Search NASA⌕ Search

SEARCH · Search NASA

Results for “structural testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Direct structural parameter identification by modal test results

A direct identification procedure is proposed to obtain the mass and stiffness matrices based on the test measured eigenvalues and eigenvectors. The method is based on the theory of matrix perturbation in which the correct mass and stiffness matrices are expanded in terms of analytical values plus a modification matrix. The simplicity of the procedure enables real time operation during the structural testing.

Chen, J.-C.↗

High-R Walls for New Construction Structural Performance: Integrated Rim Header Testing

Two prominent approaches within the Building America Program to construct higher R-value walls have included use of larger dimension framing and exterior rigid foam insulation. These approaches have been met with some success; however for many production builders, where the cost of changing framing systems is expensive, the changes have been slow to be realized. In addition, recent building code changes have raised some performance issues for exterior sheathing and raised heel trusses, for example, that indicates a need for continued performance testing for wall systems. The testing methods presented in this report evaluate structural rim header designs over openings up to 6 ft wide and applicable to one- and two-story homes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Digital Image Correlation Data Processing and Analysis Techniques to Enhance Test Data Assessment and Improve Structural Simulations

The NASA Shell Buckling Knockdown Factor Project (SBKF) was established in 2007 by the NASA Engineering and Safety Center (NESC) with the primary goal to develop new analysis-based buckling design factors (a.k.a. knockdown factors) and high-fidelity buckling simulations for selected launch-vehicle-like cylindrical shell structures. A series of tests are being conducted on large-scale metallic and composite cylindrical shells in order to provide validation data for these new factors and simulations. However, the validation of these new factors and simulations is quite demanding and requires test data that is commensurate with their fidelity. Traditional instrumentation, such as linear variable displacement transducers (LVDTs) and electrical-resistance strain gages serve a critical role in providing accurate displacement and strain measurements in these tests, but only allow for data to be recorded at a select number of point locations and are not sufficient to provide all the necessary validation data. Advanced measurement technologies can be used effectively to complement traditional instrumentation and gather additional data required to validate these structural simulations. In particular, three-dimensional digital image correlation (DIC) was implemented during SBKF cylinder testing to characterize the full-field displacement and strain behavior. Commercially available VIC-3DTM software and user-written data processing scripts were used to generate valuable data and insight into the complex buckling response of the cylinders that otherwise would be impossible to gather using traditional instrumentation. In addition, the measured data from DIC was used to verify measured test data obtained from other instrumentation, enhance test and analysis correlation, and help identify the root cause of anomalous test results that may have gone unexplained if only traditional instrumentation was used. Selected test results that demonstrate the use of DIC on the SBKF cylinders are presented and a portion of the data processing methods are described.

Gardner, Nathaniel W.↗

Analysis of SNL/MSU/DOE Fatigue Database Trends for Wind Turbine Blade Materials

This report presents an analysis of trends in fatigue results from the Montana State University program on the fatigue of composite materials for wind turbine blades for the period 2005-2009. Test data can be found in the SNL/MSU/DOE Fatigue of Composite Materials Database which is updated annually. This is the fifth report in this series, which summarizes progress of the overall program since its inception in 1989. The primary thrust of this program has been research and testing of a broad range of structural laminate materials of interest to blade structures. The report is focused on current types of infused and prepreg blade materials, either processed in-house or by industry partners. Trends in static and fatigue performance are analyzed for a range of materials, geometries and loading conditions. Materials include: sixteen resins of three general types, five epoxy based paste adhesives, fifteen reinforcing fabrics including three fiber types, three prepregs, many laminate lay-ups and process variations. Significant differences in static and fatigue performance and delamination resistance are quantified for particular materials and process conditions. When blades do fail, the likely cause is fatigue in the structural detail areas or at major flaws. The program is focused strongly on these issues in addition to standard laminates. Structural detail tests allow evaluation of various blade materials options in the context of more realistic representations of blade structure than do the standard test methods. Types of structural details addressed in this report include ply drops used in thickness tapering, and adhesive joints, each tested over a range of fatigue loading conditions. Ply drop studies were in two areas: (1) a combined experimental and finite element study of basic ply drop delamination parameters for glass and carbon prepreg laminates, and (2) the development of a complex structured resin-infused coupon including ply drops, for comparison studies of various resins, fabrics and pry drop thicknesses. Adhesive joint tests using typical blade adhesives included both generic testing of materials parameters using a notched-lap-shear test geometry developed in this study, and also a series of simulated blade web joint geometries fabricated by an industry partner.

17 WIND ENERGY↗

Test Results for Autonomous Assembly of Modular Space Structures

This paper presents test results for autonomous assembly of a modular space structure. A Universal Robots UR10e manipulator with a custom end-effector, known as the Grapple Tool, was used to join TriTruss structural modules. The TriTrusses and their assembly configuration were developed for an in-space assembled telescope conceptual design. The tests presented here were performed with a 1:2.8 dimensionally scaled version of the Tri-Trusses. Robot trajectories were generated autonomously using a sample-based motion planner and an a-priori worksite model. The test results verify the assembly concept of operations as well as the software requirements for the Grapple Tool. While the Grapple Tool used in the tests was designed for the 1:2.8 scale Tri-Trusses, it has the same actuators, software, and computation architecture as the version designed for the full scale structure. The test operations consist of picking up two TriTrusses from their stowed locations and joining them to a third TriTruss mounted on a test stand and joining them to each other. This constitutes the first three modules of the in-space assembled telescope conceptual design. The paper presents the robot behavioral architecture, the generated trajectories commanded, the actual trajectories of the robot, and actuator performance of the Grapple Tool.

test↗

Test Results for Autonomous Assembly of Modular Space Structures

This paper presents test results for autonomous assembly of a modular space structure. A Universal Robots UR10e manipulator with a custom end-effector, known as the Grapple Tool, was used to join TriTruss structural modules. The TriTrusses and their assembly configuration were developed for an in-space assembled telescope conceptual design. The tests presented here were performed with a 1:2.8 dimensionally scaled version of the Tri-Trusses. Robot trajectories were generated autonomously using a sample-based motion planner and an a-priori worksite model. The test results verify the assembly concept of operations as well as the software requirements for the Grapple Tool. While the Grapple Tool used in the tests was designed for the 1:2.8 scale Tri-Trusses, it has the same actuators, software, and computation architecture as the version designed for the full scale structure. The test operations consist of picking up two TriTrusses from their stowed locations and joining them to a third TriTruss mounted on a test stand and joining them to each other. This constitutes the first three modules of the in-space assembled telescope conceptual design. The paper presents the robot behavioral architecture, the generated trajectories commanded, the actual trajectories of the robot, and actuator performance of the Grapple Tool.

test↗

High-R Walls for New Construction Structural Performance: Wind Pressure Testing

This technical report is focused primarily on laboratory testing that evaluates wind pressure performance characteristics for wall systems constructed with exterior insulating sheathing. This research and test activity will help to facilitate the ongoing use of non-structural sheathing options and provide a more in-depth understanding of how wall system layers perform in response to high windperturbations normal to the surface.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Finite-element-analysis model and preliminary ground testing of controls-structures interaction evolutionary model reflector

Results of two different nonlinear finite element analyses and preliminary test results for the final design of the Controls-Structures Interaction Evolutionary Model are presented. Load-deflection data bases are generalized from analysis and testing of the 16-foot diameter, dish shaped reflector. Natural frequencies and mode shapes are obtained from vibrational analysis. Experimental and analytical results show similar trends; however, future test hardware modifications and finite element model refinement would be necessary to obtain better correlation. The two nonlinear analysis procedures are both adequate techniques for the analysis of prestressed structures with complex geometries.

Reaves, Mercedes C.↗

A preliminary investigation of projectile shape effects in hypervelocity impact of a double-sheet structure

Impact tests of a sphere and several cylinders of various masses and fineness ratios, all of aluminum, fired into an aluminum double-sheet structure at velocities near 7 km/sec, show that a cylinder, impacting in the direction of its axis, is considerably more effective as a penetrator than a sphere. Impacts of three cylinders of equal mass, but different fineness ratios, produced holes through the structures' rear sheet, whereas impact of a sphere of the same mass did not. Moreover, it was found that to prevent rear-sheet penetration, the mass of the 1/2-fineness-ratio cylinder had to be reduced by a factor greater than three. Further tests wherein the cylinder diameter was held constant while the cylinder length was systematically reduced showed that a cylinder with a fineness ratio of 0.07 and a mass of only 1/7 that of the sphere was still capable of producing a hole in the rear sheet.

Morrison, R. H.↗

Experimental high gradient testing of a 17.1 GHz photonic band-gap accelerator structure

We report the design, fabrication and high gradient testing of a 17.1 GHz Photonic Band Gap accelerator structure. Photonic band-gap (PBG) structures are promising candidates for electron accelerators capable of high-gradient operation because they have the inherent damping of high order modes required to avoid beam breakup instabilities. The 17.1 GHz PBG structure tested was a single cell structure composed of a triangular array of round copper rods of radius 1.45 mm spaced by 8.05 mm. The test assembly consisted of the test PBG cell located between conventional (pillbox) input and output cells, with input power of up to 4 MW from a klystron supplied via a TM01 mode launcher. Breakdown at high gradient was observed by diagnostics including reflected power, downstream and upstream current monitors and visible light emission. The testing procedure was first benchmarked with a conventional disc-loaded waveguide structure, which reached a gradient of 87 MV/m at a breakdown probability of 1.19 × 10^-1 per pulse per meter. The PBG structure was tested with 100 ns pulses at power levels of less than 90 MV/m in order to limit the surface temperature rise to 120 K. The PBG structure reached up to 89 MV/m at a breakdown probability of 1.09×10^-1 per pulse per meter. These test results show that a PBG structure can simultaneously operate at high gradients and low breakdown probability, while also providing wakefield damping.

43 PARTICLE ACCELERATORS↗

Status of High Power Tests of Normal Conducting Single-Cell Structures

We report the results of ongoing high power tests of single-cell standing wave structures. These tests are part of an experimental and theoretical study of rf breakdown in normal conducting structures at 11.4 GHz. The goal of this study is to determine the maximum gradient possibilities for normal-conducting rf powered particle beam accelerators. The test setup consists of reusable mode launchers and short test structures powered by SLACs XL-4 klystron. The mode launchers and structures were manufactured at SLAC and KEK and tested at the SLAC klystron test laboratory.

43 PARTICLE ACCELERATORS↗

Fabrication and Testing of Complex Silicon Carbide Composite Structures

The ability to fabricate larger complex silicon carbide composites is an enabling technology for advanced reactors. Processing techniques to make complex SiC/SiC structures must be versatile enough to facilitate fabrication of both very large components (>1 m), as well as very small feature sizes (<1 mm), minimize the amount of machining required to complete the final part, and must also provide composite material with similar performance to bulk properties previously established for planar SiC/SiC composite material. This paper presents results on fabrication of complex silicon carbide structures and targeted testing aimed specifically at understanding how complex features impact composite performance. Silicon carbide (SiC) and silicon carbide matrix, silicon carbide fiber-reinforced composites (SiC/SiC) are a strong candidate for cladding and core structure used in advanced reactor concepts such as General Atomics' (GA) Energy Multiplier Module (EM{sup 2}) as well as accident tolerant fuel (ATF) in LWRs. SiC retains its strength up to very high temperatures, is stable under irradiation, and shows favorable neutronics and oxidation resistance compared to alloy alternatives. However, unlike metals, SiC cannot be easily machined, formed or welded to make the more complex core components needed to fully realize the benefits of advanced high temperature reactors. TEP processing provides an appealing route to achieving SiC/SiC composite structures with enhanced feature complexity. This is a critical development in the maturation of SiC/SiC for in-core structural materials in advanced reactors. This processing route provides an avenue to make large, dense, complex structures. Experiments have shown retention of strength and pseudo-ductility with hole spacing as small as 4 mm with potential for still smaller feature spacing. The results indicate that feature spacing is not limited by processing effects, but instead by the fiber architecture. The lower limit of feature spacing will likely have implications on potential core loading limits in advanced nuclear reactors utilizing SiC/SiC. (authors)

36 MATERIALS SCIENCE↗

Critical Joints in Large Composite Primary Aircraft Structures. Volume 3: Ancillary Test Results

A program was conducted to develop the technology for critical structural joints for composite wing structure that meets all the design requirements of a 1990 commercial transport aircraft. The results of a comprehensive ancillary test program are summarized, consisting of single-bolt composite joint specimens tested in a variety of configurations. These tests were conducted to characterize the strength and load deflection properties that are required for multirow joint analysis. The composite material was Toray 300 fiber and Ciba-Geigy 914 resin, in the form of 0.005 and 0.01 inch thick unidirectional tape. Tests were conducted in single and double shear for loaded and unloaded hole configurations under both tensile and compressive loading. Two different layup patterns were examined. All tests were conducted at room temperature. In addition, the results of NASA Standard Toughness Test (NASA RP 1092) are reported, which were conducted for several material systems.

Bunin, Bruce L.↗

High-R Walls for New Construction Structural Performance: Wind Pressure Testing

This technical report is focused primarily on laboratory testing that evaluates wind pressure performance characteristics for wall systems constructed with exterior insulating sheathing. This research and test activity will help to facilitate the ongoing use of non-structural sheathing options and provide a more in-depth understanding of how wall system layers perform in response to high wind perturbations normal to the surface.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Simulation of a spatial, servo-hydraulic test facility for space structures

In this paper different control concepts for servo-hydraulic test facilities are derived using exact linearization techniques. Based on different linear and nonlinear models of the test table and the actuator dynamics several nonlinear controllers of different complexity are derived. The closed loop system performance of the controlled servo-hydraulic test facility is tested in various computer simulations using both, standard test signals and large test signals as system inputs. The simulation results turn out, that in case of standard input signals the test facility controller must include a linear test table mechanics model and a nonlinear servo-hydraulic actuator model. Additional simulations demonstrate the robustness of the control concept selected for standard test signals with respect to variations of plant parameters.

Leimbach, K.-D.↗

Flow and Turbulence Control in a Boundary Layer Wind Tunnel Using Passive Hardware Devices

The Climatic Wind Tunnel (CWT) is a new experimental facility of the Institute of Theoretical and Applied Mechanics (ITAM) in Prague, Czech Republic. It is uniquely able to replicate precipitation and freezing effects on structural models in the climatic test section, and simultaneously perform aerodynamic and aeroelastic tests on structural models in the aerodynamic test section. Extensive measurements are carried out to investigate airflow and turbulence characteristics in the empty aerodynamic test section. Capability to experimentally simulate the atmospheric boundary layer (ABL) is studied using castellated barrier wall, Counihan vortex generators, and surface roughness elements. An individual influence of each of these passive hardware devices is separately tested as well, as they are commonly used combined, and their individual contributions to the ABL model characteristics are not well known. The analysis is based on hot-wire anemometer measurements carried out at various cross sections in the aerodynamic test section of the CWT. Experimental results are reported as mean velocity and turbulence intensity fields for the empty aerodynamic test section without passive hardware devices. Vertical profiles of mean velocity, turbulence intensity, and turbulence length scales, as well as power spectral density of velocity fluctuations, are reported for the ABL small-scale model. The barrier is observed to cause a decrease in flow velocity and an increase in turbulence close to surface. Vortex generators enhance turbulence throughout the entire height range under scope. Increased turbulence and decreased flow velocity are particularly exhibited close to surface due to surface roughness. Influence of each of the studied passive hardware devices on flow and turbulence is quantified in a dimensionless form to allow for separately accounting for their effects.

42 ENGINEERING↗