Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

In situ high-energy X-ray diffraction investigation of the micromechanical behavior of Fe-0.1C-10Mn-0/2Al steel at room and elevated temperatures

The micromechanical behavior of medium-Mn transformation-induced-plasticity (TRIP) steels with nominal chemical compositions of Fe-0.1C-10Mn (mass%) (0Al steel) and Fe-0.1C-10Mn-2Al (mass%) (2Al steel) fabricated by intercritical annealing 600 degrees C for 1 h and 650 degrees C for 1 h, respectively, was investigated using in situ high-energy X-ray diffraction (HE-XRD) with uniaxial tensile tests at 25 degrees C and 100 degrees C. We found that Liiders band propagation promoted lower volume fraction of austenite transformation to martensite in 0Al steel than 2Al steel at 25 degrees C while higher volume fraction of austenite transformation to martensite in 0Al steel than 2Al steel at 100 degrees C. Portevin-Le Chatelier (PLC) band propagation promoted higher volume fraction of austenite transformation to martensite in 0Al steel than 2Al steel during deformation at 25 degrees C and 100 degrees C. Moreover, the addition of Al obviously suppresses the formation of intermediate epsilon martensite during tensile deformation, thus the zigzag change in lattice strain of austenite was completely depressed in 2Al steel. Due to the controlled stability of metastable austenite, the 2Al steel demonstrated the best combination of ultimate tensile strength and total elongation at 25 degrees C.

36 MATERIALS SCIENCE↗
DOE OSTI2018

A brittle fracture mechanism in thermally aged duplex stainless steels revealed by in situ high-energy X-ray diffraction

A direct relationship between the microstructural evolution and macroscopic fracture behaviors of a thermally aged (at 475 °C for 400 h) duplex stainless steel (DSS) has been established with experimental results from atom probe tomography (APT), nanoindentation and in situ synchrotron-based high-energy X-ray diffraction (HE-XRD). Furthermore, the APT experiments demonstrate that ferrite in DSS spinodally decomposes into Cr-enriched and Cr-depleted domains during thermal aging, which leads to a severe hardening effect in ferrite. The lattice strain development during deformation acquired with the in situ HE-XRD measurements confirms the cleavage fracture of α{110} and α{200} ferrite grains aligned perpendicular to loading direction. The thermally aged DSS can be readily fractured by connecting the cleavage cracks in ferrite. Conclusively, the spinodal-decomposition-induced hardening in ferrite and the premature failure of ferrite control the final brittle fracture in the aged DSS.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ investigation of the deformation behaviors of Fe 20 Co 30 Cr 25 Ni 25 and Fe 20 Co 30 Cr 30 Ni 20 high entropy alloys by high-energy X-ray diffraction

In situ synchrotron-based high-energy X-ray diffraction (HE-XRD) technique was employed to investigate the mechanical behaviors and microstructural evolution of face-centered cubic (FCC) Fe 20 Co 30 Cr 25 Ni 25 and Fe 20 Co 30 Cr 30 Ni 20 high entropy alloys (HEAs) during tensile deformation. Fe 20 Co 30 Cr 30 Ni 20 HEA has a good combination of strength (ultimate tensile strength of 864 ± 35 MPa) and ductility (elongation of 0.627 ± 0.021). The HE-XRD investigation reveals that Fe 20 Co 30 Cr 30 Ni 20 HEA has the transformation-induced plasticity (TRIP) effect, which starts at a critical stress of ~555 MPa. Furthermore, transmission electron microscopy confirmed this deformation-induced new phase is hexagonal-close-packed structured ε-martensite, which follows an orientation relationship of {111} γ //(0001) ε , and (110) γ //[11 2 ¯ 0] ε with the FCC γ matrix. The observation of deformation twins in the deformed samples of the two studied HEAs proves that twinning-induced plasticity (TWIP) effect occurs in both HEAs. The combination of TRIP and TWIP effects lead to the high strength, large ductility and improved strain hardening behavior of Fe 20 Co 30 Cr 30 Ni 20 HEA.

36 MATERIALS SCIENCE↗
DOE OSTI2022

In-situ neutron diffraction investigation of two-stage martensitic transformation in a 13%Mn steel with serrated deformation

Two stage austenite →ε-martensite →α-martensite phase transformation, phase-specific lattice strain evolution and load sharing during tensile deformation of a 13%Mn hot-rolled austenitic steel are revealed by in-situ neutron diffraction. In conclusion, direct evidence is provided that serrated deformation behavior is attributed to discontinuous martensitic transformation.

Austenitic steel↗
DOE OSTI2022

The formation and evolution of Ni 2 Cr precipitates in Ni–Cr model alloys as a function of stoichiometry characterized by synchrotron x-ray diffraction

Ni-based alloys containing significant amounts of Cr, may precipitate new phases during long-term service at elevated temperatures. In Ni–Cr model alloys, the formation of Ni 2 Cr has been found to impact the material properties, including the strength and ductility after isothermal aging below the critical temperature of 590°C. In this work, we quantify the formation and evolution of long-range ordering in four Ni–Cr binary model alloys (Ni/Cr = 1.8, 2.0, 2.2, 2.4) after isothermal aging up to 10,000h at temperatures between 373 and 475°C. The alloys were characterized by hardness testing and synchrotron-based x-ray diffraction to quantify the impact of Ni 2 Cr phase fraction and precipitate size on mechanical properties. After 500h of isothermal aging, the formation of Ni 2 Cr was detected in all four alloys at 475°C. In the stochiometric alloy samples (Ni/Cr = 2.0), the formation of Ni 2 Cr was found after 500 and 3000h aging at 418 and 373°C, respectively. We found that the matrix lattice contraction and Ni 2 Cr phase fraction both saturate after early aging times. This is in stark contrast to the hardness and Ni 2 Cr precipitate size that both continue to increase with increasing aging time. Our results highlight that changes in hardness correlate linearly with Ni 2 Cr precipitate size rather than phase fraction. This important structure-property relationship can potentially help define Ni–Cr-based component lifetimes directly through an understanding of how Ni 2 Cr formation impacts strength and ductility. Here, we find that a precipitation hardening model for critical resolved shear stress with weakly coupled dislocations shows good agreement with the material property changes quantified from experimental measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effects of elevated temperature exposure on the residual stress state and microstructure of PVD Cr coatings on SiC investigated via in situ X-ray diffraction and transmission electron microscopy

Pure Cr coatings are being considered as corrosion-resistant layers for SiC-SiC f composite fuel cladding in light water reactors. The residual stress state and interdiffusion behavior of Cr coatings deposited on SiC substrates using bipolar high-power impulse magnetron sputtering (B-HiPIMS) and direct current impulse magnetron sputtering (DCMS) were studied using in situ X-ray diffraction experiments at 300 °C, 700 °C, and 1200 °C. After elevated temperature exposure, evolution of the coating microstructure and coating/substrate interdiffusion was characterized by transmission electron microscopy. The compressive residual stress of the dense B-HiPIMS coating at room temperature was gradually relieved at 300 °C, while the stress transitioned to a tensile state at 700 °C. Grain growth of the Cr coating and a Cr–SiC interdiffusion layer consisting of newly formed Cr–C and Cr–Si phases were observed in the B-HiPIMS coating after exposure at 700 °C. The phases in the interdiffusion layer were identified to be Cr 7 C 3 , Cr 3 Si, and Cr 5 Si 3 C x experimentally and by thermodynamic predictions. For the DCMS coating, however, changes in residual stress and microstructure at the elevated temperatures were limited by the inherent porosity and inhomogeneous structure of the as-deposited coating. At 1200 °C, both coating types interacted rapidly with the underlying SiC substrate in the early stages of the experiment. The results from this study suggest that the characteristics of the Cr coatings do not significantly change at the reactor operating temperature of 300 °C, while changes in microstructure and stress state are expected in off-normal conditions of 700 °C and 1200 °C. Finally the results from this study suggest the B-HiPIMS coating is best-suited as a protective coating for SiC fuel cladding.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding the asymmetric orientations and stress states in polycrystalline NiTi SMA by in-situ synchrotron-based high-energy X-ray diffraction

The stress-induced martensite transformations (SIMTs) dramatically affect the recoverable strain and mechanical response of polycrystalline NiTi. An in-depth understanding of the propagation manner and orientation preference of SIMTs is therefore crucial. Here, in this work, we present a unique asymmetric anisotropy of SIMTs and lattice strains induced by Lüders-type deformation in polycrystalline NiTi, achieved through a combination of in-situ synchrotron X-ray diffraction and uniaxial tensile loading and unloading experiments. Our experimental findings reveal that in polycrystalline NiTi under uniaxial deformation, the asymmetry of SIMTs is attributed to the inhomogeneous strain field caused by the Lüders-type mechanism. The asymmetrical SIMT starts with the forward Lüder band and disappears along with the backward Lüder band. The austenite with the favored orientation of $\langle$110$\rangle$ A //loading direction (LD) transformed and recovered back at a higher rate compared to other orientations during both loading and unloading.

36 MATERIALS SCIENCE↗
DOE OSTI2019

High temperature neutron diffraction investigation of U 3 Si 2

The U-Si system is actively undergoing studies due to its promise as a component of an accident tolerant nuclear fuel. In this work, the crystal structure of the U 3 Si 2 compound in the U-Si system was investigated as a function of temperature from room temperature to 1298 K for a sample of approximately 42.02 at.% Si composition and 1373 K for a sample with approximately 42.10 at.% Si using high temperature time-of-flight neutron diffraction on the High-Pressure Preferred Orientation (HIPPO) diffractometer at Los Alamos Neutron Science Center (LANSCE). The simultaneous Rietveld refinement of five histograms from the five HIPPO detector backs (40°, 60°, 90°, 120°, and 145°) provided datasets for the lattice parameters, anisotropic atomic displacement parameters, and atomic positions as a function of temperature. To explore the possibility of a homogeneity range, two sample compositions were analyzed, a 40.02 at.% Si (near stoichiometric) and a potentially hyperstoichiometric (40.10 at.% Si) sample. While minor differences in the anisotropic atomic displacement parameters between the two samples were observed, over the entire investigated temperature range no additional phases were found indicative of a single phase sample and the ability of the U 3 Si 2 compound to accommodate nonstoichiometry, suggesting that the U 3 Si 2 compound is not a line compound confirming previous determinations. However, the differences observed in the average coefficient of linear thermal expansion identified between the two compositions warrant future investigation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding the interaction of extension twinning and basal-plate precipitates in Mg-9Al using precession electron diffraction

Precession electron diffraction is used to characterize the interaction between ${10\bar{1}2}$ tensile twins and basal plate-like precipitates in a post-deformed, precipitate-dispersed Mg-9Al micropillar. We observed a heterogeneous distribution of precipitates in the micropillar sample, which enabled the study of the different stages involved in twin precipitate interactions. We show that twin nucleation was promoted, taking place on the surface, as well as from the interior of the micropillar. Twin tip propagation and twin growth were hindered by the precipitates. Twin tips either were arrested by precipitates and new twins formed on the other side of the precipitate, or continued to grow around the precipitate without the re-nucleation events. During twin thickening, the precipitates did not significantly alter the shear-dominant twin boundary migration mechanism, as evidenced by the relatively flat twin boundaries around the partially embedded precipitates. However, the twin boundary migration was retarded by the precipitates, especially in regions confined by closely-spaced precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Detector requirements and simulation results for the EIC exclusive, diffractive and tagging physics program using the ECCE detector concept

This article presents a collection of simulation studies using the ECCE detector concept in the context of the EIC’s exclusive, diffractive, and tagging physics program, which aims to further explore the rich quark–gluon structure of nucleons and nuclei. To successfully execute the program, ECCE proposed to utilize the detector system close to the beamline to ensure exclusivity and tag ion beam/fragments for a particular reaction of interest. Preliminary studies confirm the proposed technology and design satisfy the requirements. Further, the projected physics impact results are based on the projected detector performance from the simulation at 10 or 100 fb -1 of integrated luminosity. Additionally, insights related to a potential second EIC detector are documented, which could serve as a guidepost for future development.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

The diffractive contribution to deep inelastic lepton-proton scattering: Implications for QCD momentum sum rules and parton distributions

The cross section for deep inelastic lepton-proton scattering (DIS) ℓp→ℓ'p'X includes a diffractive deep inelastic (DDIS) contribution ℓp→ℓ'p'X, in which the proton remains intact with a large longitudinal momentum fraction x F greater than 0.9 and small transverse momentum. The DDIS events, which can be identified with Pomeron exchange in the t-channel, account for approximately 10% of all of the DIS events. Thus, when one measures DIS, one automatically includes the leading-twist Bjorken-scaling DDIS events as a contribution to the DIS cross section, whether or not the final-state proton p' is detected. In such events, the missing momentum fraction x p ' ~0.9 carried by the final-state proton p' in the DDIS events could be misidentified with the light-front momentum fraction carried by sea quarks or gluons in the protons' Fock structure. As we shall show in this article, the underlying QCD Pomeron-exchange amplitude which produces the DDIS events does not obey the operator product expansion nor satisfy momentum sum rules. Thus we conclude that the quark and gluon distributions measured in DIS experiments will be misidentified, unless the measurements explicitly exclude the DDIS events and that a correct determination of the parton distribution functions (PDFs) derived from the DIS data requires the explicit subtraction of the DDIS contribution from the full DIS cross section.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2017

Measuring Ti-7Al slip system strengths at elevated temperature using high-energy X-ray diffraction

Full stress tensors of over four hundred individual grains in a titanium alloy specimen (Ti-7Al) are tracked during continuous uniaxial deformation through the elasto-plastic transition at 355°C. The experiment is facilitated by a unique radiative heating furnace and load frame designed for in-situ high-energy X-ray diffraction measurements. Average strengths of multiple slip system families are calculated directly from the ensemble grain stress data. Overall, results show that elevated temperature lowers the strength of basal slip systems relative to prismatic slip systems, reduces the degree of flow softening due to precipitate shearing, and decreases the first-order pyramidal slip system work-hardening rate.

36 MATERIALS SCIENCE↗
DOE OSTI2017

In situ nanobeam electron diffraction strain mapping of planar slip in stainless steel

Nanobeam electron diffraction strain mapping has been used to measure the strain evolution in stainless steel under in situ deformation. As the amount of deformation increases, the leading dislocation of a planar slip band leaves behind a residual strain in the form of a small lattice expansion. Dislocation analysis confirmed that the dislocations involved were <011> type. Even though, the characteristic residual strain of planar slip has often been observed, it has never before been directly measured. Our conclusions provide a view into the dynamic mechanisms of planar slip, and showcase the possibilities of multidimensional in situ imaging.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The effect of helium implantation on the deformation behaviour of tungsten: X-ray micro-diffraction and nanoindentation

Here, the effect of helium-implantation-induced defects on deformation behaviour is examined by comparing spherical nano-indents in unimplanted and helium-implanted regions of a tungsten single crystal. Helium-implantation increases hardness and causes large pileups. 3D-resolved X-ray micro-diffraction uniquely allows examination of the complex lattice distortions beneath specific indents. In the ion-implanted material we find reduced lattice rotations and residual strains due to indentation, indicating a more confined plastic zone. Together, our observations suggest that helium-induced defects initially act as efficient obstacles to dislocation motion, but are weakened by the subsequent passage of dislocations, causing a reduction in work hardening capacity.

36 MATERIALS SCIENCE↗
DOE OSTI2018

In-situ synchrotron X-ray diffraction study of dual-step strain variation in laser shock peened metallic glasses

Atomic-structure evolution is significant in understanding the deformation mechanism of metallic glasses. Here, we firstly find a dual-step atomic strain variation in laser-shock-peened (LSPed) metallic glasses during compression tests by using in-situ synchrotron X-ray diffraction. Under low compressive load, LSP-deformed zone’s atomic-structure shows low Young’s Modulus (E); with load increase, atomic-structure are re-hardened, showing high E. An atomic deformation mechanism is proposed by using flow unit model, that LSP could induce interconnected flow units and 2 homogenize the atomic-structure. Furthermore, these interconnected flow units are metastable and start to annihilate during compressive loading, causing the dual-step atomic strain variation.

36 MATERIALS SCIENCE↗
DOE OSTI2018

An in situ neutron diffraction study of plastic deformation in a Cu 46.5 Zr 46.5 Al 7 bulk metallic glass composite

Micro-mechanical behaviors of a Cu 46.5 Zr 46.5 Al 7 bulk metallic glass composite in the plastic regime were investigated by continuous in situ neutron diffraction during compression. Three stages of the plastic deformation were observed according to the work-hardening rate. Here, the underlying natures of the work hardening, correlating with the lattice/microscopic strain evolution, are revealed for the three stages: (1) the initiation of shear bands, (2) the phase load transferring from the amorphous phase to the B2 phase and (3) the accelerated martensitic transformation and the work hardening of the polycrystalline phases promoted by the rapid propagation of the shear bands.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Signatures of the unique microstructure of additively manufactured steel observed via diffraction

A series of measurements were designed to gain confidence in the interpretation of the peak breadth in diffraction patterns collected from additively manufactured material, which has a novel microstructure in comparison to the well understood microstructure of wrought materials. Stainless steels made with two additive manufacturing techniques were compared to wrought material. Similar patterns observed in the scattering vector dependence for additively manufactured and deformed wrought materials suggested that the broadening in both materials was related to dislocations. Finally, this was confirmed by heat-treatment, during which both materials exhibited recovery due to the annealing of dislocations at the same temperature.

304L stainless-steel↗
DOE OSTI2018

Anisotropic lattice expansion determined during flash sintering of BiFeO 3 by in-situ energy-dispersive X-ray diffraction

BiFeO 3 has a Curie temperature (T C ) of 825 °C, making it difficult to sinter with conventional methods while maintaining the purity of the material, as unavoidably secondary phases appear at temperatures above T c . Flash sintering is a relatively new technique that saves time and energy compared to other sintering methods. BiFeO 3 was flash sintered at 500 °C to achieve 90% densification. In-situ energy dispersive X-ray diffraction (EDXRD) reflected that the material did not undergo any phase transformation, having been sintered well below the T C . Interestingly, anisotropic lattice expansion in the materialwas observed when the sample was exposed to the electric field.

36 MATERIALS SCIENCE↗