Search NASA⌕ Search

SEARCH · Search NASA

Results for “WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Effects of Postweld Heat Treatment on Microstructure and Properties of Laser-Welded Ti-24Al-15Nb Alloy Joint

The microstructure evolution and mechanical properties of laser-welded joints of Ti-24Al-15Nb alloy under different postweld heat treatment (PWHT) conditions were systematically investigated. The results show that the microstructure is very sensitive to PWHT temperatures. The weld zone consists of B2 and O phases after PWHT. With the PWHT temperatures increasing from 850 to 1000 °C, the amount of O phase decreases gradually, while the grains of O precipitates become coarser. After PWHT, there are some thin acicular O precipitates in heat-affected zone (HAZ), and the decomposition of α{sub 2}-phase caused by niobium diffusion can be observed in the HAZ. The PWHT can significantly increase the microhardness of joints, resulting from O phase precipitation hardening effect. The tensile strength and elongation of joints can be remarkably improved after PWHT, which was closely related to the strengthening effect of O precipitates and slip transmission between O and B2 phases. In addition, the results indicate that the best mechanical properties can be achieved only when the number and size of O phase and B2 phase are the best match.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Neutron Diffraction Residual Stress Study of a AA2219-T87 Self-Reacting Friction Stir Weld

2219-T87 is a precipitation hardenable aluminum-copper alloy which sees wide use in structural aerospace components. Thick panels of this alloy are joined via self-reacting friction welding (SRFSW); however, this thermomechanical process can result in significant loss of the alloy’s strengthening precipitates and large residual stresses which are detrimental to mechanical behavior and performance. High-resolution maps of the residual strain and stress states along the normal, transverse, and longitudinal directions of 2219-T87 SRFSW were obtained using neutron diffraction measurements. Residual stress had the highest tensile value in the heat-affected zone (HAZ) and the largest compressive stress in the base metal region of the normal and transverse directions. Line profile residual stress distributions displayed an “M”-shaped distribution in each direction with the longitudinal direction being the most pronounced while 2D residual stresses displayed an hourglass-shaped pattern. Further, average maximal longitudinal residual stress values ranged from 60.6 to 85.6% of yield. Microhardness testing across the transverse weld section produced a “V”-shaped curve with slight hardness recovery in the stir zone. Maximal and minimal microhardness values were observed in the base metal (154 HV) and thermomechanically affected zone (82 HV), respectively. Microstructural evolution was recorded using optical microscopy and showed decreasing grain size from the HAZ to the stir zone.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tool-workpiece stick-slip conditions and their effects on torque and heat generation rate in the friction stir welding

Friction stir welding (FSW) has found increased applications in automotive and aerospace industries due to its advantages of solid-state bonding, no fusion and melting, and versatility in various working conditions and material combinations. However, the relationship among processing parameters, material properties, and bonding extent and fidelity remains largely empirical, primarily because of the lack of the mechanistic understanding of the tool-workpiece frictional behavior that affects our subsequent understanding of microstructural evolution and interface bonding formation. While the tool-workpiece stick-slip condition is believed to dictate the resulting torque and heat generation rate during the welding process, it remains rare and elusive to conduct a quantitative experimental measurement of such interfacial field. On the other hand, numerical simulations based on Computational Fluid Dynamics (CFD) rely on ad hoc assumptions of interfacial pressure and shear-stress conditions, but predictions can only be validated via the medium- and far-range temperature field which is known to be insensitive to the interfacial frictional behavior. This work first presents a comparison among two CFD-based simulation methodologies and the Coupled Eulerian Lagrangian (CEL) model in finite element method, the last of which uses the Coulomb friction so that the stick-slip is naturally developed. Based on the Hill-Bower similarity relationship in the contact analysis, an analytical model is developed here to prove why a constant stick-slip fraction will be developed in the steady state, to correlate the stick-slip fraction to processing parameters such as the tool spin rate, and further to derive dimensionless functions for torque and heat-generation-rate predictions. Pros and cons of various numerical approaches in predicting stick-slip are discussed, and our analytical model has been found to agree well with our numerical simulation and literature experimental results. These analyses provide the critical strain-rate and temperature fields that are needed for the bonding analysis in our future work.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Direct observation of pore formation mechanisms during LPBF additive manufacturing process and high energy density laser welding

Laser powder bed fusion (LPBF) is a 3D printing technology that can print parts with complex geometries that are unachievable by conventional manufacturing technologies. However, pores formed during the printing process impair the mechanical performance of the printed parts, severely hindering their widespread application. Here, we report six pore formation mechanisms that were observed during the LPBF process. Our results in this study reconfirm three pore formation mechanisms - keyhole induced pores, pore formation from feedstock powder and pore formation along the melting boundary during laser melting from vaporization of a volatile substance or an expansion of a tiny trapped gas. We also observe three new pore formation mechanisms: (1) pore trapped by surface fluctuation, (2) pore formation due to depression zone fluctuation when the depression zone is shallow and (3) pore formation from a crack. The results presented here provide direct evidence and insight into pore formation mechanisms during the LPBF process, which may guide the development of pore elimination/mitigation approaches. Since certain laser processing conditions studied here are similar to the situations in high energy density laser welding, the results presented here also have implications for laser welding.

42 ENGINEERING↗
DOE OSTI2021

Optimization of the microstructure and mechanical properties of electron beam welded high-strength medium-entropy alloy (NiCoCr) 94 Al 3 Ti 3

For this work, the weldability and effects of subsequent heat treatment on the microstructure and mechanical properties of the medium-entropy alloy (MEA) (NiCoCr) 94 Al 3 Ti 3 have been explored using electron beam welding (EBW). It was found that EBW joints consist of a supersaturated f.c.c. matrix with coarse, asymmetric columnar grains (17.7–24 μm). The fraction of twins and Σ3 n CSL boundaries in weld joints was only 10% of that in the base metal, a value which increased to 30% after aging at 800 °C. The aging also led to improvements in the hardness, tensile strength, and work hardening rate, a result of the precipitation of a high volume fraction (0.29–0.33) of ultrafine (15–17.4 nm dia.) coherent spherical L1 2 -structured particles. The contributions of the L1 2 nanoparticles and Hall-Petch strengthening to the yield strength were estimated to be 537–573 MPa and 105–123 MPa, respectively. The MEA shows excellent weldability and, after aging, good strength (YS~1098 MPa, UTS~1368 MPa) and elongation to failure (~11%) by ductile fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Adaptive relay autotuning under static and non-static disturbances with application to friction stir welding

When a traditional relay feedback test is biased, asymmetry is induced, erroneous system identification occurs, and the test may stop oscillating. Adaptive methods which restore symmetry to the relay test are developed, and additional methods are presented to detect and recover from a non-oscillation condition. This is demonstrated both in simulation and in a process with significant transients and disturbances - friction stir welding (FSW). In testing, it is shown that the adaptive method is able to restore symmetry even in the presence of severe and changing disturbances, including after the weld plunge where temperature gradients change rapidly. Finally, these improvements enable system identification of systems such as FSW in a more robust and accurate manner.

42 ENGINEERING↗
DOE OSTI2020

Multi-scale characterization and simulation of impact welding between immiscible Mg/steel alloys

Vaporizing foil actuator spot welding method is used in this paper to join magnesium alloy AZ31 and uncoated high-strength steel DP590, which are typically considered as un-weldable due to their high physical property disparities, low mutual solubility, and the lack of any intermetallic phases. Characterization results from scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM) of the weld interface indicate that the impact creates an Mg nanocrystalline interlayer with abundant Fe particles. The interlayer exhibits intact bonding with both DP590 and AZ31 substrates. To investigate the fundamental bond formation mechanisms at the interface, a finite element (FE)-based process simulation is first performed to calculate the local temperature and deformation at the interface under the given macroscopic experimental condition. Finally, taking the FE results at the interface as inputs, molecular dynamics (MD) simulations are conducted to study the interlayer formation at the Mg/Fe interface during the impact and cooling. The results found a high velocity shearing-induced mechanical mixing mechanism that mixes Mg/Fe atoms at the interface and creates the interlayer, leading to the metallurgical bond between Mg/steel alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of friction stir welding and self-ion irradiation on dispersoid evolution in oxide dispersion strengthened steel MA956 up to 25 dpa

Here, the effect of ion irradiation on the microstructure of oxide dispersion strengthened (ODS) MA956 steel, before and after friction stir welding (FSW), was studied. Both the base material (BM) and welded stir zone (SZ) were irradiated with 5 MeV Fe ++ ions at 450 °C up to 25 displacements per atom (dpa). Characterization was performed using scanning transmission electron microscopy (STEM) and atom probe tomography (APT), with particular emphasis on the Y—Al—O dispersoid characteristics and dislocation microstructures. After irradiation, the dispersoids in the BM increased in diameter and decreased in number density, which was explained by an Ostwald ripening mechanism. FSW caused significant coarsening and agglomeration of the dispersoids. After irradiation, both the diameter and number density of the SZ dispersoids increased, which was explained by an irradiation-enhanced diffusion mechanism. Dislocation loop and network behavior was also characterized and large dislocation loops of ≈20 nm diameter formed by 1 dpa in both the BM and SZ samples, whereas the network density remained nearly constant with irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Twining and dynamic recrystallization in austenitic Alloy 718 during friction welding

Highlights: • DDRX was the primary grain refinement mechanism in friction welding of Alloy 718. • Two models were developed to explain the twin formation mechanism. • Intragranular twins were caused by grain boundary growth incidents. • Intergranular twin boundaries were ascribed to boundary growth stagnation. - Abstract: Quantitative boundary misorientation analysis verified that discontinuous dynamic recrystallization (DDRX) was the primary grain refinement mechanism in friction welding of Alloy 718. Two models were developed to explain the formation mechanism of intragranular twins and intergranular twins, respectively. Intragranular twins were caused by grain boundary growth incidents. After twin initiation, the twin boundary migrated toward the plastic-deformed grain interior to reduce the stored energy. Additionally, intergranular twin boundaries were ascribed to boundary growth stagnation. When boundary growth stagnation occurred, twin boundaries could form and altered the orientation of the boundary migration front, so that boundary migration could progress, leaving a single twin boundary behind.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Influencing mechanism of Al-containing Zn coating on interfacial microstructure and mechanical properties of friction stir spot welded Mg–steel joint

Highlights: • Al-containing Zn coating improved Mg–steel interfacial wettability during friction stir spot welding (FSSW). • Pre-existing Al{sub 5}Fe{sub 2} phase in coating on steel surface promoted Mg–steel metallurgical bonding. • A high tensile-shear load of 4.3 kN was obtained in FSSW AZ31–steel joint. - Abstract: 2.4 mm thick AZ31 Mg alloy sheet and 1.5 mm Q234 steel sheet with a hot-dipped Al-containing Zn coating were friction stir spot welded (FSSW) using a pinless tool. It was shown that the Al-containing Zn coating played a crucial role in joining the Mg alloy and steel during FSSW. The Zn coating observably improved the Mg–steel interfacial wettability during FSSW, and the Al{sub 5}Fe{sub 2} phase in the Zn coating on the steel substrate surface promoted the metallurgical bonding of Mg alloy and steel. It was confirmed that the Al{sub 5}Fe{sub 2} phase on the steel surface resulted from the reaction between the steel substrate and the Al in the Zn coating during hot-dipping, and was not related to the Al-containing Mg alloy substrate. The tensile-shear load of the FSSW Mg–steel joint reached 4.3 kN. The fracture of the joint occurred along the interface on the steel substrate side. The interface between the Al{sub 5}Fe{sub 2} layer and Mg alloy substrate was the weakest region of the Mg–steel joint.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Multi-scale mechanical modeling of Al-steel resistance spot welds

A multi-scale finite element modeling approach was developed to study the deformation and fracture behavior of Al-steel resistance spot welds. First, a micro-scale model was applied to simulate the mechanical responses of the intermetallic compound (IMC) layer having various morphologies and thicknesses under tensile and shear loading conditions. Second, the predicted tensile and shear strength of the IMC layer, that varied along the joint interface per the IMC layer morphology and thickness variation, was then introduced into 3D macro-scale models to predict the overall mechanical performance of weld coupons under coach peel, lap shear and cross-tension testing conditions. In conclusion, the numerical predictions agreed reasonably well with the experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Laser weld-induced formation of amorphous Mn–Si precipitate in 304 stainless steel

In this paper, we report the formation of partially amorphous Mn-Si precipitates due to laser welding of face centered cubic (fcc) 304 stainless steel. Transmission electron microscopy and precession electron diffraction studies in the heat affected zone (HAZ) of the weldment indicate the formation of these precipitates in grain interiors. Precipitates have MnSi stoichiometry and the partially crystalline regions have a lattice constant of 0.45 nm. It is surmised that the rapid cooling rates during the laser weld melt pool solidification process may be sufficient to inhibit the complete crystallization of these precipitates.

304 stainless steel↗
DOE OSTI2018

Strain and distortion monitoring during arc welding by 3D digital image correlation

A novel three-dimensional (3D) digital image correlation (DIC) approach using a stereovision system was developed to measure the evolution of strain and distortion near the fusion zone during the gas tungsten arc welding process. Unlike the previously reported two-dimensional (2D) DIC approach using a single camera, the 3D DIC method was immune to the out-of-plane displacement and was capable of measuring 3D deformation. Both 2D and 3D DIC approaches in welding applications were based on the utilisation of the novel high-temperature speckle and the pulsed laser illumination plus bandpass filters. However, the speckle pattern was partially specular reflective causing issues in subset matching in the 3D approach. A new algorithm and experimental procedure was incorporated to solve this problem.

47 OTHER INSTRUMENTATION↗
DOE OSTI2018

Development of Novel Functionally Graded Transition Joints for Improving the Creep Strength of Dissimilar Metal Welds in Nuclear Applications

Steam generators of the small modular Very High Temperature Reactor (VHTR) will require use of Alloy 800 and 2.25Cr-1Mo steel in different regions depending on temperature and corrosion resistance requirements. As a result, Dissimilar Metal Welds (DMWs) between these two materials are critical for design, development, and manufacturing of the VHTR. DMWs are also used in many other applications in the power generation and petrochemical industries. Experience has demonstrated that failures of such DMWs can occur prematurely well below the expected creep life of either base metal, and these failures have significant consequences in terms of plant reliability, safety, and economic impact. These DMWs failures are caused by the abrupt change in composition that occurs at the weld interface between the two alloys. In this research, the concept of developing and optimizing Graded Transition Joints (GTJ) was developed through an integrated modeling and experimental approach. With GTJs, the composition is gradually graded between the two alloys, thus eliminating the sharp change in composition that causes failure. Microstructural modeling was first conducted to identify the optimum grade length required for improved resistance to carbon diffusion that is largely responsible for premature failure. Next, GTJs were fabricated and characterized in detail to understand how the microstructure evolves during fabrication and long term aging. Finally, the creep behavior of the GTJs was investigated and compared to that of conventional DMWs to demonstrate the superior creep strength of the GTJs. The results of this research provide significant insight into design, fabrication, microstructural evolution, and resultant performance of GTJs that can be used for reducing or eliminating DMW failures in a number of high temperature applications. The results also demonstrate that the GTJs can be readily fabricated with either conventional or additive manufacturing processes, and detailed guidelines are provided on the length of grades needed for optimal performance. The results of this research benefits the general public by improving the reliability of power generation and petrochemical plants that rely on DMWs for safe and reliable operation to deliver power and other products.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Rotary Table Design for the Modular In-Chamber Electron Beam Welding System

The Modular In-Chamber Electron Beam Welding (MIC-EBW) system which is being designed and assembled under DOE Projects DE-NE0008846 (Phase 1--completed) and DE-NE0009039 (Phase 2—in progress) includes several major components: four modules (the lower vacuum module, electron beam module, a spacer module, and a lid), a robust rotary table, large vacuum pumps/system, electron beam welding system controls/power supply, and an electron beam generator/gun. Many of these components and their functions were described in the earlier EPRI-DOE report 3002018146. This report provides an overview of one of the primary components, the rotary table, that has been designed and will be manufactured by Rusach International in Phase 2 of the project.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2019

Current Regulation in Contact Welding

Algorithms for current stabilization in the control of contact welding are considered. The proposed method for specifying and maintaining the welding current permits correction of the thyristor firing angle by means of an approximate formula taking account of the measured current-pulse parameters in phase regulation. The proposed method simplifies the equipment and increases the efficiency of regulation.

42 ENGINEERING↗
DOE OSTI2020

Multi-objective optimization of peel and shear strengths in ultrasonic metal welding using machine learning-based response surface methodology

Ultrasonic metal welding (UMW) is a solid-state joining technique with varied industrial applications. Despite of its numerous advantages, UMW has a relative narrow operating window and is sensitive to variations in process conditions. As such, it is imperative to quantitatively characterize the influence of welding parameters on the resulting joint quality. The quantification model can be subsequently used to optimize the parameters. Conventional response surface methodology (RSM) usually employs linear or polynomial models, which may not be able to capture the intricate, nonlinear input-output relationships in UMW. Furthermore, some UMW applications call for simultaneous optimization of multiple quality indices such as peel strength, shear strength, electrical conductivity, and thermal conductivity. To address these challenges, this paper develops a machine learning (ML)-based RSM to model the input-output relationships in UMW and jointly optimize two quality indices, namely, peel and shear strengths. The performance of various ML methods including spline regression, Gaussian process regression (GPR), support vector regression (SVR), and conventional polynomial regression models with different orders is compared. A case study using experimental data shows that GPR with radial basis function (RBF) kernel and SVR with RBF kernel achieve the best prediction accuracy. The obtained response surface models are then used to optimize a compound joint strength indicator that is defined as the average of normalized shear and peel strengths. In addition, the case study reveals different patterns in the response surfaces of shear and peel strengths, which has not been systematically studied in the literature. While developed for the UMW application, the method can be extended to other manufacturing processes.

42 ENGINEERING↗