Search NASA⌕ Search

SEARCH · Search NASA

Results for “REACTIVITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Cracking vs. surface reactivity in high-nickel cathodes for lithium-ion batteries

High-nickel layered oxide cathodes LiNi x Mn y Co z O 2 (NMC) experience microcracks during cycling. This can expose fresh cathode surfaces for parasitic reactions and isolate active cathode material from the conductive electrode matrix, resulting in impedance increase and capacity fade. The commonly held belief attributes microcracks to anisotropic lattice volume changes of primary particles during cycling. Nevertheless, recent reports suggest that certain electrolytes might reduce microcracks in NMC cathodes during deep cycling. This raises a crucial question on the origin of microcracks: do microcracks exacerbate surface stability, or does poor surface stability contribute to microcrack formation? This perspective aims to provide context and expound this “chicken or egg” dilemma. We contend that the consequence of surface reactivity on the cycle life of high-Ni cathodes is more pronounced than that of particle cracking. Here, we hypothesize that particle cracking is more of a symptom of severe surface reactivity rather than a cause of capacity fade.

25 ENERGY STORAGE↗

The effects of zinc bath temperature on the coating growth behavior of reactive steel

The purpose of this work is to identify the influence of zinc bath temperature on the morphology and the thickness of reactive steel (Fe-0.1 wt.%Si alloy) coatings. The Fe-0.1 wt.%Si samples were galvanized for 3 min at temperatures in the range of 450-530 deg. C in steps of 10 deg. C. The coatings were characterized by using scanning electron microscopy/energy dispersive X-rays analysis. It was found that the coating thickness reaches the maximum at 470 deg. C and the minimum at 500 deg. C, respectively. When the reactive steel is galvanized at temperatures in the range of 450-490 deg. C, the coatings have a loose {zeta} layer on the top of a compact {delta} layer. With the increase of the galvanizing temperature, the {zeta} layer becomes looser. When the temperature is at 500 deg. C, the {zeta} phase disappears. With the increase of temperature, the coatings change to be a diffuse-{Delta} layer ({delta}+ liquid zinc).

36 MATERIALS SCIENCE↗

Microstructural development of a C/C-ZrC-Cu composite prepared by reactive melt infiltration with Zr/Cu powder mixture

Highlights: • The composite was prepared by reactive melt infiltration with Zr/Cu powder mixture. • Some ZrC particles coalesced into a continuous layer around the pyrolytic carbon. • Nano-sized inclusions of Cu–ZrC were formed inside some ZrC particles. • Cu–rich phase gathered at the interface between the ZrC layer and pyrolytic carbon. - Abstract: Zirconium carbide (ZrC) was introduced into porous carbon/carbon(C/C) preforms by reactive melt infiltration (RMI) using Zr/Cu powder mixture as the infiltrator. Characterization results revealed that ZrC particles were present in the infiltration matrix in two forms, some of which coalesced into a continuous layer around the pyrolytic carbon (PyC) while the others were dispersed within Cu phase which was distributed throughout the matrix. Nano-sized inclusions of Cu-ZrC were detected inside some ZrC particles. Furthermore, Cu-rich phase was observed at the interface between the continuous ZrC layer and PyC. The formation of Cu-ZrC mixture and Cu-rich phase was attributed to the trapping mechanism that some Zr-Cu-based liquid remained during the coalescence of ZrC particles or the formation of the continuous ZrC layer.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of intragranular W-Cu/TiC-ZrC composite prepared by reactive melt infiltration at 1300 °C

Highlights: • W-Cu/TiC-ZrC composites with nano W dispersoids were prepared by reactive melt infiltration. • The nano-sized dispersoids were analyzed by TEM in detail. • The intragranular nano W dispersoids and ribbon like precipitates have toughening effects. - Abstract: Newly intragranular W-Cu/TiC-ZrC composites with nano W dispersoids in TiC matrix have been prepared by reactive melt infiltration at 1300 °C for 1 h in vacuum using molten Zr-Cu binary alloys and a (Ti{sub 0.75},W{sub 0.25})C solid solution powder as raw materials. The as-synthesized composites consist of major phases of W, Cu, TiC and ZrC. With the decrease of Zr content from 66 to 21 at.% in the Zr-Cu infiltrator, the reaction formed W phase in the composite has changed from micron-sized intergranular grains to nano-sized rounded inclusions in TiC{sub y} grains. The crystallographic orientation relationship at W and TiC interfaces are detected as:(0 1 1-bar ){sub W}//(1 1 1-bar ){sub TiC}&[0 1 1]{sub W}//[0 1 1]{sub TiC} and (4 1 1){sub W}//(4 2 4){sub TiC}&[0 1 1-bar ]{sub W}//[4 2-bar 3-bar ]{sub TiC}. Nano-sized lamellar structure with both W and Cu rich is detected to have super-lattice structure based on the TiC lattice. The elastic modulus, flexural strength, fracture toughness of the intragranular W-Cu/TiC-ZrC composite infiltrated with Zr{sub 14}Cu{sub 51} melt are 207.5 GPa, 457 MPa and 10.21 MPa∙m{sup 1/2}, respectively. The intragranular nano W dispersoids and ribbon like precipitates hinder crack propagation via crack deflection and bridging.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Structural and optical characterization of high-quality ZnO thin films deposited by reactive RF magnetron sputtering

Highlights: ► High-quality ZnO thin films were deposited at room temperature. ► Effect of O{sub 2} flow and RF sputtering voltages on properties of ZnO films were studied. ► O{sub 2}/Ar ratios played a key role in controlling optical properties of ZnO films. ► Photoluminescence intensity of the ZnO films strongly depended on O{sub 2}/Ar ratios. ► Crystallite size, stress and strain strongly depended on O{sub 2}/Ar ratios. - Abstract: ZnO thin films were deposited onto quartz substrates by radio frequency (RF) reactive magnetron sputtering using a Zn target. The structural and optical properties of the ZnO thin films were investigated comprehensively by X-ray diffraction (XRD), ultraviolet–visible and photoluminescence (PL) measurements. The effects of the oxygen content of the total oxygen–argon mixture and sputtering voltage in the sputtering process on the structural and optical properties of the ZnO films were studied systemically. The microstructural parameters, such as the lattice constant, crystallite size, stress and strain, were also calculated and correlated with the structural and optical properties of the ZnO films. In addition, the results showed that the crystalline quality of ZnO thin films improved with increasing O{sub 2}/Ar gas flow ratio from 2:8 to 8:2. XRD and PL spectroscopy revealed 800 V to be the most appropriate sputtering voltage for ZnO thin film growth. High-quality ZnO films with a good crystalline structure, tunable optical band gap as well as high transmittance could be fabricated easily by RF reactive magnetron sputtering, paving the way to obtaining cost-effective ZnO thin films transparent conducting oxides for optoelectronics applications.

36 MATERIALS SCIENCE↗

Reactive sintering of tungsten-doped high strength ZrB{sub 2}–SiC porous ceramics using metastable precursors

Graphical abstract: - Highlights: • Tungsten-doped porous ZrB{sub 2}–SiC specimens were fabricated by reactive sintering. • Both sintering and mechanical properties were improved by doping with tungsten. • Optimum concentration to obtain high mechanical properties was W/Zr (mol) = 0.05. • Sintering might be promoted by self-accelerated diffusion. • Mechanical properties might be improved by solid solution strengthening. - Abstract: Tungsten-doped porous ZrB{sub 2}-20 vol.% SiC specimens with a high strength skeleton were fabricated by reactive sintering using metastable reactants, i.e., as-synthesized amorphous hydrous ZrO{sub 2}–WO{sub 3}/ZrO{sub 2}, amorphous boron, nanocarbon, and β-SiC. Doping with tungsten clearly promoted sintering and improved mechanical properties; the optimum tungsten concentration to obtain high mechanical properties was investigated. A single-phase solid solution (Zr,W)B{sub 2} was formed in the specimens with tungsten. We suggest that sintering was promoted by self-accelerated diffusion owing to the formation of point defects caused by doping with tungsten. The improvement of mechanical properties could be attributed to solid solution strengthening.

36 MATERIALS SCIENCE↗

Ferroelectric and dielectric study of strontium tantalum based perovskite oxynitride films deposited by reactive rf magnetron sputtering

Highlights: • Oxynitride perovskite thin films were deposited by reactive sputtering. • Films are textured or epitaxially grown on MgO and Nb-SrTiO{sub 3} substrates. • Local piezoelectric and ferroelectric behavior was highlighted by PFM. • A 1600 nm-thick film presents a permittivity of 175 at 10 kHz and RT. • Permittivity is around 65 in high frequency range. - Abstract: Strontium and tantalum based oxynitride perovskite thin films were deposited by reactive magnetron sputtering. Epitaxial films deposited on Nb-SrTiO{sub 3} substrates show smooth surfaces with roughness values from 1.5 to 3.6 nm for a thickness of films in the range 20–1600 nm. The samples are yellow with band gap values around 2.35 eV. Piezo-force microscopy characterization pointed out the local piezoelectric and ferroelectric behavior of the oxynitride perovskite films. In the low frequency range, the 1600 nm-thick film exhibits a permittivity of 175 at 10 kHz, with dielectric losses of 0.055. Permittivity is lowered in high frequencies with a value around 65 obtained on a 1520 nm-thick film deposited on MgO substrate, which is textured with a preferential c-axis orientation. No accordability of the permittivity was highlighted at a macroscopic scale. The moderate crystallographic strain evidenced in the 20 nm thin film does not induce a high permittivity.

36 MATERIALS SCIENCE↗

Grain boundary scavenging through reactive sintering of strontium and iron in samarium doped ceria electrolyte for ITSOFC applications

Highlights: • Addition of iron and strontium to Samarium doped ceria by combustion method and sintered at 1000 °C, 1200 °C, 1300 °C. • Viscous phase sintering of iron at 1200 °C modified to reactive sintering of iron and strontium at 1300 °C. • Grain boundary activation energy lowered without compensating the grain activation energy. • The highest scavenging factor of 10.52 with the lowest activation energy of 1.02eV was achieved. - Abstract: Lowering the operational temperature of ceria based electrolytes is important for commercialization of solid oxide fuel cells. Here, we report the effect of iron, strontium and iron/strontium co-addition in samarium (20 mol %) doped ceria (SDC) with respect to sintering, microstructural modifications and ionic conductivity. The nanoparticle synthesized through glycine-nitrate combustion method was sintered at 1000, 1200 and 1300 °C. An increase in density was observed in iron doped SDC due to viscous flow sintering while co-addition of strontium and iron lead to the reactive sintering at 1300 °C by forming a eutectic liquid phase which resulted in the density of 99%. The presence of iron and strontium generated a compensatory tensile strain in the lattice and an enhancement in oxygen vacancy concentration which resulted in higher ionic conductivity. Co-addition of strontium and iron in SDC, not only increases the density but also reduces the activation energy for grain boundary conductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

3D printing via ambient reactive extrusion

Here, Additive Manufacturing (AM) has the potential to offer many benefits over traditional manufacturing methods in the fabrication of complex parts with advantages such as low weight, complex geometry, and embedded functionality. In practice, today’s AM technologies are limited by their slow speed and highly directional properties. To address both issues, we have developed a reactive mixture deposition approach that can enable 3D printing of polymer materials at over 100X the volumetric deposition rate, enabled by a greater than 10X reduction in print head mass compared to existing large-scale thermoplastic deposition methods, with material chemistries that can be tuned for specific properties. Additionally, the reaction kinetics and transient rheological properties are specifically designed for the target deposition rates, enabling the synchronized development of increasing shear modulus and extensive cross linking across the printed layers. This ambient cure eliminates the internal stresses and bulk distortions that typically hamper AM of large parts, and yields a printed part with inter-layer covalent bonds that significantly improve the strength of the part along the build direction. The fast cure kinetics combined with the fine-tuned viscoelastic properties of the mixture enable rapid vertical builds that are not possible using other approaches. Through rheological characterization of mixtures that were capable of printing in this process as well as materials that have sufficient structural integrity for layer-on-layer printing, a “printability” rheological phase diagram has been developed, and is presented here. We envision this approach implemented as a deployable manufacturing system, where manufacturing is done on-site using the efficiently-shipped polymer, locally-sourced fillers, and a small, deployable print system. Unlike existing additive manufacturing approaches which require larger and slower print systems and complex thermal management strategies as scale increases, liquid reactive polymers decouple performance and print speed from the scale of the part, enabling a new class of cost-effective, fuel-efficient additive manufacturing.

36 MATERIALS SCIENCE↗

Multiphase flow and multicomponent reactive transport model of the ventilation experiment in Opalinus clay

During the construction and operational phases of a high-level radioactive waste (HLW) repository constructed in a clay formation, ventilation of underground drifts will cause desaturation and oxidation of the rock. The Ventilation Experiment (VE) was performed in a 1.3 m diameter unlined horizontal microtunnel on Opalinus clay at Mont Terri underground research laboratory in Switzerland to evaluate the impact of desaturation on rock properties. A multiphase flow and reactive transport model of VE is presented here. The model accounts for liquid, vapor and air flow, evaporation/condensation and multicomponent reactive solute transport with kinetic dissolution of pyrite and siderite and local-equilibrium dissolution/precipitation of calcite, ferrihydrite, dolomite, gypsum and quartz. Model results reproduce measured vapor flow, liquid pressure and hydrochemical data and capture the trends of measured relative humidities, although such data are slightly overestimated near the rock interface due to uncertainties in the turbulence factor. Rock desaturation allows oxygen to diffuse into the rock and triggers pyrite oxidation, dissolution of calcite and siderite, precipitation of ferrihydrite, dolomite and gypsum and cation exchange. pH in the unsaturated rock varies from 7.8 to 8 and is buffered by calcite. Computed changes in the porosity and the permeability of Opalinus clay in the unsaturated zone caused by oxidation and mineral dissolution/precipitation are smaller than 5%. Therefore, rock properties are not expected to be affected significantly by ventilation of underground drifts during construction and operational phases of a HLW repository in clay.

54 ENVIRONMENTAL SCIENCES↗

Reprocessable polyhydroxyurethane networks reinforced with reactive polyhedral oligomeric silsesquioxanes (POSS) and exhibiting excellent elevated temperature creep resistance

The rapid development of covalent adaptable networks or vitrimers shows promise for addressing the long-standing recycling issues associated with conventional, permanently cross-linked thermosets. At the same time, it is important to demonstrate that properties of reprocessable polymer networks can be optimized to meet the ongoing demand for high-performance materials. We have fabricated reprocessable polyhydroxyurethane (PHU) network composites reinforced with reactive polyhedral oligomeric silsesquioxanes (POSS). With functionalized POSS serving as a fraction of the cross-linkers, the PHU–POSS network nanocomposites exhibit significantly enhanced storage modulus at the rubbery plateau region relative to the neat PHU network. With up to 10 wt% POSS loading, these network composites can undergo melt-state reprocessing at 140 °C with 100% property recovery associated with cross-link density. We also show that hydroxyurethane dynamic chemistry leads to excellent creep resistance at elevated temperature up to 90 °C and is unaffected by reactive incorporation of POSS. In conclusion, this study demonstrates the effectiveness of POSS as nanofillers for designing high-performance, organic-inorganic dynamic PHU networks with excellent reprocessability.

42 ENGINEERING↗

The influence of thermochemistry on the reactivity of propane, the pentane isomers and $n$-heptane in the low temperature regime

In this study, the influence of thermochemistry on the reactivity of fuels at low temperatures (600–1000 K) is studied here. Specifically, the effect of different sets of thermochemistry on chemical model predictions is explored, where various sets are calculated at different levels of theory in addition to recently updated group additivity values. Experimentally measured ignition delay times for propane, the pentane isomers and n-heptane are simulated using NUIGMech1.2 and replacing the thermochemistry of the low-temperature species with the calculated values. For propane, three different thermochemistry sets were calculated, namely CCSD(T)-F12/TZ-F12//B2PLYP-D3/TZ//B2PLYP-D3/TZ (QM1), CCSD(T)-F12/TZ-F12//B2PLYP-D3/TZ//ωB97X-D/TZ (QM2) and B2PLYP-D3/TZ/ωB97X-D/6-31G*//ωB97X-D/6-31G* (QM3). The QM2 results provide parameters to optimize new group additivity (NGA) values which are used to calculate the fourth set of thermochemistry. The model predictions using these four sets are compared to those using NUIGMech1.2 for propane. As the QM1 and QM2 calculations are expensive, the thermochemistry calculated from the QM3 and NGA calculations are used in the pentane isomer and n-heptane models. For all of the models, it is found that the thermochemistry of the species involved in the low-temperature reaction sequence ($RH$, $\dot{R}$, $RO_2H$, $R\dot{O}_2$, $\dot{Q}OOH$ and $\dot{O}_2QOOH$ species) significantly affect fuel reactivity. The NGA values were developed based on all of these species except $\dot{O}_2QOOH$ radicals. The thermochemistry of $\dot{O}_2QOOH$ species cannot be accurately calculated with the NGA representations due to the importance of non-next-nearest neighbor interactions of –OOH substitution. Further development of the NGA method to capture such interactions is in progress. Overall, the model developed using the NGA thermochemistry shows better agreement with experimental data than the model using thermochemistry from affordable and prominent QM methods, such as QM3. Based on the results presented for propane, the pentane isomers and n-heptane, the thermochemistry calculated using the NGA method can be used to model the oxidation of higher order hydrocarbons at low temperatures.

33 ADVANCED PROPULSION SYSTEMS↗

Influence of americium complexation on the radiation-induced chemical reactivity of sulfophenyl bistriazinyl pyridine (SO 3 -Ph-BTP) towards the nitrate radical

Sulfophenyl bistriazinyl pyridine (SO 3 -Ph-BTP) is a hydrophilic organic ligand used to separate actinides and lanthanides. Dose accumulation and time-resolved studies have previously provided insight into the radiolytic stability and degradation pathways of SO 3 -Ph-BTP in reprocessing environments, but no study has yet addressed the impact of minor actinide complexation on the radiation chemistry of this ligand. To begin to fill this knowledge gap, a systematic, time-resolved study exploring the reactivity of the nitrate radical (NO 3 • ) with SO 3 -Ph-BTP in the presence of trivalent americium, Am(III), has been conducted, which demonstrates enhanced reactivity (an order of magnitude faster) upon metal complexation.

38 - RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCL↗

Structural Basis of the Cross-Reactivity of Genetically Related Human Anti-HIV-1 mAbs: Implications for Design of V3-Based Immunogens

Human monoclonal antibodies 447-52D and 537-10D, both coded by the VH3 gene and specific for the third variable region (V3) of the HIV-1 gp120, were found to share antigen-binding structural elements including an elongated CDR H3 forming main-chain interactions with the N terminus of the V3 crown. However, water-mediated hydrogen bonds and a unique cation- sandwich stacking allow 447-52D to be broadly reactive with V3 containing both the GPGR and GPGQ crown motifs, while the deeper binding pocket and a buried Glu in the binding site of 537-10D limit its reactivity to only V3 containing the GPGR motif. Our results suggest that the design of immunogens for anti-V3 antibodies should avoid the Arg at the V3 crown, as GPGR-containing epitopes appear to select for B cells making antibodies of narrower specificity than V3 that carry Gln at this position.

08 HYDROGEN↗

Cr(VI) induces mitochondrial-mediated and caspase-dependent apoptosis through reactive oxygen species-mediated p53 activation in JB6 Cl41 cells

Cr(VI) compounds are known to cause serious toxic and carcinogenic effects. Cr(VI) exposure can lead to a severe damage to the skin, but the mechanisms involved in the Cr(VI)-mediated toxicity in the skin are unclear. The present study examined whether Cr(VI) induces cell death by apoptosis or necrosis using mouse skin epidermal cell line, JB6 Cl41 cells. We also investigated the cellular mechanisms of Cr(VI)-induced cell death. This study showed that Cr(VI) induced apoptotic cell death in a dose-dependent manner, as demonstrated by the appearance of cell shrinkage, the migration of cells into the sub-G1 phase, the increase of Annexin V positively stained cells, and the formation of nuclear DNA ladders. Cr(VI) treatment resulted in the increases of mitochondrial membrane depolarization and caspases activation. Electron spin resonance (ESR) and fluorescence analysis revealed that Cr(VI) increased intracellular levels of reactive oxygen species (ROS) such as hydrogen peroxide and superoxide anion radical in dose-dependent manner. Blockage of p53 by si-RNA transfection suppressed mitochondrial changes of Bcl-2 family composition, mitochondrial membrane depolarization, caspase activation and PARP cleavage, leading to the inhibition of Cr(VI)-induced apoptosis. Further, catalase treatment prevented p53 phosphorylation stimulated by Cr(VI) with the concomitant inhibition of caspase activation. These results suggest that Cr(VI) induced a mitochondrial-mediated and caspase-dependent apoptosis in skin epidermal cells through activation of p53, which are mainly mediated by reactive oxidants generated by the chemical.

60 APPLIED LIFE SCIENCES↗

Reactive oxygen species and oxidative DNA damage mediate the cytotoxicity of tungsten-nickel-cobalt alloys in vitro

Tungsten alloys (WA) have been introduced in an attempt to find safer alternatives to depleted uranium and lead munitions. However, it is known that at least one alloy, 91% tungsten-6% nickel-3% cobalt (WNC-91-6-3), causes rhabdomyosarcomas when fragments are implanted in rat muscle. This raises concerns that shrapnel, if not surgically removable, may result in similar tumours in humans. There is therefore a clear need to develop rapid and robust in vitro methods to characterise the toxicity of different WAs in order to identify those that are most likely to be harmful to human health and to guide development of new materials in the future. In the current study we have developed a rapid visual in vitro assay to detect toxicity mediated by individual WA particles in cultured L6-C11 rat muscle cells. Using a variety of techniques (histology, comet assay, caspase-3 activity, oxidation of 2'7'-dichlorofluorescin to measure the production of reactive oxygen species and whole-genome microarrays) we show that, in agreement with the in vivo rat carcinogenicity studies, WNC-91-6-3 was the most toxic of the alloys tested. On dissolution, it produces large amounts of reactive oxygen species, causes significant amounts of DNA damage, inhibits caspase-3, triggers a severe hypoxic response and kills the cells in the immediate vicinity of the alloy particles within 24 h. By combining these in vitro data we offer a mechanistic explanation of the effect of this alloy in vivo and show that in vitro tests are a viable alternative for assessing new alloys in the future.

60 APPLIED LIFE SCIENCES↗

Reactive oxygen species mediate arsenic induced cell transformation and tumorigenesis through Wnt/{beta}-catenin pathway in human colorectal adenocarcinoma DLD1 cells

Long term exposure to arsenic can increase incidence of human cancers, such as skin, lung, and colon rectum. The mechanism of arsenic induced carcinogenesis is still unclear. It is generally believed that reactive oxygen species (ROS) may play an important role in this process. In the present study, we investigate the possible linkage between ROS, {beta}-catenin and arsenic induced transformation and tumorigenesis in human colorectal adenocarcinoma cell line, DLD1 cells. Our results show that arsenic was able to activate p47{sup phox} and p67{sup phox}, two key proteins for activation of NADPH oxidase. Arsenic was also able to generate ROS in DLD1 cells. Arsenic increased {beta}-catenin expression level and its promoter activity. ROS played a major role in arsenic-induced {beta}-catenin activation. Treatment of DLD1 cells by arsenic enhanced both transformation and tumorigenesis of these cells. The tumor volumes of arsenic treated group were much larger than those without arsenic treatment. Addition of either superoxide dismutase (SOD) or catalase reduced arsenic induced cell transformation and tumor formation. The results indicate that ROS are involved in arsenic induced cell transformation and tumor formation possible through Wnt/{beta}-catenin pathway in human colorectal adenocarcinoma cell line DLD1 cells. - Highlights: > Arsenic activates NADPH oxidase and increases reactive oxygen species generation in DLD1 cells. > Arsenic increases {beta}-catenin expression. > Inhibition of ROS induced by arsenic reduce {beta}-catenin expression. > Arsenic increases cell transformation in DLD1 cells and tumorigenesis in nude mice. > Blockage of ROS decrease cell transformation and tumorigenesis induced by arsenic.

60 APPLIED LIFE SCIENCES↗

Arsenite activates NFκB through induction of C-reactive protein

C-reactive protein (CRP) is an acute phase protein in humans. Elevated levels of CRP are produced in response to inflammatory cytokines and are associated with atherosclerosis, hypertension, cardiovascular disease and insulin resistance. Exposure to inorganic arsenic, a common environmental toxicant, also produces cardiovascular disorders, namely atherosclerosis and is associated with insulin-resistance. Inorganic arsenic has been shown to contribute to cardiac toxicities through production of reactive oxygen species (ROS) that result in the activation of NFκB. In this study we show that exposure of the hepatic cell line, HepG2, to environmentally relevant levels of arsenite (0.13 to 2 μM) results in elevated CRP expression and secretion. ROS analysis of the samples showed that a minimal amount of ROS are produced by HepG2 cells in response to these concentrations of arsenic. In addition, treatment of FvB mice with 100 ppb sodium arsenite in the drinking water for 6 months starting at weaning age resulted in dramatically higher levels of CRP in both the liver and inner medullary region of the kidney. Further, mouse Inner Medullary Collecting Duct cells (mIMCD-4), a mouse kidney cell line, were stimulated with 10 ng/ml CRP which resulted in activation of NFκB. Pretreatment with 10 nM Y27632, a known Rho-kinase inhibitor, prior to CRP exposure attenuated NFκB activation. These data suggest that arsenic causes the expression and secretion of CRP and that CRP activates NFκB through activation of the Rho-kinase pathway, thereby providing a novel pathway by which arsenic can contribute to metabolic syndrome and cardiovascular disease. -- Highlights: ► Exposure to arsenic can induce the expression and secretion of CRP. ► Mice treated with NaAsO{sub 2} showed higher levels of CRP in both the liver and kidney. ► mIMCD-3 were stimulated with CRP which resulted in activation of NFκB. ► CRP activates NFκB through activation of the Rho-kinase pathway. ► Data provide novel pathway for arsenic role in metabolic and cardiovascular disease.

60 APPLIED LIFE SCIENCES↗