable to commercial transports or any other structures. The design requirements dictate the structural arrangement and sizing limitations to be imposed.

Saff, C. R.↗

Effect of operating conditions on gearbox noise

Low contact ratio spur gears were tested in the NASA gear noise rig to study the noise radiated from the top of the gearbox. The measured sound power from the gearbox top was obtained from a near field acoustic intensity scan taken at 63 nodes just above the surface. The sound power was measured at a matrix of 45 operating speeds and torque levels. Results are presented in the form of a spectral speed map and as a plot of sound power versus torque (at constant speed) and as sound power versus speed (at constant torque). Because of the presence of vibration modes, operating speed was found to have more impact on noise generation than torque level. A NASA gear dynamics code was used to compute the gear tooth dynamic overload at the same 45 operating conditions used for the experiment. Similar trends were found between the analytical results for dynamic tooth overload and experimental results for sound power. Dynamic analysis may be used to design high quality gears with profile relief optimized for minimum dynamic load and noise.

Oswald, Fred B.↗

High-alpha vortex decoupling investigations on a chine forebody/Delta wing configuration at transonic Mach numbers

A test program conducted in the LaRC 8-foot Transonic Pressure Tunnel on a blended chine/delta wing model to verify the concept of controlled vortex decoupling via inboard leading-edge flaps for improved high-alpha lateral/directional characteristics is discussed. This test extended the Mach number range of a data base previously generated in a LaRC 7 ft. by 10 ft High Speed Tunnel investigation. Six-component force/moment, forebody surface pressures, and central and twin tall static and dynamic loads were measured at Mach numbers of 0.4 to 1.2; laser light-sheet visualizations were also performed. Selected data are analyzed and discussed, emphasizing lateral/directional improvements and tail environment enhanced attainable by leading-edge flaps in the maximum lift region.

Rao, Dhanvada M.↗

Rotorcraft airframe structural optimization for combined vibration and fatigue constraints

This paper addresses the application of a formal optimization technique in rotorcraft airframe structural design studies to reduce the structural weight, to lower airframe vibrations, and to enhance fatigue life of the structure. Vibration and fatigue considerations in airframe design are described. An optimization methodology based on the use of a nonlinear programming technique to size airframe structural members subjected to constraints on weight, vibration response and fatigue stresses under dynamic loads, are described. The paper focuses on the development of necessary computational tools for airframe structural optimization and describes the sensitivity analysis procedure for these types of design constraints. Further, the paper describes the optimization procedure as implemented in a computer code called DYNOPT which is a unique operational combination of several newly developed Fortran codes as well as modification of existing codes consisting of the direct matrix abstraction modules of the MSC/NASTRAN Program and CONMIN optimizer. The application of the optimization procedure is demonstrated using an elastic-line model of the Bell AH-1G helicopter airframe structure and computational results are discussed.

Sareen, Ashish K.↗

A probabilistic approach to the evaluation of fatigue damage in a space propulsion system injector element

The fatigue damage of a space propulsion system component is computed using probabilistic structural analysis methods. The analysis takes into account the variations in static and dynamic loads, the uncertainty in structural damping, and the scatter in material fatigue resistance. The key elements of the probabilistic approach include: (1) a numerical engine model for describing the global component interface loads consistent with engine balance, (2) models for computing the local mode boundary conditions on the component, (3) a static structural analysis model that captures the strains at a damage critical location as a function of engine performance variables, (4) a finite element model for assessment of the random amplitude stress response due to random base and pressure excitations with uncertain power and correlation length, and (5) advanced first order reliability methods for computing the probabilities associated with the fatigue damage.

Rajagopal, K. R.↗

Computations of the unsteady flow about a generic wing/pylon/finned-store configuration

An overset grid approach is used to carry out a set of computations of the unsteady flow about a generic wing, pylon, and finned-store configuration. The geometry, discretization procedure, and governing equations are presented. Thin-layer Navier-Stokes solutions are presented for four store separation cases: store in carriage position, store at two different separation positions, and a time-accurate simulation of the forced store separation from the wing pylon carriage. Computational results are compared with wind tunnel data for the three 'static store' cases. Dynamic loads and trajectory data are presented for the forced separation case.

Meakin, Robert L.↗

Time Warp Operating System, Version 2.5.1

Time Warp Operating System, TWOS, is special purpose computer program designed to support parallel simulation of discrete events. Complete implementation of Time Warp software mechanism, which implements distributed protocol for virtual synchronization based on rollback of processes and annihilation of messages. Supports simulations and other computations in which both virtual time and dynamic load balancing used. Program utilizes underlying resources of operating system. Written in C programming language.

Bellenot, Steven F.↗

Damper Spring For Omega Seal

Damper spring reduces deflections of omega-cross-section seal, reducing probability of failure and extending life of seal. Spring is split ring with U-shaped cross section. Placed inside omega seal and inserted with seal into seal cavity. As omega seal compressed into cavity, spring and seal make contact near convolution of seal, and spring becomes compressed also. During operation, when seal dynamically loaded, spring limits deflection of seal, reducing stress on seal.

Maclaughlin, Scott T.↗

Thermostructural responses of carbon phenolics in a restrained thermal growth test

The thermostructural response of carbon phenolic components in a solid rocket motor (SRM) is a complex process. It involves simultaneous heat and mass transfer along with chemical reactions in a multiphase system with time-dependent material properties and boundary conditions. In contrast to metals, the fracture of fiber-reinforced composites is characterized by the initiation and progression of multiple failures of different modes such as matrix cracks, interfacial debonding, fiber breaks, and delamination. The investigation of thermostructural responses of SRM carbon phenolics is further complicated by different failure modes under static and dynamic load applications. Historically, there have been several types of post-firing anomalies found in the carbon phenolic composites of the Space Shuttle SRM nozzle. Three major failure modes which have been observed on SRM nozzles are pocketing (spallation), ply-lift, and wedge-out. In order to efficiently control these anomalous phenomena, an investigation of fracture mechanisms under NASA/MSFC RSRM (Redesigned Solid Rocket Motor) and SPIP (Solid Propulsion Integrity Program) programs have been conducted following each anomaly. This report reviews the current progress in understanding the effects of the thermostructural behavior of carbon phenolics on the failure mechanisms of the SRM nozzle. A literature search was conducted and a technical bibliography was developed to support consolidation and assimilation of learning from the RSRM and SPIP investigation efforts. Another important objective of this report is to present a knowledge-based design basis for carbon phenolics that combines the analyses of thermochemical decomposition, pore pressure stresses, and thermostructural properties. Possible areas of application of the knowledge-based design include critical material properties development, nozzle component design, and SRM materials control.

Wang, C. Jeff↗

Preliminary experimental results for a cryogenic brush seal configuration

Preliminary fluid nitrogen flow data are reported for a five-brush, ceramic-coated-rub-runner brush seal system, where the brushes and the rub runner were placed at each end of a centrally pressurized multifunction tester ('back-to-back' set of brushes) and tested at rotor speeds of 0, 10, 18, and 22.5 krpm. After testing, both the brushes and the ceramic-coated rub runner appeared pristine. The coating withstood both the thermomechanical and dynamic loadings with minor wear track scarring. The bristle tips showed some indication of material shearing (smearing) wear. The Ergun porous flow equation was applied to the brush seal data. The Ergun relation, which required heuristic information to characterize the coefficients, fit the gaseous data but was in poor agreement with the fluid results. The brush seal exit conditions were two phase. Two-phase, choked-flow design charts were applied but required one data point at each rotor speed to define the (C(sub f)A x Constant) flow and area coefficients. Reasonable agreement between prediction and data was found, as expected, but such methods are not to be construed as two-phase-flow brush seal analyses.

Carlile, J. A.↗

Localization of aeroelastic modes in mistuned high-energy turbines

The effects of blade mistuning on the aerodynamic characteristics of a class of bladed-disk assemblies, namely high energy turbines, are discussed. The specific rotor analyzed is the first stage of turbine blades of the oxidizer turbopump in the Space Shuttle Main Engine. The common occurrence of fatigue cracks for these turbine blades indicates the possibility of high dynamic loading. Since mistuning under conditions of weak interblade coupling has been shown to increase blade response amplitudes drastically for simple structural models of blade assemblies, it provides a plausible explanation for the occurrence of cracks. The focus here is on the effects of frequency mistuning on the aeroelastic stability of the assembly and on the aeroelastic mode shapes.

Smith, Todd E.↗

Thermographic characterization of stress during crack growth

A full-field-thermographic technique for imaging stress patterns in dynamically loaded structures using general purpose IR imaging and image processing hardware is described. The inspection technique is based on the thermoelastic effect. A simple geometry is examined, and the experimentally determined values for the stress invariant are shown to be consistent with theoretical and numerical calculations. The application of full-field-thermographic measurement would ensure that the observed stress field has a common sampling period, thus allowing the observation of rapidly occurring stress anomalies such as the propagation of a fatigue crack. Fatigue crack propagation in two consecutive thermoelastic stress images from an aluminum sample is shown.

Cramer, K. E.↗

Preliminary experimental results for a cryogenic brush seal configuration

Preliminary fluid nitrogen flow data are reported for a five-brush, ceramic-coated-rub-runner brush seal system, where the brushes and the rub runner were placed at each end of a centrally pressurized multifunction tester ('back-to-back' set of brushes) and tested at rotor speeds of 0, 10, 18, and 22.5 krpm. After testing, both the brushes and the ceramic-coated rub runner appeared pristine. The coating withstood both the thermomechanical and dynamic loadings with minor wear track scarring. The bristle tips showed some indication of material shearing (smearing) wear. The Ergun (1952) porous flow equation was applied to the brush seal data. The Ergun relation fit the gaseous data but was in poor agreement with the fluid results. The brush seal exit conditions were two phase. Two-phase, choked-flow design charts were applied but required one data point at each rotor speed to define the flow and area coefficients. Reasonable agreement between prediction and data was found, but such methods are not to be construed as two-phase-flow brush seal analyses.

Carlile, J. A.↗

An investigation of the fuel-optimal periodic trajectories of a hypersonic vehicle

Periodic trajectories were found to minimize the range-averaged fuel consumption. For a realistic hypersonic aircraft modeled as a point mass over a nonrotating, spherical Earth, the periodic orbit yielded a 15 percent improvement in fuel consumption over static cruise. Moreover, vehicle dynamic loading was contained within a realistic survivability envelope of 8 g's. The resulting periodic orbit is composed of very distinct flight regimes (Keplerian arc, atmospheric glide and powered climb), which may offer mission advantages over the static path.

Dewell, Larry D.↗

Computer program for analysis of high speed, single row, angular contact, spherical roller bearing, SASHBEAN. Volume 1: User's guide

The computer program SASHBEAN (Sikorsky Aircraft Spherical Roller High Speed Bearing Analysis) analyzes and predicts the operating characteristics of a Single Row, Angular Contact, Spherical Roller Bearing (SRACSRB). The program runs on an IBM or IBM compatible personal computer, and for a given set of input data analyzes the bearing design for it's ring deflections (axial and radial), roller deflections, contact areas and stresses, induced axial thrust, rolling element and cage rotation speeds, lubrication parameters, fatigue lives, and amount of heat generated in the bearing. The dynamic loading of rollers due to centrifugal forces and gyroscopic moments, which becomes quite significant at high speeds, is fully considered in this analysis. For a known application and it's parameters, the program is also capable of performing steady-state and time-transient thermal analyses of the bearing system. The steady-state analysis capability allows the user to estimate the expected steady-state temperature map in and around the bearing under normal operating conditions. On the other hand, the transient analysis feature provides the user a means to simulate the 'lost lubricant' condition and predict a time-temperature history of various critical points in the system. The bearing's 'time-to-failure' estimate may also be made from this (transient) analysis by considering the bearing as failed when a certain temperature limit is reached in the bearing components. The program is fully interactive and allows the user to get started and access most of its features with a minimal of training. For the most part, the program is menu driven, and adequate help messages were provided to guide a new user through various menu options and data input screens. All input data, both for mechanical and thermal analyses, are read through graphical input screens, thereby eliminating any need of a separate text editor/word processor to edit/create data files. Provision is also available to select and view the contents of output files on the monitor screen if no paper printouts are required. A separate volume (Volume-2) of this documentation describes, in detail, the underlying mathematical formulations, assumptions, and solution algorithms of this program.

Aggarwal, Arun K.↗

Stiffness-generated rigid-body mode shapes for Lanczos eigensolution with SUPORT DOF by way of a MSC/NASTRAN DMAP alter

When using all MSC/NASTRAN eigensolution methods except Lanczos, the analyst can replace the coupled system rigid-body modes calculated within DMAP module READ with mass orthogonalized and normalized rigid-body modes generated from the system stiffness. This option is invoked by defining MSC/NASTRAN r-set degrees of freedom via the SUPORT bulk data card. The newly calculated modes are required if the rigid-body modes calculated by the eigensolver are not 'clean' due to numerical roundoffs in the solution. When performing transient structural dynamic load analysis, the numerical roundoffs can result in inaccurate rigid-body accelerations which affect steady-state responses. Unfortunately, when using the Lanczos method and defining r-set degrees of freedom, the rigid-body modes calculated within DMAP module REIGL are retained. To overcome this limitation and to allow MSC/NASTRAN to handle SUPORT degrees of freedom identically for all eigensolvers, a DMAP Alter has been written which replaces Lanczos-calculated rigid-body modes with stiffness-generated rigid-body modes. The newly generated rigid-body modes are normalized with respect to the system mass and orthogonalized using the Gram-Schmidt technique. This algorithm has been implemented as an enhancement to an existing coupled loads methodology.

Abdallah, Ayman A.↗

Squeeze film dampers with oil hole feed

To improve the damping capability of squeeze film dampers, oil hole feed rather than circumferential groove feed is a practical proposition. However, circular orbit response can no longer be assumed, significantly complicating the design analysis. This paper details a feasible transient solution procedure for such dampers, with particular emphasis on the additional difficulties due to the introduction of oil holes. It is shown how a cosine power series solution may be utilized to evaluate the oil hole pressure contributions, enabling appropriate tabular data to be compiled. The solution procedure is shown to be applicable even in the presence of flow restrictors, albeit at the expense of introducing an iteration at each time step. Though not of primary interest, the procedure is also applicable to dynamically loaded journal bearings with oil hole feed.

Chen, P. Y. P.↗

DTS: Building custom, intelligent schedulers

DTS is a decision-theoretic scheduler, built on top of a flexible toolkit -- this paper focuses on how the toolkit might be reused in future NASA mission schedulers. The toolkit includes a user-customizable scheduling interface, and a 'Just-For-You' optimization engine. The customizable interface is built on two metaphors: objects and dynamic graphs. Objects help to structure problem specifications and related data, while dynamic graphs simplify the specification of graphical schedule editors (such as Gantt charts). The interface can be used with any 'back-end' scheduler, through dynamically-loaded code, interprocess communication, or a shared database. The 'Just-For-You' optimization engine includes user-specific utility functions, automatically compiled heuristic evaluations, and a postprocessing facility for enforcing scheduling policies. The optimization engine is based on BPS, the Bayesian Problem-Solver (1,2), which introduced a similar approach to solving single-agent and adversarial graph search problems.

Hansson, Othar↗