Search NASA⌕ Search

SEARCH · Search NASA

Results for “solidification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Computational Investigation of Melt Pool Process Dynamics and Pore Formation in Laser Powder Bed Fusion

In the laser powder bed fusion additive manufacturing process, the presence of porosity may result in cracks and significantly affects the part performance. A comprehensive understanding of the melt pool process dynamics and porosity evolution can help to improve build quality. In this study, a novel multi-physics computational fluid dynamics (CFD) model has been applied to investigate the fluid dynamics in melt pools and resultant pore defects. To accurately capture the melting and solidification process, major process physics, such as the surface tension, evaporation as well as laser multi-reflection, have been considered in the model. A discrete element method is utilized to model the generation of powder spreading upon build plate by additional numerical simulations. Multiple single track experiments have been performed to obtain the melt pool shape and cross-sectional dimension information. The predicted melt pool dimensions were found to have a reasonable agreement with experimental measurements, e.g., the errors are in the range of 1.3 to 10.6% for melt pool width, while they are between 1.4 and 15.9% for melt depth. Pores are captured by both CFD simulation and x-ray computed tomography measurement for the case with a laser power of 350 W and laser speed of 100 mm/s. The formation of keyholes maybe related to the melt pool front wall angle, and it is found that the front wall angle increases with the increase in laser line energy density. In addition, a larger laser power or smaller scanning speed can help to generate keyhole-induced pores; they also contribute to produce larger sized pores.

36 MATERIALS SCIENCE↗

Long-Term Creep Behavior of a CoCrFeNi Medium-Entropy Alloy

We report that current research shows that high-entropy alloys (HEAs) can offer superior oxidation resistance compared to more traditional austenitic stainless steels with equivalent tensile mechanical performance. While many reports have been published on creep of CoCrFeNiMn, few focus on the CoCrFeNi family of low to medium entropy alloys. In this manuscript, uniaxial tensile creep test results for more than 46,000 accumulated hours are presented on the equiatomic CoCrFeNi alloy. The alloy was manufactured at NETL using a vacuum induction melt solidification approach with a computationally designed homogenization cycle. After completing the homogenization cycle, the ingot was first hot forged and then hot rolled into 10 mm thick plate, a product form that is relevant to many industries. Creep tests were performed in the temperature range of 600-650 °C using applied stresses from 120 to 189 MPa. This study builds upon previous results on the CoCrFeNiMn family of high-entropy alloys and offers a modicum of clarification about performance compared to small button melts by using ASTM standard test procedures and mechanical test specimens. The apparent creep activation energy and creep stress exponent were similar to those for CoCrFe medium-entropy and CoCrFeNiMn high-entropy alloys. The post-test creep microstructure showed some Cr segregation, which has also been noted for other CoCrFe alloys. The CoCrFeNi alloy also presents a double minimum or two minimum creep rate phenomena.

36 MATERIALS SCIENCE↗

Design, Processing, and Properties of WTaCrV-Hf Multi-principal Element Alloys

Refractory multi-principal element alloys are candidates for high-temperature structural components due, in part, to their high strength and high melting points. Single-phase materials are initially preferred for isotropic material properties as a function of time and temperature in service conditions. This work outlines a computational rank-ordering and experimental validation methodology for single-phase body-centered-cubic phase stability in WTaCrV-Hf alloys using order–disorder transition temperature. Eight compositions were fabricated by arc-melting and heat-treated at 1400 °C for 24 hrs. X-ray diffraction, energy-dispersive x-ray spectroscopy, and Vickers hardness testing showed alloys with order–disorder transition temperatures below 600 °C formed a single-phase body-centered-cubic structure during solidification and remained single-phase after heat-treatment. The sample possessing the lowest order–disorder transition temperature exhibited slip traces suggestive of room-temperature plastic deformation under Vickers indentation, with both heat-treated single-phase samples exhibiting hardnesses over 800 HV with little cracking compared to tungsten. These results establish order–disorder transition temperature as a viable predictive parameter for multi-principal element alloy phase stability. The methodology outlined in this work provides a framework for future design, fabrication, and characterization of high-temperature structural multi-principal element alloys.

CALPHAD↗

The Ce-Fe-Ti System: Phase Equilibria in the Fe-rich Corner at 1000 °C

The rare earth–iron–transition metal systems are of increasing interest in the search for novel permanent magnet phases. This work reports on the solidification behavior, phase equilibria and stability range of solid phases in the ternary Ce-Fe-Ti system, focusing on the iron-rich region (> 65 at.% Fe) of the isothermal section at 1000 °C. Further, two ternary phases Ce 1.03 Fe 12-x Ti x (x = 0.87–1.02) with ThMn 12 structure type and Ce 3.06 Fe 27.6 Ti 1.4 with Nd 3 Fe 29 structure type were observed. Magnetic measurements of Ce 1.03 Fe 12-x Ti x and Ce 3.06 Fe 27.6 Ti 1.4 revealed ferromagnetic ordering with Curie temperatures of 550 K and 327 K, respectively.

36 MATERIALS SCIENCE↗

Characterization of an aluminum alloy hemispherical shell fabricated via direct metal laser melting

The ability of additive manufacturing to directly fabricate complex shapes provides characterization challenges for part qualification. The orientation of the microstructures produced by these processes will change relative to the surface normal of a complex part. In this work, the microscopy and x-ray tomography of an AlSi10Mg alloy hemispherical shell fabricated using powder bed metal additive manufacturing are used to illustrate some of these challenges. The shell was manufactured using an EOS M280 system in combination with EOS-specified powder and process parameters. The layer-by-layer process of building the shell with the powder bed additive manufacturing approach results in a position-dependent microstructure that continuously changes its orientation relative to the shell surface normal. X-ray tomography was utilized to examine the position-dependent size and distribution of porosity and surface roughness in the 98.6% dense part. Optical and electron microscopy were used to identify global and local position-dependent structures, grain morphologies, chemistry, and precipitate sizes and distributions. The rapid solidification processes within the fusion zone (FZ) after the laser transit results in a small dendrite size. Cell spacings taken from the structure in the middle of the FZ were used with published relationships to estimate a cooling rate of ~9 × 10 5 K/s. Uniformly-distributed, nanoscale Si precipitates were found within the primary α-Al grains. A thin, distinct boundary layer containing larger α-Al grains and extended regions of the nanocrystalline divorced eutectic material surrounds the FZ. Moreover, subtle differences in the composition between the latter layer and the interior of the FZ were noted with scanning transmission electron microscopy (STEM) spectral imaging.

36 MATERIALS SCIENCE↗

Interface-Driven Phenomena in Solids: Thermodynamics, Kinetics and Chemistry

The study of materials interfaces dates back over a century. In solid systems and from an engineering perspective, free surfaces and internal (grain and/or phase) boundaries influence a wide range of properties, such as thermal, electrical and optical transport, and mechanical ones. The properties and the role of interfaces has been discussed extensively in various reviews such as by Sutton and Balluffi. As the characteristic feature size of a materials system (i.e., grain size) is decreased to the nanometer scale, interface-driven physics is expected to dominate due to the increased density of such planar defects. Moreover, interfacial attributes, thermodynamics, and mobility play a key role in phase transformations, such as solidification dynamics and structural transitions in solids, and in homogenization and microstructural evolution processes, such as grain growth, coarsening, and recrystallization. In summary, the set of articles published in this special topic titled: “Interface-Driven Phenomena in Solids: Thermodynamics, Kinetics and Chemistry” covers topics related to microstructure evolution, segregation/adsorption phenomena and interface interactions with other materials defects.

36 MATERIALS SCIENCE↗

Advances and Achievements in In Situ Analysis of Corrosion and Structure–Property Relationship in Mg Alloys

Every year, TMS Magnesium Committee carefully selects a special topic in magnesium (Mg) related research and development not only having the hottest subject from both academic and industrial perspectives but also demonstrating major achievements within this subject. Following last year’s topic on Mg microallying [1], this year’s focus is on in-situ methods and associated techniques in their broad definition spanning from laboratory- to large- scale facilities to process monitoring. The applications of in-situ techniques have a wide spectrum from the analysis of melts and liquid-solid transitions to solid-state phenomena during thermo-mechanical processing and heat treatments to surface interactions with various environments. Therefore, such works are of significant interest to scientists working in the area of Mg alloy development as well as to a much broader audience from both academia and industry. This interest is primarily caused by challenges in the analysis of structure-property relationship in Mg alloys, and even cursory glance of literature reveals sharp increase of publications relevant to this topic recently. For instance, very high reactivity of Mg as well as its well-known propensity to substantially alter structure upon unloading in mechanical testing makes it difficult to understand and thus to simulate correlation between microstructures observed in post-mortem analysis and physical processes during testing or fabrication. However, recent advances in in-situ analysis based on large-scale research facilities such as neutron scattering and synchrotron radiation sources as well as microscopy-based, acoustic emission, and other more traditional techniques allowed significant achievements. Apart from apparent development of relevant experimental techniques, a significant part of this success should also be attributed to increasing accessibility of the facilities and simplification of their use from a user perspective. The selection of articles in this special topic is quite far from comprehensive review covering all aspects of in-situ methods available for metallic materials development. However, this was not the purpose in any case. Instead, this selection is intended to present several studies on Mg alloys and Mg-based composites with the use of in-situ techniques. In addition, it overviews two techniques, ‘Acoustic Emission’ (AE) and ‘Ambient-Pressure X-ray Photoelectron Spectroscopy’ (AP-XPS), that are rather novel to the Mg community. These studies are supposed to give readers representative examples of such techniques potential and to help in navigating the spectrum of modern state-of-the-art analytical methods facilitating the development of Mg alloys. These articles are organized in the order corresponding to typical Mg alloy lifecycle from material preparation and solidification to thermo-mechanical processing and product fabrication to degradation.

36 MATERIALS SCIENCE↗

Strategy for Texture Management in Metals Additive Manufacturing

Additive manufacturing (AM) technologies have long been recognized for their ability to fabricate complex geometric components directly from models conceptualized through computers, allowing for complicated designs and assemblies to be fabricated at lower costs, with shorter time to market, and improved function. Lacking behind the design complexity aspect is the ability to fully exploit AM processes for control over texture within AM components. Currently, standard heat-fill strategies utilized in AM processes result in largely columnar grain structures. Here, we propose a point heat source fill for the electron beam melting (EBM) process through which the texture in AM materials can be controlled. Using this point heat source strategy, the ability to form either columnar or equiaxed grain structures upon solidification through changes in the process parameters associated with the point heat source fill is demonstrated for the nickel-base superalloy, Inconel 718. Mechanically, the material is demonstrated to exhibit either anisotropic properties for the columnar-grained material fabricated through using the standard raster scan of the EBM process or isotropic properties for the equiaxed material fabricated using the point heat source fill.

36 MATERIALS SCIENCE↗

Compression Molding and Novel Sintering Treatments for Alnico Type-8 Permanent Magnets in Near-Final Shape with Preferred Orientation

We present economic uncertainty in the rare earth (RE) permanent magnet marketplace, as well as in an expanding electric drive vehicle market that favors permanent magnet alternating current synchronous drive motors, motivated renewed research in RE-free permanent magnets like “alnico,” an Al-Ni-Co-Fe alloy. Thus, high-pressure, gas-atomized isotropic type-8H pre-alloyed alnico powder was compression molded with a clean burn-out binder to near-final shape and sintered to density >99% of cast alnico 8 (full density of 7.3 g/cm 3 ). To produce aligned sintered alnico magnets for improved energy product and magnetic remanence, uniaxial stress was attempted to promote controlled grain growth, avoiding directional solidification that provides alignment in alnico 9. Lastly, successful development of solid-state powder processing may enable anisotropically aligned alnico magnets with enhanced energy density to be mass-produced.

36 MATERIALS SCIENCE↗

CALPHAD Uncertainty Quantification and TDBX

CALPHAD uncertainty quantification (UQ) is the foundation of materials design with quantified confidence. We report a framework and software packages to enable CALPHAD UQ assessment and calculation using commercial CALPHAD software (Thermo-Calc). This Bayesian inference framework is coupled with a Markov chain Monte Carlo algorithm to establish uncertainty traces with a given thermodynamic database file (TDB) and corresponding experimental data points. This general framework is demonstrated with the Ni–Cr binary system. The algorithm is firstly validated on synthetic data with known ground truth. Then it is applied to real experimental data to generate posterior traces. We develop a file format named TDBX, which provides a single source of truth by combining the original TDB content and the traces for each assessed Gibbs energy parameter. CALPHAD UQ calculations are performed based on the TDBX file, from which uncertainties for phase boundaries, enthalpy curves, and solidification range are collected as examples of basic design parameters. This TDBX file with corresponding scripts are made open-source. Finally, the combination of CALPHAD UQ assessments and calculations connected by TDBX supports uncertainty-assisted modeling, enabling the integrated application of modern design with uncertainty methodologies to computational materials design.

36 MATERIALS SCIENCE↗

Pitting Corrosion in 316L Stainless Steel Fabricated by Laser Powder Bed Fusion Additive Manufacturing: A Review and Perspective

Abstract 316L stainless steel (316L SS) is a flagship material for structural applications in corrosive environments, having been extensively studied for decades for its favorable balance between mechanical and corrosion properties. More recently, 316L SS has also proven to have excellent printability when parts are produced with additive manufacturing techniques, notably laser powder bed fusion (LPBF). Because of the harsh thermo-mechanical cycles experienced during rapid solidification and cooling, LPBF processing tends to generate unique microstructures. Strong heterogeneities can be found inside grains, including trapped elements, nano-inclusions, and a high density of dislocations that form the so-called cellular structure. Interestingly, LPBF 316L SS not only exhibits better mechanical properties than its conventionally processed counterpart, but it also usually offers much higher resistance to pitting in chloride solutions. Unfortunately, the complexity of the LPBF microstructures, in addition to process-induced defects, such as porosity and surface roughness, have slowed progress toward linking specific microstructural features to corrosion susceptibility and complicated the development of calibrated simulations of pitting phenomena. The first part of this article is dedicated to an in-depth review of the microstructures found in LPBF 316L SS and their potential effects on the corrosion properties, with an emphasis on pitting resistance. The second part offers a perspective of some relevant modeling techniques available to simulate the corrosion of LPBF 316L SS, including current challenges that should be overcome.

Voisin, T. (ORCID:0000000287462659)↗

Mechanical Behavior of Additively Manufactured Molybdenum and Fabrication of Microtextured Composites

Refractory metals are a class of high-melting-temperature materials suitable for use in extreme environment applications. Interestingly, during additive manufacturing many pure refractory metals exhibit a switch from (001) to (111) build direction fiber preference with increasing surface energy density. Here we exploit this solidification physics to fabricate material with “mesoscale composite” engineered structures consisting of features with contrasting (001) and (111) build direction microtextures. Separately, elevated temperature tensile testing of EBM fabricated material with a randomized distribution of mixed (001)/(111)-fiber grains is shown to exhibit excellent properties. These results are utilized to build a crystal plasticity model for evaluating the local inelastic response of the composite mesoscale structures. Analysis of printed microstructures and microstructure-scale simulations indicate that both macro-scale and localized material behavior may be tailored. This strategy can be potentially used to synthesize materials with optimized performance for high-temperature applications.

36 MATERIALS SCIENCE↗

Laser Powder Bed Fusion of ODS 14YWT from Gas Atomization Reaction Synthesis Precursor Powders

Abstract Laser powder bed fusion (LPBF) additive manufacturing (AM) is a promising route for the fabrication of oxide dispersion strengthened (ODS) steels. In this study, 14YWT ferritic steel powders were produced by gas atomization reaction synthesis (GARS). The rapid solidification resulted in the formation of stable, Y-containing intermetallic Y 2 Fe 17 on the interior of the powder and a stable Cr-rich oxide surface. The GARS powders were consolidated with LPBF. Process parameter maps identified a stable process window resulting in a relative density of 99.8%. Transmission electron microscopy and high-energy x-ray diffraction demonstrated that during LPBF, the stable phases in the powder dissociated in the liquid melt pool and reacted to form a high density (1.7 × 10 20 /m 3 ) of homogeneously distributed Ti 2 Y 2 O 7 pyrochlore dispersoids ranging from 17 to 57 nm. The use of GARS powder bypasses the mechanical alloying step typically required to produce ODS feedstock. Preliminary mechanical tests demonstrated an ultimate tensile and yield strength of 474 MPa and 312 MPa, respectively.

36 MATERIALS SCIENCE↗

Friction Extrusion: Solid-State Metal Synthesis and Recycling in Sustainable Manufacturing

Friction extrusion (FE) is a novel solid-state process for synthesis and recycling of metals and alloys. The novelty of FE is that it utilizes the frictional heating and extensive plastic deformation intrinsic in the process to stir, mechanically alloy, consolidate, and convert powders, chips, and other recyclable feedstock metals into a usable product form of highly engineered materials. FE represents a potentially transformational sustainable manufacturing technology. Being a solid-state process, it eliminates the energy-intensive melting and solidification steps, which are necessary in the conventional metal recycle and synthesis processes. Therefore, FE is a highly energy-efficient, practically zero-emission, and economically competitive process. Here, in this work, the concept and configuration of FE are introduced, the energy-saving advantage of FE is analyzed, the feasibility of FE is demonstrated with synthesizing Al alloys, and the results of some metallographic and mechanical properties studies are presented. A prognosis of the friction extrusion technology is outlined.

36 MATERIALS SCIENCE↗

Refining Microstructures in Additively Manufactured Al/Cu Gradients Through TiB 2 Inclusions

Here, the additive manufacture of compositionally graded Al/Cu parts by laser engineered net shaping (LENS) is demonstrated. The use of a blue light build laser enabled deposition on a Cu substrate. The thermal gradient and rapid solidification inherent to selective laser melting enabled mass transport of Cu up to 4 mm from a Cu substrate through a pure Al deposition, providing a means of producing gradients with finer step sizes than the printed layer thicknesses. Divorcing gradient continuity from layer or particle size makes LENS a potentially enabling technology for the manufacture of graded density impactors for ramp compression experiments. Printing graded structures with pure Al, however, was prevented by the growth of Al 2 Cu 3 dendrites and acicular grains amid a matrix of Al 2 Cu. A combination of adding TiB 2 grain refining powder and actively varying print layer composition suppressed the dendritic growth mode and produced an equiaxed microstructure in a compositionally graded part. Material phase was characterized for crystal structure and nanoindentation hardness to enable a discussion of phase evolution in the rapidly solidifying melt pool of a LENS print.

36 MATERIALS SCIENCE↗

Suppressing Ordering in Equiatomic Fe-Co via Laser Powder Bed Fusion

Neutron and electron diffraction was employed to evaluate the effectiveness of thermal management strategies in suppressing the formation of the equilibrium-ordered B2 (CsCl) phase in equiatomic binary Fe-Co specimens fabricated by laser powder bed fusion additive manufacturing. Specimens with a tensile dogbone geometry were fabricated using various combinations of process parameters (laser power and raster speed) and thermal management strategies (no support struts, struts only in the top gauge section, and struts throughout the gauge section). Diffraction results demonstrate that the rapid solidification during PBF-L effectively minimized B2 formation, with laser power and effective scan velocity having no significant impact on the degree of ordering. Furthermore, the inclusion of support struts in the top grip region had no perceivable impact on ordering, whereas specimens with support struts in the gauge region exhibited no detectable ordering. Results are discussed in the context of thermal finite element analysis predictions.

Laser Material Processing↗

Solute Redistribution During Aging in a Laser-Based Powder Bed Fusion-Produced Fe-18Ni-9Co-5Mo-Ti Maraging Steel

Solute distribution during the laser-based powder bed fusion of metals process is highly complex because of solidification. This study builds on a previous investigation of how solute heterogeneities across different scales influence phase distribution and aging physical phenomena in a Fe-18Ni-9Co-5Mo-Ti maraging steel (Santana et al. in Addit Manuf 104494, 2024). Previous work using energy-dispersive X-ray spectroscopy revealed heterogeneous Ni and Mo enrichment at intercellular regions. Using X-ray diffraction, 8 ± 3% retained austenite was quantified in as-built samples. Additionally, electron backscatter diffraction analysis exposed the location of retained austenite along cell boundaries. In this work, scanning transmission electron microscopy results revealed the presence of non-enriched retained austenite in the as-built condition. With increased aging temperature, Ni and Mo enrichment in austenite increased, especially at the austenite/martensite boundary. Solute diffusion was simulated in DICTRA Thermo-Calc® software to assess solute redistribution between the matrix and second phases and to comprehend whether elemental diffusion processes are interconnected. Three different scenarios were considered: (1) solute diffusion in the matrix; (2) diffusion with enriched austenite in the intercellular region; (3) diffusion with non-enriched austenite in the intercellular region. Results showed that Ni partitioning controls austenite growth and that boundary regions exhibit higher element enrichment than the core.

42 ENGINEERING↗

Ability to Simulate Absorption and Melt Pool Dynamics for Laser Melting of Bare Aluminum Plate: Results and Insights from the 2022 Asynchronous AM-Bench Challenge

The 2022 Asynchronous AM-Bench challenge was designed to test the ability of simulations to accurately predict laser power absorption as well as various melt pool behaviors (width, depth, and solidification) during laser melting of solid metal during stationary and scanned laser illumination. In this challenge, participants were asked to predict a series of experimental outcomes. Experimental data were obtained from a series of experiments performed at the Advanced Photon Source at Argonne National Laboratories in 2019. These experiments combined integrating sphere radiometry with high-speed X-ray imaging, allowing for the simultaneous recording of absolute laser power absorption and two-dimensional, projected images of the melt pool. All challenge problems were based on experiments using bare aluminum solid metal. Participants were provided with pertinent experimental information like laser power, scan speed, laser spot size, and material composition. Additionally, participants were given absorptance and X-ray imaging data from stationary and scanned laser experiments on solid Ti–6Al–4V that could be used for testing their models before attempting challenge problems. In total, this challenge received 56 submissions from eight different research groups for eight individual challenge problems. The data for this challenge, and associated information, are available for download from the NIST Public Data Repository. This paper summarizes the results from the 2022 Asynchronous AM-Bench challenge as well as discusses the lessons learned to help inform future challenges.

36 MATERIALS SCIENCE↗