Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase transformations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Influence of Temperature on the Texture Distribution in Two-Phase Region Hot Deformation of Grain-Oriented Silicon Steel

Hot deformation simulation test of 3% Si grain-oriented silicon (CGO) steel was carried out at different temperatures, and evolution of microstructures and recrystallized textures in two-phase region was analyzed by electron backscatter diffraction and optical microscopy. The “δ → γ” and “γ → α” phase transformation points of the two-phase region measured by differential scanning calorimetry method are 1272 and 819 °C, respectively, which are within the ranges of 1300-1350 and 800-850 °C, measured by water quenching. The hot deformation temperature has a large effect on the microstructure and texture in the steel. A higher hot deformation temperature leads to higher degree of recrystallization and larger average grain size, more γ-fiber textures and cube {100} <001> texture, but the rotated cube {100} <011> texture is stable. The recrystallized microstructure was also affected by the phase compositions. While the cube {100} <001> texture results in typical austenite recrystallization texture, {111} textures lead to typical ferrite rolling textures.

36 MATERIALS SCIENCE↗

Pressure-induced phase transitions in multiferroic RbFe(MoO{sub 4}){sub 2}-Raman scattering study

High pressure Raman scattering experiments were performed on RbFe(MoO{sub 4}){sub 2}. These experiments revealed that two phase transitions take place in RbFe(MoO{sub 4}){sub 2} at very low pressures, i.e. between ambient pressure and 0.2 GPa and between 0.4 and 0.7 GPa. Raman results showed that at the first phase transition the room temperature P3-bar m1 phase transforms into the P3-bar phase, which is also observed at ambient pressure below 190 K. The second pressure-induced phase transition occurs into a low symmetry phase of unknown symmetry. The performed lattice dynamics calculations for the P3-bar m1 phase and ab initio calculation of the structural changes under hydrostatic pressure helped us to get better insights into the mechanism of the observed phase transitions. - Graphical abstract: Raman spectra of RbFe(MoO{sub 4}){sub 2} crystal in the high wavenumber region recorded at different pressures during compression experiment. Highlights: > RbFe(MoO{sub 4}){sub 2} exhibits two pressure-induced phase transitions below 0.7 GPa. > First phase transition is from the P3-bar m1 into P3-bar structure. > Phase transitions in RbFe(MoO{sub 4}){sub 2} are similar as in KFe(MoO{sub 4}){sub 2}. > Transitions' pressures are much lower for the rubidium compound.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evaluation of microstructural development in electron beam melted Ti-6Al-4V

In the current work an investigation of the microstructures of EBM built Ti-6Al-4V test bars has been performed using OM, SEM, TEM and XRD. It has been found that the prior {beta} phase, that formed during the initial solidification, possesses a column shaped morphology with growing direction parallel to built direction. Typical ({alpha} + {beta}) structures namely Widmanstaetten {alpha} platelets with rod-like {beta} phase formed on the interfaces of the fine {alpha} grains, have been observed in the columnar prior {beta} grains. Grain boundary {alpha} phase was found to be formed around the boundaries of the columnar prior {beta} grains. Different phases present in the parts, especially the BCC {beta} phases have been characterized. The TEM/EDX results indicate very high V composition in the {beta} phase. Results of TEM/SAED and XRD also revealed that a superlattice structure could be present in the {beta} phase. Phase transformation sequence is discussed according to the processing history and the microstructures observed. - Highlights: Black-Right-Pointing-Pointer {alpha} + {beta} and individual {beta} phase is observed and characterized by SEM, TEM and XRD. Black-Right-Pointing-Pointer {beta}-phase is identified as rod-like structure embedded in {alpha} matrix and platelets. Black-Right-Pointing-Pointer Phase transformation sequence is discussed as per thermal history and microstructures.

36 MATERIALS SCIENCE↗

Microstructural changes in an extruded Mg−Zn−Y alloy reinforced by quasicrystalline I-phase by small additions of calcium, manganese and cerium-rich mischmetal

The effects of calcium, manganese and cerium-rich mischmetal additions on the microstructure and texture of the extruded Mg−6Zn−1Y (wt.%) alloy have been investigated. The microstructure of the alloys consisted of a magnesium matrix embedding second phase particles aligned along the extrusion direction. The nature and volume fraction of the second phases depended on the alloying element. Thus, Ce-rich mischmetal promoted the formation of T-phase while calcium additions resulted in the formation of a ternary Mg−Zn−Ca compound. Only, manganese additions did not affect the existence of the I-phase present in the ternary alloy. The texture was measured and it was found that calcium addition has a significant effect weakening the extrusion texture. - Highlights: •In-situ HEXRD and DSC techniques are employed to identify phase transformations. •The existence of I-phase is not altered by manganese addition to Mg93Zn6Y1 (wt.%). •Calcium addition promotes Mg{sub 6}Zn{sub 3}Ca{sub 2} formation instead of I-phase. •Mischmetal addition induces the formation of coarse T-phase particles. •Texture depends on the nature of second phases and therefore of the extrusion pressure.

36 MATERIALS SCIENCE↗

The influence of A-site strontium ion in controlling the microstructure and electrical properties of P{sub 1−x}S{sub x}ZNZT ceramics

A Pb{sub 1−x}Sr{sub x}(Zn{sub 1/3}Nb{sub 2/3}){sub 0.2}(Zr{sub 0.5}Ti{sub 0.5}){sub 0.8}O{sub 3} (P{sub 1−x}S{sub x}ZNZT, 0.00 ≤ x ≤ 0.10) system was prepared through a conventional solid oxide process. Increasing addition of Sr{sup 2+} was found to induce a continuous decrease in grain size from 2.46 μm to 1.14 μm, accompanied by a phase transformation from coexisting rhombohedral and tetragonal phases to tetragonal phase only. The underlying mechanism of the evolution of dielectric and ferroelectric behavior in the P{sub 1−x}S{sub x}ZNZT ferroelectric ceramics was ascribed to the synergy between the grain size effect and the dilution of Pb-O covalency. Additionally, the grain size effect on domain wall displacement was found to be the main origin of the superior permittivity and piezoelectricity of the ceramics at intermediate grain size. The optimal electrical properties achieved for the P{sub 0.95}S{sub 0.05}ZNZT specimen at a grain size of about 1.79 μm, d{sub 33} = 465 pC/N, d{sub 33} × g{sub 33} = 11 047 × 10{sup −15} m{sup 2}/N make this material promising for multilayer energy harvesting device applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Thermal runaway mechanism of lithium-ion battery with LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathode materials

Battery safety is critical to the application of lithium-ion batteries, especially for high energy density battery applied in electric vehicles. In this paper, the thermal runaway mechanism of LiNi 0.8 Co 0.1 Mn 0.1 O 2 based lithium-ion battery is illustrated. And the reaction between cathode and flammable electrolyte is proved as the trigger of the thermal runaway accident. In detail, with differential scanning calorimeter tests for battery components, the material combination contributing to thermal runaway was decoupled. Characterization with synchrotron X-ray diffraction and transmission electron microscopy with in-situ heating proved that the vigorous exothermic reaction is initiated by the liberated oxygen species. The pulse of highly active oxygen species reacted quickly with the electrolyte, accompanied with tremendous heat release, which accelerated the phase transformation of charged cathode. Also, the mechanism is verified by a confirmatory experiment when the highly active oxygen species were trapped by anion receptor, the phase transformation of the charged cathode was inhibited. Clarifying the thermal runaway mechanism of LiNi 0.8 Co 0.1 Mn 0.1 based lithium-ion battery may light the way to battery chemistries of both high energy density and high safety.

25 ENERGY STORAGE↗

Stacking faults and alternate crystal structures for the shape-memory alloy NiTi

Here, we use ab initio calculations to study the role of stacking faults in connecting the high-temperature B2 and the theoretically predicted low-temperature B33 NiTi phases. In contrast with prior work, we describe the B 2 → B 33 phase transformation in terms of alternate bilayer shifts by 1 2 [100] on the ( 011 ) B 2 plane, obtaining a viable pathway; the same mechanism could also work with the B19 parent phase. We then examine B33-like structures built from alternate stacking sequences of B19 bilayers, constructed to have monoclinic tilt angles close to the experimentally reported NiTi B19' martensite, and find four low-energy stacking-fault variants with energies 5.8–8.5 meV/atom above the calculated B19' martensite structure, suggesting that such structures might appear as a part of the NiTi martensite phase at low temperatures. Investigating further the occurrence of specific coordinated planar shifts in NiTi systems, we report a dynamically stable NiTi B27 phase and find that it is only 1.2 meV/atom above the calculated B33 ground-state structure, thus having a potential to also play a role in NiTi martensitic phase transformation.

36 MATERIALS SCIENCE↗

On the Localized Nature of the Structural Transformations of Li2MnO 3 Following Electrochemical Cycling

Although the Li-excess layered-oxide Li2MnO3 has a high theoretical capacity, structural transformations within the oxide during electrochemical cycling lead to relatively low experimental capacities, hindering its use in practical applications. Here, aberration-corrected scanning transmission electron microscopy/electron energy loss spectroscopy and high-resolution X-ray diffraction are used to characterize the oxide following electrochemical cycling. Microscopy reveals the coexistence of regions with local monoclinic, spinel, and rock-salt symmetries, indicating localized and inhomogeneous structural evolutions. Crystal structure transformations are observed both at the particle surface and in the bulk. At the surface, these transformed regions resemble spinel Mn3O4 or rock-salt MnO, consistent with oxygen loss. In the bulk, the regions resemble defect spinels, such as the layered-spinel LixMn4/3O4, which suggest a partial phase transformation consistent with oxygen retention. Both microscopy and diffraction data of the cycled sample indicate areas of pristine Li2MnO3; the presence of such areas, in close proximity to LixMn4/3O4 areas, suggests that the layered to spinel structure transformation is partially reversible. Spinel, disordered rock salt, and pristine areas are also observed in Li2MnO3 samples intentionally damaged by electron beam irradiation. This observation indicates that the dynamic processes resulting in phase transformations can be studied for a variety of oxide systems by a judicious selection of irradiation conditions.

aberration-corrected scanning transmission electro↗

High-energy synchrotron x-ray study of deformation-induced martensitic transformation in a neutron-irradiated Type 316 stainless steel

An unusual tensile deformation behaviour in the form of a propagating band along the sample gauge was observed in two neutron-irradiated 316 stainless steel samples during room-temperature tests, leading to a combination of high strength and high ductility. These bands were not observed in an unirradiated counterpart. With the help of in situ high-energy synchrotron x-ray diffraction, the phase-specific crystal information was tracked at different deformation levels in each sample. Post-irradiation and post-deformation samples were examined using electron microscopy to characterize various microstructural features. All samples displayed a deformation-induced martensitic phase transformation, which was identified as a second strain-hardening mechanism accompanying the dislocation hardening. The deformation-induced martensitic transformation was rationalized by the effect of applied stress on the effective martensite start temperature. The results showed that the irradiation did not alter the dislocation hardening and the martensitic transformation mechanisms, but the increased yield strength in irradiated materials facilitated the localized phase transformation at the onset of plastic deformation, in contrast to the unirradiated material which required pre-straining. The hardening effect of the martensitic transformation reduced the tendency towards necking and mitigated the loss of ductility in the irradiated material by carrying the deformation in the form of a propagating band. Despite the beneficial effect from the martensitic transformation, this study indicates that this mechanism cannot not be activated at typical operating temperatures of nuclear reactors.

36 MATERIALS SCIENCE↗

Extended continuous cooling transformation diagram for 410 stainless steel encompassing δ → γ and γ → αʹ transformations determined by dilatometry

In this study, we use dilatometry to construct an extended Continuous Cooling Transformation (CCT) diagram for 410 stainless steel, capturing both δ → γ and γ → αʹ transformations specifically for directed energy deposition (DED) additive manufacturing (AM) applications. To ensure that the findings are representative of AM specific microstructures and compositions, dilatometry coupons were extracted from a wire arc DED wall, thereby preserving the inherent microstructural and compositional variability within the material. The on-heating phase transformations, including A c1 , A c3 , and γ → δ, were found to be essentially location independent, despite the typical heterogeneity associated with AM. Conversely, increasing cooling rates were observed to shift the start and finish temperatures of both δ → γ and γ → αʹ transformations to lower values. The resulting extended CCT diagram offers a more complete depiction of phase transformation behavior in the system, enabling accurate microstructure evolution modeling and residual stress predictions specifically for directed energy deposition additive manufacturing applications.

Additive manufacturing↗

Synthesis and Photonic Sintering of Proton Conducting Lanthanide Nickelates

Lanthanide nickelate perovskites are known proton conductors at intermediate temperatures (350-600°C). They are attractive targets for proton conducting fuel cells and electrolyzers due to their operational temperature range and their stability in the presence of CO 2 . These materials have the formula LNiO 3 , with the lanthanide L = La, Ce, Pr, Nd, or Sm. Sintering is challenging due to phase transformations that occur at lower temperatures than those required for sintering. In this project, a series of lanthanide nickelate perovskites was synthesized via both a precursor solid solution method and the glycine nitrate process. Powders derived from the precursor solid solution method for LaNiO 3 and NdNiO 3 were sintered at Utility Global Inc. at various temperatures utilizing fast photonic sintering. LaNiO 3 was successfully sintered while maintaining the perovskite phase. NdNiO 3 underwent a phase transformation at all the conditions tested. The stability of the perovskite phase decreases moving right across the lanthanides in the periodic table, while the expected proton conductivity increases. These results will inform further investigations into lanthanide nickelate perovskites toward the goal of producing a free-standing, sintered, proton-conducting membrane.

36 MATERIALS SCIENCE↗

Processability and Material Behavior of NiTi Shape Memory Alloys Using Wire Laser-Directed Energy Deposition (WL-DED)

Utilizing additive manufacturing (AM) techniques with shape memory alloys (SMAs) like NiTi shows great promise for fabricating highly flexible and functionally superior 3D metallic structures. Compared to methods relying on powder feedstocks, wire-based additive manufacturing processes provide a viable alternative, addressing challenges such as chemical composition instability, material availability, higher feedstock costs, and limitations on part size while simplifying process development. This study presented a novel approach by thoroughly assessing the printability of Ni-rich Ni55.94Ti (Wt. %) SMA using the wire laser-directed energy deposition (WL-DED) technique, addressing the existing knowledge gap regarding the laser wire-feed metal additive manufacturing of NiTi alloys. For the first time, the impact of processing parameters—specifically laser power (400–1000 W) and transverse speed (300–900 mm/min)—on single-track fabrication using NiTi wires in the WL-DED process was examined. An optimal range of process parameters was determined to achieve high-quality prints with minimal defects, such as wire dripping, stubbing, and overfilling. Building upon these findings, we printed five distinct cubes, demonstrating the feasibility of producing nearly porosity-free specimens. Notably, this study investigated the effect of energy density on the printed part density, impurity pick-up, transformation temperature, and hardness of the manufactured NiTi cubes. The results from the cube study demonstrated that varying energy densities (46.66–70 J/mm3) significantly affected the quality of the deposits. Lower to intermediate energy densities achieved high relative densities (>99%) and favorable phase transformation temperatures. In contrast, higher energy densities led to instability in melt pool shape, increased porosity, and discrepancies in phase transformation temperatures. These findings highlighted the critical role of precise parameter control in achieving functional NiTi parts and offer valuable insights for advancing AM techniques in fabricating larger high-quality NiTi components. Additionally, our research highlighted important considerations for civil engineering applications, particularly in the development of seismic dampers for energy dissipation in structures, offering a promising solution for enhancing structural performance and energy management in critical infrastructure.

Dabbaghi, Hediyeh↗

Imaging the Hydrogen Absorption Dynamics of Individual Grains in Polycrystalline Palladium Thin Films in 3D

Defects such as dislocations and grain boundaries often control the properties of polycrystalline materials. In nanocrystalline materials, investigating this structure-function relationship while preserving the sample remains challenging because of the short length scales and buried interfaces involved. Here we use Bragg coherent diffractive imaging to investigate the role of structural inhomogeneity on the hydriding phase transformation dynamics of individual Pd grains in polycrystalline films in three-dimensional detail. In contrast to previous reports on single- and polycrystalline nanoparticles, we observe no evidence of a hydrogen-rich surface layer and consequently no size dependence in the hydriding phase transformation pressure over a 125-325 nm size range. We do observe interesting grain boundary dynamics, including reversible rotations of grain lattices while the material remains in the hydrogen-poor phase. The mobility of the grain boundaries, combined with the lack of a hydrogen-rich surface layer, suggests that the grain boundaries are acting as fast diffusion sites for the hydrogen atoms. Such hydrogen-enhanced plasticity in the hydrogen poor phase provides insight into the switch from the size-dependent behavior of single-crystal nanoparticles to the lower transformation pressures of polycrystalline materials and may play a role in hydrogen embrittlement.

Yau, Allison↗

Correlation between long range and local structural changes in Ni-rich layered materials during charge and discharge process

Ni-rich cathode materials can deliver higher energy density with a lower cost compared with other conventional layered oxide materials. However, the cycling performance of Ni-rich materials needs further improvement, and the irreversible phase transformation related to the cell failure is not fully understood yet. Although an H1-H2-H3 structural change process is revealed, a more specific explanation about the difference of these hexagonal phases is needed for deeper comprehension and further targeted modification of Ni-rich materials. In this work, the different phase transformation mechanisms of LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622) and LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) are investigated by C X-ray diffraction (XRD) measurement, and the relationship between structural change and capacity degradation is discussed, showing that H3 phase can be harmful for cycling. In addition, Li-6 solid state nuclear magnetic resonance (ss-NMR) experiments are carried out for detecting the Li chemical environment at different state of charge, and the data can be associated with structural change obtained from in operando XRD results. From the analysis mentioned above, a new explanation of H1/H2/H3 is given, and a relationship between long range and local structural change has been put forward for the first time.

36 MATERIALS SCIENCE↗

Polymorphic transformations and thermal expansion in AgCuSe{sub 0.5}(S,Te){sub 0.5} crystals

The high-temperature X-ray diffraction technique is used to study AgCuSe{sub 0.5}(S,Te){sub 0.5} crystals. It is shown that, at room temperature, the AgCuSe{sub 0.5}S{sub 0.5} crystal is composed of Cu{sub 1.96}S and AgCuSe phases. At a temperature of 695 K, these phases transform into a single face-centered cubic (fcc) phase. The transformation is reversible. The AgCuSe{sub 0.5}Te{sub 0.5} composition consists of three phases, specifically, Cu{sub 2}Te, AgCuSe, and a cubic phase. At 444 K, both orthorhombic phases simultaneously transform into a diamond-like cubic phase. In this transformation, the cubic phase plays the role of a seed. From the temperature dependence of the lattice parameters, the thermal-expansion coefficients of the phases involved in both compositions are calculated for the main crystallographic directions.

36 MATERIALS SCIENCE↗

Additively Manufacturing Nitinol Shape Memory Alloys for Advanced Actuator Designs

The objective of this research was to understand the role of feedstock production in the phase transformation behavior of additively manufactured Ni-Ti alloys for advanced actuator design. Industrial adoption of additively manufactured Ni-Ti alloys depends on the ability to produce repeatable phase transformation behavior, quantified here by the austenite to martensite transformation on heating. Small variations in the alloy composition may have a significant effect on the temperature at which this transformation occurs. This project showed that the powder characteristics play an important role in determining this behavior. Increases in the surface area per unit volume of the powder, either as a function of size distribution or morphology, have the effect of reducing the Ti content in the alloy through the formation of Ti-rich oxides on the powder surface, which has the effect of depressing the transformation temperature. Preferential Ni vaporization during additive manufacturing can partially offset this effect. To achieve repeatable results, it is important to understand the effect of powder oxidation, and to control the powder characteristics.

36 MATERIALS SCIENCE↗

Development of a Laser Ultrasonics-based Approach for Rapid Screening of High Entropy Alloys

This project utilized a laser ultrasonic technique to systematically study temperature-induced evolution of material properties in a set of interrelated binary alloys and a high entropy alloy (HEA) fabricated using arc-melting and spark plasma sintering processes. This technique involved the use of a nanosecond duration, high-intensity pulsed laser to thermo-elastically generate ultrasonic waves that propagate in the bulk of the metal alloy. Sub-nanometer-scale displacements associated with the propagating bulk ultrasonic waves were detected along the epicenter on the opposite surface of the sample using a 1 GHz bandwidth photorefractive interferometer. Phase transformations and microstructural changes were inferred from the temperature-dependent trends in the bulk acoustic velocities and features in the ultrasonic epicentral waveforms measured in the binary alloys. These inferences were then correlated with electron/optical microscopy observations and predictions using calculations of phase diagrams (CALPHAD). The results showed that the laser-generated ultrasonic pulses were strongly influenced by changes in material microstructure and could accurately track thermally driven phase transformations and detect the presence of microscale heterogeneities (grain boundaries, dendritic structures, etc.) in the set of binary alloy samples. The measurement approach was then applied to a quinary HEA sample for estimating phase transition temperature and determining microstructural heterogeneity. The rapid, non-contact and non-destructive ultrasonic testing approach demonstrated here is amenable to high throughput combinatorial investigations that can be applied to graded composition HEAs produced using advanced manufacturing methods. When paired with atomistic simulations and CALPHAD modeling, this approach can overcome the bottlenecks faced by current material characterization methods in efficiently screening the vast discovery space of HEAs that spans over a hundred million unique quinary alloy compositions.

36 MATERIALS SCIENCE↗

Elastic Metal Alloy Refrigerants: Thermoelastic Cooling

BEETIT Project: UMD is developing an energy-efficient cooling system that eliminates the need for synthetic refrigerants that harm the environment. More than 90% of the cooling and refrigeration systems in the U.S. today use vapor compression systems which rely on liquid to vapor phase transformation of synthetic refrigerants to absorb or release heat. Thermoelastic cooling systems, however, use a solid-state material—an elastic shape memory metal alloy—as a refrigerant and a solid to solid phase transformation to absorb or release heat. UMD is developing and testing shape memory alloys and a cooling device that alternately absorbs or creates heat in much the same way as a vapor compression system, but with significantly less energy and a smaller operational footprint.

ARPA-E↗