Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lattice Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Origin of room temperature ferromagnetic moment in Rh-rich [Rh/Fe] multilayer thin films

B2 ordered FeRh thin films switch from antiferromagnetic (AFM) to ferromagnetic (FM) state on heating above 350 K and switch back on cooling, with a hysteresis. This property makes FeRh a very attractive choice as a write-assist layer material for low temperature heat assisted magnetic recording (HAMR) media. Studies have shown that as we decrease the thickness of the FeRh films, the B2 phase is no longer AFM even below 350 K and there is a thickness dependant FM stabilization of the B2 phase. It was also proved that slightly Rh-richer compositions (>50 at. % Rh) were more preferable to stabilize the AFM phase. The current study focuses on growing highly ordered FeRh films by alternate layer rf sputtering of thin layers of iron and rhodium onto a heated substrate. It has been shown that films with rhodium content beyond 55 at. % contain a disordered bcc FM phase which gives rise to residual moment at room temperature even for thicker films.

36 MATERIALS SCIENCE↗

Size dependent strengthening mechanisms in sputtered Fe/W multilayers

We investigate size dependent strengthening mechanisms in sputtered Fe/W multilayers with individual layer thickness, h, varying from 1 to 200 nm. Microstructure analyses reveal that Fe/W has incoherent bcc/bcc interface when h is greater than 5 nm. When h decreases to 1-2.5 nm, the interface becomes semicoherent, and Fe and W show significant lattice distortions comparing to their bulk counterpart due to interface constraint. The layer thickness dependent drastic variations in x-ray diffraction profiles are simulated well by using an analytical model. Film hardness increases with decreasing h, and approaches a maximum value of 12.5 GPa when h is 1 nm. The layer thickness dependent film hardnesses are compared with analytical models. Koehler's image force plays a major role in determining the maximum strength of composites at smaller h.

36 MATERIALS SCIENCE↗

Preparation and Properties of FeCo Nanoparticles

Fe-Co nanoparticles were prepared from the binary Fe-Co oxalate. The formation of FeCo metallic phase begun at 290 deg. C as determined from the X-ray diffraction patterns recorded during heating of the oxalate sample in hydrogen atmosphere. The reduction finished at 500 deg. C by formation of bcc FeCo phase with a mean particle size of about 50 nm. Analysis of the Moessbauer spectra shows that the ferromagnetic FeCo phase is represented by two sextets corresponding to interiors and surfaces of the nanoparticles. In addition, a weak paramagnetic component, represented by the doublet, was observed which was ascribed to fine particles in a superparamagnetic state. TEM images have shown conglomerates of particles with the composition of about 50 at. % Fe and 50 at. % Co.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Solid State Reactions in the Mo/O--Fe System under Mechanical Alloying

Two types of solid state reactions that occur during mechanical alloying of Mo/O --20 at. % Fe system with various oxygen concentrations were studied by Moessbauer spectroscopy and X-ray diffraction. The first type of solid state reaction, Mo/O+Fe{yields}bcc Mo(O)-Fe, was observed for Mo samples with 8 at. % of oxygen. The second type of solid state reaction proceeds as Mo/O+Fe{yields}bcc Mo(O)-Fe+hcp Mo(O)-Fe{yields}bcc Mo(O)-Fe+Am Mo(O)-Fe for Mo samples with 14 at. % of oxygen and 1.6 at. % of MoO{sub 3} phase. The assumption about correlation between the second component dissolution rate and mixture components yield point ratio is confirmed.

36 MATERIALS SCIENCE↗

Moessbauer and SANS Studies of Anti-Invar Fe-Ni-C Alloy under Magnetic Field

Anti-Invar effect in the f.c.c.-Fe-25.3%Ni-C alloy was revealed, i.e., enhanced thermal expansion coefficient (TEC)({approx}20x10{sup -6} K{sup -1}) which was accompanied by almost temperature-insensitive behavior in a temperature range of 122-525 K that was considerably expanded to the low temperature range due to alloying with carbon. The Moessbauer and small-angle neutron scattering (SANS) experiments with the varying temperature and in an external magnetic field of 1.5-5 T have revealed an existence of inhomogeneous magnetic order in anti-Invar alloy below and above the magnetic transition point. The anti-Invar behavior correlates with the thermally induced change in the magnetic order and interspin interaction.

36 MATERIALS SCIENCE↗

Optical spectroscopy of cubic GaN in nanowires

We show that highly homogeneous cubic GaN can be grown by plasma-assisted molecular beam epitaxy on wurtzite GaN nanowires. The line width of the donor bound exciton is below 3 meV and can reach 1.6 meV in the best parts of the studied sample. This allows to perform a detailed spectroscopy of cubic GaN, and, in particular, to determine the precise spectral positions of the donor bound exciton, the fundamental free exciton and the split-off exciton in a photoluminescence experiment.

36 MATERIALS SCIENCE↗

Room-temperature infrared photoluminescence from sputter-deposited InN films

Wurtzite InN films are deposited on Si(100) and glass substrates by reactive rf-magnetron sputtering at a substrate temperature of 300 deg. C. The InN films have high electron concentrations of n{approx}4x10{sup 20} cm{sup -3} at 300 K. The optical band-gap energy is determined to be {approx}1.4 eV at 300 K. This value is considerably smaller than the previously reported value of {approx}2 eV in sputter-deposited InN films. Strong infrared photoluminescence (PL) with a peak at {approx}1.3 eV is also observed at room temperature. Thermal annealing in dry N{sub 2} atmosphere at 600 deg. C changes the deposited film from wurtzite InN to a cubic In{sub 2}O{sub 3} that still exhibits PL emission but in the visible spectral region ({approx}2 eV).

36 MATERIALS SCIENCE↗

Nonstoichiometric BiFe{sub 0.9}Ti{sub 0.05}O{sub 3} multiferroic ceramics with ultrahigh electrical resistivity

BiFeO{sub 3}, BiFe{sub 0.9}Ti{sub 0.1}O{sub 3}, and BiFe{sub 0.9}Ti{sub 0.05}O{sub 3} ceramics of relatively high perovskite phase content were prepared for a comparison study. While both BiFe{sub 0.9}Ti{sub 0.1}O{sub 3} and BiFe{sub 0.9}Ti{sub 0.05}O{sub 3} exhibit similarly improved weak ferromagnetism over BiFeO{sub 3}, there exists a major difference in the x-ray diffraction patterns of BiFe{sub 0.9}Ti{sub 0.1}O{sub 3} and BiFe{sub 0.9}Ti{sub 0.05}O{sub 3}, and the leakage current of BiFe{sub 0.9}Ti{sub 0.05}O{sub 3} is decreased by five orders of magnitude from that of BiFe{sub 0.9}Ti{sub 0.1}O{sub 3}. With an ultrahigh electrical resistivity, over 1x10{sup 14} {Omega} cm, BiFe{sub 0.9}Ti{sub 0.05}O{sub 3} ceramic displays an especially low dielectric loss, 0.015 at 100 Hz, a remanent polarization P{sub r} of 0.23 {mu}C/cm{sup 2} and a remanent magnetization M{sub r} of 0.13 emu/g at room temperature. It is proposed that the Fe-deficiency in BiFe{sub 0.9}Ti{sub 0.05}O{sub 3} decreases the amount of Fe{sup 2+} and leads to the ultrahigh electrical resistivity. Nonstoichiometric compositions should receive more attention for developing high quality BiFeO{sub 3} multiferroic materials.

36 MATERIALS SCIENCE↗

Impact of Morphological Features on the Dielectric Breakdown at SiO{sub 2}/3C-SiC Interfaces

Thin SiO{sub 2} layers were thermally grown onto cubic silicon carbide (3C-SiC) heteroepitaxial layers of different surface roughness and with different types of near-surface epitaxial defects. Localized dielectric breakdown (BD) was studied by electrically stressing the system using Conductive Atomic Force Microscopy (C-AFM), which constitutes a means to directly and simultaneously observe localized dielectric failure as a function of stress time and surface morphology with nanoscale lateral resolution. The BD kinetics was evaluated by fitting the experimental failure ratios as a function of stress time to the failure probability described by Weibull statistics, in turn allowing to distinguish between defect-induced (extrinsic) and intrinsic dielectric BD events. The results give useful information about how morphological features at the 3C-SiC surface influence the BD generation in thermally grown oxides on this polytype.

36 MATERIALS SCIENCE↗

Electrical transport properties of the Si-doped cubic boron nitride thin films prepared by in situ cosputtering

Si-doped cubic boron nitride (c-BN) films with various Si concentrations were achieved by in situ cosputtering during ion beam assisted deposition. Effects of the Si concentration and rapid thermal annealing (RTA) conditions on the electrical transport properties of Si-doped c-BN thin films were investigated systematically. The results suggest that the optimum RTA condition is at the temperature of 1000 deg. C for 3 min. The resistance of Si-doped c-BN films gradually decreases as the Si concentration increases, indicating an electrical doping effect of the Si impurity. The temperature dependent electrical conductivity of the Si-doped c-BN films suggests that different conduction mechanisms are dominant over the different temperature ranges. Based on the Davis-Mott model, we propose that the extended-state conduction, band tail-state conduction and short-range hopping conduction are responsible for the respective temperature ranges. In addition, the reduction in activation energy of Si impurities is observed as the Si concentration increases.

36 MATERIALS SCIENCE↗

The A1 to L1{sub 0} transformation in FePt films with ternary alloying additions of Mg, V, Mn, and B

The impact of ternary additions of Mg, V, Mn, and B on the A1 [face centered cubic (fcc)] to L1{sub 0} phase transformation has been studied. The films were cosputter deposited from elemental targets at room temperature and annealed after deposition. The films had Mg additions in the range {approx}0-2.6 at.%, V additions in the range 0.7-12.2 at.%, Mn additions in the range 2.2-16.3 at.%, and B additions in the range 1.2-12.9 at.%. For all four ternary alloy systems, annealing resulted in the formation of no other phases than the L1{sub 0} phase. Ternary additions of <1.8 at.% Mg, <5.8 at.% V, <6.0 at.% Mn, and <4.8 at.% B had little or no impact on the kinetic ordering temperature (KOT). The behavior of the activation energy for the transformation mirrored that for the KOT, except for Mg additions, which showed no measurable impact for the compositions studied. The transformation enthalpies for the ternary alloys were similar to those for binary FePt films. Only four of the films (with additions of 2.6 at.% Mg, 2.2 at.% and 6.0 at.% Mn, and 4.8 at.% B) for which the Curie transition was observed had lower T{sub C} than the binary FePt films with the same Pt content.

36 MATERIALS SCIENCE↗

Perpendicular magnetic anisotropy and spin reorientation transition in L1{sub 0} FePt films

We investigated the thickness and composition dependence of perpendicular magnetic anisotropy (PMA) in L1{sub 0} Fe{sub 1-x}Pt{sub x} (x = 0.4, 0.5, and 0.55) films. The FePt films with different thicknesses of 35 and 70 A were grown at the substrate temperature T{sub s} = 300 deg. C by molecular beam epitaxy coevaporation technique. A (001)-oriented epitaxial L1{sub 0} FePt film was grown on the thin (001)-oriented fcc Pt layer, while a poorly crystallized FePt film was formed on the (111)-textured Pt layer. Our results showed that, at a fixed thickness of 70 A, the PMA of FePt alloy films is enhanced as Pt content increases from 40% to 55%.

36 MATERIALS SCIENCE↗

Phase change behavior in titanium-doped Ge{sub 2}Sb{sub 2}Te{sub 5} films

The titanium-doped Ge{sub 2}Sb{sub 2}Te{sub 5} films were deposited on Si(100) substrates by comagnetron sputtering method. The titanium concentrations in those films were determined by x-ray photoelectron spectroscopy. The influence of Ti doping upon phase change characteristics of the samples has been investigated by x-ray diffraction and a temperature-regulable UVISEL typed spectroscopic ellipsometry. With the augmentation of Ti doping concentration, the crystalline temperatures of the films went up while annealing, and the face-centered-cubic phase of them had high thermal stability because of the bond making between Ti and Te elements partly.

36 MATERIALS SCIENCE↗

Room Temperature Ferromagnetism in Cu Doped ZnO Thin Films

We report on the growth of Cu doped ZnO thin films for different Cu concentration from 0.1%, to10% by RF magnetron sputtering. The X-ray diffraction study has shown single phase wurtzite type ZnO thin films with no evidence of copper/copper oxide or any other secondary phases. Room temperature ferromagnetism was observed in RF sputtered Cu doped ZnO films with magnetic moment per Cu atom first increasing and then decreasing with an increasing Cu content. Decrease of band gap with Cu doping, indicating strong p-d mixing of O and Cu is clear by the absorption spectroscopy study. The surface morphology by AFM of pure and Cu doped ZnO thin films show average grain size of 110nm and RMS surface roughness of 2.15 nm.

36 MATERIALS SCIENCE↗

Electron Screening in Metals

Electron screening enhances cross sections for nuclear reactions at low energies. We have studied the {sup 1}H({sup 7}Li,{alpha}){sup 4}He reaction in inverse kinematics and observed large electron screening only when the metallic targets were under tensile stress. Hydrogen was loaded into Pd and PdAg alloy foils from gas phase and concentrations reached about 0.6 protons per metallic atom. Mechanical pressure creates stress induced states in the metal. Without pressure hydrogen occupies octahedral interstitial positions in the fcc Pd lattice. Under stress some protons move to dislocated octahedral (dis-O) sites in the lattice. We believe that the magnitude of screening in various metals depends on the electron density on dis-O sites in case of fcc lattices or dislocated tetrahedral sites in bcc metals. We are currently trying to confirm the above by determining the electron density at the sites occupied by protons via the measurement of proton Knight's shift with {sup 1}H nuclear magnetic resonance technique.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

High Cubic-Phase Purity InN on MgO (001) Using Cubic-Phase GaN as a Buffer Layer

High cubic-phase purity InN films were grown on MgO (001) substrates by molecular beam epitaxy with a cubic-phase GaN buffer layer. The cubic phase purity of the InN grown layers has been analyzed by high resolution X-ray diffraction, {mu}-Raman scattering and transmission electron microscopy. It is evidenced that the hexagonal-phase content in the InN overlayer much depends on hexagonal-phase content in the cubic-phase GaN buffer layer and increases with increasing the hexagonal-phase GaN content. From Raman scattering measurements, in addition, the InN layer with lowest hexagonal component (6%), only Raman characteristics of cubic TO{sub InN} and LO{sub InN} modes were observed, indicating a formation of a small amount of stacking faults, which does not affect on vibrational property.

36 MATERIALS SCIENCE↗

Single phase synthesis and room temperature neutron diffraction studies on multiferroic PbFe{sub 0.5}Nb{sub 0.5}O{sub 3}

The lead-iron-niobate, (PbFe{sub 0.5}Nb{sub 0.5}O{sub 3} or PFN) was synthesized by low temperature sintering Single Step / Solid State Reaction Method. The 700 Degree-Sign C/2 hrs. calcined powder was sintered at 1050 Degree-Sign C/1 hr. The sintered pellets were characterized through X-Ray Diffraction and Neutron Diffraction at room temperature. It is found from the XRD pattern that the materials is in single phase with no traces of pyrochlore phase. It was also confirmed from the neutron diffraction pattern, the structure of PFN to be monoclinic, space group Cm. Structural studies has been carried out by refining the obtained neutron diffraction data by Rietveld refinement method using Fullprof program. The neutron diffraction pattern at 300 K (room temperature) was selected to refine the structure. The lattice parameters obtained are; a = 5.6709 A, b = 5.6732 A, c = 4.0136 A, and {alpha}= 90, {beta}= 89.881, {gamma}= 90. The P-E measurements showed hysteretic behavior with high remnant polarization.

36 MATERIALS SCIENCE↗

Band structure properties of (BGa)P semiconductors for lattice matched integration on (001) silicon

We report the band structure properties of (BGa)P layers grown on silicon substrate using metal-organic vapour-phase epitaxy. Using surface photo-voltage spectroscopy we find that both the direct and indirect band gaps of (BGa)P alloys (strained and unstrained) decrease with Boron content. Our experimental results suggest that the band gap of (BGa)P layers up to 6% Boron is large and suitable to be used as cladding and contact layers in GaP-based quantum well heterostructures on silicon substrates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗