Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrical conversion efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Electric Motor Thermal Management

Thermal management enables more efficient and cost-effective motors. This Annual Merit Review presentation describes the technical accomplishments and progress in electric motor thermal management R&D over the last year. This project supports a broad industry demand for data, analysis methods, and experimental techniques to improve and better understand motor thermal management.

30 DIRECT ENERGY CONVERSION↗

Reduced Cu(InGa)Se 2 Thickness in Solar Cells Using a Superstrate Configuration

This project by the Institute of Energy Conversion (IEC) and the Department of Electrical and Computer Engineering at the University of Delaware sought to develop the technology and underlying science to enable reduced cost of Cu(InGa)Se 2 manufacturing by reducing the thickness of the Cu(InGa)Se 2 absorber layer by half compared to typical production. The approach to achieve this was to use the superstrate cell configuration in which light is incident on the cell through the glass. This structure facilitates optical enhancement approaches needed to achieve high efficiency with Cu(InGa)Se 2 thicknesses less than 1 µm. The primary objective was to demonstrate a Cu(InGa)Se 2 cell with absorber thickness 0.5 - 0.7 µm and 17% efficiency, along with a quantitative loss analysis to define a pathway to 20% efficiency. Additional objectives were the development of stable TCO and buffer layers or contact layers to withstand the Cu(InGa)Se 2 deposition temperature and of advanced optical enhancement methods. The underlying fundamental science needed to effectively transition these outcomes to large scale was addressed by extensive materials and device characterization and by development of comprehensive optical models. Two different superstrate configurations have been investigated. A frontwall cell is illuminated through the glass to the primary front junction of the device. This configuration has been used for previous efforts on superstrate Cu(InGa)Se 2 but performance has been limited by interdiffusion or reaction with CdS or other buffer layers. In this project, several approaches to overcome these limitations were explored using CdS, ZnO and ZnSe buffer layers. In each case, mechanisms that limit device performance were identified using detailed characterization of the materials and junctions. Due to the junction formation difficulties, efforts were concentrated on a new backwall configuration in which light is incident through the substrate into the back of the absorber layer. The primary junction is then formed after Cu(InGa)Se 2 deposition. This allows the potential benefits of superstrate cells for optical enhancement while maintaining processing advantages of the substrate configuration and avoiding the harmful effects of high temperature deposition on p-n junction formation. Backwall devices have outperformed substrate cells at absorber thicknesses of 0.1-0.5 µm through enhanced JSC due to easy incorporation of a Ag reflector and, with light incident on the absorber, the elimination of parasitic absorption in the CdS buffer. An efficiency of 9.7% has been achieved for a backwall Cu(InGa)Se 2 device with absorber thickness ~0.4 μm. A critical achievement that enabled implementation of the backwall cell was the development of a transparent back contact using MoO 3 or WO 3 . Processes for controlled deposition of each material by reactive rf sputtering from metal targets were developed. These contacts have wide bandgaps making them well-suited for application as contacts for backwall devices as well as potential use in bifacial cells and as the top cell of tandem CuInSe 2 -based devices. Optical enhancement will be critical for further improvements. Wet chemical texturing of ZnO films has been developed for a simple, low cost light-trapping scheme for backwall superstrate devices to enhance long wavelength quantum efficiency. An aqueous oxalic acid etch was developed and found to strongly texture sputtered ZnO with high haze ≈ 0.9 observed across the whole spectrum. And finally, advanced optical models have been developed to assist the characterization and optimization of Cu(InGa)Se 2 cells with thin absorbers

14 SOLAR ENERGY↗

Assessment of a field-aligned ICRF antenna

Impurity contamination and localized heat loads associated with ion cyclotron range of frequency (ICRF) antenna operation are among the most challenging issues for ICRF utilization.. Another challenge is maintaining maximum coupled power through plasma variations including edge localized modes (ELMs) and confinement transitions. Here, we report on an experimental assessment of a field aligned (FA) antenna with respect to impurity contamination, impurity sources, RF enhanced heat flux and load tolerance. In addition, we compare the modification of the scrape of layer (SOL) plasma potential of the FA antenna to a conventional, toroidally aligned (TA) antenna, in order to explore the underlying physics governing impurity contamination linked to ICRF heating. The FA antenna is a 4-strap ICRF antenna where the current straps and antenna enclosure sides are perpendicular to and the Faraday screen rods are parallel to the total magnetic field. In principle, alignment with respect to the total magnetic field minimizes integrated E∥ (electric field along a magnetic field line) via symmetry. Consistent with expectations, we observed that the impurity contamination and impurity source at the FA antenna are reduced compared to the TA antenna. In both L and H-mode discharges, the radiated power is 20–30% lower for a FA-antenna heated discharge than a discharge heated with the TA-antennas. Further we observe that the fraction of RF energy deposited upon the antenna is less than 0.4 % of the total injected RF energy in dipole phasing. The total deposited energy increases significantly when the FA antenna is operated in monopole phasing. The FA antenna also exhibits an unexpected load tolerance for ELMs and confinement transitions compared to the TA antennas. However, inconsistent with expectations, we observe RF induced plasma potentials to be nearly identical for FA and TA antennas when operated in dipole phasing. In monopole phasing, the FA antenna has the highest plasma potentials and poor heating efficiency despite calculations indicating low integrated E∥. In mode conversion heating scenario, no core waves were detected in the plasma core indicating poor wave penetration. For monopole phasing, simulations suggest the antenna spectrum is peaked at very short wavelength and full wave simulations show the short wavelength has poor wave penetration to the plasma core.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Program Final Report - Develop Thermoelectric Technology for Automotive Waste Heat Recovery

We conducted a vehicle analysis to assess the feasibility of thermoelectric technology for waste heat recovery and conversion to useful electrical power and found that eliminating the 500 W of electrical power generated by the alternator corresponded to about a 7% increase in fuel economy (FE) for a small car and about 6% for a full size truck. Electric power targets of 300 W were established for city and highway driving cycles for this project. We obtained critical vehicle level information for these driving cycles that enabled a high-level design and performance analysis of radiator and exhaust gas thermoelectric subsystems for several potential vehicle platforms, and we identified the location and geometric envelopes of the radiator and exhaust gas thermoelectric subsystems. Based on this analysis, we selected the Chevrolet Suburban as the most suitable demonstration vehicle for this project. Our modeling and thermal analysis assessment of a radiator-based thermoelectric generator (TEG), however, revealed severe practical limitations. Specifically the small temperature difference of 100°C or less between the engine coolant and ambient air results in a low Carnot conversion efficiency, and thermal resistance associated with air convection would reduce this conversion efficiency even further. We therefore decided not to pursue a radiator-based waste heat recovery system and focused only on the exhaust gas. Our overall approach was to combine science and engineering: (1) existing and newly developed TE materials were carefully selected and characterized by the material researcher members of our team, and most of the material property results were validated by our research partners, and (2) system engineers worked closely with vehicle engineers to ensure that accurate vehicle-level information was used for developing subsystem models and designs, and the subsystem output was analyzed for potential fuel economy gains. We incorporated material, module, subsystem, and integration costs into the material selection criteria in order to balance various materials, module and subsystem design, and vehicle integration options. Our work on advanced TE materials development and on TEG system design, assembly, vehicle integration, and testing proceeded in parallel efforts. Results from our two preliminary prototype TEGs using only Bi-Te TE modules allowed us to solve various mechanical challenges and to finalize and fine tune aspects of the design and implementation. Our materials research effort led us to quickly abandon work on PbTe and focus on the skutterudite materials due to their superior mechanical performance and suitability at automotive exhaust gas operating temperatures. We synthesized a sufficiently large quantity of skutterudite material for module fabrication for our third and final prototype. Our TEG#3 is the first of its kind to contain state-of-the-art skutterudite-based TE modules to be installed and tested on a production vehicle. The design, which consisted of 24 skutterudite modules and 18 Bi-Te modules, attempted to optimize electrical power generation by using these two kinds of TE modules that have their peak performance temperatures matched to the actual temperature profile of the TEG during operation. The performance of TEG#3 was limited by the maximum temperature allowable for the Bi-Te TE modules located in the colder end of the TEG, resulting in the operating temperature for the skutterudite modules to be considerably below optimum. We measured the power output for (1) the complete TEG (25 Watts) and (2) an individual TE module series string (1/3 of the TEG) operated at a 60°C higher temperature (19 Watts). We estimate that under optimum operating temperature conditions, TEG#3 will generate about 235 Watts. With additional improvements in thermal and electrical interfaces, temperature homogeneity, and power conditioning, we estimate TEG#3 could deliver a power output of about 425 Watts.

30 DIRECT ENERGY CONVERSION↗

The 2020 photovoltaic technologies roadmap

Over the past decade, the global cumulative installed photovoltaic (PV) capacity has grown exponentially, reaching 591 GW in 2019. Rapid progress was driven in large part by improvements in solar cell and module efficiencies, reduction in manufacturing costs and the realization of levelized costs of electricity that are now generally less than other energy sources and approaching similar costs with storage included. Given this success, it is a particularly fitting time to assess the state of the photovoltaics field and the technology milestones that must be achieved to maximize future impact and forward momentum. This roadmap outlines the critical areas of development in all of the major PV conversion technologies, advances needed to enable terawatt-scale PV installation, and cross-cutting topics on reliability, characterization, and applications. Each perspective provides a status update, summarizes the limiting immediate and long-term technical challenges and highlights breakthroughs that are needed to address them. In total, this roadmap is intended to guide researchers, funding agencies and industry in identifying the areas of development that will have the most impact on PV technology in the upcoming years.

14 SOLAR ENERGY↗

Potential Integration Between Residual Biogenic Process Resources and Greener Hydrogen Production from Steam Reformers

Biomass conversion processes have varying efficiencies towards specific products like liquid fuels; process inefficiencies result in byproducts such as off-gases, heat, and solid residues such as char. The efficient use of these byproducts is key towards getting the maximum sustainability benefits from valuable biomass resources. For example, there are various utility product options that can utilize heat and off-gases from biomass pyrolysis processes; they include process heat and steam, hydrogen, fuel gas, and electricity. Further, there is potential for the use of the off-gases to supplement natural gas feed into steam reformers for hydrogen production. This presentation highlights results from previous analyses on tradeoffs based on utility byproduct choices (https://doi.org/10.1039/D3SE00745F); maximizing hydrogen production from off-gases is one potential winning strategy. This leads to the question regarding the utilization of these off-gases in existing steam reformers and the process impacts from feeding off-gases. Process modeling of a steam reformer system (https://doi.org/10.1002/adsu.20230021) quantifies those impacts and shows how much off-gas substitution is possible within the limits of an existing design with such an integration strategy.

biogenic gases↗

Low-temperature high-mobility amorphous IZO for silicon heterojunction solar cells

Parasitic absorption in the transparent conductive oxide (TCO) front electrode is one of the limitations of silicon heterojunction (SHJ) solar cells efficiency. To avoid such absorption while retaining high conductivity, TCOs with high electron mobility are preferred over those with high carrier density. Here, we demonstrate improved SHJ solar cell efficiencies by applying high-mobility amorphous indium zinc oxide (a-IZO) as the front TCO. We sputtered a-IZO at low substrate temperature and low power density and investigated the optical and electrical properties, as well as subband tail formation-quantified by the Urbach energy (E U )-as a function of the sputtering oxygen partial pressure. We obtain an E U as low as 128 meV for films with the highest Hall mobility of 60 cm 2 /Vs. When comparing the performance of a-IZO films with indium tin oxide (ITO) and hydrogenated indium oxide (IO:H), we find that IO:H (115 cm 2 /Vs) exhibits a similar E U of 130 meV, while ITO (25 cm 2 /Vs) presents a much larger E U of up to 270 meV. The high film quality, indicated by the low E U , the high mobility, and low free carrier absorption of the developed a-IZO electrodes, result in a significant current improvement, achieving conversion efficiencies over 21.5%, outperforming those with standard ITO.

14 SOLAR ENERGY↗

Achievement of 6.03% conversion efficiency of dye-sensitized solar cells with single-crystalline rutile TiO{sub 2} nanorod photoanode

The rutile TiO{sub 2} nanorods (RTNs) with the length of 40-130 nm and diameters approximately 8-15 nm, containing some 300-500 nm sized RTN aggregates and 6% of anatase TiO{sub 2} nanocrystals, were prepared by surfactant-assisted hydrothermal method. The dye-sensitized solar cell (DSC) based on the RTNs exhibited power conversion efficiency of 6.03%. As compared to P25 TiO{sub 2} based DSC, RTNs based DSC shows improved light-harvesting and Brunauer-Emmett-Teller surface area, leading to an increase in short-circuit current (J{sub sc}) by 40.6%.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Conductive Metallophthalocyanine Framework Films with High Carrier Mobility as Efficient Chemiresistors

Abstract The poor electrical conductivity of two‐dimensional (2D) crystalline frameworks greatly limits their utilization in optoelectronics and sensor technology. Herein, we describe a conductive metallophthalocyanine‐based NiPc‐CoTAA framework with cobalt(II) tetraaza[14]annulene linkages. The high conjugation across the whole network combined with densely stacked metallophthalocyanine units endows this material with high electrical conductivity, which can be greatly enhanced by doping with iodine. The NiPc‐CoTAA framework was also fabricated as thin films with different thicknesses from 100 to 1000 nm by the steam‐assisted conversion method. These films enabled the detection of low‐concentration gases and exhibited remarkable sensitivity and stability. This study indicates the enormous potential of metallophthalocyanine‐based conductive frameworks in advanced stand‐off chemical sensors and provides a general strategy through tailor‐make molecular design to develop sensitive and stable chemical sensors for the detection of low‐concentration gases.

Yue, Yan↗

Conductive Metallophthalocyanine Framework Films with High Carrier Mobility as Efficient Chemiresistors

Abstract The poor electrical conductivity of two‐dimensional (2D) crystalline frameworks greatly limits their utilization in optoelectronics and sensor technology. Herein, we describe a conductive metallophthalocyanine‐based NiPc‐CoTAA framework with cobalt(II) tetraaza[14]annulene linkages. The high conjugation across the whole network combined with densely stacked metallophthalocyanine units endows this material with high electrical conductivity, which can be greatly enhanced by doping with iodine. The NiPc‐CoTAA framework was also fabricated as thin films with different thicknesses from 100 to 1000 nm by the steam‐assisted conversion method. These films enabled the detection of low‐concentration gases and exhibited remarkable sensitivity and stability. This study indicates the enormous potential of metallophthalocyanine‐based conductive frameworks in advanced stand‐off chemical sensors and provides a general strategy through tailor‐make molecular design to develop sensitive and stable chemical sensors for the detection of low‐concentration gases.

Yue, Yan↗

Improved conversion efficiency of dye sensitized solar cell using Zn doped TiO{sub 2}-ZrO{sub 2} nanocomposite

TiO{sub 2}-ZrO{sub 2} and Zn doped TiO{sub 2}-ZrO{sub 2} nanocomposites were prepared by hydrothermal method for dye sensitized solar cell (DSSC) application. The structural and optical properties were investigated by X –ray diffraction (XRD) and UV-Visible spectroscopy respectively. XRD results revealed the formation of material in nano size. The average crystallite size is 22.32 nm, 17.41 nm and 6.31 nm for TiO{sub 2}, TiO{sub 2}-ZrO{sub 2} and Zn doped TiO{sub 2}-ZrO{sub 2} nanocomposites respectively. The optical bandgap varies from 2.04 eV to 3.75 eV. Dye sensitized solar cells were fabricated using the prepared material. Pomegranate juice was used as a sensitizer and graphite coated conducting glass plate was used as counter electrode. The I – V characteristics were recorded to measure photo response of DSSC. Photovoltaic parameter like open circuit voltage, power conversion efficiency, and fill factor were evaluated for fabricated solar cell. The power conversion efficiency of DSSC fabricated with TiO{sub 2}, TiO{sub 2}-ZrO{sub 2} and Zn doped TiO{sub 2}-ZrO{sub 2} nanocomposites were found 0.71%, 1.97% and 4.58% respectively.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Encouraging Combined Heat and Power in California Buildings

Governor Brown’s research priorities include an additional 6.5 GW of combined heat and power (CHP) by 2030. As of 2009, roughly 0.25 GW of small natural gas and biogas fired CHP is documented by the Self-Generation Incentive Program (SGIP) database. The SGIP is set to expire, and the anticipated grid de-carbonization based on the development of 20 GW of renewable energy will influence the CHP adoption. Thus, an integrated optimization approach for this analysis was chosen that allows optimizing the adoption of distributed energy resources (DER) such as photovoltaics (PV), CHP, storage technologies, etc. in the California commercial sector from the building owners’ perspective. To solve this DER adoption problem the Distributed Energy Resources Customer Adoption Model (DER-CAM), developed by the Lawrence Berkeley National Laboratory and used extensively to address the problem of optimally investing and scheduling DER under multiple settings, has been used. The application of CHP at large industrial sites is well known, and much of its potential is already being realized. Conversely, commercial sector CHP, especially those above 50 to 100 kW peak electricity load, is widely overlooked. In order to analyze the role of DER in CO 2 reduction, 147 representative sites in different climate zones were selected from the California Commercial End Use Survey (CEUS). About 8000 individual optimization runs, with different assumptions for the electric tariffs, natural gas costs, marginal grid CO 2 emissions, and nitrogen oxide treatment costs, SGIP, fuel cell lifetime, fuel cell efficiency, PV installation costs, and payback periods for investments have been performed. The most optimistic CHP potential contribution in this sector in 2020 will be 2.7 GW. However, this result requires a SGIP in 2020, 46% average electric efficiency for fuel cells, a payback period for investments of 10 years, and a CO 2 focused approach of the building owners. In 2030 it will be only 2.5 GW due to the anticipated grid decarbonization. The 2030 result requires a 60% electric efficiency and 20 year life time for fuel cells, a payback period of 10 years, and a CO 2 minimization strategy of building owners. Finally, the possible CHP potential in 2030 shows a significant variance between 0.2 GW and 2.5 GW, demonstrating the complex interactions between technologies, policies, and customer objectives.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Assessments of advanced reactor heat supply to high temperature industrial unit operations: Heat Engines and Heat Pumps

In this report, the feasibility of employing Advanced Nuclear Reactors to supply the necessary high-quality heat to Industrial Processes is investigated. As a first step, the most relevant industrial applications that could benefit from this coupling were identified. Four industries including petroleum refining (distillation, catalyst regeneration, hydro-steam cracking), chemical polymers, steel manufacturing (metals annealing/soaking) and cement manufacturing (calcination of limestone and dolomite industries) were considered. An overview of the heat duties, i.e., the temperatures and thermal powers required by representative plants of the different processes, was provided. Secondly, the thermodynamic conditions of the steam produced by representative designs of Advanced Reactor concepts (Liquid Metal Fast Breeder Reactors, Molten Salt Reactors, and High Temperature Gas-cooled Reactors) were summarized. The comparison between the requirements of the industrial processes and the capabilities of the candidate nuclear power plants showed that only a few processes could benefit from the coupling. Although Advanced Reactors operate at higher temperatures than Light Water Reactors, the thermodynamic conditions of the generated steam flow rates are generally not suitable for the selected applications. At the same time, data indicate that most of the processes can be suitably supplied if the temperature of steam is elevated to 900 °C. One possible solution to boost the quality of the steam from the nuclear island involves the use of a heat pump. Based on a technology similar to that found in refrigerators and air conditioners, heat pumps extract heat from a source, elevate its temperature and transfer it to where it is needed. A simple numerical example illustrating the viability of this method is described. Specifically, the energy conversion cycle of a conventional Pressurized Water Reactor was extended to incorporate a compressor to raise the heating value of the steam produced by the reactor. Two reference configurations, i.e., one where the industrial process coupled to the nuclear power plant exhausts saturated liquid and the other where it exhausts saturated steam, were considered. The thermal efficiencies achievable by increasing the heating value of the reactor steam in this way are significantly greater than by direct electric heating.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Atomic Structure, Dynamics, Changes in Chemical Bonding and Semiconductor-Metal Transition in Sb 2 Se 3 : A Remarkable Material for Quantum Networks and Energy Applications

Antimony sesquiselenide has become an outstanding functional material for photovoltaics, energy storage and transformation, memory and photonic applications. Sb 2 Se 3 is one of the most successful emerging solar light absorbers and has also been identified as a highly promising ultralow-loss phase-change material (PCM) for next-generation coherent nanophotonic processors, photonic tensor cores, quantum and neuromorphic networks. Unlike benchmark telluride PCMs, Sb 2 Se 3 features a quasi-one-dimensional (1D) crystalline structure consisting of (Sb 4 Se 6 ) ∞ ribbons, lacks the typical PCM chemical bonding, and undergoes an extended semiconductor-metal transition above the melting point. Consequently, the origin of high optical contrast between crystalline (SET) and amorphous (RESET) logic states remains elusive and presents a significant challenge. Using high-energy X-ray diffraction and Raman spectroscopy over a wide temperature range, supported by first-principles simulations and complemented by thermal, optical and electrical measurements, as well as by 121 Sb-Mossbauer spectroscopy, the quasi-1D network of orthorhombic antimony sesquiselenide was found to undergo significant evolution in amorphous and supercooled Sb 2 Se 3 , leading to lower coordination, shorter interatomic distances and a higher p-electron density on antimony, indicating changes in chemical bonding. The observed novel Sb 2 Se 3 nanocrystalline polymorph, characterized by trigonal antimony coordination and more isolated Sb-Se ribbons, could help reduce multiple trapping defect states in the bandgap, which are typical of orthorhombic Sb 2 Se 3 , thereby enhancing the power-conversion efficiency of photovoltaic devices. Semimetallic and metallic liquid Sb 2 Se 3 exhibit a gradual transformation into a denser 2D and/or 3D network with higher antimony coordination. Localized electron states in the pseudogap are becoming extended, leading to an increase in electronic conductivity σ following the relationship σ ∝ N(E F ) 2 . Liquid Sb 2 Se 3 also appears to be strongly fragile, with a nonmonotonic change in viscosity and higher atomic mobility in the metallic liquid. Furthermore, these results explain extraordinary functionalities of Sb 2 Se 3 for photonic and energy applications.

antimony↗

Biomass Energy Data Book: Edition 2

The Biomass Energy Data Book is a statistical compendium prepared and published by Oak Ridge National Laboratory (ORNL) under contract with the Biomass Program in the Energy Efficiency and Renewable Energy (EERE) program of the Department of Energy (DOE). Designed for use as a convenient reference, the book represents an assembly and display of statistics and information that characterize the biomass industry, from the production of biomass feedstocks to their end use, including discussions on sustainability. This is the second edition of the Biomass Energy Data Book which is only available online in electronic format. There are five main sections to this book. The first section is an introduction which provides an overview of biomass resources and consumption. Following the introduction to biomass, is a section on biofuels which covers ethanol, biodiesel and bio-oil. The biopower section focuses on the use of biomass for electrical power generation and heating. The fourth section is on the developing area of biorefineries, and the fifth section covers feedstocks that are produced and used in the biomass industry. The sources used represent the latest available data. There are also four appendices which include frequently needed conversion factors, a table of selected biomass feedstock characteristics, assumptions for selected tables and figures, and discussions on sustainability. A glossary of terms and a list of acronyms are also included for the reader's convenience.

09 BIOMASS FUELS↗

Multiport Control with Partial Power Processing in Solid-State Transformer for PV, Storage, and Fast-Charging Electric Vehicle Integration

This article proposes a multiport control method to enable partial power processing (PPP) in a medium-voltage (MV) multiport solid-state transformer (SST). MV multiport SSTs are promising in integrating low-voltage DC sources or loads such as solar photovoltaic, energy storage, and electric vehicles into smart grids without bulky line-frequency transformers. Compared to voltage-source SST, current-source (CS) SST features single-stage isolated bidirectional AC/AC, AC/DC, or DC/DC conversion using an inductive DC link. For a multiport CS SST, it is revealed in this article that the PPP capability can be enabled through the proposed control without extra hardware, different from the case of voltage-source converters where special hardware architecture is required for the PPP. With the PPP, most power exchange between LV ports is processed by only a fraction of the entire conversion stage, leading to reduced DC-link current, volume, loss, and improved efficiency. The proposed multiport PPP control scheme is analyzed to verify the advantages across a wide voltage and power range against conventional full power processing (FPP) multiport control, using the soft-switching solid-state transformer (S4T) with reduced conduction loss as an example. Comparative experimental results based on a SiC three-port S4T prototype verify the effectiveness of the proposed PPP scheme against the FPP scheme under both steady state and dynamic conditions. Here, the DC-link current reduction is measured to be more than 36%. Significantly, the proposed multiport PPP control scheme is generic and applicable to any hard-switching or soft-switching CS SSTs without extra hardware.

14 SOLAR ENERGY↗

Redox flow batteries: a review

Redox flow batteries (RFBs) are enjoying a renaissance due to their ability to store large amounts of electrical energy relatively cheaply and efficiently. In this review, we examine the components of RFBs with a focus on understanding the underlying physical processes. The various transport and kinetic phenomena are discussed along with the most common redox couples.

30 DIRECT ENERGY CONVERSION↗

Survey of carbonization facilities for municipal solid waste treatment in Japan

The operations of carbonization facilities for municipal solid waste treatment in Japan were examined. Input waste, system processes, material flows, quality of char and its utilization, fuel and chemical consumption, control of facility emissions, and trouble areas in facility operation were investigated and analyzed. Although carbonization is a technically available thermochemical conversion method for municipal solid waste treatment, problems of energy efficiency and char utilization must be solved for carbonization to be competitive. Possible solutions include (1) optimizing the composition of input waste, treatment scale, organization of unit processes, operational methods, and quality and yield of char on the basis of analysis and feedback of long-term operating data of present operating facilities and (2) securing stable char demands by linking with local industries such as thermal electric power companies, iron manufacturing plants, and cement production plants.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗