Search NASA⌕ Search

SEARCH · Search NASA

Results for “engine friction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,034 records · Page 58

Effects of Pin Detached Space on Heat Transfer in a Rib Roughened Channel

An experimental study is performed to investigate the heat transfer characteristics and frictional losses in a rib roughened channel combined with detached pin-fins. The overall channel geometry (W=76.2 mm, E=25.4 mm) simulates an internal cooling passage of wide aspect ratio (3:1) in a gas turbine airfoil. With a given pin diameter, D=6.35 mm=[1/4]E, three different pin-fin height-to-diameter ratios, H/D=4, 3, and 2, were examined. Each of these three cases corresponds to a specific pin array geometry of detachment spacing (C) between the pin-tip and one of the endwalls, i.e., C/O=0, 1, 2, respectively. The rib height-to-channel height ratio is 0.0625. Two newly proposed cross ribs, namely the broken rib and full rib are evaluated in this effort. The broken ribs are positioned in between two consecutive rows of pin-fins, while the full ribs are fully extended adjacent to the pin-fins. The Reynolds number, based on the hydraulic diameter of the unobstructed cross section and the mean bulk velocity, ranges from 10,000 to 25,000. The experiment employs a hybrid technique based on transient liquid crystal imaging to obtain distributions of the local heat transfer coefficient over all of the participating surfaces, including the endwalls and all pin elements. The presence of ribs enhances local heat transfer coefficient on the endwall substantially by approximately 20% to 50% as compared to the neighboring endwall. In addition, affected by the rib geometry, which is a relatively low profile as compared to the overall height of the channel, the pressure loss seems to be insensitive to the presence of the ribs. However, from the overall heat transfer enhancement standpoint, the baseline cases (without ribs) outperform cases with broken ribs or full ribs.

42 ENGINEERING↗

RANS Based Methodology for Predicting the Influence of Leading Edge Erosion on Airfoil Performance

The impact of surface roughness on flows over aerodynamically designed surfaces is of interested in a number of different fields. It has long been known the surface roughness will likely accelerate the laminar- turbulent transition process by creating additional disturbances in the boundary layer. However, there are very few tools available to predict the effects surface roughness will have on boundary layer flow. There are numerous implications of the premature appearance of a turbulent boundary layer. Increases in local skin friction, boundary layer thickness, and turbulent mixing can impact global flow properties compounding the effects of surface roughness. With this motivation, an investigation into the effects of surface roughness on boundary layer transition has been conducted. The effort involved both an extensive experimental campaign, and the development of a high fidelity roughness model implemented in a R ANS solver. Vast a mounts of experimental data was generated at the Texas A&M Oran W. Nicks Low Speed Wind Tunnel for the calibration and validation of the roughness model described in this work, as well as future efforts. The present work focuses on the development of the computational model including a description of the calibration process. The primary methodology presented introduces a scalar field variable and associated transport equation that interacts with a correlation based transition model. The additional equation allows for non-local effects of surface roughness to be accounted for downstream of rough wall sections while maintaining a "local" formulation. The scalar field is determined through a boundary condition function that has been calibrated to flat plate cases with sand grain roughness. The model was initially tested on a NACA 0012 airfoil with roughness strips applied to the leading edge. Further calibration of the roughness model was performed using results from the companion experimental study on a NACA 63 3 -418 airfoil. The refined model demonstrates favorable agreement predicting changes to the transition location, as well as drag, for a number of different leading edge roughness configurations on the NACA 63 3 -418 airfoil. Additional tests were conducted on a thicker S814 airfoil, with similar roughness configurations to the NACA 63 3 -418. Simulations run with the roughness model compare favorably with the results obtained in the experimental study for both airfoils.

42 ENGINEERING↗

Engineering Overview of a Multidisciplinary HSCT Design Framework Using Medium-Fidelity Analysis Codes

An objective of the HPCC Program at NASA Langley has been to promote the use of advanced computing techniques to more rapidly solve the problem of multidisciplinary optimization of a supersonic transport configuration. As a result, a software system has been designed and is being implemented to integrate a set of existing discipline analysis codes, some of them CPU-intensive, into a distributed computational framework for the design of a High Speed Civil Transport (HSCT) configuration. The proposed paper will describe the engineering aspects of integrating these analysis codes and additional interface codes into an automated design system. The objective of the design problem is to optimize the aircraft weight for given mission conditions, range, and payload requirements, subject to aerodynamic, structural, and performance constraints. The design variables include both thicknesses of structural elements and geometric parameters that define the external aircraft shape. An optimization model has been adopted that uses the multidisciplinary analysis results and the derivatives of the solution with respect to the design variables to formulate a linearized model that provides input to the CONMIN optimization code, which outputs new values for the design variables. The analysis process begins by deriving the updated geometries and grids from the baseline geometries and grids using the new values for the design variables. This free-form deformation approach provides internal FEM (finite element method) grids that are consistent with aerodynamic surface grids. The next step involves using the derived FEM and section properties in a weights process to calculate detailed weights and the center of gravity location for specified flight conditions. The weights process computes the as-built weight, weight distribution, and weight sensitivities for given aircraft configurations at various mass cases. Currently, two mass cases are considered: cruise and gross take-off weight (GTOW). Weights information is obtained from correlations of data from three sources: 1) as-built initial structural and non-structural weights from an existing database, 2) theoretical FEM structural weights and sensitivities from Genesis, and 3) empirical as-built weight increments, non-structural weights, and weight sensitivities from FLOPS. For the aeroelastic analysis, a variable-fidelity aerodynamic analysis has been adopted. This approach uses infrequent CPU-intensive non-linear CFD to calculate a non-linear correction relative to a linear aero calculation for the same aerodynamic surface at an angle of attack that results in the same configuration lift. For efficiency, this nonlinear correction is applied after each subsequent linear aero solution during the iterations between the aerodynamic and structural analyses. Convergence is achieved when the vehicle shape being used for the aerodynamic calculations is consistent with the structural deformations caused by the aerodynamic loads. To make the structural analyses more efficient, a linearized structural deformation model has been adopted, in which a single stiffness matrix can be used to solve for the deformations under all the load conditions. Using the converged aerodynamic loads, a final set of structural analyses are performed to determine the stress distributions and the buckling conditions for constraint calculation. Performance constraints are obtained by running FLOPS using drag polars that are computed using results from non-linear corrections to the linear aero code plus several codes to provide drag increments due to skin friction, wave drag, and other miscellaneous drag contributions. The status of the integration effort will be presented in the proposed paper, and results will be provided that illustrate the degree of accuracy in the linearizations that have been employed.

Weston, R. P.↗

RCCS Testing with the Water-based NSTF: Year-1 Single-Phase Results

Under support from the Department of Energy (DOE) and the Office of Advanced Reactor Technologies (ART), a large scale test facility has been constructed to generate validation data for passive decay heat removal systems of advanced reactors. Located at Argonne National Laboratory, the Natural convection Shutdown heat removal Test Facility (NSTF) reflects key features of a ½ scale, water-based, Reactor Cavity Cooling System (RCCS). This report serves as a summary of the single-phase testing results obtained during the programs first year of matrix testing. An introduction to the high-level program objectives is first presented, followed by a brief summary of facility design, instrumentation, and control systems. Details of the NQA-1 driven test method are included, which govern the programs quality assurance requirements and provide a background for the testing strategy and procedures. Checkout activities, including verification of gross system mass and energy balances, heat loss quantification, and isothermal facility characterization, were performed early in the first year and results presented in this report. These tests have identified relevant facility characteristics such as K-factors, frictional pressure losses, parasitic heat loss rates, and transient heating response. Results are then presented from four accepted matrix tests where the facility established a steady-state, single-phase mode of flow operation. All matrix tests were performed with an identical top-level procedure: first initiating a heater power ramp to target levels, and then holding power levels constant until the facilities structural members and network piping reached thermal equilibrium. Upon obtaining stable thermal and hydraulic conditions, active cooling was initiated off of the bulk storage tank to maintain constant riser inlet temperatures of 30°C. This steady-state period was then held for a minimum required duration, at which point the heaters were ramped down and test concluded. The two baseline tests completed reflect conditions prototypic to the full scale plant at both normal operation, and design basis Depressurized Loss of Forced Cooling (DLOFC) conditions. These parameters are defined by full RCCS decay heat loads of 1.4 MWt and 2.1 MWt, which translate to NSTF scale thermal power levels of 34.4 kWt and 51.6 kWt, respectively. Two additional tests were also conducted, which repeated baseline cases but included modification by single parameter variations in decay heat load, or heater power, at 700 kWt, and 2.8 MWt. Finally, a scoping test was performed to demonstrate the facilities ability to operate in a two-phase mode of operation. The facility successfully operated for a 3-hour period at this mode, reaching peak inventory temperatures of 105°C and condensing approximately 50 gallons of boil-off inventory. The testing parameters for this demonstration were based off the design basis DLOFC condition, and will be the reference for new baseline cases as the program moves forward with two-phase matrix testing.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Influence of Tool Runout on Force Measurement During Internal Void Monitoring for Friction Stir Welding of 6061-T6 Aluminum

Abstract The goal of this research was to examine how altering the amount of friction stir tool eccentricity while controlling the amount of slant in the tool shoulder (drivers of oscillatory process forces) effects the generation of process force transients during sub-surface void interaction. The knowledge gained will help improve the accuracy of force-based void monitoring methods that have the potential to reduce the need for post-weld inspection. Process force transients during sub-surface void formation were examined for multiple tools with varying magnitudes of kinematic runout. The eccentric motion of the tool produced oscillations in the process forces at the tools rotational frequency that became distorted when features (flats) on the tool probe interacted with voided volumes, generating an amplitude in the force signals at three times the tool rotational frequency (for three-flat tools). A larger tool eccentricity generates a larger amplitude in the force signals at the tool’s rotational frequency that holds a larger potential to create a distortion during void interaction. It was determined that once void becomes large enough to produce an interaction that generates an amplitude at the third harmonic larger than 30% of the amplitude at the rotational frequency in a weld with no interaction (amplitude solely at rotational frequency), the trailing edge of the tool shoulder cannot fully consolidate the void, i.e., it will remain in the final weld. Additionally, once the void exceeds a certain size, the amplitudes of the third harmonics saturate at 70% of the amplitude at the rotational frequency during full consolidation. The interaction between the eccentric probe and sub-surface void was isolated by ensuring any geometric imperfection in the shoulder (slant) with respect to the rotational axis was removed. The results suggest that geometric imperfections (eccentricity and slant) with respect to the tool’s rotational axis must be known when developing a void monitoring method from force transients of this nature.

Engineering↗

Modeling the Effects of a Backward-Facing Step on Boundary-Layer Transition

We model transition to turbulence in a two-dimensional boundary layer downstream of a backward-facing step (BFS) along a flat plate. With the goal of evaluating the available engineering models for predicting the effects of step excrescences on the transition characteristics, two separate methodologies are used to monitor the streamwise shift in the transition onset location as the step height and the flow speed are varied across the range of a previously reported experiment involving step-height-to-local-displacement-thickness ratios of 0 < h/δ* < 1.6. Unlike the variable N -factor method from the previous literature, both of these methods are general in scope and do not involve any empirical correlations that are specific to step excrescences. The first of these techniques involves an N -factor method that directly accounts for the change in boundary-layer instability characteristics due to the step. Stability computations using the harmonic linearized Navier-Stokes equations (HLNSE), which fully account for the nonparallel-mean-flow effects close to the BFS, indicate that the measured transition locations at nearly all test conditions ( h/δ* < 1.3) correlate well with a computed N -factor of N tr = 7.6, demonstrating a successful stability-based transition criterion related to step excrescences. Linear stability theory, which does not account for nonparallel effects, demonstrates reasonable agreement with the HLNSE results, yielding good predictions for the overall trends, but predicts a somewhat earlier onset of transition than HLNSE. The other methodology used in this work involves transport-equation-based transition models. We first show that the Langtry-Menter y - Re θt transition model cannot accurately predict the location of transition onset for moderate BFS heights because it is unable to accurately account for the flow history effects. Along with the Langtry-Menter transition model, we also show the amplification factor transport model does not produce accurate transition locations for subsonic flow over steps even though it accounts for some flow history effects.

Transition↗

Modulation induced by very-large-scale motions on the inclination angle of wall-attached eddies: an atmospheric surface layer experiment

The forward leaning inclination angle, 𝛾, of coherent turbulent structures is a well-known feature of wall-bounded turbulent flows. Although invariant across friction Reynolds numbers within the range 𝑅𝑒 𝜏 =10 3 −10 6 , 𝛾 can vary significantly across turbulent scales within a high-Reynolds-number flow. Very-large-scale motions (VLSMs) are known to induce significant changes in the instantaneous shear profile, which is a conditioning event that could trigger variability in the inclination angle of smaller coherent turbulent structures. Although this aspect has been extensively studied via numerical and laboratory experiments, few studies have explored this feature for a very-high-Reynolds-number atmospheric flow. In this work, the inclination angle of turbulent structures within the atmospheric surface layer at a very high Reynolds number (𝑅𝑒 𝜏 =7.9 ×10 5 ) is investigated by deploying a scanning Doppler light detection and ranging and a super large particle image velocimetry (SLPIV) apparatus. The inclination angle of wall-attached eddies is inferred either from the two-point correlation of streamwise velocity (𝛾 =41.1∘) or with a scale-dependent approach through the spectral linear stochastic estimator (SLSE). The SLSE (and, thus, the scale-dependent inclination angle) is conditionally evaluated based on the high- and low-momentum events induced by VLSMs, both in the streamwise (𝑢′𝑉𝐿𝑆𝑀) and in the vertical (𝑤′ 𝑉𝐿𝑆𝑀) velocity components. As a result, lower inclination angles (𝛾 =30° −50°) are found for 𝑢$^{'}_{VLSM}$ >0 (𝑤$^{'}_{VLSM}$ <0), while higher values (50° −85°) are ascribed to 𝑢$^{'}_{VLSM}$ <0 (𝑤$^{'}_{VLSM}$ >0). This result emphasises the primary role that VLSMs play in shaping the wall-attached eddy geometry, which, in turn, is crucial to determine the Reynolds stress balance within the wall-attached eddy range.

42 ENGINEERING↗

Data for "Constitutive Down-Regulation of Liguleless Alleles in Sorghum Drives Increased Productivity and Water Use Efficiency"

Plant architecture influences the microenvironment throughout the canopy layer. Plants with a more erect leaf architecture allow for an increase in planting densities and allow more light to reach lower canopy leaves. This is predicted to increase crop carbon assimilation. Frictional resistance to wind reduces air movement in the lower canopy, resulting in higher humidity. By increasing the proportion of canopy photosynthesis in the more humid lower canopy, gains in the efficiency of water use might be expected, although this may be slightly offset by the more open erectophile form canopy. An anatomical feature in members of the Poaceae family that impacts leaf angle is the articulated junction of the sheath and blade, which also bares the ligule and auricles. Mutants, which lack ligules and auricles, show no articulation at this junction, resulting in leaves that are near vertical. In maize, these phenotypes termed liguleless result from null mutations of genes: ZmLG1 (Zm00001eb67740) and ZmLG2 (Zm00001eb147220). In sorghum, SbiRTx430.06G264300 (SbLG1) and SbiRTx430.03G392300 (SbLG2) are annotated as the respective maize homologues. A hair-pin element designed to down-regulate both SbLG1 and SbLG2 was introduced into the grain sorghum genotype RTx430. Derived transgenic events harbouring the hair-pin failed to develop ligules and displayed reduced leaf angles to the vertical, but less vertical than in null mutations. Under field settings, plots sown with these sorghum events having an erect architecture phenotype displayed an increase in photosynthesis in lower canopy levels, which led to increases in above-ground biomass and seed yield, without an increase in water use.

Genome Engineering↗