Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Analysis of Base Metal Microstructures and Mechanical Properties of a Single-Piece, Spin-Formed Forward Pressure Vessel Bulkhead

In 2012, a pathfinder forward pressure vessel bulkhead (FPVBH) for the Orion Multi-Purpose Crew Vehicle (MPCV) was fabricated using aluminum (Al) alloy 2219. The demonstration article was offered as a replacement for the baseline configuration, which at that time was a multi-piece welded construction using aluminum-lithium (Al-Li) alloy 2195. In 2014, the NASA Engineering and Safety Center (NESC) funded a Phase I effort to explore spin-forming as a manufacturing method to produce a complex-shaped, single-piece FPVBH for the crew module (CM) [1]. The primary focus of the NESC effort was to expand spin-forming technology to the fabrication of an Al-Li 2195 FPVBH. As a result, limited testing and analysis was performed on the original Al 2219 article. In this study, a sufficiently large plate of Al 2219 was not available for the fabrication of a FPVBH. Therefore, the forming blank comprised two plates (from different lots) butt welded together using a single friction stir weld. The welded forming blank was then spin formed into the FPVBH configuration and heat treated to the T62 temper. Mechanical property testing of the spin-formed 2219-T62 FPVBH revealed that the tensile properties were comparable to the Metallic Material Properties Development and Standardization (MMPDS) A-basis allowable for Al 2219-T6 wrought products. However, post-spin forming application of the standard heat treatment produced large, recrystallized grains in the material. The response varied within the two plates; one plate lot exhibited nearly complete recrystallization, while the other lot contained bands of recrystallization. Although no reduction in tensile properties was observed due to these microstructural variations, a more detailed investigation was recommended to better understand the effect of spin forming on the recrystallization mechanism and the impact on other material properties. The current study examined the microstructure and mechanical properties of the fully processed Al 2219-T62 FPVBH with emphasis on comparing differences between the two plates. Testing was limited to the cone region of the FPVBH. The two specific tasks in this study were: a) Characterization of the microstructure and mechanical properties in the two plates used in the FPVBH. b) Isolation of the impact of each step in the thermo-mechanical processing (TMP) sequence of the FPVBH on recrystallization and grain growth. Mechanical property testing sampled regions containing both large, recrystallized and small, unrecrystallized grains. Tensile strengths and elongations were equivalent in both regions and exceeded MMPDS A-basis allowables. Fracture toughness was equivalent in both regions and fracture morphology was typical of aluminum alloys. The fatigue precrack region of the fracture toughness specimens appeared more faceted in the recrystallized plate. This suggests that property testing that is more sensitive to grain size, such as fatigue crack growth rate and stress corrosion cracking, may be warranted. Alcoa reviewed the production records for the two plate lots and confirmed that composition of both plates was within the allowable range for Al 2219 and that plate processing steps were all performed within production limits. However, the Fe content was notably higher in the fully recrystallized plate, resulting in a greater volume fraction of large Fe-bearing inclusions and Al-Cu constituent particles. Alcoa did not provide details regarding plate processing variables for the two plate lots. It was surmised that deformation by hot rolling was the most accurate TMP simulation of commercial spin forming within a laboratory setting. Both hot rolling and spin forming comprise combinations of shear and compressive deformation. The through-thickness strain caused by hot rolling is symmetrical about the mid-plane, as the rollers contact both sides of the material. Shear strains are maximum at the inner and outer surfaces and trend toward zero at the mid-thickness. In contrast, spin forming utilizes a single roller on the outer surface, producing a gradient in shear stress through the thickness. Shear strains in spin-formed material are highest at the outer surface due to direct contact with the roller, and trend toward zero at the inner surface. Consequently, there will undoubtedly be some discrepancies in the mechanical response of hot-rolled and spin-formed products in the through-thickness direction. Interrupted TMP simulations were performed on remnant plate from the FPVBH forming blank in order to isolate the effects of a post-weld anneal, spin-forming deformation/thermal cycling, and solution heat treatment (SHT) on development of the recrystallized microstructures. Analysis confirmed that large, recrystallized grains formed exclusively during SHT and only after a certain deformation level was exceeded. Remnant plate from both lots that received thermal processing only did not exhibit recrystallization but exhibited fully recrystallized microstructures when processed by hot rolling. This indicates that (1) the level of deformation exceeded the critical level for recrystallization in both plates and (2) that the level of deformation during hot rolling was greater than that which accumulated during spin forming of the FPVBH. Comparison of the hot-rolled plate with the spin-formed material showed that the recrystallized grain size was larger in the FPVBH, providing further evidence that deformation levels were lower in the FPVBH. The most plausible explanation for the differing degrees of recrystallization in the two plates is particle stimulated nucleation (PSN) at the Fe-bearing inclusions and large Al-Cu constituent particles. In the plate with higher solute content, the greater volume fraction of these particles reduces the deformation level required to promote recrystallization. During spin forming the critical deformation level was likely exceeded for the higher Fe content plate resulting in a fully recrystallized microstructure. The lower Fe content plate developed a microstructure that exhibited bands of recrystallization due to the combination of a non-uniform distribution of particles and deformation. The critical deformation required for recrystallization was likely only exceeded during spin forming in regions of higher particle content. While there were differences in Fe content between these lots of Al 2219 plate, the composition of both was within defined alloy limits and Alcoa reported no anomalies during plate production. The observed differences in recrystallization after spin forming may reflect the inherent variability between these two lots of plate. The spin-forming vendor, Spincraft, reported that similar variations in recrystallized microstructures have been observed during examination of multiple spin-forming trials of a different 2xxx series aluminum alloy. Hence, tighter chemical specification limits on impurity levels in Al 2219 plate may help ensure uniform, predictable microstructures. Finally, the tensile and fracture toughness properties were not affected by the microstructural variations noted.

single-piece↗

Additively Manufactured Low Cost Upper Stage Combustion Chamber

Over the past two years NASA's Low Cost Upper Stage Propulsion (LCUSP) project has developed Additive Manufacturing (AM) technologies and design tools aimed at reducing the costs and manufacturing time of regeneratively cooled rocket engine components. High pressure/high temperature combustion chambers and nozzles must be regeneratively cooled to survive their operating environment, causing their design fabrication to be costly and time consuming due to the number of individual steps and different processes required. Under LCUSP, AM technologies in Sintered Laser Melting (SLM) GRCop-84 and Electron Beam Freeform Fabrication (EBF3) Inconel 625 have been significantly advanced, allowing the team to successfully fabricate a 25k-class regenerative chamber. Estimates of the costs and schedule of future builds indicate cost reductions and significant schedule reductions will be enabled by this technology. Characterization of the microstructural and mechanical properties of the SLM-produced GRCop-84, EBF3 Inconel 625 and the interface layer between the two has been performed and indicates the properties will meet the design requirements. The LCUSP chamber is to be tested with a previously demonstrated SLM injector in order to advance the Technology Readiness Level (TRL) and demonstrate the capability of the application of these processes. NASA is advancing these technologies to reduce cost and schedule for future engine applications and commercial needs.

Protz, Christopher↗

Mechanisms of paint bake response in resistance spot-welded first and third generation AHSS

Implementation of 3rd generation advanced high strength steels (3GAHSS) in automotive structures requires careful consideration of joining process implications. Due to the presence of increased carbon equivalent in 3GAHSS such as 980 HF relative to commonly-applied 1st generation AHSS such as 980 DP, the resultant properties of the weld nugget and heat affected zones in resistance spot welded must be engineered to provide consistent and acceptable performance, specifically in cross-tension loading mode. Although the as-welded cross-tension strength (CTS) of 980 HF is less than 980 DP, there is a significant improvement of the CTS after paint baking in 980 HF welds. 980 DP steel welds do not exhibit such marked improvement upon baking. The mechanism of the strong and beneficial effect of paint baking on 980 HF in comparison to 980 DP is discussed in light of its effect on residual stress distributions and microstructures. Although residual stress (strain) reduction is observed via synchrotron x-ray diffraction for all tested steels, this effect is demonstrated as secondary to the performance restoration of the weld joint in cross tension. High-resolution electron channeling contrast imaging (ECCI) micrographs reveal that paint baking affects a more beneficial degree of martensite tempering in 980 HF as compared to 980 DP. The martensite tempering is also evidenced by both a reduction in nano-hardness of critical microstructural features and re-emergence of ductile fracture behavior following the paint baking process. The tempering of martensite is concluded to be the dominant mechanism in improving cross tension strength of 3GAHSS welds following paint baking.

36 MATERIALS SCIENCE↗

A Machine Learning Approach to Quantitative Analysis of Enamel Microstructure from Scanning Electron Microscopy Images

Dental enamel, the outermost tissue of mammalian teeth, must withstand a lifetime of wear and cyclic contact. To meet this demand, enamel possesses a combination of high hardness and resistance to fracture, properties that are typically mutually exclusive. The impressive damage tolerance has been attributed largely to decussation of the enamel rods, the principal unit of its microstructure. As such, enamel is inspiring the design of next‐generation structural materials. However, quantitative descriptions of the decussated enamel rod microstructure remain limited due to challenges encountered in applying computed tomography and in acquiring quality images appropriate for traditional digital processing methods. Here, a machine learning segmentation method is applied to images of the enamel obtained using scanning electron microscopy to support quantitative analysis of the microstructure. A pretrained convolutional neural network is used to expand the input training image dataset to allow the training of a random forest classifier, which ultimately segments the image with a very small training set ( n = 3 images). A validation of this segmentation method is presented, in addition to its application to calculate relevant microstructural parameters for images of tooth enamel from selected mammalian species. The methodology applied here is equally applicable to other hard tissues.

36 MATERIALS SCIENCE↗

A mean field homogenization model for the mechanical response of ceramic matrix composites

SiC/SiC composites offer exceptional mechanical stability at high temperatures and under irradiation. These ceramic matrix composites are therefore strong candidate materials for future nuclear energy applications. Their mechanical response, which exhibits pseudo-plasticity, is mediated by matrix cracking, fiber debonding, and fiber pull-out due to slip. Here, this study introduces a mechanistic model for the behavior of unidirectionally reinforced SiC/SiC composites. Specifically a mean field homogenization approach is proposed to account for all deformation and degradation modes during mechanical deformation. The homogenization scheme relies on a Mori Tanaka method that is extended to consider the effects of the coating’s elasto-plastic response on the development of micromechanical fields. Further, the model proposed introduces a method to effectively account for the role of localized damage (i.e., cracks) on mechanical fields within both the fiber and the matrix. Upon validating the model against experimental data, the roles of interface sliding, coating dimensions and intrinsic elastic response, as well as of microstructure (e.g. porosity, fiber volume fraction) are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

An Eulerian crystal plasticity framework for modeling large anisotropic deformations in energetic materials under shocks

Here, this paper demonstrates a novel Eulerian computational framework for modeling anisotropic elastoplastic deformations of organic crystalline energetic materials (EM) under shocks. While Eulerian formulations are advantageous for handling large deformations, constitutive laws in such formulations have been limited to isotropic elastoplastic models, which may not fully capture the shock response of crystalline EM. The present Eulerian framework for high-strain rates, large deformation material dynamics of EM incorporates anisotropic isochoric elasticity via a hypo-elastic constitutive law and visco-plastic single-crystal models. The calculations are validated against atomistic calculations and experimental data and benchmarked against Lagrangian (finite element) crystal plasticity computations for shock-propagation in a monoclinic organic crystal, octahydro-1,3,5,7-tetranitro-1,3,5,7 tetrazocine (β-HMX). The Cauchy stress components and the resolved shear stresses calculated using the present Eulerian approach are shown to be in good agreement with the Lagrangian computations for different crystal orientations. The Eulerian framework is then used for computations of shock-induced inert void collapse in β-HMX to study the effects of crystal orientations on hotspot formation under different loading intensities. The computations show that the hotspot temperature distributions and the collapse profiles are sensitive to the crystal orientations at lower impact velocities (viz., 500 m/s); when the impact velocity is increased to 1000 m/s, the collapse is predominantly hydrodynamic and the role of anisotropy is modest. The present methodology will be useful to simulate energy localization in shocked porous energetic material microstructures and other situations where large deformations of single and polycrystals govern the thermomechanical response.

42 ENGINEERING↗

Asphaltene-induced spontaneous emulsification: Effects of interfacial co-adsorption and viscoelasticity

Asphaltenes are a class of high molecular weight aromatic compounds found in crude oil. They adsorb onto toluene-water interfaces and induce a spontaneous emulsification phenomenon, whereby stable water-in-oil emulsions form without the need of an external energy input. This work aims to control and understand the factors affecting spontaneous droplet formation in the presence of asphaltene adsorption. This is particularly useful for crude oil refining, where the presence of a stable emulsion hampers the efficiency of downstream processing operations. We explore the effect of the addition of copolymers designed as crude oil flow improvers as a means to control the extent of emulsion formation. We find that the polymers competitively adsorb onto the toluene-water interface and diminish spontaneous emulsification. Additionally, we conduct fluorescence microscopy experiments and measurements of the interfacial energy to determine the mechanism of spontaneous emulsification in asphaltene systems. We conclude that an emulsion forms via the diffusion of molecular water into the oil phase and subsequent binding with asphaltene aggregates, leading to the nucleation of micrometer-sized water droplets. We find that the polymer forms complexes with the dissolved asphaltenes, possibly hampering the ability of diffused water to bind to the asphaltenes and reducing the extent of spontaneous emulsification. Finally, we investigate the role of interfacial shear and dilatational viscoelasticity to better understand which fundamental interfacial properties are important in the emulsification of asphaltene-laden systems. We find that the rate of formation of an interfacial microstructural network is inversely correlated with the extent and rate of spontaneous emulsification.

42 ENGINEERING↗

Fatigue Performance of High-Strength Pipeline Steels and Their Welds in Hydrogen Gas Service

Objectives of the project include: Enable the use of high strength steel hydrogen pipelines, as significant cost savings can result by implementing high strength steels as compared to lower strength pipes. Demonstrate that girth welds in high-strength steel pipe exhibit fatigue performance similar to lower-strength steels in high-pressure hydrogen gas. Identify pathways for developing high-strength pipeline steels by establishing the relationship between microstructure constituents and hydrogen-accelerated fatigue crack growth (HA-FCG)

08 HYDROGEN↗

Microstructure and Mechanical Performance of the Friction Stir Welds Made on Neutron-Irradiated Steel with Helium

This report describes new experimental results on the microstructure and mechanical performance of the friction stir welds made on neutron-irradiated steel with helium. The report focuses on helium-related issues, specifically, helium-induced degradation in the welded joint, aiming to repair irradiated components of nuclear power plants (NPPs). The friction stir welds analyzed here were produced at Oak Ridge National Laboratory previously, and limited characterization work was performed, mostly addressing the presence or absence of macroscopic cracks. The present work attempts to perform a more comprehensive study to assess microstructure conditions, grain size, plastic strain gradients, the morphology of the helium-induced damage, and deformation behavior.

42 ENGINEERING↗

Multiscale analysis in solids with unseparated scales: fine-scale recovery, error estimation, and coarse-scale adaptivity

There are several engineering applications in which the assumptions of homogenization and scale separation may be violated, in particular, for metallic structures constructed through additive manufacturing. Instead of resorting to direct numerical simulation of the macroscale system with an embedded fine scale, an alternative approach is to use an approximate macroscale constitutive model, but then estimate the model-form error using a posteriori error estimation techniques and subsequently adapt the macroscale model to reduce the error for a given boundary value problem and quantity of interest. Here, we investigate this approach to multiscale analysis in solids with unseparated scales using the example of an additively manufactured metallic structure consisting of a polycrystalline microstructure that is neither periodic nor statistically homogeneous. As a first step to the general nonlinear case, we focus here on linear elasticity in which each grain within the polycrystal is linear elastic but anisotropic.

42 ENGINEERING↗

Effect of Heat Treatment on Microstructure and Mechanical Property of 316L Stainless Steel Produced by Laser Powder Bed Fusion

The advanced non-light water reactor designs (Gen IV reactors), including molten salt/ very high temperature/ sodium-cooled and lead-cooled fast reactors, typically operate at higher temperatures and more extreme radiation conditions than light water reactors. An intrinsic part of the deployment and progress of Gen IV reactor designs is selecting the most suitable structural material for a specific application. Additive manufacturing (AM), a fairly new process of making physical, three-dimensional objects from a computer design file, is going to completely change the way of design, build and certify nuclear systems. It offers a range of opportunities to produce complex geometries from existing materials, offers new routes for processing of previously difficult to process materials, allows for design of new high-performance materials, and finally facilitates hybridization of dissimilar materials. This emerging technology has successfully produced cars, wind turbine blade molds and even live cells. It could also open up big opportunities for the nuclear industry to quickly deploy technologies at a fraction of the cost. So far, AM techniques have been preliminarily applied in the field of nuclear reactors, including the classical parts such as the pressure vessel of a small reactor with 508-III steel, the bottom nozzle of a fuel assembly with 304L steel, the fuel cladding with zirconium alloy and the integrated impeller of a pump and the multi-channel valve body with 316L steel [6,7]. The AM applications for operating nuclear reactors started in auxiliary plant components and have slowly migrated to metallic reactors and core components, but many of these are not safety critical components. Although many parts used for nuclear reactors have been fabricated by AM techniques, practical applications in engineering are still a long way off due to the uncertainty factors focused on the processing, material properties, analysis methods and application standards, which feeds the safety and life-cycle of the nuclear reactor. Due to rapid, repeated heating and cooling during production, a high dislocation density was present in the AM material. This microstructure feature is unstable at elevated temperature while high temperature is one of the typical operation environments for nuclear reactors. Thus, it is important to understand the thermal effect on the microstructure of AM material. The objectives of this study are to investigate the effect of heat treatment on the microstructure and mechanical properties of 316L stainless steel produced by laser powder bed fusion additive manufacturing, and to determine an appropriate heat treatment practice that will be applied to the lightweight AM lattice-structured material with the same chemistry. The heat treatment study consisted of annealing the samples at a temperature range of 800 to 1200 oC with a 50 oC increment for different times (1-24 hours), followed by vacuum or air cooling. Microstructural characterization was carried out by Scanning Electron Microscope (SEM). Grain size and crystallographic orientation were investigated by Electron Backscatter Diffraction (EBSD). Vickers hardness tests with a 0.5 kg load were employed to determine the hardness of samples after different heat treatments. After heat treatment, the random crystallographic orientation was preserved, and the volume fraction of high-angle grain boundaries (grain boundary misorientation =15 oC) remained the same. The dislocation density decreased with annealing temperature due to recovery. The fine subgrain structures in the as-printed specimen were quite stable up to 1200 oC. Minimal recrystallization was observed up to 1200 oC. Recrystallization initiated only after 8.5 hours at 1200 oC. The SEM images did not show obvious dependence of microstructure on cooling rate. The hardness of the specimens decreased with increasing annealing temperature as a result of the decrease in dislocation density. It is interesting to note that the AM material showed very similar hardness to the wrought material when annealing at similar temperature, although the microstructures are very different. Annealing at 1050 oC for 1 hour followed by air cooling was selected as the heat treatment procedure for the lattice designed lightweight AM 316L material.

36 MATERIALS SCIENCE↗

Draft of M2 Report on Integration of the Hybrid Hydride Model into INL's MBM Framework for Review

This report documents the development, demonstration and validation of a mesoscale, microstructural evolution model for simulation of zirconium hydride {delta}-ZrH{sub 1.5} precipitation in the cladding of used nuclear fuels that may occur during long-term dry storage. While the Zr-based claddings are manufactured free of any hydrogen, they absorb hydrogen during service, in the reactor by a process commonly termed ‘hydrogen pick-up’. The precipitation and growth of zirconium hydrides during dry storage is one of the most likely fuel rod integrity failure mechanisms either by embrittlement or delayed hydride cracking of the cladding. While the phenomenon is well documented and identified as a potential key failure mechanism during long-term dry storage (NUREG/CR-7116), the ability to actually predict the formation of hydrides is poor. The model being documented in this work is a computational capability for the prediction of hydride formation in different claddings of used nuclear fuels. This work supports the Used Fuel Disposition Research and Development Campaign in assessing the structural engineering performance of the cladding during and after long-term dry storage. This document demonstrates a basic hydride precipitation model that is built on a recently developed hybrid Potts-phase field model that combines elements of Potts-Monte Carlo and the phase-field models. The model capabilities are demonstrated along with the incorporation of the starting microstructure, thermodynamics of the Zr-H system and the hydride formation mechanism.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural Evolution and Mechanical Properties of LP-DED NASA HR-1 – A Hydrogen Resistant AM Superalloy for Space Propulsion Applications

The National Aeronautics and Space Administration (NASA) has actively pursued metal additive manufacturing (AM) technologies for spaceflight applications since the late 2000s. AM offers transformative advantages in cost, schedule, part consolidation, and design flexibility. Among the various AM techniques, laser powder directed energy deposition (LP-DED) is particularly well suited for fabricating complex geometries with fine feature resolution. In propulsion systems that utilize high-pressure gaseous hydrogen—such as liquid hydrogen rocket engines—hydrogen environment embrittlement (HEE) presents a serious threat to material performance 1,2 . Mechanical property degradation under these conditions can compromise component reliability, especially under cyclic loading. To address this challenge, NASA developed NASA HR-1 (Hydrogen Resistant-1) as a solution for liquid rocket engine components operating in hydrogen-rich environments, using the LP-DED technique 3-9 . A key component in a liquid rocket engine is the exhaust nozzle, which is typically regeneratively cooled (regen) due to the high heat flux. NASA HR-1 was specifically developed for regen nozzle applications using hydrogen as a propellant, providing resistance to HEE, a critical issue for many materials. The AM version of NASA HR-1 was also formulated to achieve high ultimate tensile strength, along with high yield strength and ductility in this environment 5,6 . Low-cycle fatigue (LCF) is another important consideration in nozzle design, as components are expected to endure multiple starts and missions. Additionally, the LP-DED version of the alloy exhibits improved thermal conductivity compared to its wrought counterpart, which benefits nozzle cooling. Overall, NASA HR-1 offers an excellent balance of high strength, HEE resistance, LCF performance, thermal conductivity, and ductility to meet the demanding requirements of channel-cooled nozzles and other components used with hydrogen and other propellants. The LP-DED–processed NASA HR-1 requires several post-processing heat treatment steps to achieve the material properties desirable for its intended application 6 . These steps include stress relief, homogenization, solution annealing, and aging for precipitation hardening. The stress relief treatment mitigates residual stresses accumulated during the LP-DED process and minimizes the potential for distortion. Homogenization, a common step for AM materials, reduces elemental segregation and promotes recrystallization to develop a more equiaxed grain structure. The subsequent solution annealing treatment heats the part to a solid solution temperature to dissolve the undesirable η-phase that forms during cooling from homogenization, followed by rapid cooling to retain an η-phase–free microstructure. Finally, aging promotes precipitation of the strengthening γ′ phase in the alloy. The integration of compositional design and optimized thermal processing enables high-quality LP-DED NASA HR-1 components with excellent microstructural and mechanical stability. Improved chemical and microstructure homogeneity enhances ductility and fatigue resistance—both critical for safe and reliable operation in high-pressure hydrogen environments. NASA has successfully fabricated and hot-fire tested multiple subscale and full-scale channel wall nozzles using LP-DED NASA HR-1 5,6, 9-14 . These efforts included process refinements to support thin-wall construction and various channel geometries. Throughout development, several key observations emerged. After homogenization, the as-built columnar grain structure transforms into a fully equiaxed microstructure. However, subsequent treatments—such as solution annealing and aging—result in changes that are more difficult to track. The grain structure remains largely unchanged, and the γ′ precipitates, typically 5–10 nm in diameter, are beyond the resolution of scanning electron microscopy (SEM). While transmission electron microscopy (TEM) can resolve these fine precipitates, TEM sample preparation is time-consuming and difficult for LP-DED material. As an alternative, differential scanning calorimetry (DSC) offers a useful, qualitative approach to monitor precipitate evolution throughout different stages of heat treatment. The overall goal is to improve the understanding of how heat treatment affects the microstructure and mechanical performance of LP-DED NASA HR-1. This paper presents heat treatment design considerations, microstructural characterization, mechanical testing – including tensile and LCF testing in both air and hydrogen environments.

Superalloy↗

Achieving strength-ductility synergy in hierarchical aluminum metal matrix composites via friction extrusion

We report the fabrication of aluminum metal matrix composites (Al-MMCs) with hierarchical architectures via friction extrusion (FE), a scalable, single-step, solid-phase processing technique. Precursor pucks containing 0–15 vol% Al₂O₃ particles were extruded into fully dense AA6061-based composite rods. The FE induced a tree-ring-like architecture of concentric particle-rich and particle-lean bands, yielding refined grains in particle-rich regions and coarser grains elsewhere. At the nanoscale, magnesium in AA6061 selectively reacted with Al₂O₃ particles to form virus-like nodes, improving particle–matrix bonding. This multi-scale design strategy, combining mesoscale architecture, microscale grain refinement, and nanoscale interface engineering overcome the conventional strength–ductility trade-off. Tensile testing showed substantial increases in yield and ultimate tensile strengths while retaining high ductility ( > 20%). Enhanced strain hardening, driven by the accumulation of geometrically necessary dislocations at interfaces, contributed to the performance. The hierarchical microstructure produced by FE demonstrates a promising pathway for scalable fabrication of lightweight MMCs for structural applications requiring a combined high strength and ductility.

Kalsar, Rajib [Pacific Northwest National Laborato↗

Direct Measurements of Ionic Transport Behavior of Dual-Layer Porous Electrodes

To improve power and cycling performance of lithium-ion batteries, dual-layer or porosity-gradient electrodes have been proposed. By engineering a higher porosity close to the separator, the intention is to improve ion transport where it is most impactful. In this research, MacMullin numbers of two dual-layer anode samples are tested using an impedance measurement technique developed previously. To characterize the microstructure of each layer independently, we developed an improved transmission-line model that accounts for each layer's properties.Virtual experiments using COMSOL Multiphysics to simulate impedance measurements are used to examine and improve the accuracy of the numerical inversion procedure. The results for the two dual-layer anodes studied show that MacMullin numbers follow expected trends, though the anodes are quite different from each other.

Dual-Layer Electrodes↗

Laser Powder Bed Fusion Microstructure Surrogate Model

SAND2025-11467O The Laser Powder Bed Fusion (LPBF) Microstructure Surrogate Model is a machine-learning-based tool. It predicts statistics of microstructures that are produced by the LPBF additive manufacturing process. It includes a series of codes for training, testing, and analyzing the model as well as utility scripts for handling data. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Moser, Daniel [Sandia National Lab. (SNL-CA), Live↗

Development of GRCop-84 for Rocket Engine Applications

GRCop-84 (Cu-8 at.% Cr-4 at.% Nb) has been under development at the NASA Glenn Research Center for several years. The alloy possesses a unique combination of good thermal conductivity, high elevated temperature strength, long creep lives and long low cycle fatigue lives. The alloy is also more oxidation resistant than pure copper and most competitive alloys. The combination of properties has attracted attention from major rocket engine manufacturers who are interested in the alloy for the combustion chamber liner in their next generation of regeneratively cooled engines. It is also a strong candidate for various components in hypersonic vehicles, which also experience very high heat flux conditions. This presentation will discuss the alloy design strategies used to develop GRCop-84 and the various processing routes available for manufacturing components. The microstructure and mechanical properties of the alloy will be reviewed, as well as the results of actual hot fire testing of subscale rocket combustion chambers. The use of environmental and thermal barrier coatings to extend the performance to even higher levels will also be discussed.

Ellis, David L.↗

Effects of Exposures on Superalloys for Space Applications

The industry is demanding longer term service at high temperatures for nickel-base superalloys in gas turbine engine as well as potential space applications. However, longer term service can severely tax alloy phase stability, to the potential detriment of mechanical properties. Cast Mar-M247LC and wrought Haynes 230 superalloys were exposed and creep tested for extended times at elevated temperature. Microstructure and phase evaluations were then undertaken for comparisons.

Gabb, Tim↗