Search NASA⌕ Search

SEARCH · Search NASA

Results for “DUCTILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

The effect of Ti content on age hardening and mechanical properties of uranium-titanium alloys

Here, the effect of Ti content on age hardening and the resulting mechanical properties are described for -quenched U-Ti alloys containing 0.3 wt.% to 2.0 wt.%Ti. Age hardening occurs between ~250°C and ~450°C. Overaging occurs at higher temperatures by cellular decomposition. Age hardening kinetics suggest that different mechanisms occur depending on Ti content and initial microstructure. Strengthening in 'a acicular martensites begins by the formation of Ti clusters which evolve into thin U 2 Ti disc shaped precipitates and later mature into continuous U 2 Ti rods beginning at peak hardness. The mechanism of hardening in 'b banded martensite is more elusive, as significant hardening occurs where atomic mobility is lower than that required for precipitate formation, similar to that reported for age hardening in ''b banded martensite in U-6%Nb. The activation energy for aging varies with Ti content and microstructure. In fully martensitic alloys containing 0.75% to 2.0%Ti it is in the vicinity of ~44 kcal/mole (184 kJ/mole). But it is lower in alloys containing less than 0.6%Ti where quenched microstructures are less than fully martensitic. Tensile ductility is high prior to aging, decreases with age hardening, is effectively zero at peak hardness, and remains low in overaged conditions. Attractive combinations of strength and ductility are best obtained in alloys containing 0.6% to 1.0%Ti which have been partially aged to fractional hardening levels no greater than ~0.6. This corresponds to the very early stages of aging, associated with clustering and the earliest stages of U 2 Ti disc formation. Alloys containing 0.45%Ti or less are not as responsive to age hardening. Alloys containing 1.5% and 2.0%Ti can be aged to higher strengths, but extreme quench rate sensitivity prevents them from being effectively heat treated in realistic section thicknesses.

36 MATERIALS SCIENCE↗

The impact of chromium coatings on Zircaloy cladding deformation behavior under reactivity-initiated accident-like mechanical loading conditions

A reactivity-initiated accident (RIA) occurs when a control rod ejection or control blade drop causes an increase in the fission rate. The injection of energy results in an increase in fuel temperature which in turn causes rapid thermal expansion of the fuel pellet. This thermal expansion may result in pellet-cladding mechanical interaction (PCMI) in which the fuel imparts a mechanical strain to the cladding. PCMI may cause the cladding to fail, and thus, the mechanical response of cladding due to PCMI must be investigated when characterizing new cladding materials. Chromium-coated Zircaloy-4 is a near-term accident-tolerant fuel cladding that exhibits improved high-temperature oxidation resistance. Modified burst testing was utilized to experimentally simulate the effects of PCMI on both uncoated and chromium-coated Zircaloy cladding samples at hot zero power conditions. Samples were coated using either cold spraying or physical vapor deposition to understand the differences in behavior that the coating application method may cause. Digital image correlation was used to analyze images of the deforming specimens to extract the in-situ strain behavior of the cladding. The uncoated specimens burst at hoop strains ranging from 8.8 % to 17.2 %. The cold-spray chromium-coated Zircaloy specimens burst at hoop strains of 7.0 % to 11.0 %. The physical vapor deposition coated tubes burst at hoop strains of 9.1 % to 11.5 %. These results indicate that the chromium coating causes a loss in the ductility of the cladding. Furthermore, the higher burst hoop strains of the physical vapor deposition-coated samples relative to the cold-spray samples indicate that the cold-spraying technique causes more of a loss in ductility than physical vapor deposition. All samples burst at higher hoop strains than those expected to occur in an RIA for fresh cladding.

Accident-tolerant fuel↗

Monotonic testing of single shear-plane CLT-to-CLT joint with hardwood dowels

Reducing embodied carbon emissions in buildings and striving for carbon neutrality through sustainable design has become a primary goal in the construction industry. The industry is expanding its use of wood-engineered products, such as cross-laminated timber (CLT) to achieve those sustainability goals. Furthermore, replacing steel fasteners with lower embodied carbon alternatives is gaining increased attention in timber engineering. This paper aims to quantify the mechanical behavior of single shear-plane CLT-to-CLT joints using hardwood dowels. The study includes 154 single shear-plane experimental tests with four different CLT species, two hardwood dowel species, and two dowel diameters. Further, the test specimens were subjected to cyclic and monotonic loading until failure, and mechanical properties such as yielding and ultimate strength, serviceability and yielding stiffness, and ductility were quantified. The hardwood dowel CLT-to-CLT joints demonstrated high strength with up to 10.3 kN (2.3 kips) capacity per dowel and lateral stiffness of up to 5.2 kN/mm (30.8 k/in) per dowel. This strength and stiffness are roughly equivalent to or exceed values for mass timber wood screws, making hardwood dowels a good alternative. In addition, the observed mean ductility of joints ranged from 2.4 to 4.5. Finally, analytical equations for the joints' yielding strength, lateral serviceability stiffness, and yielding stiffness were derived with non-linear regression analysis and validated using the experimental test results.

42 ENGINEERING↗

Facile synthesis and electrochemical characterization of Sn{sub 4}Ni{sub 3}/C nanocomposites as anode materials for lithium ion batteries

Sn{sub 4}Ni{sub 3}/C nanocomposites were synthesized by a pyrolyzing-annealing two-step strategy. The phase structure, carbon content and morphology of the nanocomposites were investigated. The results reveal that the crystallinity, carbon structure and purity were enhanced obviously after heat-treatment. Electrochemical performance was evaluated by cyclic voltammograms (CV), galvanostatic discharge/charge and electrochemical impedance spectra (EIS). The annealed Sn{sub 4}Ni{sub 3}/C powders deliver an initial charge capacity of 525.2 mA h g{sup -1}, 400 mA h g{sup -1} over 10 cycles at 36 mA g{sup -1}, >300 mA h g{sup -1} after 40 cycles at 72 mA g{sup -1} and maintain 240 mA h g{sup -1} for 40 cycles at 150 mA g{sup -1}. TEM investigation of the cycled electrodes shows the discharge/charge process neither destroyed the structure of nanocomposites nor changed the crystallinity of the materials. So the high capacity and stable cyclability are ascribed to the synergetic effect of ductile nickel and conductive carbon constituent and the influence of heat-treatment. - Graphical abstract: TEM image of the annealed Sn{sub 4}Ni{sub 3}/C nanocomposites reveals that the crystallized Sn{sub 4}Ni{sub 3} nanoparticles are dispersed in the carbon layer. The synergetic effect of ductile Ni and carbon layer is beneficial to buffer the volume change of Sn during discharge/charge process, thus improving the electrochemical performance when used as anode materials for lithium ion batteries. Highlights: Black-Right-Pointing-Pointer Sn{sub 4}Ni{sub 3} nanoparticles well dispersed in carbon matrix were successfully fabricated. Black-Right-Pointing-Pointer Stable cycling property was achieved due to the synergetic effect of Ni and carbon. Black-Right-Pointing-Pointer The cycling process did not change the structure and crystallinity of the materials.

36 MATERIALS SCIENCE↗

Characterization of microstructures and mechanical properties of Inconel 617/310 stainless steel dissimilar welds

The microstructure and mechanical properties of Inconel 617/310 austenitic stainless steel dissimilar welds were investigated in this work. Three types of filler materials, Inconel 617, Inconel 82 and 310 austenitic stainless steels were used to obtain dissimilar joint using the gas tungsten arc welding process. Microstructural observations showed that there was no evidence of any possible cracking in the weldments achieved by the nickel-base filler materials. The welds produced by 617 and 310 filler materials displayed the highest and the lowest ultimate tensile strength and total elongation, respectively. The impact test results indicated that all specimens exhibited ductile fracture. Among the fillers, Inconel 617 exhibited superlative fracture toughness (205 J). The mechanical properties of the Inconel 617 filler material were much better than those of other fillers. - Research Highlights: {yields} A fine dendritic structure was seen for the Inconel 617 weld metal. {yields} A number of cracks were initiated when the 310 SS filler metal was used. {yields} All welded samples showed ductile fracture. {yields} The Inconel 617 filler material presents the optimum mechanical properties.

36 MATERIALS SCIENCE↗

Microstructural response to heat affected zone cracking of prewelding heat-treated Inconel 939 superalloy

The microstructural response to cracking in the heat-affected zone (HAZ) of a nickel-based IN 939 superalloy after prewelding heat treatments (PWHT) was investigated. The PWHT specimens showed two different microstructures: 1) spherical ordered {gamma} Prime precipitates (357-442 nm), with blocky MC and discreet M{sub 23}C{sub 6} carbides dispersed within the coarse dendrites and in the interdendritic regions; and 2) ordered {gamma} Prime precipitates in 'ogdoadically' diced cube shapes and coarse MC carbides within the dendrites and in the interdendritic regions. After being tungsten inert gas welded (TIG) applying low heat input, welding speed and using a more ductile filler alloy, specimens with microstructures consisting of spherical {gamma} Prime precipitate particles and dispersed discreet MC carbides along the grain boundaries, displayed a considerably improved weldability due to a strong reduction of the intergranular HAZ cracking associated with the liquation microfissuring phenomena. - Highlights: Black-Right-Pointing-Pointer Homogeneous microstructures of {gamma} Prime spheroids and discreet MC carbides of Ni base superalloys through preweld heat treatments. Black-Right-Pointing-Pointer {gamma} Prime spheroids and discreet MC carbides reduce the intergranular HAZ liquation and microfissuring of Nickel base superalloys. Black-Right-Pointing-Pointer Microstructure {gamma} Prime spheroids and discreet blocky type MC carbides, capable to relax the stress generated during weld cooling. Black-Right-Pointing-Pointer Low welding heat input welding speeds and ductile filler alloys reduce the HAZ cracking susceptibility.

36 MATERIALS SCIENCE↗

A study of the deformation and failure mechanisms of protective intermetallic coatings on AZ91 Mg alloys using microcantilever bending

In this study, a nanoindentation-based microcantilever bending technique was utilized to investigate the interfacial properties of a β-Mg{sub 17}Al{sub 12}/AZ91 Mg alloy film/substrate system under tensile loading conditions. Finite element analysis (FEA) was first undertaken to optimise the design of cantilever structures for inducing high tensile stresses at the interface. Cantilevers consisting of a necked region or notch at the interface were determined to be the most successful designs. Microcantilevers containing the β-Mg{sub 17}Al{sub 12}/AZ91 interface were then made using focused ion beam (FIB) milling technique. Necks were made in the cantilevers to intensify the tension at the interface and notches were used to introduce a stress concentration to the interface. During bending, the cantilevers were deflected to failure. Subsequent analysis of the deformed cantilevers using electron microscopies revealed that plastic deformation, and subsequent ductile rupture, of the AZ91 phase was the dominant failure mechanism. When the β-Mg{sub 17}Al{sub 12}/AZ91 film/substrate system was subjected to tension, the softer AZ91 phase failed prior to interfacial delamination, demonstrating that the strength of the interface exceeded the stresses that caused ductile failure in the substrate material. - Highlights: •Microcantilever bending was used to study the property of film/substrate interface. •FEA was used to optimise cantilever design for achieving high interfacial tension. •The intermetallic coatings on AZ91 substrate have strong interfacial adhesion.

36 MATERIALS SCIENCE↗

Effect of non-axisymmetric arc on microstructure, texture and properties of variable polarity plasma arc welded 5A06 Al alloy

Highlights: • Variable polarity plasma arc welding of 5A06 Al alloy was carried out under the condition of non-axisymmetric arc. • Deformation bands formed in the weld joint were due to microstructural inhomogeneities. • Tensile fracture occurred along the deformation bands in the TZ/HAZ fusion boundary on the side of “lower arc”. • The weld zones are harder than the BM due to dislocation sub-structure, deformation bands and ultrafine subgrain. - Abstract: Microstructure, texture and mechanical properties in the weld joint of variable polarity plasma arc welding of 5A06 Al alloy under the condition of non-axisymmetric arc have been investigated. The weld joint are characterized by elongated structure in the base material (BM), the heat affected zone (HAZ) and the transition zone (TZ) and equiaxed structure in the fusion zone (FZ). Microstructure of the weld joint is asymmetrical and inhomogeneous leading to deformation bands. Deformation texture and recrystallization texture were developed in the weld zones. The FZ center was dynamic recrystallized due to severe deformation. Materials in the TZ have undergone dynamic recovery. The weld zones are harder than the BM due to dislocation sub-structure, deformation bands and ultrafine subgrains. Microhardness distribution was homogeneous in the regions without deformation bands. Tensile fracture occurred along the deformation bands on the side of “lower arc” exhibiting ductile fracture, while the BM is less ductile.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties development of micro channel tubes in extrusion, rolling and brazing

Highlights: • Rolling and brazing greatly affect the properties of micro-channel tubes (MCTs). • The properties of MCTs are investigated by the evolution of the microstructure. • Strength is decreased by 47% at 5%-rolling reduction ratio and 3-minute brazing. • Ductile fracture mode is observed by OM at failure of MCTs under inner pressure. - Abstract: In addition to extrusion, the post-processing of rolling and brazing has significant effect on the mechanical properties of multi-port tubes. The aluminum micro channel tubes, especially the seam welding zone in the internal webs, are investigated in terms of mechanical tests, microstructure characterization, and finite element analysis. The effect of the post-process of rolling are quantified by varying amount of rolling reduction ratios. Tensile strength and pressure bearing capacity are determined by tensile tests and burst pressure tests, respectively. The evolution of the microstructure within the seam wielding zone is characterized by Electron backscattered diffraction (EBSD) and optical microscopy (OM). The fracture profile observed by OM indicates ductile fracture mode. The pressure bearing capacity is reduced by ~47% at 5% reduction ratio of rolling followed by 3-minute brazing, where largest grains are obtained due to abnormal grain growth.

36 MATERIALS SCIENCE↗

Crystal rotation and microstructures in an aluminum single-slip system under tensile loading

Highlights: • The crystal rotation angle with the progression of ductile damage was larger in the vertical plane than that in the horizontal plane. In the measurement along 110, the relative rotation angle was the maximum at the intersection of 111 and 110. • The integrated intensity and the FWHM decreased near the notch (from 0 to 0.3 mm) as well as at the intersection of 110 and 111 in the measurement along 110. • The dislocation cell size and the dislocation density decreased at the intersection of 111 and 110 in the measurement of 110 for ε = 5%. This behavior was attributed to the strain energy being released by the rotation of the dislocation cell. We experimentally investigated the rotation angle of the (220) plane in an aluminum single-slip system in which the angles of 110 and 111 in the single crystal were 45° relative to the tensile loading direction. Crystal rotation was investigated at several spots (50 × 50 μm) along 110 and 111 using synchrotron radiation white X-rays at the BL28B2 beamline of super photon ring-8. In measurements along the 110 axis, at an applied strain of ε = 5%, the relative crystal rotation of (220) in the vertical plane increased from 0.850° to 5.438° in the range of 0.9 to 1.4 mm. We observed the microstructure using a transmission electron microscope and verified the size of the dislocation cells or subgrains at each spot along 110. The fundamental local crystallography revealed in this work should be helpful in establishing a method for evaluating ductile damage in materials.

36 MATERIALS SCIENCE↗

Enhanced mechanical properties of carbon-doped FeNiMnAlCr high entropy alloy via hot-rolling

This work demonstrates an improvement in the mechanical performance of the high entropy alloy Fe 40.4 Ni 11.3 Mn 34.8 Al 7.5 Cr 6 containing 1.1 at. % carbon (CHEA) by hot-rolling followed by annealing at 1323 K. The microstructure was examined using scanning electron microscopy, electron backscatter diffraction, X-ray diffraction, and transmission electron microscopy. Room-temperature tensile tests were used to assess the alloy's mechanical properties. The presence of dense dislocation walls indicate that the alloy has not fully recrystallized and, moreover, the deformation substructure and the large fraction of Σ3 twin boundaries contribute to the high room temperature yield strength (~523 MPa). Despite the presence of substantial dislocation density, the annealed, hot-rolled CHEA displays an improvement in elongation to fracture (~33%) compared to the negligible ductility (< 2%) observed for the alloy after it has been simply annealed. Finally, the present work shows that hot rolling can produce good strength and ductility in the alloy while establishing the processing conditions necessary for the large-scale manufacture and utilization of its remarkable properties.

36 MATERIALS SCIENCE↗

Effect of aging on failure mechanism of Alloy 709 at various temperatures

Alloy 709 is a novel austenitic stainless steel with high temperature creep strength, weldability, and corrosion resistance. These properties make the material suitable for applications in the structure of next-generation nuclear power plants. Enduring high temperatures for an extended period of time in the harsh environments of a nuclear power plant results in thermal aging of the material. Therefore, it is imperative to study the effect of thermal aging on the microstructure and mechanical properties of Alloy 709 before its application in the next generation power plants. In this study, hot-processed (forged + rolled), annealed and quenched ingots of Alloy 709 are aged at 650 °C for 2000 h in air and then tested at various temperatures up to 850 °C in an in-situ heating-loading Scanning Electron Microscope (SEM) equipped with Energy Dispersive Spectroscopy (EDS) and Electron Backscatter Diffraction (EBSD). The effect of testing temperature and aging on microstructural evolutions during tensile testing of as-received and aged samples are studied. Furthermore, both as-received and aged samples displayed serrations and drop in ductility at elevated temperatures, due to the effect of dynamic strain aging (DSA). The occurrence of DSA activity was found within temperatures range of 500 °C–750 °C in as-received and 550 °C - 650 °C in aged samples. The aged samples showed less elongation accompanied by shallower dimples on the fractured surface, indicating less ductile failure mechanism compared to as-received samples. Failure mechanism observations on the fracture surface using SEM fractography are correlated to the observations made on the sample surface using in-situ SEM to achieve a complementary set of information to better understand the failure mechanism of this novel alloy.

36 MATERIALS SCIENCE↗

Exceptional strength and wear resistance in an AA7075/TiB 2 composite fabricated via friction consolidation

The friction consolidation method successfully reinforced aluminum 7075 alloy (AA7075) with high-volume fractions (12 and 24 vol%) of titanium diboride (TiB 2 ) by high pressure and severe plastic deformation at elevated temperatures. The consolidated AMCs have a uniform dispersion of submicron- and micron-sized TiB 2 particles in the AA7075 matrix, with significant refinement of the matrix grain size and the particles. The addition of TiB 2 significantly increases hardness by up to 50 %, Young’s modulus by up to 62 %, and ultimate tensile strength by up to 28 % to 672 MPa, while reducing ductility by 80 %. Wear resistance of 7075/24 vol% TiB 2 improves seven-fold compared to baseline, making it comparable to that of carburized steels. Microstructure-based finite element modeling provided a theoretical strength limit of ~730 MPa for the composites and indicated that high triaxiality in conjunction with severe equivalent plastic strain in a narrow area between the TiB 2 particles led to early fracture initiations, limiting the ductility.

36 MATERIALS SCIENCE↗

Pressure and doping dependent elastic and thermodynamical properties of Ga{sub 1-x}In{sub x}P mixed valent compounds

Using a phenomenological lattice model incorporating the long-range Coulomb and charge transfer caused by the deformation of the electron shells of the overlapping ions and the Hafemeister and Flygare type short-range overlap repulsion extended upto the second neighbor ions and the van der Waals (vdW) interaction, we present a comprehensive study to understand the effects of pressure on the elastic behavior as ductility (brittleness) and thermodynamical properties of Ga{sub 1-x}In{sub x}P. Estimated phase-transition pressure and the vast volume discontinuity in pressure-volume phase diagram confirm the structural phase transition from zinc blende (B3) to rock salt (B1) phase. From the elastic constants the Poisson's ratio {nu}, the ratio R{sub S/B} of S (Voigt averaged shear modulus) over B (bulk modulus), elastic wave velocity, average wave velocity and thermodynamical property Debye temperature is calculated. The Poisson's ratio {nu} and the ratio R{sub S/B} allows one to conclude that Ga{sub 1-x}In{sub x}P is brittle in zinc blende (B3) and ductile nature is inferred in sodium chloride (B1) phase. To our knowledge this is the first quantitative theoretical prediction of the doping and pressure dependent elastic properties for mixed valent Ga{sub 1-x}In{sub x}P compounds and still awaits experimental confirmations.

36 MATERIALS SCIENCE↗

Deformation behavior of a Co-Cr-Fe-Ni-Mo medium-entropy alloy at extremely low temperatures

In this work, we report the mechanical and microstructural characteristics of a medium-entropy alloy, Co 17.5 Cr 12.5 Fe 55 Ni 10 Mo 5 (atomic percent, at%) at cryogenic temperatures, down to a record low temperature of 0.5 K. The alloy exhibits excellent strength and ductility combined with a high strain-hardening rate in the entire temperature range investigated. Its property profile, including the yield strength, ultimate tensile strength, strain hardening capability, and absorbed mechanical energy, is better than those of most alloys and HEAs used in cryogenics. Within the interval of extremely low temperatures considered (0.5–4.2 K), the alloy exhibits several unusual features, including anomalies of the temperature dependence of the yield strength and tensile ductility, discontinuous plastic deformation (DPF), and a change in the propensity for the deformation-induced martensitic transformation. While the occurrence of these effects in the same temperature interval may be fortuitous, we hypothesize that they are interrelated and provide a tentative explanation of the observed phenomena on this basis.

36 MATERIALS SCIENCE↗

Unveiling the structural transformations in glassy solid electrolyte adapted to high-stress cycles

Brittleness of glass–ceramic and ceramic ion conductors is considered as a main roadblock for their implementation as electrolytes in solid-state batteries where the fractures often occur due to the pressure exerted by metallic lithium. In this regard, nano- and micro-scale ductility of the solid electrolyte allows reducing such pressure without formation of cracks. Among different types of solid state ion conductors, phosphate invert glasses seem to be promising in achieving such ductility. We report the mechanical behavior of lithium phosphorous oxynitride (LiPON) invert glass probed by static and cyclic nanoindentation. Repeated application of high intensity stress results in densification and shear deformation of material allowing LiPON to accommodate the ~ 22% nominal strain imposed by the nanoindenter without cracking. Ability to do this under repeated loading indicates robustness of LiPON when used in lithium metal batteries under cyclic charge and discharge. Using Raman spectroscopy with unsupervised K-means clustering we reveal pressure-induced formation of P 2 O 7 units which migrate to the periphery of the residual hardness impressions with cycling resulting in surface morphology of LiPON superficially similar to that of deformed bulk metallic glass.

36 MATERIALS SCIENCE↗

Primal interface debonding formulation for finite strain isotropic plasticity

In this work, a framework is developed for modeling ductile damage of nonlinear materials whose plastic deformation is characterized using rate independent classical plasticity. This method relies on the assumption that the free energy can be decomposed into elastic, plastic and damage parts. A thermodynamically consistent method is derived which satisfies the second law of thermodynamics in the Clausius–Duhem inequality form. The dissipation associated with plasticity takes place in the domain only, while damage dissipation is localized to the interface. The method is developed using Variational Multiscale ideas to obtain definitions of the interface fluxes within a primal formulation analogous to the Discontinuous Galerkin method, which ensures weakly vanishing interface gap prior to reaching a damage initiation criterion. The local nonlinear problem to calculate both plastic deformation gradient and damage variable follows an incremental approach similar to classical plasticity return mapping algorithm. This elastoplastic damage formulation is developed for material undergoing finite strain, and it naturally accommodates a trapezoidal traction separation law (TSL) whose shape can be varied to model either ductile interface behavior or brittle interface behavior. The formulation's performance is assessed through modeling a patch test and a compact tension specimen.

42 ENGINEERING↗