Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

An Improved Cryosat-2 Sea Ice Freeboard Retrieval Algorithm Through the Use of Waveform Fitting

We develop an empirical model capable of simulating the mean echo power cross product of CryoSat-2 SAR and SAR In mode waveforms over sea ice covered regions. The model simulations are used to show the importance of variations in the radar backscatter coefficient with incidence angle and surface roughness for the retrieval of surfaceelevation of both sea ice floes and leads. The numerical model is used to fit CryoSat-2 waveforms to enable retrieval of surface elevation through the use of look-up tables and a bounded trust region Newton least squares fitting approach. The use of a model to fit returns from sea ice regions offers advantages over currently used threshold retrackingmethods which are here shown to be sensitive to the combined effect of bandwidth limited range resolution and surface roughness variations. Laxon et al. (2013) have compared ice thickness results from CryoSat-2 and IceBridge, and found good agreement, however consistent assumptions about the snow depth and density of sea ice werenot used in the comparisons. To address this issue, we directly compare ice freeboard and thickness retrievals from the waveform fitting and threshold tracker methods of CryoSat-2 to Operation IceBridge data using a consistent set of parameterizations. For three IceBridge campaign periods from March 20112013, mean differences (CryoSat-2 IceBridge) of 0.144m and 1.351m are respectively found between the freeboard and thickness retrievals using a 50 sea ice floe threshold retracker, while mean differences of 0.019m and 0.182m are found when using the waveform fitting method. This suggests the waveform fitting technique is capable of better reconciling the seaice thickness data record from laser and radar altimetry data sets through the usage of consistent physical assumptions.

CryoSat-2↗

Improving indirect-drive ablator performance through pulse shaping and material selection in double shell implosions

The double shell path to inertially confined volumetric thermonuclear burn relies on efficient kinetic energy transfer from an outer ablator shell to an inner shell containing DT fuel at implosion velocities near 250 km/s. In order to experimentally realize adequate compression, target imperfections and assembly features must be tightly controlled. Pulse shape and ablator material are critical design choices that impact all aspects of the implosion. In this article, we evaluate three designs: an Al ablator with single-shock radiation drive, a CH ablator with single-shock drive, and a CH ablator with reduced-adiabat 2-shock drive. All designs use the same W inner (pusher) shell overcoated with a glow discharge polymer tamper and filled with liquid-density DT. One-dimensional HYDRA simulations revealed that the plastic ablator design required the use of the 2-shock drive to match the performance of the Al design. Two-dimensional simulations resolving broadband surface roughness up to modes of several hundred placed only on the ablator showed plastic to greatly outperform Al. The plastic ablator designs did exhibit higher levels of inner shell instability growth when surface roughness was only placed at the pusher/tamper interface, which was mitigated with higher foam cushion densities. A unique and additional benefit of a plastic ablator is also discussed, where heating of the ablator by Au M-band radiation is predicted to rapidly expand the hemi-shell surfaces, closing the equatorial joint gap ahead of the first shock. Taken together, the properties of the plastic ablator for indirect-drive double shell implosions appear promising in removing several long-standing fabrication challenges.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Accurate potential drop sheet resistance measurements of laser-doped areas in semiconductors

It is investigated how potential drop sheet resistance measurements of areas formed by laser-assisted doping in crystalline Si wafers are affected by typically occurring experimental factors like sample size, inhomogeneities, surface roughness, or coatings. Measurements are obtained with a collinear four point probe setup and a modified transfer length measurement setup to measure sheet resistances of laser-doped lines. Inhomogeneities in doping depth are observed from scanning electron microscope images and electron beam induced current measurements. It is observed that influences from sample size, inhomogeneities, surface roughness, and coatings can be neglected if certain preconditions are met. Guidelines are given on how to obtain accurate potential drop sheet resistance measurements on laser-doped regions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Enhanced electron transport in dye-sensitized solar cells using short ZnO nanotips on a rough metal anode.

Many efforts have been directed toward the enhancement of electron transport in dye-sensitized solar cells (DSSC) using one-dimensional nanoarchitectured semiconductors. However, the improvement resulting from these ordered 1-D nanostructured electrodes is often offset or diminished by the deterioration in other device parameters intrinsically associated with the use of these 1-D nanostructures, such as the two-sided effect of the length of the nanowires impacting the series resistance and roughness factor. In this work, we mitigate this problem by allocating part of the roughness factor to the collecting anode instead of imparting all the roughness factors onto the semiconductor layer attached to the anode. A microscopically rough Zn microtip array is used as an electron-collecting anode on which ZnO nanotips are grown to serve as the semiconductor component of the DSSC. For the same surface roughness factor, our Zn-microtip|ZnO-nanotip DSSC exhibits an enhanced fill factor compared with DSSCs that have ZnO nanowires supported by a planar anode. In addition, the open-circuit voltage of the Zn-microtip|ZnO-nanotip DSSC is also improved due to a favorable band shift at the Zn-ZnO interface, which raises the Fermi level of the semiconductor and consequently enlarges the energy gap between the quasi-Fermi level of ZnO and the redox species. With these improvements, the overall efficiency becomes 1.4% with an open-circuit voltage of 770 mV, while the surface roughness factor of ZnO is approximately 60. Electrochemical impedance spectroscopic study reveals that the electron collection time is much shorter than the electron lifetime, suggesting that fast electron collection occurs in our device due to the significantly reduced electron collection distance along the short ZnO nanotips. The overall improvement demonstrates a new approach to enhance the efficiency of dye-sensitized solar cells.

14 SOLAR ENERGY↗

Protected electrode structures and methods

An electrode structure and its method of manufacture are disclosed. The disclosed electrode structures may be manufactured by depositing a first release layer on a first carrier substrate. A first protective layer may be deposited on a surface of the first release layer and a first electroactive material layer may then be deposited on the first protective layer. The first protective layer may have a low mean peak to valley surface roughness and/or may be thin. In some embodiments, an interface between the first protective layer and the first electroactive material layer has a low mean peak to valley surface roughness.

Mikhaylik, Yuriy V.↗

Methods of forming electrode structures

An electrode structure and its method of manufacture are disclosed. The disclosed electrode structures may be manufactured by depositing a first release layer on a first carrier substrate. A first protective layer may be deposited on a surface of the first release layer and a first electroactive material layer may then be deposited on the first protective layer. Subsequently, the first carrier substrate may be delaminated from the first release layer. The first release layer may then be removed from the first protective layer by dissolution in an electrolyte. The first protective layer may have a low mean peak to valley surface roughness and/or may be thin. In some embodiments, an interface between the first protective layer and the first electroactive material layer has a low mean peak to valley surface roughness. In some embodiments, a thickness of the first protective layer is greater than a mean peak to valley roughness of the first release layer. In some embodiments, an adhesive strength between the first release layer and the first protective layer is greater than an adhesive strength between the first release layer and the first carrier substrate.

Mikhaylik, Yuriy V.↗

Radar-anomalous, high-altitude features on Venus

Over nearly all of the surface of Venus the reflectivity and emissivity at centimeter wavelengths are about 0.15 and 0.85 respectively. These values are consistent with moderately dense soils and rock populations, but the mean reflectivity is about a factor of 2 greater than that for the Moon and other terrestrial planets. Pettingill and Ford, using Pioneer Venus reflectivities and emissivities, found a number of anomalous features on Venus that showed much higher reflectivities and much lower emissivities with both values approaching 0.5. These include Maxwell Montes, a number of high regions in Aphrodite Terra and Beta Regio, and several isolated mountain peaks. Most of the features are at altitudes above the mean radius by 2 to 3 km or more. However, such features have been found in the Magellan data at low altitudes and the anomalies do not exist on all high structures, Maat Mons being the most outstanding example. A number of papers have been written that attempt to explain the phenomena in terms of the geochemistry balance of weathering effects on likely surface minerals. The geochemists have shown that the fundamentally basaltic surface would be stable at the temperatures and pressures of the mean radius in the form of magnetite, but would evolve to pyrite and/or pyrrhotite in the presence of sulfur-bearing compounds such as SO2. Pyrite will be stable at altitudes above 4 or 5 km on Venus. Although the geochemical arguments are rather compelling, it is vitally important to rationally look at other explanations for radar and radio emission measurements such as that presented by Tryka and Muhleman. The radar reflectivity values are retrieved from the raw Magellan backscatter measurements by fitting the Hagfors' radar scattering model in which a surface roughness parameters and a normal incidence electrical reflectivity are estimated. The assumptions of the theory behind the model must be considered carefully before the results can be believed. These include that the surface roughness exists only at horizontal scales large compared to the wavelength, the vertical deviations are gaussianly distributed, there is no shadowing, and that the reflection occurs at the interface of two homogeneous dielectric half-spaces. Probably all these conditions are violated at the anomalous features under discussion. The most important of these is the homogeneity of the near surface of Venus, particularly in highlands. Under the assumptions of the theory, all of the radio energy is reflected by the impedance jump at the very boundary. However, in heterogeneous soil some fraction of the illuminating energy is propagated into the soil and then scattered back out by impedance discontinuities such as rock, voids, and cracks. In light soils, the latter effect can overwhelm the scattering effects of the true surface and greatly enhance the backscatter power, suggesting a much higher value of an effective dielectric constant that would be estimated from Hagfors' model.

Muhleman, Duane O.↗

Studying femtosecond-laser hyperdoping by controlling surface morphology

We study the fundamental properties of femtosecond-laser (fs-laser) hyperdoping by developing techniques to control the surface morphology following laser irradiation. By decoupling the formation of surface roughness from the doping process, we study the structural and electronic properties of fs-laser doped silicon. These experiments are a necessary step toward developing predictive models of the doping process. We use a single fs-laser pulse to dope silicon with sulfur, enabling quantitative secondary ion mass spectrometry, transmission electron microscopy, and Hall effect measurements. These measurements indicate that at laser fluences at or above 4 kJ m{sup -2}, a single laser pulse yields a sulfur dose >(3 {+-} 1) x 10{sup 13} cm{sup -2} and results in a 45-nm thick amorphous surface layer. Based on these results, we demonstrate a method for hyperdoping large areas of silicon without producing the surface roughness.

36 MATERIALS SCIENCE↗

Effects of enviromentally imposed roughness on airfoil performance

The experimental evidence for the effects of rain, insects, and ice on airfoil performance are examined. The extent to which the available information can be incorporated in a calculation method in terms of change of shape and surface roughness is discussed. The methods described are based on the interactive boundary layer procedure of Cebeci or on the thin layer Navier Stokes procedure developed at NASA. Cases presented show that extensive flow separation occurs on the rough surfaces.

Cebeci, Tuncer↗

Effects of environmentally imposed roughness on airfoil performance

The experimental evidence for the effects of rain, insects, and ice on airfoil performance are examined. The extent to which the available information can be incorporated in a calculation method in terms of change of shape and surface roughness is discussed. The methods described are based on the interactive boundary procedure of Cebeci or on the thin layer Navier Stokes procedure developed at NASA. Cases presented show that extensive flow separation occurs on the rough surfaces.

Cebeci, Tuncer↗

Carbon-Nanotube-Carpet Heat-Transfer Pads

Microscopic thermal-contact pads that include carpet-like arrays of carbon nanotubes have been invented for dissipating heat generated in integrated circuits and similarly sized single electronic components. The need for these or other innovative thermal-contact pads arises because the requisite high thermal conductances cannot be realized by scaling conventional macroscopic thermal-contact pads down to microscopic sizes. Overcoming limitations of conventional thermal-contact materials and components, the carbon-nanotube thermal-contact pads offer the high thermal conductivities needed to accommodate the high local thermal power densities of modern electronic circuits, without need for large clamping pressures, extreme smoothness of surfaces in contact, or gap-filling materials (e.g., thermally conductive greases) to ensure adequate thermal contact. Moreover, unlike some conventional thermal-contact components, these pads are reusable. The figure depicts a typical pad according to the invention, in contact with a rough surface on an electronic component that is to be cooled. Through reversible bending and buckling of carbon nanotubes at asperities on the rough surface, the pad yields sufficiently, under relatively low contact pressure, that thermal contact is distributed to many locations on the surface to be cooled, including valleys where contact would not ordinarily occur in conventional clamping of rigid surfaces. Hence, the effective thermal-contact area is greater than that achievable through scaling down of a macroscopic thermal-contact pad. The extremely high longitudinal thermal conductivities of the carbon nanotubes are utilized to conduct heat away from potential hot spots on the surface to be cooled. The fibers protrude from a layer of a filler material (Cu, Ag, Au, or metal-particle- filled gels), which provides both mechanical support to maintain the carbon nanotubes in alignment and thermal conductivity to enhance the diffusion of concentrated heat from the nanotubes into the larger adjacent volume of a heat sink. The array of carbon nanotubes, the filler material, and the heat sink are parts of a unitary composite structure that is fabricated as follows: 1. Using techniques that have been reported previously, the array of substantially perpendicularly oriented carbon nanotubes is grown on a metal, silicon, or other suitable thermally conductive substrate that is intended to become the heat sink. 2. By means of chemical vapor deposition, physical vapor deposition, plasma deposition, ion sputtering, electrochemical deposition, or casting from a liquid phase, some or all of the interstitial volume between carbon nanotubes is filled with the aforementioned layer of mechanically supporting, thermally conductive material. 3. To cause the carbon nanotubes to protrude the desired length from the filler material, an outer layer of filler is removed by mechanical polishing, chemical mechanical polishing, wet chemical etching, electrochemical etching, or dry plasma etching.

Li, Jun↗

Modeling the non-grey-body thermal emission from the full moon

The present series of thermophysical computer models for solid-surfaced planetary bodies whose surface roughness is modeled as paraboloidal craters of specified depth/diameter ratio attempts to characterize the nongrey-body brightness temperature spectra of the moon and of the Galilean satellites. This modeling, in which nondiffuse radiation properties and surface roughness are included for rigorous analysis of scattered and reemitted radiation within a crater, explains to first order the behavior of both limb-scans and disk-integrated IR brightness temperature spectra for the full moon. Only negative surface relief can explain lunar thermal emissions' deviation from smooth Lambert-surface expectations.

Vogler, Karl J.↗

A Generalized Wall Function

The asymptotic solutions, described by Tennekes and Lumley (1972), for surface flows in a channel, pipe or boundary layer at large Reynolds numbers are revisited. These solutions can be extended to more complex flows such as the flows with various pressure gradients, zero wall stress and rough surfaces, etc. In computational fluid dynamics (CFD), these solutions can be used as the boundary conditions to bridge the near-wall region of turbulent flows so that there is no need to have the fine grids near the wall unless the near-wall flow structures are required to resolve. These solutions are referred to as the wall functions. Furthermore, a generalized and unified law of the wall which is valid for whole surface layer (including viscous sublayer, buffer layer and inertial sublayer) is analytically constructed. The generalized law of the wall shows that the effect of both adverse and favorable pressure gradients on the surface flow is very significant. Such as unified wall function will be useful not only in deriving analytic expressions for surface flow properties but also bringing a great convenience for CFD methods to place accurate boundary conditions at any location away from the wall. The extended wall functions introduced in this paper can be used for complex flows with acceleration, deceleration, separation, recirculation and rough surfaces.

Shih, Tsan-Hsing↗

In situ non-destructive measurement of biofilm thickness and topology in an interferometric optical microscope

Biofilms are ubiquitous and deleteriously impact a wide range of industrial processes, medical and dental health issues, and environmental problems such as transport of invasive species and the fuel efficiency of ocean going vessels. Biofilms are difficult to characterize when fully hydrated, especially in a non-destructive manner, because of their soft structure and water-like bulk properties. Herein we describe a non-destructive high resolution method of measuring and monitoring the thickness and topology of live biofilms of using white light interferometric optical microscopy. Using this technique, surface morphology, surface roughness, and biofilm thickness can be measured non-destructively and with high resolution as a function of time without disruption of the biofilm activity and processes. The thickness and surface topology of a P. putida biofilm were monitored growing from initial colonization to a mature biofilm. Typical bacterial growth curves were observed. Increase in surface roughness was a leading indicator of biofilm growth.

biofilm↗

Methods for improving the damage performance of fused silica polished by magnetorheological finishing

The laser-induced damage threshold of fused-silica samples processed via magnetorheological finishing is investigated for polishing compounds depending on the type of abrasive material and the post-polishing surface roughness. The effectiveness of laser conditioning is examined using a ramped pre-exposure with the same 351-nm, 3-ns Gaussian pulses. Lastly, we examine chemical etching of the surface and correlate the resulting damage threshold to the etching protocol. A combination of etching and laser conditioning is found to improve the damage threshold by a factor of ~3, while maintaining <1-nm surface roughness.

36 MATERIALS SCIENCE↗

A boundary-layer analysis of atmospheric motion over a semi-elliptical surface obstruction

Flow over surface obstructions can produce adverse flying conditions for helicopters, V/STOL vehicles, etc. The disturbed boundary-layer concept is applied in approximating the localized flow field induced around a surface obstruction (modeled by a two-dimensional cylinder with elliptical cross section) by an impinging wind. The analysis concludes that: (1) localized wind-speed maxima occur at the top of a surface obstruction, which are expected in physically real flows; (2) increased elliptical aspect ratio decreases with speed within the boundary layer at the top of the ellipse; (3) increased surface roughness decreases velocity in the boundary layer; (4) Reynolds number has a negligible effect on the overall flow for the Re range considered; (5) decreased elliptical aspect ratio and increased surface roughness cause larger separation regions.

Frost, W.↗

A lag model for turbulent boundary layers developing over rough bleed surfaces

Boundary layer mass removal (bleed) through spanwise bands of holes on a surface is used to prevent or control separation and to stabilize the normal shock in supersonic inlets. The addition of a transport equation lag relationship for eddy viscosity to the rough wall algebraic turbulence model of Cebeci and Chang was found to improve agreement between predicted and measured mean velocity distributions downstream of a bleed band. The model was demonstrated for a range of bleed configurations, bleed rates, and local free stream Mach numbers. In addition, the model was applied to the boundary layer development over acoustic lining materials for the inlets and nozzles of commercial aircraft. The model was found to yield accurate results for integral boundary layer properties unless there was a strong adverse pressure gradient.

Lee, J.↗

Effect of Out-Gassing on the Onset of Hypersonic Boundary Layer Transition

Prediction and control of the onset of transition and the associated variation in aerothermodynamic parameters in high-speed flows is key to optimize the performance and design of Thermal Protection Systems (TPS) of next-generation aerospace vehicles [1]. Boundary Layer Transition (BLT) characteristics can influence the surface heating budget determining the TPS thickness and consequently its weight penalty. Ablative heatshields are designed to alleviate the high heat flux at the surface through pyrolysis of their polymeric matrix and subsequent fiber ablation [2]. Pyrolysis leads to out-gassing and non-uniform ablation lead to surface roughness, both of which are known to influence the transition process. An ablator impacts BLT through three main routes: gas injecting into the boundary layer from the wall, changing the surface heat transfer due to wall-flow chemical reactions, and modifying surface roughness [3]. In preparation to Mars 2020 mission post-flight analysis, the predictive transition capability has been initiated toward hard-coupling porous material response analysis and aerothermal environment calculation.

Karimi, Mona↗