Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLUID MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Confinement-mediated phase behavior of hydrocarbon fluids: Insights from Monte Carlo simulations

The phase behavior of hydrocarbon fluids confined in porous media has been discussed to deviate significantly from that in the bulk environment due to the existence of sub-10nm pores. Though experiments and simulations have measured the bubble/dew points and sorption isotherms of hydrocarbons confined in both natural and synthetic nanopores, the confinement effects in terms of the strength of fluid-pore interactions tuned by surface wettability and chemistry have received comparably less discussion. More significantly, the underlying physics of confinement-induced phenomena remain obfuscated. In this work, we studied the phase behavior and capillary condensation of n-hexane to understand the effects of confinement at the molecular level. To systematically investigate the pore effects, we constructed two types of wall confinements; one is a structureless virtual wall described by the Steele potential and the other one is an all-atom amorphous silica structure with surface modified by hydroxyl groups. Our numerical results demonstrated the importance of fluid-pore interaction, pore size, and pore morphology effects in mediating the pressure-volume-temperature (PVT) properties of hydrocarbons. The most remarkable finding of this work was that the saturation pressure predicted from the van der Waals-type adsorption isothermal loop could be elevated or suppressed relative to the bulk phase, as illustrated in the graphical abstract. As the surface energy (i.e., fluid-pore interaction) decreased, the isothermal vapor pressure increased, indicating a greater preference for the fluid to exist in the vapor state. Sufficient reduction of the fluid-pore interactions could even elevate the vapor pressure above that of the bulk fluid.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Generation of ultra-fast cumulative water jets by sub-microsecond underwater electrical explosion of conical wire arrays

The results of experiments with underwater electrical explosion of modified conical arrays of copper and aluminum wires are presented. A pulsed generator producing a 550 kA-amplitude current with a 400 ns rise time was used in the explosion of the arrays. The array explosion generates water flows converging at the axis of the cone. This flow generates a fast-moving water jet with a velocity exceeding 1.8 × 10{sup 5 }cm/s, which was observed being ejected from the surface of the water covering the array. The positions of the water jet were measured by multiple-exposure fast framing imaging. In experiments, the apex angle of the array, the thickness of the water layer above the arrays, or the material of the wires was altered, which changed the resulting velocities and shapes of the emitted jets. A model that considers the converging stationary flow of a slightly compressible fluid is suggested. The velocities and shapes of the jets obtained by this model agree well with the experimentally measured jet velocities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

CFD-Enhanced Calibration of a Multihole Probe for Small Uncrewed Aircraft Systems

A robust calibration method with a 9-hole probe (9HP) for inertial wind vector measurements from a small uncrewed aircraft system (sUAS) is presented. Calibration accuracy is improved by using computational fluid dynamics (CFD) to estimate corrections, such as those for test section blockage, that are generally applied in wind tunnel testing. A method for estimating experimental bias is presented to account for flow variations over the pressure taps as the 9HP is repositioned in the test section. Installation effects from flow over the airframe and upwash produced by the wings are estimated from CFD simulations of the entire airframe at the expected cruise speed. An initial CFD analysis has demonstrated a quantifiable linear relationship between the measured and actual angle of attack as measured from the relative wind frame. In conclusion, the objective of these additional steps is to increase the accuracy of 9HP calibration.

54 ENVIRONMENTAL SCIENCES↗

Geometric state function for two-fluid flow in porous media

Models that describe two-fluid flow in porous media suffer from a widely recognized problem that the constitutive relationships used to predict capillary pressure as a function of the fluid saturation are nonunique, thus requiring a hysteretic description. As an alternative to the traditional perspective, we consider a geometric description of the capillary pressure, which relates the average mean curvature, the fluid saturation, the interfacial area between fluids, and the Euler characteristic. The state equation is formulated using notions from algebraic topology and cast in terms of measures of the macroscale state. Synchrotron-based x-ray microcomputed tomography and high-resolution pore-scale simulation is applied to examine the uniqueness of the proposed relationship for six different porous media. We show that the geometric state function is able to characterize the microscopic fluid configurations that result from a wide range of simulated flow conditions in an averaged sense. The geometric state function can serve as a closure relationship within macroscale models to effectively remove hysteretic behavior attributed to the arrangement of fluids within a porous medium. As a result, this provides a critical missing component needed to enable a new generation of higher fidelity models to describe two-fluid flow in porous media.

42 ENGINEERING↗

In-situ synthesis of magnetic (NiFe{sub 2}O{sub 4}/CuO/FeO) nanocomposites

In-situ synthesis of magnetic nanocomposites with (NiFe{sub 2}O{sub 4}/CuO/FeO) crystal phases has been done using a sol-gel method by taking a non-stoichiometric composition of the precursors. The average particle size of the nanocomposites was calculated using X-ray diffraction (XRD) and high resolution tunneling electron microscope (HR-TEM) and it turns out to be {approx}20 nm. The vibrating sample magnetometer (VSM) measurements demonstrate the ferromagnetic nature of the nanocomposites. The synthesized nanocomposite was used to prepare magnetic fluid using tetramethylammonium hydroxide as a surfactant and its stability in the solution was also discussed. -- Graphical abstract: Magnetic nanocomposites containing (NiFe{sub 2}O{sub 4}/CuO/FeO) phases having particle size {approx}17 nm were synthesized by a sol-gel method. The synthesized nanocomposites exhibit ferromagnetic nature with small value of coercivity.

36 MATERIALS SCIENCE↗

Flow around a corner in the water impact problem

In this work, we study the local flow in the vicinity of a flat sector of arbitrary angle α in the water impact problem as motivated by recent experimental observations in the author's laboratory. The key question is as to why the ejecta formed during the impact at zero deadrise angle is considerably higher along a straight edge of the sector compared to that near a sharp corner α < π, e.g., if the impacting body is a rectangular plate. Resolving this question is made possible by the discovered here mathematical equivalence of the problem to electromagnetic diffraction phenomena. The main result of the present study is the revealed and quantified influence of the geometry of a flat plate corner on the fluid flow around it, which also contributes to the understanding of certain three-dimensional effects in the water impact problem and provides a generalization of the classical two-dimensional results on the impact at zero deadrise angle. The offered theoretical solution is also qualitatively supported with the help of particle image velocimetry measurements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Numerical modeling of transient phenomena in the distant solar wind and in the heliosheath

In this paper we summarize our group's efforts to develop a self-consistent, data-driven model of the solar wind interaction with the local interstellar medium. In this model, we describe the motion of plasma with the MHD approach, while the transport of neutral atoms is described by either kinetic or multi-fluid equations. The model and its implementation in the Multi-Scale Fluid-Kinetic Simulation Suite (MS-FLUKSS) is thoroughly tested and validated by comparing our results with other models and spacecraft measurements. The model appears to be rather accurate in reproducing the Interstellar Boundary Explorer ribbon and the general features of the plasma flow available from the Voyager 1 and 2 in-situ data. In particular, the timing of the Voyager crossing of the termination shock is reasonably accurately reproduced without involving exotically strong interstellar magnetic field values. We added a turbulence model to our governing equations and started treating pickup ions as a separate fluid, which made it possible to greatly improve our ability to reproduce the proton temperature. We discuss the results of our modeling of corotating interaction regions, global merged interaction regions, and solar cycle effects. A possible explanation is provided for the low radial velocity measurements from Voyager 1.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The αs and θs in Rayleigh–Taylor and Richtmyer–Meshkov instabilities

The alphas (α b , α s ) and thetas (θ b , θ s ) are the essential parameters describing the asymptotic growth behavior of the mixing layer driven by Rayleigh–Taylor (RT) and Richtmyer–Meshkov (RM) instabilities at the interface between the fluids. Extensive simulations and experiments have been conducted in the determination of these parameters. The results depend on numerical algorithms, resolutions, and the accuracy of experimental measurements. In this article, we present a unique relationship between the alphas and thetas by applying a simple buoyancy-drag mixing model. Our first main result is that, for the same fluids, these parameters are not independent because they are fundamentally connected by physics principles and they all are functions of the drag coefficients of the fluids. As a consequence, the alphas and thetas are intrinsically coupled. All are functions of any single one of these. Additionally, our second main result is that the RT bubble growth rate (α b ) is determined by the bubble competition process – a merger model – at the edge of the mixing layer. Together, these two main results determine all the alphas and thetas by strictly theoretical reasoning. Applications to both hydro and laser driven experiments at OMEGA are presented.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Thermal-striping analysis methodology for sodium-cooled reactor design

Computational fluid dynamics simulations have been performed to study the applicability of engineering CFD methods for thermals striping analysis. Thermal striping is the fluctuating temperature profile in a solid caused by fluctuating fluid temperature, and the resulting fluctuating thermal stresses cause high cycle fatigue and eventual material failure. Here this study presents the methodology for thermal striping analysis that including a transient conjugate heat transfer RANS model and benchmark the results against a sodium triple jet experiment. The multiphysics calculations are implemented to analyze the thermal stresses in the solid domain caused by the coupled heat transfer between the fluid and solid domains. Validation data from a liquid sodium triple jet experiment include time-averaged temperature measurements and power spectra of the temperature signal. The numerical results agree well with these experimental measures, demonstrating key features such as the dominant frequency of temperature fluctuations. The applicability of a low-cost wall treatment method is demonstrated, enabling key computational savings. Finally, the performance of two finite element stress analysis software packages is compared, and the validity of the lower-cost method is confirmed. These results demonstrate the applicability of engineering methods for computational thermal striping calculations, enabling thermal striping estimations in large fluid systems such as the core of a Sodium-cooled nuclear reactor.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Oil and gas flow through fractures and along interfaces in well cement

A number of wells at the Strategic Petroleum Reserve (SPR) have shown sustained, positive pressure (referred to as sustained casing pressure or SCP) in the cemented annulus behind the production casing. To better understand how SCP may develop for SPR conditions, we conducted gas and oil flow tests on cement specimens with flaws including cement fractures and discrete interfaces along a cement-steel contact. Many specimens were tested initially with gas, followed by oil, and finally with gas again to identify how the fluid type may affect the flow through flaws in the well cement. Nitrogen was used as the gas, and silicone oil with properties similar to typical crude oil was used in most tests. One set of measurements were made with crude oil. Composite steel-cement specimen with corroded steel were also tested. For both gas and oil tests, the measured flow test data were used to interpret permeability and, assuming the cubic law for flow between parallel plates, the corresponding hydraulic aperture of the flaw. The hydraulic apertures for the flawed specimens ranged from about 20 to >100 μm, which corresponds to permeabilities of about 10 -14 to 10 -12 m 2 , respectively; these hydraulic apertures are consistent with the range of values interpreted from field measurements on leaky wells. Observed differences between the flow of gas and oil were attributed to a number of factors, including non-linear flow of gas, possible blocking of flow paths by solids within the crude oil, two-phase gas and oil flow and the presence of residual oil in the cement flaw. Furthermore, we determined that corroded steel itself is permeable. Using input values consistent with the gas and oil flow measurements, we conducted one-dimensional simulations of gas and oil flow through cemented annulus systems to investigate the role of flaw size and fluid type on the expected response (i.e., pressure build-up) in the annular cement.

02 PETROLEUM↗

Spherical torus equilibria reconstructed by a two-fluid, low-collisionality model

The two-fluid, low-collisionality equilibrium model [Ishida et al., Phys. Plasmas 17, 122507 (2010)] was applied to reconstruct the high-performance National Spherical Torus eXperiment (NSTX) [Bell et al., Phys. Plasmas 17, 082507 (2010)]. Profiles of the electron and ion temperatures, the toroidal flow, the density, and the magnetic field pitch angle of the reconstructed equilibrium fit well the measured profiles of NSTX shot 132484 at 0.7 s. The reconstructed equilibrium shows that (1) the global two-fluid effect is fairly large; (2) the perpendicular flow of both species differs significantly from the ExB drift; (3) local gradient scale lengths can be smaller than the ion inertial length especially on the outboard side; (4) the electrostatic potential varies along a given magnetic flux by as much as several percent of the electron temperature in the core region.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Feasibility Evaluation of Potential Stimulation Methods for Collab Experiment 3. Recommendation Report

In support of the Collab Project Milestone 1.4, INL is to submit a recommendation report describing feasible methods to investigate during Experiment 3 to DOE. This report fulfils this FY18Q1 SMART milestone. Twenty one potential methods were consideration for testing as part of Collab Experiment 3. The potential methods have been categorized as; Fracture Initiation, Stimulation Fluids, Stimulation Methods and Flow Control. The categories have been further divided into three general groups (e.g. high, medium, low) based on applicability to the scale of measurement at Collab (~10 meter) and it’s applicably to FORGE. The highest relevant methods (not necessary in order) are: 1) fracture initiation within the borehole, 2) use of slickwater fracturing fluids, 3) use of viscous fracturing fluids, 4) simultaneous stimulation of multiple wells, 5) use of energetic fluids to initiate larger fractures or connect a borehole to existing fractures, 6) injection of diverters to control short circuits and working fluid loss, 7) testing of borehole isolation techniques to control water flow pathways in the reservoir, and 8) use of multiple injection and production wells to characterize a fracture. Fractures created in Experiments 1 and 2 offer the opportunity to test engineering solutions to issues encountered in the stimulation process or during the fracture flow testing. An advantage of using these sites is that there would be a wealth of baseline characterization data for the site, and the borehole monitoring system and experimental infrastructure is already established and could possibly be reused. This suggested potential method list should be considered preliminary due to the timing of this report and the status of Collab Experiments 1 and 2 as well as the need for preliminary modeling to assess each of the proposed methods effectiveness.

15 GEOTHERMAL ENERGY↗

Quantifying Barotrauma Risk to Juvenile Fish during Hydro-turbine Passage

We introduce a method for hydro turbine biological performance assessment (BioPA) to bridge the gap between field and laboratory studies on fish injury and turbine engineering design. Using this method, a suite of biological performance indicators is computed based on simulated data from a computational fluid dynamics (CFD) model of a proposed hydro turbine design. Each performance indicator is a measure of the probability of exposure to a certain dose of an injury mechanism. If the relationship between the dose of an injury mechanism (stressor) and frequency of injury (dose-response) is known from laboratory or field studies, the likelihood of fish injury for a turbine design can be computed from the performance indicator. By comparing the values of the indicators from various turbine designs, engineers and biologists can identify the more-promising designs and operating conditions to minimize hydraulic conditions hazardous to passing fish. In this paper, the BioPA method is applied to estimate barotrauma induced mortal injury rates for Chinook salmon exposed to rapid pressure changes in Kaplan-type hydro turbines. Following the description of the general method, application of the BioPA to estimate the probability of mortal injury from exposure to rapid decompression is illustrated using a Kaplan hydro turbine at the John Day Dam on the Columbia River in the Pacific Northwest region of the USA. The estimated rates of mortal injury increased from 0.3% to 1.7% as discharge through the turbine increased from 334 to 564 m3/s for fish assumed to be acclimated to a depth of 5 m. The majority of pressure nadirs occurred immediately below the runner blades, with the lowest values in the gap at the blade tips and just below the leading edge of the blades. Such information can help engineers focus on problem areas when designing new turbine runners to be more fish-friendly than existing units.

computational fluid dynamics (CFD)↗

Production of monodisperse cerium oxide microspheres with diameters near 100 µm by internal-gelation sol–gel methods

Cerium dioxide microspheres with uniform diameters between 65 – 211 µm were fabricated using internal gelation sol-gel methods. Although uniform microspheres are produced for nuclear fuel applications with diameters above 300 µm, sol-gel microspheres with diameters of 50 - 200 µm have historically been made by emulsion techniques and had poor size uniformity [1, 2]. An internal gelation, sol-gel apparatus was designed and constructed to accommodate the production of small, uniform microspheres whereby cerium-containing solutions were dispersed into flowing silicone oil and heated in a gelation column to initiate solidification [3, 4]. Problems with premature feed gelation and microsphere coalescence were overcome by equipment modifications unique among known internal gelation setups. Microspheres were fabricated and sized in batches as a function of dispersing needle diameter and silicone oil flow rate in the two-fluid nozzle in order to determine the range of sizes possible and corresponding degree of monodispersity. Initial experiments with poor size uniformity were linked to microsphere coalescence in the gelation column prior to solidification as well as excessive flow rates for the cerium feed solution. Average diameter standard deviations as low as 2.23% were observed after optimization of flow rates and minimization of coalescence reactions.

cerium oxide↗

Separate effects identification via casting process modeling for experimental measurement of U–Pu–Zr alloys

Computational simulations of gravity casting processes for metallic U–Pu–Zr nuclear fuel rods have been performed using a design-of-experiments technique to determine the fluid flow, liquid heat transfer, and solid heat transfer parameters which most strongly influence the process solidification speed and fuel rod porosity. The results are used to make recommendations for the best investment of experimental time and effort to measure process parameters.

99 GENERAL AND MISCELLANEOUS↗

On the evolution of vortex rings with swirl

A laminar vortex ring with swirl, which has the meridional velocity component inside the vortex core, was experimentally generated by the brief fluid ejection from a rotating outlet. The evolution of the vortex ring was investigated with flow visualizations and particle image velocimetry measurements in order to find the influence of swirling flow in particular upon the transition to turbulence. Immediately after the formation of a vortex ring with swirl, a columnar strong vortex along the symmetric axis is observed in all cases of the present experiment. Then the characteristic fluid discharging from a vortex ring with swirl referred to as “peeling off” appears. The amount of discharging fluid due to the “peeling off” increases with the angular velocity of the rotating outlet. We conjectured that the mechanism generating the “peeling off” is related to the columnar strong vortex by close observations of the spatio-temporal development of the vorticity distribution and the cutting 3D images constructed from the successive cross sections of a vortex ring. While a laminar vortex ring without swirl may develop azimuthal waves around its circumference at some later time and the ring structure subsequently breaks, the swirling flow in a vortex ring core reduces the amplification rate of the azimuthal wavy deformation and preserved its ring structure. Then the traveling distance of a vortex ring can be extended using the swirl flow under certain conditions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Evidence of toroidally localized turbulence with applied 3D fields in the DIII-D tokamak

New evidence indicates that there is significant 3D variation in density fluctuations near the boundary of weakly 3D tokamak plasmas when resonant magnetic perturbations are applied to suppress transient edge instabilities. The increase in fluctuations is concomitant with an increase in the measured density gradient, suggesting that this toroidally localized gradient increase could be a mechanism for turbulence destabilization in localized flux tubes. Two-fluid magnetohydrodynamic simulations find that, although changes to the magnetic field topology are small, there is a significant 3D variation of the density gradient within the flux surfaces that is extended along field lines. This modeling agrees qualitatively with the measurements. The observed gradient and fluctuation asymmetries are proposed as a mechanism by which global profile gradients in the pedestal could be relaxed due to a local change in the 3D equilibrium. In conclusion, these processes may play an important role in pedestal and scrape-off layer transport in ITER and other future tokamak devices with small applied 3D fields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Chemical and isotopic evolution of flowback fluids from the Utica Gas Shale Play, Eastern Ohio USA

For this work, hydraulic fracturing flowback fluids were collected from two Utica/Point Pleasant well pads in eastern Ohio. One site was in the wet gas zone (UPPW), while the site ~50 km south consisted of four wells on the same pad in the dry gas zone (UPPS). Samples of input fluids also were collected before and during hydraulic fracturing. Flowback fluids are Na-Ca-Cl brines with total dissolved salt (TDS) concentrations that increase over several months from ~100 to 200 g/L. The slightly higher TDS of the dry gas fluids are in part due to recycled flowback used as input fluids, and in part due to lower volume of water used in hydraulic fracturing. Concentrations of most major ions (Ca 2+ , Mg 2+ , Na + , Sr2 + , Fe, Mn, Cl – , Br – ) are similar for the five wells sampled, although small but systematic changes occur in the major element ratios over time. Most notably, an increase in the Sr/Cl ratio corresponds to an increase in the 87 Sr/ 86 Sr ratio in the fluids, suggesting interactions with a more radiogenic Sr source in the subsurface. Dissolved Ba concentrations and Ra activities were different between the two sites, reflecting a high SO 4 2– fluid used at the UPPW site, and water-rock reactions occurring during hydraulic fracturing at the UPPS site. Water oxygen (δ 18 O) and hydrogen (δD) isotopes for input fluids used in the UPPW4 well and fresh water used for the UPPS wells fall on the Global Meteoric waterline (GMWL). Flowback fluids from both sites are relatively enriched in δ 18 O and δD compared to the input, but do not appear to follow a simple mixing trend, suggesting reaction and isotopic exchange with carbonates and fractionation due to imbibition in the rock. Cl isotopes, δ 37 Cl in the FP fluids varied from ~ –0.43 to +0.13‰, the largest variation was observed in the earlier stages of flowback, while in the later stages δ 37 Cl exhibited a small but systematic increase over time, suggesting diffusion control of isotopic composition. Some of the trace species measured (dissolved Fe, Mn, thiosulfate and organic acids) do not follow the same trends as the major ions, suggesting contributions from input fluids, or microbially mediated reactions are exerting control on their concentrations. Input water chemistry exerts an important control on the Sr and Ba concentrations in flowback water. High SO 4 2– in the input fluids used for hydraulically fracturing the wet gas well leads to precipitation of barite-celestite in flowback fluids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗