Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Alternative methods for calculating sensitivity of optimized designs to problem parameters

Optimum sensitivity is defined as the derivative of the optimum design with respect to some problem parameter, P. The problem parameter is usually fixed during optimization, but may be changed later. Thus, optimum sensitivity is used to estimate the effect of changes in loads, materials or constraint bounds on the design without expensive re-optimization. Here, the general topic of optimum sensitivity is discussed, available methods identified, examples given, and the difficulties encountered in calculating this information in nonlinear constrained optimization are identified.

Vanderplaats, G. N.↗

SU-E-T-583: Optimizing the MLC Model Parameters for IMRT in the RayStation Treatment Planning System

Purpose: To optimize the MLC model parameters for IMRT in the RayStation v.4.0 planning system and for a Varian C-series Linac with a 120-leaf Millennium MLC. Methods: The RayStation treatment planning system models rounded leaf-end MLC with the following parameters: average transmission, leaf-tip width, tongue-and-groove, and position offset. The position offset was provided by Varian. The leaf-tip width was iteratively evaluated by comparing computed and measured transverse dose profiles of MLC-defined fields at dmax in water. The profile comparison was also used to verify the MLC position offset. The transmission factor and leaf tongue width were derived iteratively by optimizing five clinical patient IMRT QA Results: brain, lung, pancreas, head-and-neck (HN), and prostate. The HN and prostate cases involved splitting fields. Verifications were performed with Mapcheck2 measurements and Monte Carlo calculations. Finally, the MLC model was validated using five test IMRT cases from the AAPM TG119 report. Absolute gamma analyses (3mm/3% and 2mm/2%) were applied. In addition, computed output factors for MLC-defined small fields (2×2, 3×3, 4×4, 6×6cm) of both 6MV and 18MV were compared to those measured by the Radiological Physics Center (RPC). Results: Both 6MV and 18MV models were determined to have the same MLC parameters: 2.5% transmission, tongue-and-groove 0.05cm, and leaftip 0.3cm. IMRT QA analysis for five cases in TG119 resulted in a 100% passing rate with 3mm/3% gamma analysis for 6MV, and >97.5% for 18MV. With 2mm/2% gamma analysis, the passing rate was >94.6% for 6MV and >90.9% for 18MV. The difference between computed output factors in RayStation and RPC measurements was less than 2% for all MLCdefined fields, which meets the RPC's acceptance criterion. Conclusion: The rounded leaf-end MLC model in RayStation 4.0 planning system was verified and IMRT commissioning was clinically acceptable. The IMRT commissioning was well validated using guidance from the AAPMTG119 protocol.

60 APPLIED LIFE SCIENCES↗

Simultaneous Optimization of Crystal Plasticity Hardening Parameters

Crystal plasticity models relate macroscopic deformation behavior to the evolution of slip systems strength, but their parameterization is often non-unique, with multiple parameter sets being able to describe the same macroscopic behavior. To address this issue, the present work adopts a Bayesian optimization framework for the parameterization of face-centered cubic plasticity models while simultaneously considering multiple experimental datasets from the literature. For single crystal Cu, parameter optimization was guided by the tensile stress–strain curves along several crystallographic orientations, with an adequate fit being found for five orientations at once. While additional parameters allowed for the consideration of more physical mechanisms, like different slip system interaction strengths or misorientations inherent to the experimental data, the extra dimensionality was found to limit the efficiency of the global minimization procedure. For polycrystalline Ni, multiple grain sizes were considered together in a representative polycrystalline model, with the optimization able to reconcile the model with the data for three grain sizes at once. As meaningful interpretation of parameters relies on the uniqueness of their values, incorporating multiple datasets into this discerning parameterization procedure enables more robust prediction and application of crystal plasticity models.

36 MATERIALS SCIENCE↗

Optimizing Perovskite Thin‐Film Parameter Spaces with Machine Learning‐Guided Robotic Platform for High‐Performance Perovskite Solar Cells

Abstract Simultaneously optimizing the processing parameters of functional thin films remains a challenge. The design and utilization of a fully automated platform called SPINBOT is presented for the engineering of solution‐processed functional thin films. The SPINBOT is capable of performing experiments with high sampling variability through the unsupervised processing of hundreds of substrates with exceptional experimental control. Through the iterative optimization process enabled by the Bayesian optimization (BO) algorithm, the SPINBOT explores an intricate parameter space, continuously improving the quality and reproducibility of the produced thin films. This machine learning (ML)‐guided reliable SPINBOT platform enables the acceleration of the optimization process of perovskite solar cells via a simple photoluminescence characterization of films. As a result, this study arrives at an optimal film that, when processed into a solar cell in an ambient atmosphere, immediately yields a champion power conversion efficiency (PCE) of 21.6% with satisfactory performance reproducibility. The unsealed devices retain 90% of their initial efficiency after 1100 h of continuous operation at 60–65 °C under metal‐halide lamps. It is anticipated that the integration of robotic platforms with the intelligent algorithm will facilitate the widespread adoption of effective autonomous experimentation to address the evolving needs and constraints within the materials science research community.

14 SOLAR ENERGY↗

Modeling Phenological Controls on Carbon Dynamics in Dryland Sagebrush Ecosystems

Dryland ecosystems play an important role in determining how precipitation anomalies affect terrestrial carbon fluxes at regional to global scales. Thus, to understand how climate change may affect the global carbon cycle, we must also be able to understand and model its effects on dryland vegetation. Dynamic Global Vegetation Models (DGVMs) are an important tool for modeling ecosystem dynamics, but they often struggle to reproduce seasonal patterns of plant productivity. Because the phenological niche of many plant species is linked to both total productivity and competitive interactions with other plants, errors in how process-based models represent phenology hinder our ability to predict climate change impacts. This may be particularly problematic in dryland ecosystems where many species have developed a complex phenology in response to seasonal variability in both moisture and temperature. Here, we examine how uncertainty in key parameters as well as the structure of existing phenology routines affect the ability of a DGVM to match seasonal patterns of leaf area index (LAI) and gross primary productivity (GPP) across a temperature and precipitation gradient. First, we optimized model parameters using a combination of site-level eddy covariance data and remotely-sensed LAI data. Second, we modified the model to include a semi-deciduous phenology type and added flexibility to the representation of grass phenology. While optimizing parameters reduced model bias, the largest gains in model performance were associated with the development of our new representation of phenology. This modified model was able to better capture seasonal patterns of both leaf area index (R(exp 2) = 0.75) and gross primary productivity (R(exp 2) = 0.84), though its ability to estimate total annual GPP depended on using eddy covariance data for optimization. The new model also resulted in a more realistic outcome of modeled competition between grass and shrubs. These findings demonstrate the importance of improving how DGVMs represent phenology in order to accurately forecast climate change impacts in dryland ecosystems.

Ecosystem model↗

Analytical gradient-based optimization of CALPHAD model parameters

The calibration of CALPHAD (CALculation of PHAse Diagrams) models involves the solution of a very challenging high-dimensional multiobjective optimization problem. Traditional approaches to parameter fitting predominantly rely on gradient-free methods, which while robust, are computationally inefficient and often scale poorly with model complexity. In this work, we introduce and demonstrate a generalizable framework for analytic gradient-based optimization of the parameters of the CALPHAD model enabled by the recently formalized Jansson derivative technique. This method allows for efficient evaluation of gradients of thermodynamic properties at equilibrium with respect to model parameters, even in the presence of arbitrarily complex internal degrees of freedom. Leveraging these semi-analytic gradients, we employ the conjugate gradient (CG) method to optimize thermodynamic model parameters for four binary alloy systems: Cu-Mg, Fe-Ni, Cr-Ni, and Cr-Fe. Across all systems, CG achieves comparable or superior optimality relative to Bayesian ensemble Markov Chain Monte Carlo (MCMC) with improvements in computational efficiency ranging from one to three orders of magnitude. Furthermore, our results establish a new paradigm for CALPHAD assessments in which high fidelity data-rich model calibration becomes tractable using deterministic gradient-informed algorithms.

CALPHAD↗

Design of optimal probing signals for vector parameter estimation.

In the design of optimal inputs or probing signals for parameter estimation, it is more natural to consider functions of the Fisher information matrix as the criterion of optimality instead of some function of the error covariance matrix. The input which maximizes the Fisher information measure for efficient estimation of a scalar parameter also provides the minimum error variance. The information is thus a logical choice for the optimality criterion in scalar problems. No such obvious choice is apparent for vector parameter estimation. A number of performance measures are examined and compared in the present study, and a useful criterion is selected. The design of an optimal probing signal using this criterion is shown to be equivalent to an optimal control problem in which certain equality constraints must be satisfied. This problem may be solved by conventional techniques of deterministic or stochastic optimal control.

Nahi, N. E.↗

Real-Time Nitrate Ion Monitoring with Poly(3,4-ethylenedioxythiophene) (PEDOT) Materials

Nitrate (NO 3 ) pollution in groundwater, caused by various factors both natural and synthetic, contributes to the decline of human health and well-being. Current techniques used for nitrate detection include spectroscopic, electrochemical, chromatography, and capillary electrophoresis. It is highly desired to develop a simple cost-effective alternative to these complex methods for nitrate detection. Therefore, a real-time poly (3,4-ethylenedioxythiophene) (PEDOT)-based sensor for nitrate ion detection via electrical property change is introduced in this study. Vapor phase polymerization (VPP) is used to create a polymer thin film. Variations in specific parameters during the process are tested and compared to develop new insights into PEDOT sensitivity towards nitrate ions. Through this study, the optimal fabrication parameters that produce a sensor with the highest sensitivity toward nitrate ions are determined. With the optimized parameters, the electrical resistance response of the sensor to 1000 ppm nitrate solution is 41.79%. Furthermore, the sensors can detect nitrate ranging from 1 ppm to 1000 ppm. The proposed sensor demonstrates excellent potential to detect the overabundance of nitrate ions in aqueous solutions in real time.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Autopilot for frequency-modulation atomic force microscopy

One of the most challenging aspects of operating an atomic force microscope (AFM) is finding optimal feedback parameters. This statement applies particularly to frequency-modulation AFM (FM-AFM), which utilizes three feedback loops to control the cantilever excitation amplitude, cantilever excitation frequency, and z-piezo extension. These loops are regulated by a set of feedback parameters, tuned by the user to optimize stability, sensitivity, and noise in the imaging process. Optimization of these parameters is difficult due to the coupling between the frequency and z-piezo feedback loops by the non-linear tip-sample interaction. Four proportional-integral (PI) parameters and two lock-in parameters regulating these loops require simultaneous optimization in the presence of a varying unknown tip-sample coupling. Presently, this optimization is done manually in a tedious process of trial and error. Here, we report on the development and implementation of an algorithm that computes the control parameters automatically. The algorithm reads the unperturbed cantilever resonance frequency, its quality factor, and the z-piezo driving signal power spectral density. It analyzes the poles and zeros of the total closed loop transfer function, extracts the unknown tip-sample transfer function, and finds four PI parameters and two lock-in parameters for the frequency and z-piezo control loops that optimize the bandwidth and step response of the total system. Implementation of the algorithm in a home-built AFM shows that the calculated parameters are consistently excellent and rarely require further tweaking by the user. The new algorithm saves the precious time of experienced users, facilitates utilization of FM-AFM by casual users, and removes the main hurdle on the way to fully automated FM-AFM.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Parameterization and sensitivity analysis of a process‐based terrestrial ecosystem model using adjoint method

Abstract We developed an adjoint version of a process‐based biogeochemistry model, the Terrestrial Ecosystem Model (TEM). The adjoint model of TEM was then used to: (1) conduct sensitivity studies of net ecosystem production (NEP) for three terrestrial ecosystems: grassland, deciduous broadleaf forest and evergreen needle‐leaf forest; (2) rank the importance of parameters in controlling NEP; (3) optimize the model parameters by assimilating eddy flux data of NEP; and (4) evaluate parameterization by extrapolating optimal parameters to other sites that have the same plant functional type as the calibration sites. We found that: (1) the maximum rate of photosynthesis ( C MAX ) was the most important parameter in determining NEP, while the importance of the remaining parameters varied depending on plant functional type, suggesting that the same ecosystem process has different degrees of importance in modeling carbon fluxes; (2) the sensitivity of NEP to C MAX had a significant seasonal variability and the control of C MAX on NEP was much larger in growing season (defined as from April to October) than that in nongrowing season (defined as from December to March); and (3) after parameterization, TEM could reasonably reproduce carbon fluxes observed at eddy flux tower sites. This study provided an effective model‐data fusion framework of TEM, which could improve the future quantification of terrestrial ecosystem carbon fluxes at both site and regional levels.

Zhu, Qing↗

Calibrating transition-metal energy levels and oxygen bands in first-principles calculations: Accurate prediction of redox potentials and charge transfer in lithium transition-metal oxides

Transition-metal (TM) oxides play an increasingly important role in technology today, including applications such as catalysis, solar energy harvesting, and energy storage. In many of these applications, the details of their electronic structure near the Fermi level are critically important for their properties. We propose a first-principles–based computational methodology for the accurate prediction of oxygen charge transfer in TM oxides and lithium TM (Li-TM) oxides. To obtain accurate electronic structures, the Heyd-Scuseria-Ernzerhof (HSE06) hybrid functional is adopted, and the amount of exact Hartree-Fock exchange (mixing parameter) is adjusted to reproduce reference band gaps. We show that the HSE06 functional with optimal mixing parameter yields not only improved electronic densities of states, but also better energetics (Li-intercalation voltages) for LiCoO 2 and LiNiO 2 as compared to the generalized gradient approximation (GGA), Hubbard U corrected GGA (GGA + U), and standard HSE06. We find that the optimal mixing parameters for TM oxides are system specific and correlate with the covalency (ionicity) of the TM species. The strong covalent (ionic) nature of TM-O bonding leads to lower (higher) optimal mixing parameters. We find that optimized HSE06 functionals predict stronger hybridization of the Co 3d and O 2p orbitals as compared to GGA, resulting in a greater contribution from oxygen states to charge compensation upon delithiation in LiCoO 2 . We also find that the band gaps of Li-TM oxides increase linearly with the mixing parameter, enabling the straightforward determination of optimal mixing parameters based on GGA (α = 0.0) and HSE06 (α = 0.25) calculations. Our results also show that G 0 W 0 @ GGA + U band gaps of TM oxides ( M O , M = Mn , Co , Ni ) and LiCoO 2 agree well with experimental references, suggesting that G 0 W 0 calculations can be used as a reference for the calibration of the mixing parameter in cases when no experimental band gap has been reported.

36 MATERIALS SCIENCE↗

Extreme Fast Charging Lithium-Ion Batteries (Final Technical Report)

The objective of this research project is to develop, design, fabricate, and demonstrate lithium ion battery cells that optimize energy density, reduce cost, and demonstrate eXtreme Fast Charging (XFC) capabilities. The XFC capability of the cell will be determined by the final specific energy of the cell after completing 500 6C charge /1C discharge cycles. Over the first 18 months of the project, over 800 cells were produced in groups of 20 cells to determine the optimum configuration of following parameters to optimized XFC performance: (1) Graphite anode material optimization (2) Electrolyte and additive optimization (3) Electrode and cell design optimization. In the final 6 months of the project, over 200 optimized cells were produced that featured optimized parameters from each of the independent studies. The final optimized cells exhibited a final specific energy of 150 Wh/kg, meeting the DOE project goal, but failing to meet the initial specific energy requirement of 180 Wh/kg.

25 ENERGY STORAGE↗

Quantifying the Impact of Vertical Resolution on the Representation of Marine Boundary Layer Physics for Global-Scale Models

Abstract While GCM horizontal resolution has received the majority of scale improvements in recent years, ample evidence suggests that a model’s vertical resolution exerts a strong control on its ability to accurately simulate the physics of the marine boundary layer. Here we show that, regardless of parameter tuning, the ability of a single-column model (SCM) to simulate the subtropical marine boundary layer improves when its vertical resolution is improved. We introduce a novel objective tuning technique to optimize the parameters of an SCM against profiles of temperature and moisture and their turbulent fluxes, horizontal winds, cloud water, and rainwater from large-eddy simulations (LES). We use this method to identify optimal parameters for simulating marine stratocumulus and shallow cumulus. The novel tuning method utilizes an objective performance metric that accounts for the uncertainty in the LES output, including the covariability between model variables. Optimization is performed independently for different vertical grid spacings and value of time step, ranging from coarse scales often used in current global models (120 m, 180 s) to fine scales often used in parameterization development and large-eddy simulations (10 m, 15 s). Uncertainty-weighted disagreement between the SCM and LES decreases by a factor of ∼5 when vertical grid spacing is improved from 120 to 10 m, with time step reductions being of secondary importance. Model performance is shown to converge at a vertical grid spacing of 20 m, with further refinements to 10 m leading to little further improvement. Significance Statement In successive generations of computer models that simulate Earth’s atmosphere, improvements have been mainly accomplished by reducing the horizontal sizes of discretized grid boxes, while the vertical grid spacing has seen comparatively lesser refinements. Here we advocate for additional attention to be paid to the number of vertical layers in these models, especially in the model layers closest to Earth’s surface where climatologically important marine stratocumulus and shallow cumulus clouds reside. Our experiments show that the ability of a one-dimensional model to represent physical processes important to these clouds is strongly dependent on the model’s vertical grid spacing.

Meteorology & Atmospheric Sciences↗

Task-based detectability in CT image reconstruction by filtered backprojection and penalized likelihood estimation

Purpose: Nonstationarity is an important aspect of imaging performance in CT and cone-beam CT (CBCT), especially for systems employing iterative reconstruction. This work presents a theoretical framework for both filtered-backprojection (FBP) and penalized-likelihood (PL) reconstruction that includes explicit descriptions of nonstationary noise, spatial resolution, and task-based detectability index. Potential utility of the model was demonstrated in the optimal selection of regularization parameters in PL reconstruction. Methods: Analytical models for local modulation transfer function (MTF) and noise-power spectrum (NPS) were investigated for both FBP and PL reconstruction, including explicit dependence on the object and spatial location. For FBP, a cascaded systems analysis framework was adapted to account for nonstationarity by separately calculating fluence and system gains for each ray passing through any given voxel. For PL, the point-spread function and covariance were derived using the implicit function theorem and first-order Taylor expansion according toFessler [“Mean and variance of implicitly defined biased estimators (such as penalized maximum likelihood): Applications to tomography,” IEEE Trans. Image Process. 5(3), 493–506 (1996)]. Detectability index was calculated for a variety of simple tasks. The model for PL was used in selecting the regularization strength parameter to optimize task-based performance, with both a constant and a spatially varying regularization map. Results: Theoretical models of FBP and PL were validated in 2D simulated fan-beam data and found to yield accurate predictions of local MTF and NPS as a function of the object and the spatial location. The NPS for both FBP and PL exhibit similar anisotropic nature depending on the pathlength (and therefore, the object and spatial location within the object) traversed by each ray, with the PL NPS experiencing greater smoothing along directions with higher noise. The MTF of FBP is isotropic and independent of location to a first order approximation, whereas the MTF of PL is anisotropic in a manner complementary to the NPS. Task-based detectability demonstrates dependence on the task, object, spatial location, and smoothing parameters. A spatially varying regularization “map” designed from locally optimal regularization can improve overall detectability beyond that achievable with the commonly used constant regularization parameter. Conclusions: Analytical models for task-based FBP and PL reconstruction are predictive of nonstationary noise and resolution characteristics, providing a valuable framework for understanding and optimizing system performance in CT and CBCT.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Optimal filtration of the atmospheric parameters profiles

The idea of optimal Marcovian filtration of fluctuating profiles from lidar signals is developed but as applied to a double-frequency sounding which allows the use of large cross sections of elastic scattering and correct separation of the contributions due to aerosol and Rayleigh scatterings from the total lidar return. The filtration efficiency is shown under different conditions of sounding using a computer model. The accuracy of restituted profiles (temperature, pressure, density) is determined by the elements of a posteriori matrix K. The results obtained allow the determination of the lidar power required for providing the necessary accuracy of restitution of the atmospheric parameter profiles at chosen wavelengths of sounding in the ultraviolet and visible range.

Zuev, V. E.↗

Basal glycogenolysis in mouse skeletal muscle: in vitro model predicts in vivo fluxes

A previously published mammalian kinetic model of skeletal muscle glycogenolysis, consisting of literature in vitro parameters, was modified by substituting mouse specific Vmax values. The model demonstrates that glycogen breakdown to lactate is under ATPase control. Our criteria to test whether in vitro parameters could reproduce in vivo dynamics was the ability of the model to fit phosphocreatine (PCr) and inorganic phosphate (Pi) dynamic NMR data from ischemic basal mouse hindlimbs and predict biochemically-assayed lactate concentrations. Fitting was accomplished by optimizing four parameters--the ATPase rate coefficient, fraction of activated glycogen phosphorylase, and the equilibrium constants of creatine kinase and adenylate kinase (due to the absence of pH in the model). The optimized parameter values were physiologically reasonable, the resultant model fit the [PCr] and [Pi] timecourses well, and the model predicted the final measured lactate concentration. This result demonstrates that additional features of in vivo enzyme binding are not necessary for quantitative description of glycogenolytic dynamics.

Non-NASA Center↗

Energetic protons from an ultraintense laser interacting with a symmetric parabolic concave target

A scheme of a symmetric parabolic concave target irradiated by an ultraintense laser for efficient proton acceleration is proposed and involved problem is studied by using two-dimensional particle-in-cell (PIC) simulations. Results indicate that on one hand, the laser field is focused by the front parabolic concave surface of target and, on the other hand, more energetic hot electrons will traverse to the rear surface of target due to concave shape. The space-charge-separation field, induced by those hot electrons escaping form parabolic concave rear surface of target, can accelerate protons to relatively high energy with narrow energy spread. The dependence of the efficiency of proton acceleration on the target parameters is examined, and the optimal target parameters are obtained. Particle-in-cell simulations show that the proton peak energy and energy spread are greatly enhanced when the target parameters are chosen optimal, for example, a proton bunch with the maximum energy {approx}27.5 MeV and energy spread {approx}7% can be generated. Some implications of our results to experiments and comparisons with the other works are also discussed briefly.

43 PARTICLE ACCELERATORS↗

System and method for reasoning about the optimality of a configuration parameter of a distributed system

Embodiments provide a system and method for reasoning about the optimality of a configuration parameter of a distributed system. During operation, the system obtains a multi-layer graph for a system with a plurality of components, wherein the multi-layer graph comprises a configuration subgraph, a vulnerability subgraph, and a dependency subgraph. The system determines, based on the multi-layer graph, constraint relationships associated with configuration parameters for the components, wherein the constraint relationships include security constraints and functionality constraints. The system computes an unsatisfiable core which comprises a set of mutually incompatible constraints. The system resolves, based on a strategy and over multiple iterations, the unsatisfiable core by analyzing one pair of mutually incompatible constraints per a respective iteration, to obtain a new unsatisfiable core which comprises a smaller number of mutually incompatible constraints than the computed unsatisfiable core or a previously computed unsatisfiable core from a most recent iteration.

Soroush, Hamed↗