Search NASA⌕ Search

SEARCH · Search NASA

Results for “height estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

A Non-Destructive Investigation of Plutonium Reference Items Used for Calibration

The calibration of Non-Destructive Assay (NDA) equipment relies on the availability of certified items of known content and construction. Increasing use is being made of calculational tools to create calibration data and so representative standards are no longer always needed. However, even with this approach it is invaluable to benchmark the tools against the measured response under well known conditions and to apply the Measured: Calculated ratio as a scaling factor. Reference sources for Pu are typically doubly encapsulated for safety reasons and contain Pu of well known chemical form, elemental composition, relative isotopic composition and mass. Destructive analysis techniques are used to characterize the materials and so these attributes are usually known with far greater accuracy than that achievable by the NDA methods to which they are being applied. Construction details are also usually provided in order to permit attenuation and related factors to be estimated. This work concerns the empirical investigation of a set of encapsulated PuO{sub 2} powder standards. The characterization and fabrication of the items is adequately documented with the exception of fill height. The fill height governs the powder density and in turn both the self attenuation of photons and the self multiplication of neutrons, consequently this is an important omission. Initially the location and dimensions of the internal plunger cup was used as a basis to estimate the packing density, but later records of plunger positions made at the time of filling were found and significant revisions followed. As a consequence of discrepancies observed in measurements designed to evaluate a new lump correction algorithm we were led to investigate the powder density and distribution directly by gamma-ray scanning. In some cases this resulted in revised density estimates. Equally importantly it was discovered that for the smallest mass items, the powder was not held fixed in the form of a uniform disc by the spring loaded plunger but rather could flow inside the inner capsule. In this paper we describe the nature of the investigation, report the salient findings and explain the implications for modeling the sources for the calibration of NDA equipment. (authors)

07 ISOTOPE AND RADIATION SOURCES↗

The application of forest classification from Landsat data as a basis for natural hydrocarbon emission estimation and photochemical oxidant model simulations in southeastern Virginia

The possible contribution by natural hydrocarbon emissions to the total ozone budget recorded in the Tidewater region of southeastern Virginia during the height of the summer period was examined. Natural sources investigated were limited to the primary HC emitters and most prevalent natural vegetation, the forests. Three types and their areal coverage were determined for Region VI of the Virginia State Air Pollution Control Board using remotely sensed data from Landsat, a NASA experimental earth resources satellite. Emission factors appropriate to the specific types (coniferous 0.24 x 10 to the 13th, mixed 0.63 x 10 to the 13th, deciduous 1.92 x 10 to the 13th, microgram/h), derived from contemporary procedures, were applied to produce an overall regional emission rate of 2.79 x 10 to the 13th microgram/h for natural non-methane hydrocarbons (NMHC). This rate was used with estimates of the anthropogenic NO(x) and NMHC loading, as input into a photochemical box model. Additional HC loading on the order of that estimated to be produced by the natural forest communities was required in order to reach certain measured summer peak ozone levels as the computer simulation was unable to account for the measured episodic levels on the basis of the anthropogenic inventory alone.

Salop, J.↗

Critical wind speeds suggest wind could be an important disturbance agent in Amazonian forests

Abstract Recent research in the central Amazon suggests that wind is a major agent of disturbance, however, a mechanistic understanding of how wind may lead to tree mortality in Amazonian forests remains unclear. Here we estimated wind speeds necessary to topple central Amazon trees by linking both static and dynamic versions of two wind speed estimation methods (four methods total) to field data on tree failure derived from a static winching study. Static versions of these methods assumed invariant wind characteristics as more trees failed, while dynamic versions updated tree spacing, leaf area index and wind profiles progressively after each tree failure. First, we used a profile method which estimates wind force on individual trees by segments. We calculated drag on each segment and converted drag into basal turning moment, and compared the summed turning moments to the critical turning moment measured in the winching study. Estimated critical wind speeds from the static profile method varied greatly, from 10.75 m s−1 to >120.0 m s−1 with a mean of 45.70 m s−1. Critical wind speeds estimated with static approaches decreased with tree size but were not significantly different between two focal genera. Primary drivers of variation in critical wind speed were tree height and crown size. Second, we used the turning moment coefficient method of Hale, S.E., Gardiner, B., Peace, A., Nicoll, B., Taylor, P. and Pizzirani, S. 2015 Comparison and validation of three versions of a forest wind risk model. Environ. Model. Softw.68, 27–41. doi:10.1016/j.envsoft.2015.01.016.; the static version of this method yielded less-variable estimates, ranging from 18.98 to 52.01 m s−1, with a mean of 30.88 m s−1. Notably, the two static methods for estimating critical wind speeds differed in the trees they identified as having the highest and lowest critical wind speeds. Dynamic variants of the above two methods produced greatly reduced ranges in CWS estimates for our study trees, because after the early tree failures, remaining trees were subject to greater wind penetration into the stand and thus greater loading for a given above-canopy wind speed. CWS estimated with dynamic approaches differed significantly between the focal taxa. Nevertheless, both estimates suggest that wind speeds commonly observed during Amazon storms are sufficient to produce widespread tree damage and mortality.

Peterson, Chris J.↗

Estimates of the geostrophic stream function in the western North Pacific from XBT surveys

Bernstein and White (1981) have argued that the 300 m temperature field in the western North Pacific reflects the 100/1000 dbar geostrophic stream function of the upper ocean where 100/1000 dbar implies the 100 dbar surface relative to the 1000 dbar surface. The correlation between upper ocean dynamic height and temperature in this region provides the basis for their argument. The involved relationship suggests that it may be possible to monitor the relative upper ocean geostrophic transport, as well as energy relations and heat fluxes with expendable bathythermograph (XBT) surveys. Certain discrepancies between data from different sources are felt to result from problems with the XBT observations. The present investigation is concerned with the determination of the ability of XBT surveys to estimate geostrophic currents, taking into account a comparison of directly measured data with estimated shears. Discrepancies are found to be related to an underestimation of the dynamic height gradients.

Koblinsky, C. J.↗

Collar Properties and Measurement Time Confer Minimal Bias Overall on Annual Soil Respiration Estimates in a Global Database

Abstract Measuring the soil‐to‐atmosphere carbon dioxide (CO 2 ) flux (soil respiration, R S ) is important to understanding terrestrial carbon balance and to forecasting climate change. Such measurements are frequently made using measurement collars permanently inserted into the soil surface. However, differences in measurement duration and frequency, as well as collar properties, may lead to biases in the estimation of annual R S . Using a newly updated global R S database (SRDB‐V5), we investigated the annual R S bias associated with five methodological factors: collar height, collar coverage area, collar insertion depth, measurement duration, and measurement frequency. We found that annual R S was negatively correlated with collar insertion depth, consistent with the idea that collar insertion cuts roots and thus reduces R S . Annual R S was also negatively related with collar height and collar coverage area, perhaps because uniform head‐space mixing is difficult to achieve in larger volume chambers; however, these effects were quantitatively small (bias of ~2% to 10% of mean R S ). We found no correlation of measurement duration or measurement frequency with annual R S . These findings suggest that variation in R S methodology generally introduces minimal bias overall. Therefore, compilations of minimally adjusted annual R S measurements provide a reliable resource for synthesis studies, global annual R S modeling, and investigation of how soil carbon responds to climate change.

Jian, Jinshi↗

Detection of a corona of fast oxygen atoms during solar maximum

A series of twilight interferometric observations of the near infrared O(+)(2P) doublets at 7320 and 7330 A between April 1979 and October 1979 detected excessive amounts of emission at shadow heights above 550 km. The scale height deduced from the vertical brightness profile determined from data taken on September 26, 1979, when the 10.7-cm flux was 231, showed a marked increase above 550 km. The equivalent temperature was estimated to be 4000 K or higher. Observations of the emission line shape with the high-resolution capability of the interferometer substantiated these results by a very apparent progressive broadening of the emission profile between times of low and high shadow height. It is concluded from these results that there exists an atomic oxygen corona overlying the thermosphere during the solar maximum period.

Yee, J. H.↗

Rhode Island Site - NREL ASSIST Thermodynamic Retrievals TROPoe v0.19 / Derived Data

This dataset contains daily files with thermodynamic profiles retrieved with the optimal estimation physical retrieval TROPoe v0.19 (Turner and Löhnert, 2014; Turner and Blumberg, 2019; Turner and Löhnert, 2021). The profiles are retrieved every 10 minutes from instantaneous observations from the NREL ASSIST-II (SN 12) infrared spectrometer. Observations are noise-filtered but not averaged in time to minimize errors due to non-uniform clouds. Additional input data in TROPoe are cloud base height from the collocated NREL upgraded Galion lidar (Newsom et al., 2019), and surface temperature, relative humidity, and pressure from the collocated PNNL met tower. The full pipeline to run the retrieval is available at https://github.com/StefanoWind/TROPoe_processor. In addition to these temporally resolved input data, TROPoe requires an a priori dataset (prior) that provides mean climatological estimates of thermodynamic profiles and specifies how temperature and humidity covary with height as an input (for details see, e.g., Djalalova et al., 2022). The prior is a key component of the retrieval and provides a constraint on the ill-posed inversion problem. A monthly prior was computed from operational radiosonde launches at Upton, NY.

17 WIND ENERGY↗

Validation of clear-sky fluxes for tropical oceans from the Earth Radiation Budget Experiment

The existence and magnitude of a systematic bias in the clear-sky longwave fluxes from the Earth Radiation Budget Experiment (ERBE) is investigated. The bias is apparently introduced because the ERBE method for scene identification does not account for large zonal gradients in longwave absorption by water vapor. The ERBE fluxes are compared to fluxes calculated with a radiative transfer model from ship radiosonde measurements. The comparison is based upon an analysis of 5 yr of coincident satellite and radiosonde observations for equatorial ocean regions. The differences between the ERBE and model fluxes are examined as functions of sea surface temperature (SST) and relative humidity. The authors use height-mean relative humidity bar-RH as an index of atmospheric moisture. The average offset between and model ERBE fluxes ranges between +2 and +6 W/sq m for SSTs above 295 K, and the gradients with respect to SST are nearly identical. However, the difference between the model and ERBE depends significantly on the tropospheric relative humidity. ERBE fluxes exceed model fluxes for bar-RH above 70%, and the maximum offset of +9 to +12 W/sq m is consistent with previous estimates. There are also indications that the clear-sky fluxes for bar-RH below 25% may be underestimated by about 10-15 W/sq m. Since extreme values of height-mean humidity are relatively infrequent, the net bias introduced in the ERBE monthly mean clear-sky fluxes is generally less than the systematic error in estimates introduced in the ERBE monthly mean clear-sky fluxes is generally less than the systematic error in estimates of the instantaneous fluxes. These findings support earlier work on the coupling between SST and the atmospheric greenhouse effect, in particular the existence of a super greenhouse effect for oceans warmer than 300 K. Recent reports of much larger systematic differences are not supported by this analysis. The results indicate that comparison of general circulation model (GCM) and ERBE clear-sky longwave fluxes will depend explicitly on atmospheric humidity.

Collins, W. D.↗

Assessment of Model Hub Height Wind Speed Performance Using DOE Lidar Buoy Data

As the offshore wind industry continues to gain momentum both in the U.S. and globally, reanalysis products remain essential tools for the lifecycle of a wind farm. From project siting and production estimates to determining construction and maintenance windows, reanalysis products play an important role. These regional and global long-term models also serve as inputs to higher resolution models. With such wide-ranging impacts on the offshore wind industry, the need for validation of reanalysis products is strong, particularly at typical turbine hub heights. Pacific Northwest National Laboratory (PNNL) operates two AXYS WindSentinelTM buoys for the U.S. Department of Energy (DOE) in order to collect meteorological and oceanographic data, including hub height wind speed, in areas of interest for offshore wind development. This work uses DOE buoy observations off the coasts of New Jersey and Virginia to evaluate the performance of Modern Era Retrospective Analysis for Research and Applications-2 (MERRA-2), the North American Regional Reanalysis (NARR), the European Center for Medium-Range Weather Forecasts (ECMWF) Reanalysis 5th generation (ERA5), and the National Oceanic and Atmospheric Administration (NOAA) assimilation system Rapid Refresh (RAP). Biases and degrees of correspondence are determined for each reanalysis product in order to provide insights on the performance and uncertainty for long-term wind resource characterization. With the baseline metrics determined, this work proceeds with an investigation into the sources of large deviations between the modeled and observed hub height wind speeds during the East Coast lidar buoy deployments. Consistent sources of reanalysis model error include stably stratified flow conditions, high wind shear, flow parallel to the coastline, and tropical and winter storms. For the near shore New Jersey location, offshore winds (i.e. blowing from land to water) tend to be associated with model overestimation of observed hub height wind speed, while winds parallel to the coastline are correlated with model underestimation of wind speed. Similarly, near the Virginia buoy, during southerly winds (parallel to the coastline) models underestimate the observed wind speed due to coastal upwelling. Reanalysis model wind speeds underestimate the hub height winds with increasing stable atmospheric stratification. Reanalysis model biases are seen when the observed wind speeds approach or exceed typical turbine cut-out speeds (around 20 m s-1). Large model errors during winter and tropical storm events, high wind speed events, and ramp events are often the result of wind speed timing and magnitude offsets. Overall, ERA5 provides the most successful representation of observed offshore hub height wind speeds at the U.S. East Coast buoy locations and is therefore best suited as an input boundary condition for model case studies. ERA5 performs well for a variety of atmospheric phenomena, including storms and sea breezes, however RAP, the next most successful reanalysis model, performs best in capturing the frequency of ramp events.

17 WIND ENERGY↗

Can We Infer Ocean Dynamics from Altimeter Wavenumber Spectra?

The wavenumber spectra of sea surface height (SSH) and kinetic energy (KE) have been used to infer the dynamics of the ocean. When quasi-geostrophic dynamics (QG) or surface quasi-geostrophic (SQG) turbulence dominate and an inertial subrange exists, a steep SSH wavenumber spectrum is expected with k-5 for QG turbulence and a flatter k-11/3 for SQG turbulence. However, inspection of the spectral slopes in the mesoscale band of 70 to 250 km shows that the altimeter wavenumber slopes typically are much flatter than the QG or SQG predictions over most of the ocean. Comparison of the altimeter wavenumber spectra with the spectra estimated from the output of an eddy resolving global ocean circulation model (the Hybrid Coordinate Ocean Model, HYCOM, at 1/25 resolution), which is forced by high frequency winds and includes the astronomical forcing of the sun and the moon, suggests that the flatter slopes of the altimeter may arise from three possible sources, the presence of internal waves, the lack of an inertial subrange in the 70 to 250 km band and noise or submesoscales at small scales. When the wavenumber spectra of SSH and KE are estimated near the internal tide generating regions, the resulting spectra are much flatter than the expectations of QG or SQG theory. If the height and velocity variability are separated into low frequency (periods greater than 2 days) and high frequency (periods less than a day), then a different pattern emerges with a relatively flat wavenumber spectrum at high frequency and a steeper wavenumber spectrum at low frequency. The stationary internal tides can be removed from the altimeter spectrum, which steepens the spectral slopes in the energetic internal wave regions. Away from generating regions where the internal waves

Richman, James↗

BLOC Site - ASSIST Thermodynamic retrievals TROPoe / Derived Data

This dataset contains daily files with thermodynamic profiles retrieved with the optimal estimation physical retrieval TROPoe (Turner and Löhnert 2014; Turner and Blumberg 2019; Turner and Löhnert 2021). The profiles are retrieved every 10 minutes from instantaneous radiances observed with an Atmospheric Sounder Spectrometer by Infrared Spectral Technology (ASSIST, Rochette et al. 2009) operated by NOAA Physical Sciences Laboratory on Block Island for WFIP3. The spectral bands used in the retrieval are in the wavenumber range from 612 - 905.4 cm-1 and are specified in Turner and Löhnert (2021). Radiances are noise-filtered but not averaged in time to minimize errors due to non-uniform clouds. Additional input data in TROPoe are cloud base height from a collocated ceilometer operated by NOAA GML and temperature, water vapor mixing ratio, and pressure from a sensor attached to the ASSIST housing. In addition to these temporally resolved input data, TROPoe requires an a priori dataset (prior) that provides mean climatological estimates of thermodynamic profiles and specifies how temperature and humidity covary with height as an input (for details see, e.g., Djalalova et al. 2022). The prior is a key component of the retrieval and provides a constraint on the ill-posed inversion problem. A monthly prior was computed from operational radiosonde launches at Upton, NY.

17 WIND ENERGY↗

A New Approach for Estimating Entrainment Rate in Cumulus Clouds

A new approach is presented to estimate entrainment rate in cumulus clouds. The new approach is directly derived from the definition of fractional entrainment rate and relates it to mixing fraction and the height above cloud base. The results derived from the new approach compare favorably with those obtained with a commonly used approach, and have smaller uncertainty. This new approach has several advantages: it eliminates the need for in-cloud measurements of temperature and water vapor content, which are often problematic in current aircraft observations; it has the potential for straightforwardly connecting the estimation of entrainment rate and the microphysical effects of entrainment-mixing processes; it also has the potential for developing a remote sensing technique to infer entrainment rate.

54 ENVIRONMENTAL SCIENCES↗

BLOC Site - ASSIST Thermodynamic Retrievals TROPoe v0.18 / Derived Data

This dataset contains daily files with thermodynamic profiles retrieved with the optimal estimation physical retrieval TROPoe (Turner and Löhnert 2014; Turner and Blumberg 2019; Turner and Löhnert 2021). This is a post-processed dataset and recommended for use. The profiles are retrieved every 10 minutes from instantaneous radiances observed with an Atmospheric Sounder Spectrometer by Infrared Spectral Technology (ASSIST, Michaud-Belleau et al. 2025) operated by NOAA Physical Sciences Laboratory (PSL) on Block Island for WFIP3. The spectral bands used in the retrieval are in the wavenumber range from 612 - 905.4 cm-1 and are specified in Turner and Löhnert (2021). Additional input data in TROPoe are cloud base height from a collocated ceilometer operated by NOAA GML and temperature, water vapor mixing ratio, and pressure from a collocated surface tower operated by NOAA PSL. In addition to these temporally resolved input data, TROPoe requires an a priori dataset (prior) that provides mean climatological estimates of thermodynamic profiles and specifies how temperature and humidity covary with height as an input (for details see, e.g., Djalalova et al. 2022). The prior is a key component of the retrieval and provides a constraint on the ill-posed inversion problem. A monthly prior was computed from operational radiosonde launches at Upton, NY. The TROPoe docker container (version 0.18) is available from Docker Hub at https://hub.docker.com/r/davidturner53/tropoe/tags, and the source code code is available in the GitHub repository https://github.com/OAR-atmospheric-observations/TROPoe.

17 WIND ENERGY↗

NANT Site - ASSIST Thermodynamic Retrievals TROPoe v0.18 / Derived Data

This dataset contains daily files with thermodynamic profiles retrieved with the optimal estimation physical retrieval TROPoe (Turner and Löhnert 2014; Turner and Blumberg 2019; Turner and Löhnert 2021). This is a post-processed dataset and recommended for use. The profiles are retrieved every 10 minutes from instantaneous radiances observed with an Atmospheric Sounder Spectrometer by Infrared Spectral Technology (ASSIST, Michaud-Belleau et al. 2025) operated by NOAA Physical Sciences Laboratory (PSL) on Nantucket Island for WFIP3. The spectral bands used in the retrieval are in the wavenumber range from 612 - 905.4 cm-1 and are specified in Turner and Löhnert (2021). Additional input data in TROPoe are cloud base height from a collocated ceilometer operated by NOAA GML and temperature, water vapor mixing ratio, and pressure from a collocated surface tower operated by NOAA PSL. In addition to these temporally resolved input data, TROPoe requires an a priori dataset (prior) that provides mean climatological estimates of thermodynamic profiles and specifies how temperature and humidity covary with height as an input (for details see, e.g., Djalalova et al. 2022). The prior is a key component of the retrieval and provides a constraint on the ill-posed inversion problem. A monthly prior was computed from operational radiosonde launches at Upton, NY. The TROPoe docker container (version 0.18) is available from Docker Hub at https://hub.docker.com/r/davidturner53/tropoe/tags, and the source code code is available in the GitHub repository https://github.com/OAR-atmospheric-observations/TROPoe.

17 WIND ENERGY↗

Estimates of Radioxenon Released from Southern Hemisphere Medical isotope Production Facilities Using Measured Air Concentrations and Atmospheric Transport Modeling

Abstract The International Monitoring System (IMS) of the Comprehensive-Nuclear-Test-Ban-Treaty monitors the atmosphere for radioactive xenon leaking from underground nuclear explosions. Emissions from medical isotope production represent a challenging background signal when determining whether measured radioxenon in the atmosphere is associated with a nuclear explosion prohibited by the treaty. The Australian Nuclear Science and Technology Organisation (ANSTO) operates a reactor and medical isotope production facility in Lucas Heights, Australia. This study uses two years of release data from the ANSTO medical isotope production facility and Xe-133 data from three IMS sampling locations to estimate the annual releases of Xe-133 from medical isotope production facilities in Argentina, South Africa, and Indonesia. Atmospheric dilution factors derived from a global atmospheric transport model were used in an optimization scheme to estimate annual release values by facility. The annual releases of about 6.8×1014 Bq from the ANSTO medical isotope production facility are in good agreement with the sampled concentrations at these three IMS sampling locations. Annual release estimates for the facility in South Africa vary from 1.2×1016 to 2.5×1016 Bq and estimates for the facility in Indonesia vary from 6.1×1013 to 3.6×1014 Bq. Although some releases from the facility in Argentina may reach these IMS sampling locations, the solution to the objective function is insensitive to the magnitude of those releases.

07 ISOTOPE AND RADIATION SOURCES↗

Rate constants in spatially inhomogeneous systems

Here, we introduce a theory and accompanying importance sampling method for computing rate constants in spatially inhomogeneous systems. Using the relationship between rate constants and path space partition functions, we illustrate that the relative change in the rate of a rare event through space is isomorphic to the calculation of a free energy difference, albeit in a trajectory ensemble. Like equilibrium free energies, relative rate constants can be estimated by importance sampling. An extension to transition path sampling is proposed that combines biased path ensembles and weighted histogram analysis to accomplish this estimate. We demonstrate that rate constants can also be decomposed into different contributions, including relative changes in stability, barrier height, and flux. This decomposition provides a means of interpretation and insight into rare processes in complex environments. We confirm these ideas with a simple model of diffusion with spatially varying diffusivity and illustrate their utility in a model of ion pair dissociation near an electrochemical interface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Superresolution effect on a microstep phase image in a laser heterodyne microscope

The possibility of achieving superresolution on a microstep phase image in a laser scanning differential heterodyne microscope is studied both heoretically and experimentally. The superresolution is estimated as the width ratio for the amplitude and phase components of the microscope response measured at half the height of the corresponding parts of the response. It is shown theoretically that superresolution greatly exceeding unity can be achieved for an object in the form of a phase microstep introducing a phase shift equal to π. Superresolution of ∼2 is experimentally obtained for certified test micro-objects. A possibility of tuning a test sample into the superresolution regime by shifting a point photodetector in the microscope’s Fourier plane is demonstrated. (laser microscope)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

MAGNETIC ENERGY PARTITION BETWEEN THE CORONAL MASS EJECTION AND FLARE FROM AR 11283

On 2011 September 6, an X-class flare and a halo coronal mass ejection (CME) were observed from Earth erupting from the same active region AR 11283. The magnetic energy partition between them has been investigated. SDO/HMI vector magnetograms were used to obtain the coronal magnetic field using the nonlinear force-free field (NLFFF) extrapolation method. The free magnetic energies before and after the flare were calculated to estimate the released energy available to power the flare and the CME. For the flare energetics, thermal and nonthermal energies were derived using the RHESSI and GOES data. To obtain the radiative output, SDO/EVE data in the 0.1-37 nm waveband were utilized. We have reconstructed the three-dimensional (3D) periphery of the CME from the coronagraph images observed by STEREO-A, B, and SOHO. The mass calculations were then based on a more precise Thomson-scattering geometry. The subsequent estimate of the kinetic and potential energies of the CME took advantage of the more accurate mass, and the height and speed in a 3D frame. The released free magnetic energy resulting from the NLFFF model is about 6.4 Multiplication-Sign 10{sup 31} erg, which has a possible upper limit of 1.8 Multiplication-Sign 10{sup 32} erg. The thermal and nonthermal energies are lower than the radiative output of 2.2 Multiplication-Sign 10{sup 31} erg from SDO/EVE for this event. The total radiation covering the whole solar spectrum is probably a few times larger. The sum of the kinetic and potential energy of the CME could go up to 6.5 Multiplication-Sign 10{sup 31} erg. Therefore, the free energy is able to power the flare and the CME in AR 11283. Within the uncertainty, the flare and the CME may consume a similar amount of free energy.

79 ASTRONOMY AND ASTROPHYSICS↗