Search NASA⌕ Search

SEARCH · Search NASA

Results for “Inlets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Computational Evaluation of Inlet Distortion on an Ejector Powered Hybrid Wing Body at Takeoff and Landing Conditions

Due to the aft, upper surface engine location on the Hybrid Wing Body (HWB) planform, there is potential to shed vorticity and separated wakes into the engine when the vehicle is operated at off-design conditions and corners of the envelope required for engine and airplane certification. CFD simulations were performed of the full-scale reference propulsion system, operating at a range of inlet flow rates, flight speeds, altitudes, angles of attack, and angles of sideslip to identify the conditions which produce the largest distortion and lowest pressure recovery. Pretest CFD was performed by NASA and Boeing, using multiple CFD codes, with various turbulence models. These data were used to make decisions regarding model integration, characterize inlet flow distortion patterns, and help define the wind tunnel test matrix. CFD was also performed post-test; when compared with test data, it was possible to make comparisons between measured model-scale and predicted full-scale distortion levels. This paper summarizes these CFD analyses.

Wind Tunnel Testing↗

Supersonic Elliptical Ramp Inlet

A supersonic inlet includes a supersonic section including a cowl which is at least partially elliptical, a ramp disposed within the cowl, and a flow inlet disposed between the cowl and the ramp. The ramp may also be at least partially elliptical.

Adamson, Eric E.↗

Numerical Evaluation of an Ejector-Enhanced Resonant Pulse Combustor with a Poppet Inlet Valve and a Converging Exhaust Nozzle

A computational investigation of a pressure-gain combustor system for gas turbine applications is presented. The system consists of a valved pulse combustor and an ejector, housed within a shroud. The study focuses on two enhancements to previous models, related to the valve and ejector components. First, a new poppet inlet valve system is investigated, replacing the previously used reed valve configuration. Secondly, a new computational approach to approximating the effects of choked turbine inlet guide vanes present immediately downstream of the Ejector-Enhanced Resonant Pulse Combustor (EERPC) is investigated. Instead of specifying a back pressure at the EERPC exit boundary (as was done in previous studies) the new model adds a converging-diverging (CD) nozzle at the exit of the EERPC. The throat area of the CD nozzle can be adjusted to obtain the desired back pressure level and total mass flow rate. The results presented indicate that the new poppet valve configuration performs nearly as well as the original reed valve system, and that the addition of the CD nozzle is an effective method to approximate the exit boundary effects of a turbine present downstream of the EERPC. Furthermore, it is shown that the more acoustically reflective boundary imposed by a nozzle as compared to a constant pressure surface does not significantly affect operation or performance.

Computational Fluid Dynamics (CFD↗

Progress Towards Understanding Fan Inlet Implications of Top-Mounted Propulsion

Computational fluid dynamic (CFD) simulations were performed on an N+2 commercial supersonic transport aircraft design that featured top-mounted propulsion. The simulations were run at take-off conditions at both 0 degrees and 8 degrees angle of attack. The results showed little separation in around the inlets with inlet performance on par with an under-the-wing configuration. The next step will be to take these results and determine the acoustic impact of the top-mounted propulsion system.

Computational Fluid Dynamics (CFD)↗

Acoustic Directivity and Insertion Loss Measurements of Advanced Liners Installed the Inlet of the DGEN Aeropropulsion Research Turbofan

The NASA Glenn Research Center’s DGEN Aeropropulsion Research Turbofan (DART) is based on the Price Induction DGEN380—a small, ~500-lbf thrust class, high-bypass, geared-turbofan engine with a separate flow nozzle. The general characteristics of the DART make it an ideal candidate for utilization as a test bed for engine aeroacoustic research in a relevant performance environment. The DART was used to document the efficacy of acoustic liners installed in the inlet of the DGEN380. An advanced multi-degree-of-freedom liner (MDOF) was designed and tested, along with a traditional single-degree-of- freedom liner (SDOF), and those results compared to a hard-wall baseline inlet. Farfield acoustic data were acquired from an external array, evaluated, and reported here-in terms of overall, broadband, and tonal components of the insertion loss.

Noise Reduction↗

Design and Acoustic Efficacy of a Broadband Liner for the Inlet of the DGEN Aero-Propulsion Research Turbofan

Advanced fan designs (including higher bypass ratios) and shorter engine nacelles have highlighted a need for increased fan noise reduction over a broader frequency range. With these observations in mind, an acoustic liner optimization process has been developed to achieve improved broadband liner designs. A series of advanced liner design studies at increasing technology readiness levels have been conducted as the overall optimization methodology has been enhanced. As part of the analysis, the overall design and evaluation capability was extended such that external observer locations may be included in the optimization process. This enhancement will provide a much wider design space in designing advanced broadband liners. In this work, further validation was pursued through the fabrication and testing of two liner designs for the NASA Glenn DGEN Aero-propulsion Research Turbofan (DART). The DART was used to document the efficacy of acoustic liners installed in the inlet of the DGEN380. An advanced Multi-Degree of Freedom Liner was designed, fabricated, and tested, along with a traditional Single-Degree-of-Freedom Liner, and those results compared to a hardwall baseline inlet. Farfield acoustic data were acquired from and external array, evaluated and reported herein terms of overall, broadband, and tonal components of the insertion loss. The predicted attenuation results generally matched expected trends of the measured data for the conditions considered.

Liners↗

Design of an Advanced Inlet Liner for the Quiet Technology Demonstrator 3

The utilization of advanced fan designs (including higher bypass ratios) and shorter engine nacelles has highlighted a need for increased fan noise reduction over a broad frequency range. Thus, improved broadband liner designs must account for these constraints and take advantage of novel liner configurations. With these observations in mind, the development and assessment of a broadband acoustic liner optimization process has been pursued through a series of design and experimental studies. In this work, an advanced inlet liner was designed for a Boeing 737MAX-7 to reduce drag and to improve the broadband noise reduction relative to conventional liners in use today. Specifically, a three layer liner was designed, fabricated, and flight tested as part of the Quiet Technology Demonstrator 3 flight test program. Initial tonal predictions captured the behavior of the measured data very well and both prediction and measurements show an increased acoustic benefit at larger observer angles, particularly at the takeoff condition. Ultimately, flight test results showed the three degree-of-freedom liner to provide a 3.2 EPNdB cumulative inlet component benefit and a 0.7 EPNdB cumulative airplane benefit over the production liner. This excellent result provides valuable validation of the broadband liner design process, as well as the enhancements made to the overall approach. It also illustrates the value of the design process in concurrently evaluating various liner designs (i.e., SDOF, MDOF, etc.) and their application to various locations. Thus, the design process may be applied with further confidence to investigate novel liner configurations in future design studies.

Nark, Douglas M.↗

CFD Simulation of an Inward-Turning Supersonic Inlet Unstart at Flight Mach Number 1.7

Interest in inward-turning supersonic inlets renewed during NASA’s Commercial Supersonic Technology Project, as a means of reducing disturbances caused by propulsion integration. Inward-turning designs have the potential to greatly reduce the strength of shock waves emanating outward from the nacelle, and therefore their contribution to the overall sonic boom signature. For top-mounted, or over-wing installations, disturbances to aircraft aerodynamics are reduced. The nature of the inward-turning geometry results in a boundary-layer thickening effect, opposite that of the familiar thinning of an outward-turning cone boundary-layer. The application of a small amount of boundary-layer bleed at the throat has been shown to alleviate the negative effects of the boundary-layer on subsonic diffuser performance. Boundary-layer bleed, however, comes at the expense of increased complexity, and external disturbances at bleed exits that would partially defeat the purpose of the inward-turning scheme. Vortex generators were proposed as an alternative to bleed, and an initial CFD study of their effectiveness in this application forms the basis of the present work. A source-term model in the Wind-US CFD code was used to model the effects of an array of vortex generators placed at the entrance to the subsonic diffuser. Baseline results with no vortex generators compared favorably to previously reported results with no bleed at back-pressures near the design point, but stability margin in the present case was limited by a curious non-linear phenomena similar to unstart in mixed-compression inlets. While some improvement was noted with vortex generators, their effectiveness was diminished by the limited stability margin. A time-accurate calculation was subsequently performed to better understand this process. Results of this calculation are presented and instantaneous solutions compared with steady-state, subcritical results previously reported. The stability margin limitation is attributed to the use of a constant-pressure outflow boundary condition, which differed from that used in the prior simulations.

Pre-Compressor Cooling, Water Injection, Hypersoni↗

NASA “SuperFan”: Inlet+Fan Design for Landing and Take-Off (LTO) Noise Assessments

The commercial supersonic transport industry needs accurate prediction of landing and take-off propulsion fan noise. To enable improving these predictions, under contract to NASA, GE Aviation designed an inlet, two-stage fan with inlet guide vane, and flow path with separate flow nozzles for a turbofan engine relevant to a commercial supersonic transport application. This non-proprietary, but export controlled, geometry enables cross comparison of predictions, and is a step towards reducing prediction uncertainty. This presentation has the current status of this effort.

supersonic, fan, acoustic↗

CDC Bioreactor Configuration Method for Volume Level Control with Controlled Inlet and Outlet Flow

Environmental Control Life Support Systems and other microbiological biofilm studies often utilize small scale bioreactors. Among these options are the popular BioSurface CDC bioreactors, currently being utilized by Marshall Space Flight Center groups researching the impact of biofilms on life support systems. After a recent experimental regime, it was determined additional equipment could be added to augment the capabilities of the bioreactors. Previous research configurations such as ASTM E3161 – 18 relied on an outlet stream gravity draining from a side drain port located above sampling coupons. This limited applications to experimental conditions with a controlled inlet and uncontrolled outlet flow. With the introduction of a small single pole single throw (SPST) reed float switch, a peristaltic pump connected to the outlet drain and a chassis controller, the bioreactor is able to maintain a set level. The modification allows additional variables to be tested, including highly adjustable fill and flush cycles, bioreactor volume, draining and filling control. Once the configuration modifications were implemented through the installation of the new equipment, data was collected to ensure the stability of the level measurements. As the level control switch is a float switch, consideration was taken into account for effects of internal stirring speed, along with effects of inlet and outlet flow rate. Data presented in this study will illustrate the stability and effectiveness of the configuration changes in equipment made to the bioreactor. These configuration changes are proving an effective control method to conduct biofilm mitigation techniques for ECLSS hardware research. The controlled level capabilities allow for a constant drip feed flow rate into the bioreactors, a key aspect of the biofilm mitigation testing.

CDC Bioreactor↗

CDC Bioreactor Configuration Method for Volume Level Control with Controlled Inlet and Outlet Flow

Environmental Control Life Support Systems and other microbiological biofilm studies often utilize small scale bioreactors. Among these options are the popular BioSurface CDC bioreactors, currently being utilized by Marshall Space Flight Center groups researching the impact of biofilms on life support systems. After a recent experimental regime, it was determined additional equipment could be added to augment the capabilities of the bioreactors. Previous research configurations such as ASTM E3161-21 relied on an outlet stream gravity draining from a side drain port located above sampling coupons. This limited applications to experimental conditions with a controlled inlet and uncontrolled outlet flow. With the introduction of a small single pole single throw (SPST) reed float switch and a peristaltic pump connected to the outlet drain and a chassis controller, the bioreactor is able to maintain a set level. The modification allows additional variables to be tested, including highly adjustable fill and flush cycles, bioreactor volume, draining and filling control. Once the configuration modifications were implemented through the installation of the new equipment, data was collected to ensure the stability of the level measurements. As the level control switch is a float switch, consideration was taken into account for effects of internal stirring speed, along with effects of inlet and outlet flow rate. Data presented in this study will illustrate the stability and effectiveness of the configuration changes in equipment made to the bioreactor. These configuration changes have demonstrated control method to conduct biofilm mitigation techniques for ECLSS hardware research. The controlled level capabilities allow for a constant drip feed flow rate into the bioreactors, a key aspect of the biofilm mitigation testing.

CDC Bioreactor↗

CDC Bioreactor Configuration Method for Volume Level Control with Controlled Inlet and Outlet Flow

Environmental Control Life Support Systems and other microbiological biofilm studies often utilize small scale bioreactors. Among these options are the popular BioSurface CDC bioreactors, currently being utilized by Marshall Space Flight Center groups researching the impact of biofilms on life support systems. After a recent experimental regime, it was determined additional equipment could be added to augment the capabilities of the bioreactors. Previous research configurations such as ASTM E3161-21 relied on an outlet stream gravity draining from a side drain port located above sampling coupons. This limited applications to experimental conditions with a controlled inlet and uncontrolled outlet flow. With the introduction of a small single pole single throw (SPST) reed float switch and a peristaltic pump connected to the outlet drain and a chassis controller, the bioreactor is able to maintain a set level. The modification allows additional variables to be tested, including highly adjustable fill and flush cycles, bioreactor volume, draining and filling control. Once the configuration modifications were implemented through the installation of the new equipment, data was collected to ensure the stability of the level measurements. As the level control switch is a float switch, consideration was taken into account for effects of internal stirring speed, along with effects of inlet and outlet flow rate. Data presented in this study will illustrate the stability and effectiveness of the configuration changes in equipment made to the bioreactor. These configuration changes have demonstrated control method to conduct biofilm mitigation techniques for ECLSS hardware research. The controlled level capabilities allow for a constant drip feed flow rate into the bioreactors, a key aspect of the biofilm mitigation testing.

CDC Bioreactor↗

CDC Bioreactor Configuration Method for Volume Level Control with Controlled Inlet and Outlet Flow

Environmental Control Life Support Systems and other microbiological biofilm studies often utilize small scale bioreactors. Among these options are the popular BioSurface CDC bioreactors, currently being utilized by Marshall Space Flight Center groups researching the impact of biofilms on life support systems. After a recent experimental regime, it was determined additional equipment could be added to augment the capabilities of the bioreactors. Previous research configurations such as ASTM E3161-21 relied on an outlet stream gravity draining from a side drain port located above sampling coupons. This limited applications to experimental conditions with a controlled inlet and uncontrolled outlet flow. With the introduction of a small single pole single throw (SPST) reed float switch and a peristaltic pump connected to the outlet drain and a chassis controller, the bioreactor is able to maintain a set level. The modification allows additional variables to be tested, including highly adjustable fill and flush cycles, bioreactor volume, draining and filling control. Once the configuration modifications were implemented through the installation of the new equipment, data was collected to ensure the stability of the level measurements. As the level control switch is a float switch, consideration was taken into account for effects of internal stirring speed, along with effects of inlet and outlet flow rate. Data presented in this study will illustrate the stability and effectiveness of the configuration changes in equipment made to the bioreactor. These configuration changes have demonstrated control method to conduct biofilm mitigation techniques for ECLSS hardware research. The controlled level capabilities allow for a constant drip feed flow rate into the bioreactors, a key aspect of the biofilm mitigation testing.

CDC Bioreactor↗

Experimental Studies on the Effect of Inlet Liquid Subcooling on the Chilldown Characteristics of Stainless Steel Tubes

Understanding transfer line chilldown process under microgravity is important for the efficient transfer of cryogenic propellants in space fuel depots to facilitate future long duration space missions. The present work is part of the ongoing efforts to develop and test a two-phase flow chilldown test section to study the complete chilldown process under sustained microgravity conditions onboard the International Space Station. In this study, ground-based chilldown experiments are carried out on a 60 cm long SS-316 test section with PF-5060 as the working fluid. The complete chilldown curve was obtained including the film, transition and nucleate boiling regimes along with the temperature transition points. The effect of inlet liquid subcooling on the behavior of the chilldown curves are presented. Further, the chilldown and heat flux curves are analyzed to obtain re-wetting/Leidenfrost and onset of nucleate boiling temperature transition points as well as the critical heat flux values. The effect of inlet liquid subcooling on regime-specific heat flux and heat transfer coefficients are also examined.

CFD↗

Acoustic Simulations of Two-stage Fans Behind a Supersonic Inlet

NASA created, validated, and applied a high fidelity simulation toolchain for noise prediction of a fan system for a near-term civilian supersonic aircraft engine. A high fidelity inlet and multistage fan design were acquired as the basis for physics based computational studies. The overall tone noise was computed, which was used to help improve empirical models of fan inlet noise for system analysis purposes. Additional insights were gained during the study of the fan installation details and these are shared in this paper. Both overall amplitudes and variations due to design details should be of interest to engineers tasked with designing quiet fan systems for supersonic commercial aircraft. The outlook for high-fidelity simulations of aft fan noise and installation effects will also be discussed.

fans↗

Acoustic Simulations of Two-stage Fans Behind a Supersonic Inlet

NASA created, validated, and applied a high fidelity simulation toolchain for noise prediction of a fan system for a near-term civilian supersonic aircraft engine. A high fidelity inlet and multistage fan design were acquired as the basis for physics based computational studies. The overall tone noise was computed, which was used to help improve empirical models of fan inlet noise for system analysis purposes. Additional insights were gained during the study of the fan installation details and these are shared in this paper. Both overall amplitudes and variations due to design details should be of interest to engineers tasked with designing quiet fan systems for supersonic commercial aircraft. The outlook for high-fidelity simulations of aft fan noise and installation effects will also be discussed.

fan↗

Concerning the flow about ring-shaped cowlings Part VI : further measurements on inlet devices

The present report presents as a supplement to the fourth report (available as ATI 5045, Air Materiel Command) in the series of investigations concerning the flow about ring-shaped cowlings further wind-tunnel measurements on inlet devices which are to show the influence of the radius of the nose of the cowling on the flow conditions. Moreover, a simple rule for the design of such arrangements, containing a hub in the interior, is suggested.

AIR FLOW - ENGINE COWLINGS↗