Search NASA⌕ Search

SEARCH · Search NASA

Results for “buffer layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Structure and interaction in 2D assemblies of tobacco mosaic viruses

We created two-dimensional (2D) assemblies of tobacco mosaic viruses (TMVs) and characterized their structures using Atomic Force Microscopy (AFM) and X-ray scattering. The TMVs were adsorbed on an oppositely charged, fluid lipid monolayer supported by a solid substrate and submerged in a buffer solution. The lipid monolayer confined the viral particles within a plane, while providing them with lateral mobility so that overall the TMV assembly behaved like a 2D liquid. We controlled the inter-particle interaction by adjusting the chemical condition in the buffer to induce ordered TMV assemblies. We found that the presence of the lipid layer was essential for forming ordered TMV assemblies. Packed TMV assemblies formed on the lipid layer, with an average inter-particle spacing of 42 nm. By introducing Ca2+ ions into the buffer solution, we were able to improve the in-plane order within the TMV assemblies and reduce the average inter-particle spacing to 20 nm, compared to the TMV diameter of 18 nm. Quantitative analysis of the X-ray scattering data shows that the structural order within the TMV assemblies prepared under a Ca{sup 2+}-free buffer solution is consistent with purely repulsive, electrostatic inter-particle interaction. In contrast, the structural order within Ca{sup 2+}-induced TMV assemblies is consistent with the behavior of a fluid of sticky rods, implying the presence of a strong attraction between TMVs. In addition to the screening of Coulomb repulsion, this behavior is likely the result of counterion-induced as well as membrane-mediated attractions.

36 MATERIALS SCIENCE↗

Impact of Arsenic- and Indium-Terminated InGaAs Stressors on Carrier Confinement, Strain, Defects, and Transport Properties of Tensile-Strained Ge

Device-quality tensile-strained Ge (ε-Ge) grown on a large bandgap semiconductor with superior electrical and optical carrier confinement is essential for group-IV-based optoelectronics. Properties of ε-Ge active layers synthesized on In 0.24 Ga 0.76 As buffers with two different surface terminations─arsenic-rich and indium-rich─were experimentally demonstrated, highlighting the factors not considered in theoretical calculations. High-resolution X-ray diffraction and Raman spectroscopy analyses of these ε-Ge/In 0.24 Ga 0.76 As heterostructures confirmed the fully strained (1.6%) and partially relaxed (0.82%) nature of the ε-Ge bonded with arsenic-terminated (Ge As-terminated ) and indium-terminated (Ge In-terminated ) In 0.24 Ga 0.76 As stressors, respectively. High-resolution cross-sectional transmission electron microscopy showed a coherent, sharp, and fully strained ε-Ge/In 0.24 Ga 0.76 As heterointerface in the Ge As-terminated heterostructure, whereas microtwin defects were present in the Ge In-terminated heterostructure. These heterostructures were further characterized by evaluating the minority carrier lifetimes, high for Ge As-terminated (525 ns) and low for Ge In-terminated (69 ns), using the photoconductive decay technique. Moreover, band alignment was constructed using X-ray photoelectron spectroscopy, where the Ge As-terminated heterostructure revealed that both holes and electrons were confined within the ε-Ge active layer as a type-I band alignment with ΔE V, As-terminated = 0.22 eV and ΔE C,As-terminated = 0.38 eV. On the other hand, the Ge In-terminated heterostructure exhibited a type-II band alignment with ΔE V,In-terminated = – 0.02 eV and ΔE C,In-terminated = 0.53 eV. Furthermore, the magnetotransport properties revealed high mobility (321 cm 2 /(V s)) with single-electron transport in Ge As-terminated heterostructure and low mobility (3.34 cm 2 /(V s)) with multihole transport in the Ge In-terminated heterostructure. Therefore, preferring the ε-Ge on the arsenic-rich surface of In 0.24 Ga 0.76 As stressor over the indium-rich surface during material synthesis offers device-quality materials with high carrier lifetime and superior carrier confinement, which can provide an opportunity to fabricate efficient group-IV-based optoelectronic devices.

36 MATERIALS SCIENCE↗

Irradiation performance of AGR-1 high temperature reactor fuel

The AGR-1 experiment contained 72 low-enriched uranium oxide/uranium carbide TRISO coated particle fuel compacts in six capsules irradiated to burnups of 11.2 to 19.6% FIMA, with zero TRISO coating failures detected during the irradiation. The irradiation performance of the fuel including the extent of fission product release and the evolution of kernel and coating microstructures was evaluated based on detailed examination of the irradiation capsules, the fuel compacts, and individual particles. Fractional release of 110m Ag from the fuel compacts was often significant, with capsule-average values ranging from 0.01 to 0.38. Analysis of silver release from individual compacts indicated that it was primarily dependent on fuel temperature history. Europium and strontium were released in small amounts through intact coatings, but were found to be significantly retained in the outer pyrocarbon and compact matrix. The capsule-average fractional release from the compacts was 1 × 10 –4 to 5 × 10 –4 for 154 Eu and 8 × 10 –7 to 3 × 10 –5 for 90 Sr. The average 134 Cs fractional release from compacts was <3 × 10 –6 when all particles maintained intact SiC. An estimated four particles out of 2.98 × 10 5 in the experiment experienced partial cesium release due to SiC failure during the irradiation, driving 134 Cs fractional release in two capsules to approximately 10 –5 . Identification and characterization of these particles has provided unprecedented insight into the nature and causes of SiC coating failure in high-quality TRISO fuel. In general, changes in coating morphology were found to be dominated by the behavior of the buffer and inner pyrolytic carbon (IPyC), and infrequently observed SiC layer damage was usually related to cracks in the IPyC. Palladium attack of the SiC layer was relatively minor, except for the particles that released cesium during irradiation, where SiC corrosion was found adjacent to IPyC cracks. In conclusion, palladium, silver, and uranium were found in the SiC layer of irradiated particles, and characterization of these elements within the SiC microstructure is the subject of ongoing focused study.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Using hole injection layers for decreased metastability and higher performance in Cu(In,Ga)Se 2 devices

In this work, modifications to the buffer structure in Cu(In,Ga)Se 2 (CIGS) solar cells are examined in terms of power conversion efficiency and metastability. Varying amounts of thin hole-injecting layers are introduced at different locations in the CIGS/Zn(O,S) device structure. It is found that such layers simultaneously increase performance and decrease metastability. The most effective variant produces devices without metastability and with higher efficiency than the CdS-only controls. The most effective location for hole injection is found to be between the Zn(O,S) buffer and the transparent conductor. At this location, passivation of the CIGS surface is not a function of the hole injection layer, and thus a variety of materials with appropriate band-edge energies should achieve the same purpose.

36 MATERIALS SCIENCE↗

Material Performance of Fully-Ceramic Micro-Encapsulated Fuel under Selected LWR Design Basis Scenarios (Final Report)

The extension to LWRs of the use of Deep-Burn coated particle fuel envisaged for HTRs has been investigated. TRISO coated fuel particles are used in Fully-Ceramic Microencapsulated (FCM) fuel within a SiC matrix rather than the graphite of HTRs. TRISO particles are well characterized for uranium-fueled HTRs. However, operating conditions of LWRs are different from those of HTRs (temperature, neutron energy spectrum, fast fluence levels, power density). Furthermore, the time scales of transient core behavior during accidents are usually much shorter and thus more severe in LWRs. The PASTA code was updated for analysis of stresses in coated particle FCM fuel. The code extensions enable the automatic use of neutronic data (burnup, fast fluence as a function of irradiation time) obtained using the DRAGON neutronics code. An input option for automatic evaluation of temperature rise during anticipated transients was also added. A new thermal model for FCM was incorporated into the code; so-were updated correlations (for pyrocarbon coating layers) suitable to estimating dimensional changes at the high fluence levels attained in LWR DB fuel. Analyses of the FCM fuel using the updated PASTA code under nominal and accident conditions show: (1) Stress levels in SiC-coatings are low for low fission gas release (FGR) fractions of several percent, as based on data of fission gas diffusion in UO 2 kernels. However, the high burnup level of LWR-DB fuel implies that the FGR fraction is more likely to be in the range of 50-100%, similar to Inert Matrix Fuels (IMFs). For this range the predicted stresses and failure fractions of the SiC coating are high for the reference particle design (500 μm kernel diameter, 100 μm buffer, 35 μm IPyC, 35 μm SiC, 40 μm OPyC). A conservative case, assuming 100% FGR, 900K fuel temperature and 705 MWd/kg (77% FIMA) fuel burnup, results in a 8.0 x 10 -2 failure probability. For a 'best-estimate' FGR fraction of 50% and a more modest burnup target level of 500 MWd/kg ,the failure probability drops below 2.0 x 10 -5 , the typical performance of TRISO fuel made under the German HTR research program. An optimization study on particle design shows improved performance if the buffer size is increased from 100 to 120 μm while reducing the OPyC layer. The presence of the latter layer does not provide much benefit at high burnup levels (and fast fluence levels). Normally the shrinkage of the OPyC would result in a beneficial compressive force on the SiC coating. However, at high fluence levels the shrinkage is expected to turn into swelling, resulting in the opposite effect. However, this situation is different when the SiC-matrix, in which the particles are embedded, is also considered: the OPyC swelling can result in a beneficial compressive force on the SiC coating since outward displacement of the OPyC outer surface is inhibited by the presence of the also-swelling SiC matrix. Taking some credit for this effect by adopting a 5 μm SiC-matrix layer, the optimized particle (100 μm buffer and 10 μm OPyC), gives a failure probability of 1.9 x 10 -4 for conservative conditions. During a LOCA transient, assuming core re-flood in 30 seconds, the temperature of the coated particle can be expected to be about 200K higher than nominal temperature (900K). For this event the particle failure fraction for a conservative case is 1.0 x 10 -2 , for the optimized particle design. For a FGR-fraction of 50% this value reduces to 6.4 x 10 -4 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Electrical properties and deep traps spectra of N-polar and Ga-polar AlGaN films grown by molecular beam epitaxy in a wide composition range

The polarity type, surface morphology, electrical properties, and deep trap spectra were studied for undoped Al{sub x}Ga{sub 1-x}N films (x=0-0.6) grown by molecular beam epitaxy on on-axis (0001) sapphire using composite buffers consisting of low temperature (LT) AlN nucleation layer, AlN, and AlN/AlGaN superlattice. It is shown that the films grow with N-polarity if the LT AlN layer is deposited under N-rich conditions and with Ga-polarity for the LT AlN layers deposited under Al-rich conditions. For both polarities the film morphology was acceptable for fabrication of typical GaN-based devices. It is demonstrated that the Ga-polar AlGaN films are heavily compensated p-type, with the dominant acceptors believed to be due to C. N-polar films are n type, with the residual donors pinning the Fermi level being most likely due to Si. N-polar films show a high concentration of deep electron traps.

36 MATERIALS SCIENCE↗

A microstructural approach toward the effect of thickness on semiconductor-to-metal transition characteristics of VO{sub 2} epilayers

We report the control of semiconductor to metal transition in VO{sub 2}(010) epilayers integrated with Si(100) substrates buffered with an NiO[111]/YSZ[100] intermediate layer. VO{sub 2} epitaxial thin films were grown at different thicknesses varying from 10 to 200 nm using pulsed laser deposition technique. An epitaxial relationship of VO{sub 2}(010)‖NiO(111)‖ YSZ(001)‖Si(001) and VO{sub 2}[100]‖NiO[110]‖ YSZ[100]‖Si[100] was established at room temperature. The crystallographic alignment across the VO{sub 2}/NiO interface changes to VO{sub 2}(100)‖NiO(111) and VO{sub 2}[001]‖NiO[110] at the temperature of growth giving rise to a misfit strain of about 33.5% and 3.0% along two orthogonal in-plane orientations. The transition temperature was observed to vary from about 353 to 341 K, the transition amplitude increased by about five orders of magnitude, and the hysteresis decreased to about 3 K, as the thickness of VO{sub 2} layers increased from about 10 to 200 nm. These observations were explained based on strain characteristics, overall defect content and grain boundaries, and phenomenological thermodynamic models.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structure and Interaction in 2D Assemblies of Tobacco Mosaic Viruses

We created two-dimensional (2D) assemblies of tobacco mosaic viruses (TMVs) and characterized their structures using Atomic Force Microscopy (AFM) and X-ray scattering. The TMVs were adsorbed on an oppositely charged, fluid lipid monolayer supported by a solid substrate and submerged in a buffer solution. The lipid monolayer confined the viral particles within a plane, while providing them with lateral mobility so that overall the TMV assembly behaved like a 2D liquid. We controlled the inter-particle interaction by adjusting the chemical condition in the buffer to induce ordered TMV assemblies. We found that the presence of the lipid layer was essential for forming ordered TMV assemblies. Packed TMV assemblies formed on the lipid layer, with an average inter-particle spacing of 42 nm. By introducing Ca{sup 2+} ions into the buffer solution, we were able to improve the in-plane order within the TMV assemblies and reduce the average inter-particle spacing to 20 nm, compared to the TMV diameter of 18 nm. Quantitative analysis of the X-ray scattering data shows that the structural order within the TMV assemblies prepared under a Ca{sup 2+}-free buffer solution is consistent with purely repulsive, electrostatic inter-particle interaction. In contrast, the structural order within Ca{sup 2+}-induced TMV assemblies is consistent with the behavior of a fluid of sticky rods, implying the presence of a strong attraction between TMVs. In addition to the screening of Coulomb repulsion, this behavior is likely the result of counterion-induced as well as membrane-mediated attractions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thawing seasonal ground ice: An important water source for boreal forest plants in Interior Alaska

Little is known about the ecological impacts of permafrost degradation on water fluxes in boreal ecosystems, such as those in Interior Alaska. Low plant water stress suggests a reliance on a diversity of water sources. In addition to rainfall, we hypothesize that deep soil water derived from thawing seasonal ground ice (TSGI) supports plants during dry periods. We analyzed water stable isotopes from soils, plants, ice, and rain collected from stable and unstable permafrost sites. We found that TSGI provides a background water source for plants during wet years (at least 10–20%) and a stable source during dry years (at least 30–50%) and early in the growing season (60–80% in wet and dry years). Plant water uptake patterns “track” the soil thawing front, using deep and shallow layers in wet years and deep layers during dry years. This plasticity allows boreal plants to cope with seasonal drought and exploit available water sources. The availability of TGSI depends on the amount of rainfall the prior year and on permafrost stability. Thawing permafrost may reduce the buffering capacity of TGSI due to less seasonal ice from greater drainage and/or a deeper active layer. This study demonstrates the importance of two buffering mechanisms for plants to cope with rainfall variability within boreal forest underlain by permafrost—availability of TSGI and plasticity in water uptake patterns. We suggest that plant utilization of stored water may be why evapotranspiration in northern latitudes can exceed growing season precipitation.

54 ENVIRONMENTAL SCIENCES↗

Generation of a Photoacoustic Signal in Two-Layer Transparent Samples on an Absorbing Substrate

A theory of generation of a photoacoustic signal in a two-layer transparent sample on an absorbing substrate to a buffer gas of a photoacoustic cell has been developed. We have shown that the frequency dependence of the photoacoustic signal amplitude excited in the absorbing substrate obeys the law ∝ ω{sup –1}, when a free path of photons is less than the thermal diffusion length, and is proportional to ω{sup –3/2} in the opposite case.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The role of AlGaN buffers and channel thickness in the electronic transport properties of Al{sub x}In{sub 1–x}N/AlN/GaN heterostructures

We try to theoretically analyze the reported experimental data of the Al{sub x}In{sub 1–x}N/AlN/GaN heterostructures grown by MOCVD and quantitatively investigate the effects of AlGaN buffers and the GaNchannel thickness on the electrical transport properties of these systems. Also, we obtain the most important effective parameters of the temperature-dependent mobility in the range 35–300 K. Our results show that inserting a 1.1 μm thick Al{sub 0.04}Ga{sub 0.96}N buffer enhances electron mobility by decreasing the effect of phonons, the interface roughness, and dislocation and crystal defect scattering mechanisms. Also, as the channel thickness increases from 20 nm to 40 nm, the electron mobility increases from 2200 to 2540 cm{sup 2}/(V s) and from 870 to 1000 cm{sup 2}/(V s) at 35 and 300 K respectively, which is attributed to the reduction in the dislocation density and the strain-induced field. Finally, the reported experimental data show that inserting a 450 nm graded AlGaN layer before an Al{sub 0.04}Ga{sub 0.96}N buffer causes a decrease in the electron mobility, which is attributed to the enhancement of the lateral size of roughness, the dislocation density, and the strain-induced field in this sample.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Stabilizing Ir(001) Epitaxy on Yttria-Stabilized Zirconia Using a Thin Ir Seed Layer Grown by Pulsed Laser Deposition

In this paper, we demonstrate the reproducible epitaxial growth of 100 nm thick Ir(001) films on a heteroepitaxial stack consisting of 5 nm Ir and 100 nm yttria-stabilized zirconia (YSZ) grown on Si(001) substrates. It is shown that a 5 nm thick Ir layer grown by pulsed laser deposition in the same chamber as the YSZ film without breaking the vacuum is the key to stabilizing Ir(001) epitaxial growth. Growth of the Ir seed layer with pure (001) orientation occurs only in a narrow growth temperature window from 550 to 750 °C, and the fraction of Ir(111) increases at substrate temperatures outside of this window. The Ir seed layer prevents exposure of the YSZ film to air during sample transfer and enables highly reproducible Ir(001) heteroepitaxy on YSZ buffered Si(001). In contrast, if Ir is grown directly on a bare YSZ layer that was exposed to ambient conditions, the films are prone to change orientation to (111). These results reveal that preserving the chemical and structural purity of the YSZ surface is imperative for achieving Ir(001) epitaxy. The narrow range of the mosaic spread values from eight experiments demonstrates the high yield and high reproducibility of Ir(001) heteroepitaxy by this approach. Lastly, the improved Ir(001) epitaxial growth method is of great significance for integrating a variety of technologically important materials such as diamond, graphene, and functional oxides on a Si platform.

36 MATERIALS SCIENCE↗

Operational constraints and strategies for systems to effect the sustainable, solar-driven reduction of atmospheric CO 2

The operational constraints for a 6-electron/6-proton CO 2 reduction system that operates at the concentration of CO 2 in the current atmosphere (p CO 2 = 400 ppm) have been evaluated on a variety of scale lengths that span from laboratory scale to global scale. Due to the low concentration of CO 2 in the atmosphere, limitations due to mass transport of CO 2 from the tropopause have been evaluated through five different regions, each with different characteristic length scales: the troposphere; the atmospheric boundary layer (ABL); the canopy layer; a membrane layer; and an aqueous electrolyte layer. The resulting CO 2 conductances, and associated physical transport limitations, will set the ultimate limit on the efficiency and areal requirements of a sustainable solar-driven CO 2 reduction system regardless of the activity or selectivity of catalysts for reduction of CO 2 at the molecular level. At the electrolyte/electrode interface, the steady-state limiting current density and the concomitant voltage loss associated with the CO 2 concentration overpotential in a one-dimensional solar-driven CO 2 reduction cell have been assessed quantitatively using a mathematical model that accounts for diffusion, migration and convective transport, as well as for bulk electrochemical reactions in the electrolyte. At p CO 2 = 400 ppm, the low diffusion coefficient combined with the low solubility of CO 2 in aqueous solutions constrains the steady-state limiting current density to <0.1 mA cm -2 in a typical electrochemical cell with natural convection and employing electrolytes with a range of pH values. Hence, in such a system, the CO 2 capture area must be 100- to 1000-fold larger than the solar photon collection area to enable a >10% efficient solar-driven CO 2 reduction system (based on the solar collection area). This flux limitation is consistent with estimates of oceanic CO 2 uptake fluxes that have been developed in conjunction with carbon-cycle analyses for use in coupled atmosphere/ocean general circulation models. Two strategies to improve the feasibility of obtaining efficient and sustainable CO 2 transport to a cathode surface at p CO 2 = 400 ppm are described and modeled quantitatively. The first strategy employs yet unknown catalysts, analogous to carbonic anhydrases, that dramatically accelerate the chemically enhanced CO 2 transport in the aqueous electrolyte layer by enhancing the acid–base reactions in a bicarbonate buffer system. The rapid interconversion from bicarbonate to CO 2 in the presence of such catalysts near the cathode surface would in principle yield significant increases in the steady-state limiting current density and allow for >10% solar-fuel operation at the cell level. The second strategy employs a thin-layer cell architecture to improve the diffusive transport of CO 2 by use of an ultrathin polymeric membrane electrolyte. Rapid equilibration of CO 2 at the gas/electrolyte interface, and significantly enhanced diffusive fluxes of CO 2 in electrolytes, are required to increase the steady-state limiting current density of such a system. This latter approach however only is feasible for gaseous products, because liquid products would coat the electrode and therefore thicken the hydrodynamic boundary layer and accordingly reduce the diffusive CO 2 flux to the electrode surface. Regardless of whether the limitations due to mass transport to the electrode surface are overcome on the laboratory scale, at global scales the ultimate CO 2 flux limitations will be dictated by mass transport considerations related to transport of atmospheric CO 2 to the boundary plane of the solar-driven reactor system. The transport of CO 2 across the troposphere/ABL interface, the ABL/canopy layer interface, and the canopy layer/electrolyte interface have therefore been assessed in this work, to provide upper bounds on the ultimate limits for the solar-to-fuel (STF) conversion efficiency for systems that are intended to effect the reduction of atmospheric CO 2 in a sustainable fashion at global scale.

54 ENVIRONMENTAL SCIENCES↗

Development of a Perfectly Matched Layer Technique for a Discontinuous-Galerkin Spectral-Element Method

The numerical simulation of many aerodynamic non-periodic flows of practical interest involves discretized computational domains that often must be artificially truncated. Appropriate boundary conditions are required at these truncated domain boundaries, and ideally, these boundary conditions should be perfectly "absorbing" or "nonreflecting" so that they do not contaminate the flow field in the interior of the domain. The proper specification of these boundaries is critical to the stability, accuracy, convergence, and quality of the numerical solution, and has been the topic of considerable research. The need for accurate boundary specification has been underscored in recent years with efforts to apply higher-fidelity methods (DNS, LES) in conjunction with high-order low-dissipation numerical schemes to realistic flow configurations. One of the most popular choices for specifying these boundaries is the characteristics-based boundary condition where the linearized flow field at the boundaries are decomposed into characteristic waves using either one-dimensional Riemann or other multi-dimensional Riemann approximations. The values of incoming characteristics are then suitably modified. The incoming characteristics are specified at the in flow boundaries, and at the out flow boundaries the variation of the incoming characteristic is zeroed out to ensure no reflection. This, however, makes the problem ill-posed requiring the use of an ad-hoc parameter to allow small reflections that make the solution stable. Generally speaking, such boundary conditions work reasonably well when the characteristic flow direction is normal to the boundary, but reflects spurious energy otherwise. An alternative to the characteristic-based boundary condition is to add additional "buffer" regions to the main computational domain near the artificial boundaries, and solve a different set of equations in the buffer region in order to minimize acoustic reflections. One approach that has been used involves modeling the pressure fluctuations as acoustic waves propagating in the far-field relative to a single noise-source inside the buffer region. This approach treats vorticity-induced pressure fluctuations the same as acoustic waves. Another popular approach, often referred to as the "sponge layer," attempts to dampen the flow perturbations by introducing artificial dissipation in the buffer region. Although the artificial dissipation removes all perturbations inside the sponge layer, incoming waves are still reflected from the interface boundary between the computational domain and the sponge layer. The effect of these refkections can be somewhat mitigated by appropriately selecting the artificial dissipation strength and the extent of the sponge layer. One of the most promising variants on the buffer region approach is the Perfectly Matched Layer (PML) technique. The PML technique mitigates spurious reflections from boundaries and interfaces by dampening the perturbation modes inside the buffer region such that their eigenfunctions remain unchanged. The technique was first developed by Berenger for application to problems involving electromagnetic wave propagation. It was later extended to the linearized Euler, Euler and Navier-Stokes equations by Hu and his coauthors. The PML technique ensures the no-reflection property for all waves, irrespective of incidence angle, wavelength, and propagation direction. Although the technique requires the solution of a set of auxiliary equations, the computational overhead is easily justified since it allows smaller domain sizes and can provide better accuracy, stability, and convergence of the numerical solution. In this paper, the PML technique is developed in the context of a high-order spectral-element Discontinuous Galerkin (DG) method. The technique is compared to other approaches to treating the in flow and out flow boundary, such as those based on using characteristic boundary conditions and sponge layers. The superiority of the current PML technique over other approaches is demonstrated for a range of test cases, viz., acoustic pulse propagation, convective vortex, shear layer flow, and low-pressure turbine cascade flow. The paper is structured as follows. We first derive the PML equations from the non{linear Euler equations. A short description of the higher-order DG method used is then described. Preliminary results for the four test cases considered are then presented and discussed. Details regarding current work that will be included in the final paper are also provided.

Spectral↗

Synthesis and electrical behavior of VO 2 thin films grown on SrRuO 3 electrode layers

VO 2 thin films were grown on conducting oxide underlayer SrRuO 3 buffered SrTiO 3 (111) and Si/SiO 2 substrates, respectively, using sputtering. X-ray diffraction phi-scans revealed the epitaxial nature of the VO 2 films grown on SrRuO 3 buffered SrTiO 3 and polycrystalline structure for films grown on SrRuO 3 buffered Si/SiO 2 . X-ray photoelectron spectroscopy confirms a dominant presence of V 4+ in both films and establishes a high-quality growth of single-phase VO 2 films. Temperature and electric-field driven metal-insulator-transition in both the in-plane and out-of-plane configurations were investigated. Depending on the configuration, the resistance change across the metal-insulator-transition varies from a factor of 1.57–3. The measured resistance in each state as well as the magnitude of resistance change were similar during temperature and electric-field driven metal-insulator-transition. To shed light on the suppressed metal-insulator-transition characteristics due to the current shunting effect from conducting SrRuO 3 bottom electrode, a distributed resistance network model is proposed and benchmarked against reports from the literature. Here, the results demonstrate the growth of high-quality VO 2 on conducting SrRuO 3 layers and their electrical behavior, which is of particular interest for all-oxide electronic devices utilizing phase transitions such as resistive memory and neuromorphic oscillators.

36 MATERIALS SCIENCE↗

Growth of ferroelectric Ba{sub 0.8}Sr{sub 0.2}TiO{sub 3} epitaxial films by ultraviolet pulsed laser irradiation of chemical solution derived precursor layers

Highly crystalline epitaxial Ba{sub 0.8}Sr{sub 0.2}TiO{sub 3} (BST) thin-films are grown on (001)-oriented LaNiO{sub 3}-buffered LaAlO{sub 3} substrates by pulsed laser irradiation of solution derived barium-zirconium-titanium precursor layers using a UV Nd:YAG laser source at atmospheric conditions. The structural analyses of the obtained films, studied by X-ray diffractometry and transmission electron microscopy, demonstrate that laser processing allows the growth of tens of nm-thick BST epitaxial films with crystalline structure similar to that of films obtained through conventional thermal annealing methods. However, the fast pulsed nature of the laser employed leads to crystallization kinetic evolution orders of magnitude faster than in thermal treatments. The combination of specific photothermal and photochemical mechanisms is the main responsible for the ultrafast epitaxial laser-induced crystallization. Piezoresponse microscopy measurements demonstrate equivalent ferroelectric behavior in laser and thermally annealed films, being the piezoelectric constant ∼25 pm V{sup −1}.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The epidermis of the pea epicotyl is not a unique target tissue for auxin-induced growth

Previous research has suggested that the epidermis of dicotyledonous stems is the primary site of auxin action in elongation growth. We show for pea (Pisum sativum L.) epicotyl sections that this hypothesis is incorrect. In buffer (pH 6.5), sections from which the outer cell layers were removed (peeled) elongated slowly and to the same extent as intact sections. Addition of 10 micromolar indoleacetic acid to this incubation medium caused peeled sections to grow to the same extent and with the same kinetics as auxin-treated nonpeeled sections. This indicates that both epidermis and cortical tissues have the ability to respond rapidly to auxin and that the epidermis is not the sole site of auxin action in dicotyledonous stems. Previous reports that peeled pea sections respond poorly to auxin may have resulted from an acid extension of these sections due to the use of distilled water as the incubation medium.

Non-NASA Center↗

Modeling Stress-Induced Pore Water Pressures in The Vadose Zone Beneath a Composite-Lined Landfill - 20029

A finite-element model was developed to evaluate mechanisms contributing to positive pore pressures measured with sealed pressure transducers in the geological buffer beneath the Environmental Management Waste Management Facility, a composite-lined mixed waste disposal facility operated by the US Department of Energy. The geological buffer is a 3-m-thick engineered fine-textured layer directly beneath the Environmental Management Waste Management Facility's composite liner, and above the groundwater table. The model accounts for changes in pore water pressure resulting from (i) loading imposed by waste placed on the overlying liner, (ii) moistening of the geological buffer due to equilibration with the underlying geological materials, and (iii) fluctuations in the elevation of the underlying groundwater table. Pore water pressures predicted by the model are in good agreement with pore water pressures measured in the field. The predictions confirm that positive pore water pressures recorded by the sealed pressure transducers in the geological buffer are excess pore water pressures induced by the vertical normal stress imposed by waste placed on the liner, and are not due to a rise in the groundwater table. Simulations also showed that two additional years of filling would further increase the pore water pressure without any change in elevation of the groundwater table. The geological buffer remained unsaturated during the simulation, with a B-coefficient (parameter indicative of the degree of saturation) similar to that computed from the field-measured pore water pressures and waste filling records. Larger increases in pore water pressure were observed when the geological buffer was assumed to have higher initial saturation, as was observed in the field data. Incorporating seasonal fluctuations in the groundwater table beneath the geological buffer in the model resulted in predictions of small seasonal oscillation in the pore water pressure at the measurement location, similar to seasonal oscillations observed in the field. Predictions made with the model indicate that the dissipation of the excess pore water pressures will occur over decades due to the low hydraulic conductivity of the geological buffer material. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗