Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Phase Change Material for Temperature Control of Loop Heat Pipe Compensation Chamber

The compensation chamber (CC) of a loop heat pipe (LHP) requires a stable temperature. In the current technology, the CC is commonly cold biased by exposing it to deep space, and active heater control is used to maintain its temperature stable. Heater power required for a typical LHP with a 300 W heat transport capacity is as much as 25 W. If multiple LHPs are used, heater power requirement could be a bigger issue. Also heater controller or temperature sensor failure could lead to a LHP or mission failure. This paper presents an innovative concept of using phase change material (PCM) for temperature control of LHP CC. Some of the electronics and/or detector assembly waste heat is stored in the PCM and transferred to the LHP CC by constant conductance heat pipes (CCHPs). Phase change of the PCM occurs at a constant temperature and maintains the LHP CC temperature stable. It eliminates heater power and active heater control for the CC. It also increases the reliability of LHP.

Choi, Michael K.↗

Motor power factor controller with a reduced voltage starter

A power factor type motor controller is disclosed in which the conventional power factor constant voltage command signal is replaced during a starting interval with a graduated control voltage. This continuation-impart of a pending patent application (Serial No. 199, 765: Three Phase Factor Controller) provides a means for modifying the operation of the system for a motor start-up interval of 5 to 30 second. Using a ramp generators, an initial ramp-like signal replaces a constant power factor signal supplied by a potentiometer. The ramp-like signal is applied to a 15 terminal where it is summed with an operating power factor signal from phase detectors in order to obtain a control signal for ultimately controlling SCR devices. The SCR devices are turned on at an advancing rate with time responsive to the combination signal described rather than simply a function of a ramp-like signal alone.

Nola, F. J.↗

Microstructure and coercivity in alnico 9

Magnetic property enhancement of alnico, a rare-earth free permanent magnet, is highly dependent on both the initial microstructure and the evolution of the spinodal decomposition (SD) inside each grain during the heat treatment process. The size, shape and distribution of the magnetic FeCo-rich (α 1 ) phase embedded in continuous non-magnetic AlNi-rich (α 2 ) phase as well as a minor Cu-enriched phase residing in between are shown to be crucial in controlling coercivity. Phase and magnetic domain morphology in a commercial alnico 9 alloy was studied using a combination of structural characterization techniques, including scanning electron microscopy, electron backscatter diffraction, aberration-corrected scanning transmission electron microscopy and Lorentz microscopy. Our results showed that casting created structural nonuniformity and defects, such as porosity, TiS 2 precipitates and grain misorientation, are heterogeneously distributed, with the center section having the best crystallographic orientation and minimal defects. The optimal spinodal is a “mosaic structure”, composed of rod-shape α1 phase with {110} or {100} planar faceting and diameter of ~30–45nm. There is also a Cu-enriched phase residing at the corners of two < 110 > facets of the α1 phase. Furthermore, it was observed that grain boundary phase reverse magnetization direction at lower external magnetic field compared to the SD region inside the grain. Improving grain orientation uniformity, reducing detrimental grain boundary phase volume fraction, and the branching of the α 1 rods, as well as their diameter, are promising routes to improve energy product of alnico.

36 MATERIALS SCIENCE↗

Effect of heat treatment time on microstructure and electrical conductivity in LATP glass ceramics

Glass-ceramic is prepared by heat treatment of melt quenched 14Li{sub 2}O−9Al{sub 2}O{sub 3}−38TiO{sub 2}−39P{sub 2}O{sub 5} glass in the vicinity of crystallization temperature. Growth of ceramic phase is controlled by tuning heat treatment time at fixed temperature. Ceramic phase was identified to be LiTi{sub 2}(PO{sub 4}){sub 3} from X Ray Diffraction analysis. Microstructural evolution of this phase with hold time was observed under high resolution Scanning Electron Microscope. DC conductivity is observed to increase by 4-5 orders of magnitude in this glass-ceramic compared to parent glass. However, formation of pores and cracks with very large heat treatment time seem to hinder further increase of conductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dynamic non-reciprocal meta-surfaces with arbitrary phase reconfigurability based on photonic transition in meta-atoms

We introduce a distinct class of dynamic non-reciprocal meta-surfaces with arbitrary phase-reconfigurability. This meta-surface consists of an array of meta-atoms, each of which is subject to temporal refractive index modulation, which induces photonic transitions between the states of the meta-atom. We show that arbitrary phase profile for the outgoing wave can be achieved by controlling the phase of the modulation at each meta-atom. Moreover, such dynamic meta-surfaces exhibit non-reciprocal response without the need for magneto-optical effects. The use of photonic transition significantly enhances the tunability and the possible functionalities of meta-surfaces.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

MP1 Intermediate Characterization Report Summary

Great effort worldwide has been invested in replacing high enriched uranium (HEU) fuel with low enriched uranium (LEU) fuel in nuclear plants. This effort aims in safeguarding nuclear material and promoting the proliferation resistance of current reactors. The United States Department of Energy (DOE), National Nuclear Security Administration's (NNSA) Materials Management and Minimization Reactor Conversion program is actively working to convert civilian research and test reactors from the use of HEU to LEU fuel. To date, DOE NNSA has converted or verified the shutdown of various domestic reactors and also reactors worldwide. The task to develop and test a new LEU fuel while maintaining current performances has been assigned to the High-Performance Research Reactor (USHPRR) program. U alloyed with Mo achieves the goal of high uranium density necessary for the conversion of the high performance research reactors, and has also demonstrated good performance in pile [1]. The alloying process of U with Mo stabilizes the body-centered cubic (bcc) gamma phase (?-U) at room temperature. Without this alloying property enhancement, this phase is only stable at temperatures only above 770 °C. Retaining this isotropic gamma phase within the U-Mo alloy provides swelling and oxidation resistance and desired mechanical properties [2]. Generally 10% w. has been considered sufficient to achieve stabilization. However, local phenomena within the alloy can affect the local Mo content and lead to gamma phase decomposition. Because of this, it has been suggested that controlling gamma phase decomposition is most critical during processing [2-3]. The work detailed in this document is part of the HPPR program and focuses on the characterization of fresh fuel (a.k.a. as fabricated, before reactor testing) in collaboration with other laboratories including PNNL (Pacific Northwest National Laboratory), LANL (Los Alamos National Laboratory) and BWXT (Babcock and Wilcox Technologies). This testing is part of a 4 way validation for which similar samples from master plates were taken and distributed to each laboratory to independently analyze utilizing a standardized set of measurement and analysis procedures. When complete this work will supply a “toolbox” of information for alloying and fabrication parameters with its direct effects on microstructure quantified. Various parameters have been analyzed in this characterization effort (including grain size, quality of the coating layer, composition of the samples, carbide content etc.), based on the direction of the working group in ref.[4]. The final aim of this work is to increase the understanding of the impact of processing conditions on the final fuel microstructure, using fabrication processes that meet “commercial viability” requirements [4]. The strength of this campaign rests on the extent of the samples studied and the variation of the manufacture parameters which will permit to achieve the required understanding. Thus permitting to use these experiments to down-select test samples used to evaluate irradiation performance [4] to be tested in various locations of the Idaho National Laboratory (INL) Advanced Test Reactor (ATR).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A navigation and control system for an autonomous rescue vehicle in the space station environment

A navigation and control system was designed and implemented for an orbital autonomous rescue vehicle envisioned to retrieve astronauts or equipment in the case that they become disengaged from the space station. The rescue vehicle, termed the Extra-Vehicular Activity Retriever (EVAR), has an on-board inertial measurement unit ahd GPS receivers for self state estimation, a laser range imager (LRI) and cameras for object state estimation, and a data link for reception of space station state information. The states of the retriever and objects (obstacles and the target object) are estimated by inertial state propagation which is corrected via measurements from the GPS, the LRI system, or the camera system. Kalman filters are utilized to perform sensor fusion and estimate the state propagation errors. Control actuation is performed by a Manned Maneuvering Unit (MMU). Phase plane control techniques are used to control the rotational and translational state of the retriever. The translational controller provides station-keeping or motion along either Clohessy-Wiltshire trajectories or straight line trajectories in the LVLH frame of any sufficiently observed object or of the space station. The software was used to successfully control a prototype EVAR on an air bearing floor facility, and a simulated EVAR operating in a simulated orbital environment. The design of the navigation system and the control system are presented. Also discussed are the hardware systems and the overall software architecture.

Merkel, Lawrence↗

Momentum Transfer in a Spinning Fuel Tank Filled with Xenon

Transient spin-up and spin-down flows inside of spacecraft fuel tanks need to be analyzed in order to properly design spacecraft control systems. Knowledge of the characteristics of angular momentum transfer to and from the fuel is used to size the de-spin mechanism that places the spacecraft in a controllable in-orbit state. In previous studies, several analytical models of the spin-up process were developed. However, none have accurately predicted all of the flow dynamics. Several studies have also been conducted using Navier-Stokes based methods. These approaches have been much more successful at simulating the dynamic processes in a cylindrical container, but have not addressed the issue of momentum transfer. In the current study, the spin-up and spin-down of a fuel tank filled with gaseous xenon has been investigated using a three-dimensional unsteady Navier-Stokes code. Primary interests have been concentrated on the spin-up/spin-down time constants and the initial torque imparted on the system. Additional focus was given to the relationship between the dominant flow dynamics and the trends in momentum transfer. Through the simulation of both a cylindrical and a spherical tank, it was revealed that the transfer of angular momentum is nonlinear at early times and tends toward a linear pattern at later times. Further investigation suggests that the nonlinear spin up is controlled by the turbulent transport of momentum, while the linear phase is controlled by a Coriolis driven (Ekman) flow along the outer wall. These results indicate that the spinup and spin-down processes occur more quickly in tanks with curved surfaces than those with defined top, bottom, and side walls. The results also provide insights for the design of spacecraft de-spin mechanisms.

Peugeot, John W.↗

Single bus star connected reluctance drive and method

A system and methods for operating a switched reluctance machine includes a controller, an inverter connected to the controller and to the switched reluctance machine, a hysteresis control connected to the controller and to the inverter, a set of sensors connected to the switched reluctance machine and to the controller, the switched reluctance machine further including a set of phases the controller further comprising a processor and a memory connected to the processor, wherein the processor programmed to execute a control process and a generation process.

33 ADVANCED PROPULSION SYSTEMS↗

Multiple beam phased array for Space Station Control Zone Communications

The Space Station Communications Control Zone is a disk shaped region 40 nautical miles in diameter and 10 nautical miles thick centered about the Space Station. It is estimated that 6 simultaneous Multiple Access (MA) channels will be required to satisfy the projected communications needs within this zone. These channels will be used to communicate with MA users located anywhere within the Control Zone. This paper details the tradeoffs and design implementation of a multiple beam integrated phased array to provide antenna coverage of the Control Zone. The array is a compact, modular assembly using Gallium Arsenide circuits, microstrip elements, and advanced packaging techniques. This results in a small, reliable antenna system capable of meeting the projected Space Station requirements and flexible enough to grow and evolve as the Space Station communications needs develop.

Halsema, P. B.↗

Easy parallel screening of reagent stability, quality control, and metrology in solid phase peptide synthesis (SPPS) and peptide couplings for microarrays

Evaluating the stability of coupling reagents, quality control (QC), and surface functionalization metrology are all critical to the production of high quality peptide microarrays. We describe a broadly applicable screening technique for evaluating the fidelity of solid phase peptide synthesis (SPPS), the stability of activation/coupling reagents, and a microarray surface metrology tool. This technique was used to assess the stability of the activation reagent 1-{[1-(Cyano-2-ethoxy-2-oxo-ethylidenaminooxy)dimethylamino-morpholinomethylene]}methaneaminiumHexafluorophosphate (COMU) (Sigma-Aldrich, St. Louis, MO, USA) by SPPS of Leu-Enkephalin (YGGFL) or the coupling of commercially synthesized YGGFL peptides to (3-aminopropyl)triethyoxysilane-modified glass surfaces. Coupling efficiency was quantitated by fluorescence signaling based on immunoreactivity of the YGGFL motif. It was concluded that COMU solutions should be prepared fresh and used within 5 h when stored at ~23 °C and not beyond 24 h if stored refrigerated, both in closed containers. Caveats to gauging COMU stability by absorption spectroscopy are discussed. Commercial YGGFL peptides needed independent QC, due to immunoreactivity variations for the same sequence synthesized by different vendors. This technique is useful in evaluating the stability of other activation/coupling reagents besides COMU and as a metrology tool for SPPS and peptide microarrays.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Facile microwave-assisted aqueous synthesis of CdS nanocrystals with their photocatalytic activities under visible lighting

Graphical abstract: - Highlights: • Three kinds of CdS nanostructures have been controllably synthesized. • Ethanediamine acts as a phase and morphology controlling reagent. • Three CdS nanostructures display high visible light photocatalytic activities. • Cubic CdS-3 shows superior photocatalytic activity to the other hexagonal CdS. • The growth processes for fabrication of CdS nanocrystals are also discussed. - Abstract: Three kinds of CdS nanostructures, that is, hexagonal nanospheres (CdS-1), hierarchical caterpillar-fungus-like hexagonal nanorods (CdS-2) and hierarchical cubic microspheres (CdS-3), were controllably synthesized by a facile and one-pot microwave-assisted aqueous chemical method using ethanediamine as a phase and morphology controlling reagent. The as-prepared products were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectra (DRS) and photoluminescence (PL) spectra. The results show that CdS-1 is mainly composed of monodispersed hexagonal nanospheres with average diameters of about 100 nm; hexagonal CdS-2 has lengths in the range of 600–800 nm and diameters of 40–60 nm, assembled by nanoparticles about 20 nm in diameter; and CdS-3 is pure cubic microspheres with diameters in the range of 0.8–1.3 μm, aggregated by tiny nanograins with size of 5.8 nm. The band gap energies of CdS products were calculated to be 2.30, 2.31 and 2.24 eV observed from UV–vis DRS for CdS-1, CdS-2 and CdS-3, respectively. PL spectra of CdS samples showed that sphalerite CdS-3 possesses a very weak fluorescence, while wurtzite CdS-2 has a strongest green near-band edge emission (NBE) at 550 nm. The visible light photodegradation of methylene blue and rhodamine B in the presence of CdS photocatalysts illustrates that all of them display high photocatalytic activities. Significantly, the cubic CdS-3 exhibits more excellent photocatalytic behavior in degradation of organic dyes than the other hexagonal CdS, which is closely related to the phase and morphology structure of cubic CdS.

36 MATERIALS SCIENCE↗

Directing the phase behavior of polyelectrolyte complexes using chiral patterned peptides

Polyelectrolyte complexes (PECs) have a broad range of promising applications as soft materials due to their self-assembly and diversity of structure and chemical composition. Peptide polymer PECs are highly biocompatible and biodegradable, making them particularly useful for encapsulation of food additives and flavors, micellar drug delivery, medical and underwater adhesives, fetal membrane patches, and scaffolds for cell growth in tissue engineering. While parameters affecting PEC formation and stability in regards to charge effects are well researched, little is known about the effects of van der Waals interactions, hydrogen bonding, and secondary structure in these materials. Peptide chirality provides a unique opportunity to manipulate PEC phase to modulate the amount of solid-like (precipitate) or liquid-like (coacervate) character by influencing hydrogen bonding interactions among peptide chains. In previous work, we showed that chiral peptides form solid complexes, while complexes with even one racemic peptide were fluid. This raised the interesting question of how long a homochiral sequence must be to result in solid phase formation. In this work, we designed chiral patterned peptides of polyglutamic acid and polylysine ranging from 50 to 90% L-chiral residues with increasing numbers of sequential L-chiral residues before a chirality change. These polymers were mixed together to form PECs. We observed that 8 or more sequential L-chiral residues are necessary to achieve both the appearance of a precipitate phase and sustained beta-sheets in the complex, as determined by optical imaging and FTIR Spectroscopy. Less homochiral content results in formation of a coacervate phase. Thus, we show that chiral sequence can be used to control the phase transition of PECs. Understanding how to manipulate PEC phase using chiral sequence as presented here may enable tuning of the material properties to achieve the desired mechanical strength for coatings and polymer brushes, or the most effective molecular release kinetics for drug delivery applications, for example.

Pacalin, Naomi M.↗

Coherent lightwave communications; Proceedings of the Meeting, Boston, MA, Sept. 7, 8, 1989

Various papers on coherent lightwave communications are presented. Individual topics addressed include: overview of coherent light wave communications, frequency stabilization techniques for coherent lightwave systems, characterization of laser diode intensity noise at microwave frequencies with high sensitivity, FP and DFB semiconductor lasers with arbitrary external optical feedback, birefringence-controlled phase-shifter, polarization diversity and scrambling techniques for coherent systems, polarization control scheme for coherent optical systems, simulation of IF filtering effects on the performance of coherent optical receivers. Also discussed are: performance of optical DPSK receivers in the presence of optical channel noise, optical heterodyne communications with polarization modulation, coherent fiber optical subcarrier multiplexed system, engineered rack-mounted coherent transmission system, technology aspects of a coherent optical MAN, broadband exchange by coherent multicarrier switching, generalized temporal CDMA for optical communications. Overviews are given of recent progress at individual companies.

Sunak, Harish R. D.↗

Safety-Related Instrumentation and Control Pilot Upgrade: Conceptual - Detailed Design Phase Report and Lessons Learned

Historically, regulatory barriers have precluded nuclear plant safety-related (SR) Instrumentation and Control (I&C) system modernizations. These barriers have been largely addressed by industry and United States Nuclear Regulatory Commission (NRC) efforts, including development of the License Amendment Request (LAR) Alternate Review (AR) process for digital I&C upgrades. The U.S. Department of Energy (DOE) and the Idaho National Laboratory (INL) are supporting a SR I&C pilot upgrade at the Limerick Generating Station (LGS) to demonstrate this process and capturing associated lessons learned for the benefit of industry. In 2021, a paper summarizing lessons learned as captured in INL/EXT-20-59809, Safety Related Instrumentation & Control Pilot Upgrade Initial Scoping Phase Implementation Report and Lessons Learned was presented at the 12th NPIC & HMIT conference. It is recommended that readers of this paper review reference 1 or the associated Nuclear Journal paper for context. This paper summarizes activities performed and lessons learned for the conceptual design phase and portions of the detailed design phase as captured in INL/RPT-23-XXXX, “Safety-Related Instrumentation and Control Pilot Upgrade: Conceptual - Detailed Design Phase Report and Lessons Learned.” The portions of the effort covered by reference 2 include conceptual design phase activities from December 2020, through completion in November 2021, and detailed design activities through September 2022. These efforts and associated detailed documentation in reference 3 are intended to support similar industry upgrades as a foundation stone for a Digital Transformation that will improve plant safety, reliability, and operational performance while lowering plant total cost of ownership.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Frequency stabilization in nonlinear MEMS and NEMS oscillators

An illustrative system includes an amplifier operably connected to a phase shifter. The amplifier is configured to amplify a voltage from an oscillator. The phase shifter is operably connected to a driving amplitude control, wherein the phase shifter is configured to phase shift the amplified voltage and is configured to set an amplitude of the phase shifted voltage. The oscillator is operably connected to the driving amplitude control. The phase shifted voltage drives the oscillator. The oscillator is at an internal resonance condition, based at least on the amplitude of the phase shifted voltage, that stabilizes frequency oscillations in the oscillator.

42 ENGINEERING↗