Search NASA⌕ Search

SEARCH · Search NASA

Results for “numerical diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Inlet Flow Control and Prediction Technologies for Embedded Propulsion Systems

Fail-safe, hybrid, flow control (HFC) is a promising technology for meeting high-speed cruise efficiency, low-noise signature, and reduced fuel-burn goals for future, Hybrid-Wing-Body (HWB) aircraft with embedded engines. This report details the development of HFC technology that enables improved inlet performance in HWB vehicles with highly integrated inlets and embedded engines without adversely affecting vehicle performance. In addition, new test techniques for evaluating Boundary-Layer-Ingesting (BLI)-inlet flow-control technologies developed and demonstrated through this program are documented, including the ability to generate a BLI-like inlet-entrance flow in a direct-connect, wind-tunnel facility, as well as, the use of D-optimal, statistically designed experiments to optimize test efficiency and enable interpretation of results. Validated improvements in numerical analysis tools and methods accomplished through this program are also documented, including Reynolds-Averaged Navier-Stokes CFD simulations of steady-state flow physics for baseline, BLI-inlet diffuser flow, as well as, that created by flow-control devices. Finally, numerical methods were employed in a ground-breaking attempt to directly simulate dynamic distortion. The advances in inlet technologies and prediction tools will help to meet and exceed "N+2" project goals for future HWB aircraft.

McMillan, Michelle L.↗

Numerical studies of transient gain reduction process in a multi-wire proportional chamber

A gain reduction process caused by successive beam irradiation in a multi-wire proportional chamber was numerically investigated to clarify the relations between the gas gain variation and the ion density distribution. A numerical code was developed based on a two-dimensional drift-diffusion model in order to evaluate the ion and electron density distributions and the electric field variation caused by the space charge effect. In order to consider the gain reduction process which occurs under the high rate and successive irradiation, the simulations were performed for the time period of {approx}10-100 {mu}s, which is much longer than the time required for ions to travel from an anode to a cathode. The numerical simulation results showed that for the low gas gain regime of {approx}10, quasi-stationary density distribution of the ions was formed by the high-rate beams of {approx}10{sup 8}- 10{sup 10} particles per second, and that the transient variation of the gas gain became constant after establishment of the quasi-stationary ion density distributions.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The Numerical Computation of Clear-Sky Transmittance and Reflectance of Solar Radiation for the Modeling of PV System Performance

Modeling of photovoltaics (PV) system performance requires numerical computation of plane-of-array (POA) irradiances that are influenced by atmospheric absorption and scattering. Clear-sky transmittance and reflectance of diffuse irradiance are essential for the understanding of solar radiation related to multiple reflection between land surface and clouds. This study analytically solves the radiative transfer equation for clear-sky conditions and numerically computes the transmittance and reflectance of diffuse irradiance as functions of the optical thickness of the atmosphere. The computation will be implemented in all-sky radiative transfer models to improve their computational efficiency.

14 SOLAR ENERGY↗

Fire Suppression in Low Gravity Using a Cup Burner

Longer duration missions to the moon, to Mars, and on the International Space Station increase the likelihood of accidental fires. The goal of the present investigation is to: (1) understand the physical and chemical processes of fire suppression in various gravity and O2 levels simulating spacecraft, Mars, and moon missions; (2) provide rigorous testing of numerical models, which include detailed combustion-suppression chemistry and radiation sub-models; and (3) provide basic research results useful for advances in space fire safety technology, including new fire-extinguishing agents and approaches.The structure and extinguishment of enclosed, laminar, methane-air co-flow diffusion flames formed on a cup burner have been studied experimentally and numerically using various fire-extinguishing agents (CO2, N2, He, Ar, CF3H, and Fe(CO)5). The experiments involve both 1g laboratory testing and low-g testing (in drop towers and the KC-135 aircraft). The computation uses a direct numerical simulation with detailed chemistry and radiative heat-loss models. An agent was introduced into a low-speed coflowing oxidizing stream until extinguishment occurred under a fixed minimal fuel velocity, and thus, the extinguishing agent concentrations were determined. The extinguishment of cup-burner flames, which resemble real fires, occurred via a blowoff process (in which the flame base drifted downstream) rather than the global extinction phenomenon typical of counterflow diffusion flames. The computation revealed that the peak reactivity spot (the reaction kernel) formed in the flame base was responsible for attachment and blowoff of the trailing diffusion flame. Furthermore, the buoyancy-induced flame flickering in 1g and thermal and transport properties of the agents affected the flame extinguishment limits.

Takahashi, Fumiaki↗

Fire Suppression in Low Gravity Using a Cup Burner

Longer duration missions to the moon, to Mars, and on the International Space Station increase the likelihood of accidental fires. The goal of the present investigation is to: (1) understand the physical and chemical processes of fire suppression in various gravity and O2 levels simulating spacecraft, Mars, and moon missions; (2) provide rigorous testing of numerical models, which include detailed combustion suppression chemistry and radiation sub-models; and (3) provide basic research results useful for advances in space fire safety technology, including new fire-extinguishing agents and approaches. The structure and extinguishment of enclosed, laminar, methane-air co-flow diffusion flames formed on a cup burner have been studied experimentally and numerically using various fire-extinguishing agents (CO2, N2, He, Ar, CF3H, and Fe(CO)5). The experiments involve both 1g laboratory testing and low-g testing (in drop towers and the KC-135 aircraft). The computation uses a direct numerical simulation with detailed chemistry and radiative heat-loss models. An agent was introduced into a low-speed coflowing oxidizing stream until extinguishment occurred under a fixed minimal fuel velocity, and thus, the extinguishing agent concentrations were determined. The extinguishment of cup-burner flames, which resemble real fires, occurred via a blowoff process (in which the flame base drifted downstream) rather than the global extinction phenomenon typical of counterflow diffusion flames. The computation revealed that the peak reactivity spot (the reaction kernel) formed in the flame base was responsible for attachment and blowoff of the trailing diffusion flame. Furthermore, the buoyancy-induced flame flickering in 1g and thermal and transport properties of the agents affected the flame extinguishment limits.

Takahashi, Fumiaki↗

Discontinuous Galerkin methods for plasma physics in the scrape-off layer of tokamaks

A new parallel discontinuous Galerkin solver, called ArcOn, is developed to describe the intermittent turbulent transport of filamentary blobs in the scrape-off layer (SOL) of fusion plasma. The model is comprised of an elliptic subsystem coupled to two convection-dominated reaction–diffusion–convection equations. Upwinding is used for a class of numerical fluxes developed to accommodate cross product driven convection, and the elliptic solver uses SIPG, NIPG, IIPG, Brezzi, and Bassi–Rebay fluxes to formulate the stiffness matrix. A novel entropy sensor is developed for this system, designed for a space–time varying artificial diffusion/viscosity regularization algorithm. Some numerical experiments are performed to show convergence order on manufactured solutions, regularization of blob/streamer dynamics in the SOL given unstable parameterizations, long-time stability of modon (or dipole drift vortex) solutions arising in simulations of drift-wave turbulence, and finally the formation of edge mode turbulence in the scrape-off layer under turbulent saturation conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Flow regimes for fluid injection into a confined porous medium

We report theoretical and numerical studies of the flow behaviour when a fluid is injected into a confined porous medium saturated with another fluid of different density and viscosity. For a two-dimensional configuration with point source injection, a nonlinear convection–diffusion equation is derived to describe the time evolution of the fluid–fluid interface. In the early time period, the fluid motion is mainly driven by the buoyancy force and the governing equation is reduced to a nonlinear diffusion equation with a well-known self-similar solution. In the late time period, the fluid flow is mainly driven by the injection, and the governing equation is approximated by a nonlinear hyperbolic equation that determines the global spreading rate; a shock solution is obtained when the injected fluid is more viscous than the displaced fluid, whereas a rarefaction wave solution is found when the injected fluid is less viscous. In the late time period, we also obtain analytical solutions including the diffusive term associated with the buoyancy effects (for an injected fluid with a viscosity higher than or equal to that of the displaced fluid), which provide the structure of the moving front. Numerical simulations of the convection–diffusion equation are performed; the various analytical solutions are verified as appropriate asymptotic limits, and the transition processes between the individual limits are demonstrated.

58 GEOSCIENCES↗

Improving Solution Accuracy and Convergence for Stochastic Physics Parameterizations with Colored Noise

Stochastic parameterizations are used in numerical weather prediction and climate modeling to help capture the uncertainty in the simulations and improve their statistical properties. Convergence issues can arise when time integration methods originally developed for deterministic differential equations are applied naively to stochastic problems. In previous studies, it has been demonstrated that a correction term, known in stochastic analysis as the Itô correction, can help improve solution accuracy for various deterministic numerical schemes and ensure convergence to the physically relevant solution without substantial computational overhead. The usual formulation of the Itô correction is valid only when the stochasticity is represented by white noise. In this study, a generalized formulation of the Itô correction is derived for noises of any color. The formulation is applied to a test problem described by an advection–diffusion equation forced with a spectrum of fast processes. We present numerical results for cases with both constant and spatially varying advection velocities to show that, for the same time step sizes, the introduction of the generalized Itô correction helps to substantially reduce time integration error and significantly improve the convergence rate of the numerical solutions when the forcing term in the governing equation is rough (fast varying); alternatively, for the same target accuracy, the generalized Itô correction allows for the use of significantly longer time steps and, hence, helps to reduce the computational cost of the numerical simulation.

54 ENVIRONMENTAL SCIENCES↗

NUMERICAL STUDY OF THE LONGITUDINALLY ASYMMETRIC DISTRIBUTION OF SOLAR ENERGETIC PARTICLES IN THE HELIOSPHERE

Solar energetic particles (SEPs) affect the solar–terrestrial space environment and are very important to space weather research. In this work, we numerically investigate the transport processes of SEPs in the three-dimensional interplanetary magnetic field, with an emphasis on the longitudinal distribution of SEPs in the heliosphere. We confirm our previous finding that there exists an east–west longitudinal asymmetry in the SEP intensities, i.e., with the same longitude separations between the solar source centers and the magnetic footpoint of the observer, the fluxes of SEP events originating from solar sources located on the eastern side of the nominal magnetic footpoint of the observer are systematically larger than those of the SEP events originating from sources located on the western side. We discuss the formation mechanism of this phenomenon, and conclude that the longitudinally asymmetric distribution of SEPs results from the east–west azimuthal asymmetry in the topology of the heliospheric magnetic field as well as the effects of perpendicular diffusion on the transport of SEPs in the heliosphere. Our results will be valuable to understanding Sun–Earth relations and useful for space weather forecasting.

79 ASTRONOMY AND ASTROPHYSICS↗

Numerical Simulations of Orographic Convection across Multiple Gray Zones

Idealized simulations are used to determine the sensitivity of moist orographic convection to horizontal grid spacing Δ h . In simulated mechanically (MECH) and thermally (THERM) forced convection over an isolated ridge, Δ h is varied systematically over both the deep-convection (Δ h ~ 10 –1 km) and turbulence (Δ h ~ 1 km–100 m) gray zones. To aid physical interpretation, a new parcel-based bulk entrainment/detrainment diagnosis for horizontally heterogeneous flows is developed. Within the deep-convection gray zone, the Δ h sensitivity is dominated by differences in parameterized versus explicit convection; the former initiates convection too far upstream of the ridge (MECH) and too early in the diurnal heating cycle (THERM). These errors stem in part from a large underprediction of parameterized entrainment and detrainment. Within the turbulence gray zone, sensitivities to Δh arise from the representation of both subcloud- and cloud-layer turbulence. As Δ h is decreased, MECH exhibits stronger cloud-layer entrainment to enhance the convective mass flux M co , while THERM exhibits stronger detrainment to suppress Mco and delay convection initiation. The latter is reinforced by increased subcloud turbulence at smaller Δ h , which leads to drying and diffusion of the central updraft responsible for initiating moist convection. Numerical convergence to a robust solution occurs only in THERM, which develops a fully turbulent flow with a resolved inertial subrange (for Δ h ≤ 250 m). In MECH, by contrast, turbulent transition occurs within the orographic cloud, the details of which depend on both physical location and Δ h .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A localized artificial diffusivity method to simulate compressible multiphase flows using the stiffened gas equation of state: A localized artificial diffusivity method to simulate compressible multiphase flows using the stiffened gas equation of state

The development of numerical approaches to perform direct numerical simulations of compressible multiphase flows has been an active field of research for several years. Proper treatment of fluid interfaces is crucial as important physics occur in this infinitesimally small region. Furthermore, the compressibility of the fluid requires proper treatment of discontinuities. Artificial diffusivity is among a number of methods widely used for compressible flows. This study develops a general form of consistent artificial diffusion fluxes and extends the localized artificial diffusivity method for high-order central schemes to solve multiphase flows with an interface-capturing method. These fluxes ensure an oscillation-free interface for pressure, velocity, and temperature without employing a sharpening technique. Moreover, the high-order representation of all scales in the flow helps capture the wide range of instabilities inherent in these flows. The goal is to develop an approach capable of performing high-fidelity simulations supported by physics-driven validation. lastly, this is achieved by solving the five-equation model with the stiffened-gas equation of state using the proposed method for multicomponent and multiphase flows on a variety of 1D and 2D problems.

42 ENGINEERING↗

Variations of the cosmic-ray flux with time

The physical foundations of the modulation of the galactic cosmic ray flux by the sun are reviewed and related to heliospheric structure and dynamics. The basic physical effects - diffusion, convection, adiabatic cooling and drifts - are evaluated and shown to be all important. The results of numerical models are briefly presented and compared with observations. Present-day modulation is shown to reflect the combination of diffusion-convection effects and drift effects. The Maunder minimum is conjectured to be a period when a quiet sun and smooth solar wind resulted in the dominance of drift effects.

Jokipii, J. R.↗

An efficient reconstruction algorithm for diffusion on triangular grids using the nodal discontinuous Galerkin method

High-energy-density (HED) hydrodynamics studies such as those relevant to inertial confinement fusion and astrophysics require highly disparate densities, temperatures, viscosities, and other diffusion parameters over relatively short spatial scales. This presents a challenge for high-order accurate methods to effectively resolve the hydrodynamics at these scales, particularly in the presence of highly disparate diffusion. A significant volume of engineering and physics applications use an unstructured discontinuous Galerkin (DG) method developed based on the finite element mesh generation and algorithmic framework. This work discusses the application of an affine reconstructed nodal DG method for unstructured grids of triangles. Solving the diffusion terms in the DG method is non-trivial due to the solution representations being piecewise continuous. Hence, the diffusive flux is not defined on the interface of elements. The proposed numerical approach reconstructs a smooth solution in a parallelogram that is enclosed by the quadrilateral formed by two adjacent triangle elements. The interface between these two triangles is the diagonal of the enclosed parallelogram. Similar to triangles, the mapping of parallelograms from a physical domain to a reference domain is an affine mapping, which is necessary for an accurate and efficient implementation of the numerical algorithm. Thus, all computations can still be performed on the reference domain, which promotes efficiency in computation and storage. This reconstruction does not make assumptions on choice of polynomial basis. Reconstructed DG algorithms have previously been developed for modal implementations of the convection–diffusion equations. However, to the best of the authors’ knowledge, this is the first practical guideline that has been proposed for applying the reconstructed algorithm on a nodal discontinuous Galerkin method with a focus on accuracy and efficiency. As a result, the algorithm is demonstrated on a number of benchmark cases as well as a challenging substantive problem in HED hydrodynamics with highly disparate diffusion parameters.

Computational efficiency↗

Binary Oscillatory Crossflow Electrophoresis

Electrophoresis has long been recognized as an effective analytic technique for the separation of proteins and other charged species, however attempts at scaling up to accommodate commercial volumes have met with limited success. In this report we describe a novel electrophoretic separation technique - Binary Oscillatory Crossflow Electrophoresis (BOCE). Numerical simulations indicate that the technique has the potential for preparative scale throughputs with high resolution, while simultaneously avoiding many problems common to conventional electrophoresis. The technique utilizes the interaction of an oscillatory electric field and a transverse oscillatory shear flow to create an active binary filter for the separation of charged protein species. An oscillatory electric field is applied across the narrow gap of a rectangular channel inducing a periodic motion of charged protein species. The amplitude of this motion depends on the dimensionless electrophoretic mobility, alpha = E(sub o)mu/(omega)d, where E(sub o) is the amplitude of the electric field oscillations, mu is the dimensional mobility, omega is the angular frequency of oscillation and d is the channel gap width. An oscillatory shear flow is induced along the length of the channel resulting in the separation of species with different mobilities. We present a model that predicts the oscillatory behavior of charged species and allows estimation of both the magnitude of the induced convective velocity and the effective diffusivity as a function of a in infinitely long channels. Numerical results indicate that in addition to the mobility dependence, the steady state behavior of solute species may be strongly affected by oscillating fluid into and out of the active electric field region at the ends of the cell. The effect is most pronounced using time dependent shear flows of the same frequency (cos((omega)t)) flow mode) as the electric field oscillations. Under such conditions, experiments indicate that solute is drawn into the cell from reservoirs at both ends of the cell leading to a large mass build up. As a consequence, any initially induced mass flux will vanish after short times. This effect was not captured by the infinite channel model and hence numerical and experimental results deviated significantly. The revised model including finite cell lengths and reservoir volumes allowed quantitative predictions of the time history of the concentration profile throughout the system. This latter model accurately describes the fluxes observed for both oscillatory flow modes in experiments using single protein species. Based on the results obtained from research funded under NASA grant NAG-8-1080.S, we conclude that binary separations are not possible using purely oscillatory flow modes because of end effects associated with the cos((omega)t) mode. Our research shows, however, that a combination of cos(2(omega)t) and steady flow should lead to efficient separation free of end effects. This possibility is currently under investigation.

Molloy, Richard F.↗

Short efficient ejector systems

A research program was conducted to improve the performance of low pressure ratio ejector systems. The results show that short, efficient ejectors operating at nearly ideal performance are possible through the use of forced mixer lobes. Forced mixer lobes generate large scale axial vorticity which results in rapid mixing and improved diffuser performance. Ejector testing was conducted using both an ejector wind tunnel. Numerous mixer lobe variations were tested to develop lobe design guidelines. The improved performance of mixer-ejectors is presented over a range of operating conditions. Results of mixer lobe angle, penetration, and alignment are presented. Lobe angles of up to 25 deg, coupled with diffuser wall angles over 20 deg, operate without separation, allowing efficient, short ejector systems. Both warm and cold flow test results are presented. Temperature similarity expressions previously developed are further formulated and verified.

Presz, Walter M., Jr.↗

EFFECTS OF PERPENDICULAR DIFFUSION ON ENERGETIC PARTICLES ACCELERATED BY THE INTERPLANETARY CORONAL MASS EJECTION SHOCK

In this work, based on a numerical solution of the focused transport equation, we obtained the intensity and anisotropy time profiles of solar energetic particles (SEPs) accelerated by an interplanetary shock in the three-dimensional Parker magnetic field. The shock is treated as a moving source of energetic particles with an assumed particle distribution function. We computed the time profiles of particle flux and anisotropy as measured by an observer at 1 AU, equatorial plane, and various longitudes with respect to the shock propagation direction. With perpendicular diffusion, energetic particles can cross magnetic field lines. Particles may be detected before the observer's field line is connected to the shock. After the observer's field line breaks from the shock front, the observer still can see more particles are injected into its field line. Our simulations show that the particle onset time, peak time, peak intensity, decay rate, and duration of SEP event could be significantly influenced by the effect of perpendicular diffusion. The anisotropy with perpendicular diffusion is almost the same as that without perpendicular diffusion, but there is an obvious difference at the moment when the observer's field line begins to be connected to the shock.

79 ASTRONOMY AND ASTROPHYSICS↗

Communication: Polymer entanglement dynamics: Role of attractive interactions

The coupled dynamics of entangled polymers, which span broad time and length scales, govern their unique viscoelastic properties. To follow chain mobility by numerical simulations from the intermediate Rouse and reptation regimes to the late time diffusive regime, highly coarse grained models with purely repulsive interactions between monomers are widely used since they are computationally the most efficient. In this paper, using large scale molecular dynamics simulations, the effect of including the attractive interaction between monomers on the dynamics of entangled polymer melts is explored for the first time over a wide temperature range. Attractive interactions have little effect on the local packing for all temperatures T and on the chain mobility for T higher than about twice the glass transition T g . Finally, these results, across a broad range of molecular weight, show that to study the dynamics of entangled polymer melts, the interactions can be treated as pure repulsive, confirming a posteriori the validity of previous studies and opening the way to new large scale numerical simulations.

36 MATERIALS SCIENCE↗

Alpha particles diffusion due to charge changes

Alpha particles diffusion due to charge changes in a magnetized plasma is studied. Analytical calculations and numerical simulations are employed to show that this process can be very important in the pedestal-edge-SOL regions. This is the first study that presents clear evidence of the importance of atomic processes on the diffusion of alpha particles. A simple 1D model that includes inelastic collisions with plasma species, “cold” neutrals, and partially ionized species was employed. The code, which follows the exact particle orbits and includes the effect of inelastic collisions via a Monte Carlo type random process, runs on a graphic processor unit (GPU). The analytical and numerical results show excellent agreement when a uniform background (plasma and cold species) is assumed. The simulations also show that the gradients in the density of the plasma and cold species, which are large and opposite in the edge region, produce an inward flux of alpha particles. Calculations of the alpha particles flux reaching the walls or divertor plates should include these processes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗