Search NASA⌕ Search

SEARCH · Search NASA

Results for “ACCELERATION STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Microstructurally resolved electrochemical evolution of mechanical- and irradiation-induced damage in nuclear alloys

Abstract There is a need for high-throughput, scale-relevant, and direct electrochemical analysis to understand the corrosion behavior and sensitivity of nuclear materials that are exposed to extreme (high pressure, temperature, and radiation exposure) environments. We demonstrate the multi-scale, multi-modal application of scanning electrochemical cell microscopy (SECCM) to electrochemically profile corrosion alterations in nuclear alloys in a microstructurally resolved manner. Particularly, we identify that both mechanically deformed and irradiated microstructures show reduced charge-transfer resistance that leads to accelerated oxidation. We highlight that the effects of mechanical deformation and irradiation are synergistic, and may in fact, superimpose each other, with implications including general-, galvanic-, and/or irradiation-activated stress-corrosion cracking. Taken together, we highlight the ability of non-destructive, electrochemical interrogations to ascertain how microstructural alterations result in changes in the corrosion tendency of a nuclear alloy: knowledge which has implications to rank, qualify and examine alloys for use in nuclear construction applications.

Chen, Xin↗
DOE OSTI2026

Atomistic Mechanisms of Stress-Dependent Molten Salt Corrosion in NiCr Alloys

Ni-based structural alloys in molten salt environments often experience simultaneous mechanical loading and corrosive attack, yet the mechanisms governing stress-corrosion interactions remain unclear. Prior studies largely emphasize tensile stress, while the role of compressive stress has received limited attention. Here, reactive molecular dynamics simulations are used to investigate the coupled effects of applied strain and corrosion in Ni 0.75 Cr 0.25 exposed to molten FLiNaK at 800 °C. A Σ5(210) grain boundary model is subjected to tensile (+4%) to compressive (−4%) uniaxial strains, and corrosion behavior is evaluated through fluorine adsorption, charge redistribution, and grain boundary evolution. Tensile strain accelerates intergranular corrosion susceptibility by reducing local atomic packing through elastic dilation and increasing excess free volume at the grain boundary, which enhances atomic mobility and salt infiltration. In contrast, compressive strain can suppress corrosion by promoting the formation of a ridge-like surface layer along the grain boundary, limiting salt access to the underlying alloy. These results provide atomistic insight into how stress states influence grain boundary corrosion in molten salts.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

An integrated in-situ coordination strategy enabling high-performance layered cathodes for sodium-ion batteries

O3-type layered transition metal oxide cathodes hold tremendous potential in sodium-ion batteries (SIBs) due to their low cost and high energy density. However, the structure instability associated with detrimental phase transitions and severe interface parasitic reactions exacerbate the material's electrochemical performance degradation. Herein, we develop an integrated in-situ coordination strategy via heteroatomic modulation inducing coherent epitaxial layer to collaboratively enhance the overall framework robustness from surface to bulk. The theoretical calculation and multiple in/ex-situ characterizations demonstrate the charge density around oxygen is redistributed, which promotes the electron localization, thus widening the NaO 2 lattice space and accelerating the Na + transport dynamics. Furthermore, the formed strengthened oxygen bond energy effectively distributes the long-range coordination of Mn 3+ O 6 octahedron, thereby alleviating Jahn-Teller distortion and local stress. Importantly, the in-situ formed conformal buffer layer dramatically relieves the adverse interface side reactions, facilitating the construction of robust cathode-electrolyte interface, which ameliorate the whole structure stability of designed materials. Consequently, the optimized NFMZ@NZO-1.0 exhibits the excellent cycling stability with 80.2% capacity retention after 300 cycles at 1C, and delivers a high discharge capacity of 107.1 mAh g −1 at 10C. In conclusion, this distinctive coupling strategy provides valuable insights for developing high-performance layered cathode materials in SIBs.

Coherent epitaxial layer↗
DOE OSTI2024

A critical review of irradiation-induced changes in reactor pressure vessel steels

A large body of work has been conducted to investigate the embrittlement and degradation of reactor pressure vessel (RPV) steels. This includes experiments on alloys with different compositions, performed in research and test reactors and ion accelerators that span various temperatures, fluxes, and fluences. In this paper, we perform a critical review of the published experimental data and compile experimentally reported values for dislocation loop size/density, precipitate size/density and yield stress into an easily downloadable format that can be used by both experimentalists and modelers. This thorough experimental review is complemented by a brief review of simulation efforts at atomistic and mesoscopic length scales. Finally, this paper highlights key aspects of the behavior of RPV steels under irradiation, identifies gaps or discrepancies in current understanding, and identifies priority future research directions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Magnetic and Mechanical Analysis of Bi-2212 Rutherford Cable in a Cos-Theta Sub-Scale Dipole Coil

The U.S. Magnet Development Program (US-MDP) explores high-field accelerator magnets compatible with operational conditions beyond the limits of Nb$_3$Sn technology. The ongoing R&D High-Temperature Superconductors (HTS) suggests using Bi$_2$Sr$_2$CaCu$_2$O$_{8-x}$ (Bi-2212) as superconducting element. Bi-2212 Rutherford cables maintain a high critical current (I$_C$) when exposed to a large external magnetic field. However, Bi-2212 exhibits an oversensitive stress-strain response when subject to large Lorentz forces. This paper reports on the magnetic and mechanical analysis of the Bi-2212 cosine-theta insert being developed at Fermilab for a hybrid magnet composed of two external layers of Nb$_3$Sn and two internal layers of Bi-2212. We performed a FEM analysis of the insert to estimate the HTS stress state in the coil's strands under magnetic and mechanical loads.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Post-build stress-relief optimization for laser powder bed fusion 316H stainless steel

Nuclear energy remains a critical component of a diversified and efficient energy portfolio, offering reliable, high-capacity, and low-carbon power. However, in the U.S., aging infrastructure and the slow qualification and deployment of advanced materials and manufacturing techniques hinder progress in next-generation reactor technologies. This study explores the application of laser powder bed fusion (LPBF) additive manufacturing for stainless steel 316H, with a focus on optimizing post-build heat treatments to enhance material properties for high-temperature nuclear applications. The research targets the optimization of stress-relief temperatures to alleviate postbuild residual stresses, ensuring improvements in the microstructural corelated properties. A series of microstructural and mechanical evaluations were performed on LPBF-printed SS-316H samples which were subjected to annealing at temperatures varying between 650 °C and 850 °C. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analyses revealed that increasing the heattreatment temperature accelerated dislocation recovery. Vickers microhardness measurements showed an initial reduction in values, followed by stabilization over extended durations at all the temperatures. While higher temperatures facilitated faster recovery, they also promoted carbide precipitation along grain and solidification cell boundaries, narrowing the safe processing window. In contrast, heat treatment at 650°C preserved the cellular substructure and enabled controlled carbide precipitation over time. In conclusion, these findings highlight the importance of time–temperature optimization and suggest that 650°C for up to 2 h provides the most favorable balance between recovery and carbide control for a stress-relief treatment.

316 stainless steel↗
DOE OSTI2025

Mechanical form factors and densities of nonrelativistic fermions

The hadron physics community has been actively debating the interpretation of so-called mechanical properties of hadrons. Nonrelativistic quantum-mechanical systems like the hydrogen atom have been appealed to in these debates as analogies. Since such appeals are likely to continue, it is important to have Galilei-covariant expressions for matrix elements of the energy-momentum tensor. In this work, I obtain Galilei-covariant breakdowns of such matrix elements into mechanical form factors, with a special focus on spin-half states. I additionally study the spatial densities associated with these form factors, using the pilot wave interpretation to guide their breakdown into contributions from internal structure and from quantum-mechanical effects such as wave packet dispersion. For completeness, I also obtain nonrelativistic Breit frame densities.

form factors↗
DOE OSTI2026

Effect of glutathione-coated Mn-doped ZnS quantum dots on nutrient delivery in basil ( Ocimum basilicum ) plants

Ensuring efficient nutrient delivery while minimizing environmental impacts remains a significant challenge for modern agriculture. Nanotechnology-based fertilizers offer promising strategies to improve nutrient uptake and bioavailability in plants. This research aims to evaluate the use of Glutathione-coated Manganese-doped Zinc Sulfide quantum dots (GSH-ZnS-Mn QDs) as a potential nano fertilizer for basil (Ocimum basilicum). QDs' physicochemical properties were characterized using UV–Vis spectroscopy, photoluminescence, FTIR, and energy-dispersive X-ray spectroscopy, confirming successful Mn doping and glutathione surface functionalization. Basil plants were exposed to different concentrations of GSH-ZnS-Mn QDs under soil and hydroponic conditions. Plant growth parameters, oxidative stress responses, photosynthetic pigments, and macro- and micronutrient uptake were assessed using biochemical assays and inductively coupled plasma optical emission spectrometry (ICP-OES). Elemental uptake, spatial distribution, and zinc speciation were further investigated using synchrotron-based micro-X-ray fluorescence (μ-XRF) imaging and X-ray absorption near-edge structure (XANES) spectroscopy. Results show that exposure to GSH-ZnS-Mn QDs resulted in a concentration-dependent increase in leaf and stem biomass, accompanied by enhanced Zn accumulation in plant tissues. Catalase activity decreased across all tested concentrations, suggesting a shift toward glutathione-dependent antioxidant pathways rather than oxidative damage. Chlorophyll levels exhibited moderate reductions at higher concentrations. The higher increase in macronutrient (K, Ca, and Mg) uptake was reported in plants exposed to 200 ppm of QDs. μ-XRF imaging indicated a selective accumulation of Zn in roots and stems, with partial translocation to leaves. XANES analyses revealed that Zn from QDs was mainly converted into organic Zn species, such as Zn-phytate, Zn-acetate, and Zn-cysteine, indicating transformation and complexation within the plant. The findings demonstrate that a glutathione coating on GSH-ZnS-Mn QDs improves biocompatibility and nutrient delivery efficiency. These results highlight the relevance of surface functionalization in regulating nanoparticle fate, transformation, and nutrient bioavailability, supporting the potential application of GSH–ZnS–Mn QDs as modern nano fertilizers.

Basil↗
DOE OSTI2025

Ab Initio Molecular Dynamics Insights into Stress Corrosion Cracking and Dissolution of Metal Oxides

Oxide phases such as α-Fe2O3 (hematite) and α-Al2O3 (corundum) are highly insoluble in water; however, subcritical crack growth has been observed in humidity nonetheless. Chemically induced bond breaking at the crack tip appears unlikely due to sterically hindered molecular transport. The molecular mechanics of a crack in corundum with a reactive force field reveal minimal lattice trapping, leading to bond breaking before sufficient space opens for water transport. To address this, we model a pre-built blunt crack with space for H2O molecule adsorption at the tip and show that it reduces fracture toughness by lowering the critical J-integral. Then, we explore stress-enhanced dissolution to understand the mechanism of crack tip blunting in the oxide/water system. Density functional theory combined with metadynamics was employed to describe atomic dissolution from flat hematite and corundum surfaces in pure water. Strain accelerates dissolution, stabilizing intermediate states with broken bonds before full atom detachment, while the free energy profile of unstrained surfaces is almost monotonic. The atomistic calculations provided input for a kinetic model, predicting the shape evolution of a blunt crack tip, which displays three distinct regimes: (i) dissolution primarily away from the tip, (ii) enhanced blunting near but not at the apex, and (iii) sharpening near the apex. The transition between regimes occurs at a low strain, highlighting the critical role of water in the subcritical crack growth of oxide scales, with dissolution as the fundamental microscopic mechanism behind this process.

Chemistry↗
DOE OSTI2026

A stress-based fracture model for reacting metal ejecta

The evolution of reacting metal ejecta continues to be a topic of interest at the forefront of metals in reactive and extreme environments. Ejecta are small particles formed when the surface of a metal undergoes Richtmyer–Meshkov instability from a strong shock. Experiments have shown that in the case where ejecta are in ambient conditions that induce a reaction, the ejecta behave irregularly. The ejecta temperature rises and then plateaus, and the acceleration profile shows unexpected jumps. These variations are assumed to be related to the exothermic heat release and particle mass loss caused by the reaction. To explain this phenomenon, efforts to model this in simulations have increased. While current models can capture many of these physical processes, they currently assign a constant reaction shell thickness with little physical reasoning. This work remedies this problem by assigning a dynamic physically informed shell thickness to the reacting particles, using solid analysis. The shell thickness of the particles impacts the rate of change of reacted mass in the system, as well as the rate at which the particles react. The model is based on a simple stress–strain relationship and gives a dynamic assignment for when the reacting particle should begin to fracture. We compare our model to the previous computational and simulation data to analyze the effects of different model parameters.

42 ENGINEERING↗
DOE OSTI2024

In-situ hydrogen microstructural characterization of Si heterojunction passivation: Addressing V OC degradation and mitigation pathways

Si heterojunction (SHJ) solar cells have demonstrated record efficiency >27%, approaching the theoretical limit of ≈ 29%, primarily due to best surface/interface defect passivation provided by deposited thin layers of hydrogenated amorphous silicon (a-Si:H). Such excellent surface/interface passivation reduces recombination loss and result in >100 mV improvement of cell open circuit voltage (V OC ) to ≈ 750 mV, thus the cell efficiency. However, fielded SHJ modules exhibit loss of V OC and hence efficiency over time in years, presumably due to degradation related to a-Si:H layers. This adversely affects the technology’s market acceptance, and levelized cost of energy (LCOE). It is hypothesized that the origin of a-Si:H degradation is somehow related to the presence of weak Si–Si bonds and hydrogen in a-Si:H films. The objective of this project is to test this hypothesis by directly measuring chemical and structural changes occurring within SHJ component layers and solar cells. This is achieved by developing an innovative in-situ Fourier transform infrared (FTIR) spectrometry apparatus to monitor hydrogen microstructural changes occurring within amorphous silicon and decipher hydrogen evolution kinetics over time when samples are exposed to heat and/or light stress. These in-situ measured hydrogen microstructural changes are correlated to the changes in effective minority carrier lifetime (τ eff ), implied V OC (iV OC ), surface recombination velocity (S), and cell V OC . These mechanistic understandings will provide critical guidance to mitigate the V OC -driven degradation of SHJ solar cell performance. Passivation optimization and degradation analysis of individual SHJ component structures were achieved through systematic deposition of three symmetric structures and the completed SHJ solar cell structure. The three symmetric structures used were intrinsic a-Si:H [(i)a-Si:H] layers in a bilayer structure, intrinsic and p-type doped stacked layers [(i-p)a-Si:H] representing the front heterojunction in the SHJ cell, and intrinsic and n-typed doped stacked layers [(i-n)a-Si:H] representing the back-side back surface field (BSF) in the SHJ cell. State-of-the-art passivation qualities are demonstrated by a champion iV OC of 740 mV for the (i)a-Si:H layers, and the (i-n)a-Si:H symmetric structure. A 725 mV iV OC is observed for the (i-p)a-Si:H symmetric structure. These symmetric passivated SHJ component structures were subsequently subjected to different accelerated lifetime (ALT) stressors to identify which conditions contribute the most to iV OC degradation. Degradation of the thin (10 nm) (i)a-Si:H passivation layers without any additional overlying layers is minimal; complexity of this study arises due to unavoidable surface oxidation of (i)a-Si:H layer during most of the stress application, which is likely irrelevant for a full SHJ cell configuration with overlying protective layers. The iV OC degradation of symmetric structures is found to occur primarily at the (i-p)a-Si:H passivation stack under dark heat stress with associated hydrogen loss from the (p)a-Si:H layer. An activation energy for increase in S (defect creation) of 0.65 eV can be correlated to the activation energy of ≈ 0.4 eV for hydrogen loss from the (i-p)a-Si:H stack. This also suggests the presence of weakly bonded hydrogen in the (p)a-Si:H films, which effuses out of the film stack at such low activation energy. When light and heat stress are applied together, similar hydrogen loss from (i-p)a-Si:H stack is observed, however, does not appreciably degrade iV OC or increase S. This is an important result and departure from direct correlation between hydrogen loss and defect creation. This perhaps indicates additional defect chemistries or annealing that might be occurring in the presence of light requiring further detailed defect measurements. The full SHJ cell structure used for this project is depicted in Fig.1(d). SHJ cells with an initial V OC ≈ 700 mV were fabricated and subjected to similar ALT stress conditions. Cell V OC is found to degrade the most under dark heat stress and is confirmed by observed hydrogen migration out of the (i-p)a-Si:H stack. However, hydrogen cannot escape from the cell stack, it accumulates near the (p)a-Si:H/ITO contact interface, where ITO acts as a barrier preventing hydrogen loss. Furthermore, light-heat combined stress does not degrade V OC appreciably, confirming the occurrence of a defect annealing process.

14 SOLAR ENERGY↗
DOE OSTI2024

Rapid assessment of the creep rupture life of metals: A model enabling experimental design

Prediction of the creep rupture life of engineering metals is critical for qualification and design of new materials. The use of long-term creep tests and the need to quantify the performance variability in a priori similar systems hinder the rapid creep assessment of a given material. Therefore, it is essential to develop methods that can extrapolate the long-term performance of alloys and the associated variability from short-term experiments. To this end, this study introduces a new model which enables the estimation of the rupture life of a material for a given stress and temperature. This model relies on two components. First, a new relation for the minimum creep rate (MCR) of materials is introduced. It includes a stress dependent stress exponent allowing the model to capture the variation of MCR across a wide range of temperatures and stresses. Second, employing the Monkman-Grant (MG) law, we establish a relation between stress, temperature and creep rupture life. Together, these two elements yield a new closed-form mathematical expression for the Larson Miller parameter as a function of stress and temperature. This expression captures the creep rupture time for many metals (Gr91, Copper, Gr122 and 347H) and compares favorably with alternate empirical approaches. The model is then used to assess the minimum duration of creep rates necessary to qualify the material up to 100000h. Furthermore, it is found that depending on the material system, creep tests as few as five limited to 5000 h for steels (Gr91, Gr122, 347H) and 100 h for copper are sufficient to model creep lifetimes. Finally, using a Bayesian inference-based approach to calibrate the model, we demonstrate that variability in rupture life can be captured via the quantification of the uncertainty in the model parameters and extrapolated from a limited number of short to moderately short creep tests; thereby paving the way for accelerated creep testing.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Importance of Considering Near-Surface Attenuation in Earthquake Source Parameter Estimation: Insights from Kappa at a Dense Array in Oklahoma

ABSTRACT Separating earthquake source spectra from propagation effects is challenging. The propagation effect contains a site-dependent term related to the high attenuation of shallow sediments. Neglecting the site-dependent attenuation can cause large biases and scattering in the corner-frequency (fc) estimates, resulting in significant stress-drop deviations. In this study, we investigate shallow attenuation at the LArge-n Seismic Survey in Oklahoma (LASSO) and site-related biases and scattering in source parameter measurements due to simplified attenuation models. We measure the high-frequency spectral decay parameter kappa on the vertical acceleration spectra of regional earthquakes (125 km away). The site-dependent kappa (κ0,acc) suggests that attenuation increases rapidly at shallow depth and is highly site-dependent. 10%–75% of the attenuation is site-dependent for S waves and even larger for P waves. The quality factor for S waves (QS) ranges from 10 to 100 in the upper 400 m. QP for P waves is mostly below 10 within the same depth. The Quaternary sediments tend to be more attenuating (QS<30), but the Permian rocks also can have high attenuation. We demonstrate that using a non-site-dependent attenuation model in single-spectra fitting leads to large scattering in fc estimates among stations with apparent good fits. The apparent fc can significantly deviate when the range of site-dependent kappa is large or with a higher assumed source spectral fall-off rate n. The biases in apparent fc depend on site condition and distance; however, the correlation between fc and these factors might not be obvious, depending on model assumptions. An apparent increase of stress drop with magnitude in a previous study for local microearthquakes (1.3

Chang, Hilary↗
DOE OSTI2024

Development and test of a large-aperture Nb3Sn cos-theta dipole coil with stress management

The stress-managed cos-theta (SMCT) coil is a new concept which was proposed and is being developed at Fermilab in the framework of US Magnet Development Program (US-MDP) for high-field and/or large-aperture accelerator magnets based on low-temperature and high-temperature superconductors. A 120-mm aperture two-layer Nb3Sn SMCT dipole coil has been developed at Fermilab to demonstrate and test the SMCT concept including coil design, fabrication technology and performance. The first SMCT demo coil was fabricated and assembled with 60-mm aperture Nb3Sn coil inside a dipole mirror configuration and tested separately and in series with the insert coil. This paper summarizes the design, parameters, and quench performance of the 120-mm aperture SMCT coil in a dipole mirror configuration.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Electron beam irradiation effects on bulk metals: a comparative study of polycrystalline versus single-crystalline structures

This study investigates the effects of electron beam (e-beam) irradiation on the mechanical and structural properties of eight bulk metallic samples, comprising both polycrystalline (PC) and single-crystalline (SC) forms of Ni, Cr, V, and Ti. These metals were evaluated as potential candidates for beam exit windows in high-power (MW-class) particle accelerators. The primary objective is to identify metals capable of withstanding the conditions of high-power/MW-class e-beam accelerators and serve effectively as exit windows. Selection criteria were based on each metal’s intrinsic properties, power dissipation capability, and irradiation-induced changes in mechanical behavior, including hardness, elastic modulus, and defect density. Comprehensive characterization was conducted using field-emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDS), X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), and nanoindentation, performed both before and after exposure to a ~¿66 kGy dose from a 10 MeV e-beam accelerator. Results revealed that e-beam irradiation induced hardening in PC Ni, whereas PC Ti, commonly used in beam exit windows, exhibited softening. The observed softening in PC Ti is attributed to grain coarsening, elongation, and the formation of twins and twin boundaries, in contrast to the smaller, compressed grains in the pristine (Pr) PC Ti samples, consistent with the Hall–Petch relationship. The stresses due to twinning are small and insignificant in influencing the overall hardening of the PC Ti irradiated sample when compared to the stresses due to the dislocation density. Conversely, SC Ti samples exhibited irradiation-induced hardening. The SC Ti irradiated samples developed additional irradiation-induced modifications in crystallographic texture of (100), (101), (110), (200), (112), (004), and (211) as evidenced from the XRD results, which could probably explain the hardening effect that is caused by irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Greening Future Elevates Flash Drought Risk in Northern Mid‐to‐High Latitudes

Flash droughts have become a growing concern, as they can emerge rapidly and increase the risk of crop failure. Although past studies have investigated the meteorological drivers and future changes of flash drought, why flash drought is more frequent over humid and vegetated regions remains underexplored. This study delves further into the mechanism by which vegetation regulates flash drought and its future change using observations from multiple data sets and large ensemble simulations from three Earth system models. On an interannual timescale, both observations and simulations show robust increases in flash drought frequency and a higher flash-to-sub-seasonal drought ratio during spring or antecedent conditions with dense vegetation, supporting the important role of vegetation in flash drought occurrence, especially in the northern mid-to-high latitudes. In the latter regions, the large ensemble simulations show robust increases in flash drought (e.g., 67% and 46% increases in Eastern U.S. and North Asia in 2050–2100 relative to 1950–2000 under the high emission scenario), where the growing season is lengthening. Although greening might suggest reduced drought stress, it drives precipitation-soil moisture-evapotranspiration decoupling by increasing evapotranspiration partitioning to transpiration. As transpiration can access deep soil water through the plant root system, its increased portion can weaken the constraints of concurrent precipitation on evapotranspiration, thus accelerating soil moisture depletion under high evaporative demand, driving a slow-to-rapid drought transition. How vegetation regulates flash drought by regulating surface moisture budget is supported by observations and simulations. Although warming supports early planting, agriculture may increasingly be threatened by surging flash drought risk.

Drought↗
DOE OSTI2025

Rapid Bayesian High Entropy Alloy Designs Fabricated via Wire Arc Additive Manufacturing

Purpose: This project seeks to demonstrate a new high-throughput (rapid) alloy design technique applied to creating new high entropy alloys (HEAs) for extreme environments. High entropy alloys shift the design paradigm from being focused on a single principal element (e.g. nickel-based alloys) to target alloys that include high atomic fractions (X >10%) of multiple elements. These HEA materials can exhibit sluggish diffusion and enhanced corrosion resistance, ideal for potential applications in advanced ultra supercritical (A-USC) steam cycles for power generation. Scope: The addition of multiple elements in high atomic fractions creates an enormous design space that cannot easily be investigated by traditional material design strategies such as designed of experiments (DOE). This project utilizes a Bayesian machine learning algorithm that has been modified to work with calculation of phase diagrams (CALPHAD) software. This Bayesian algorithm reduces manual inputs and increase the likelihood of achieving an optimal solution. Compositional inputs to this algorithm will be assessed using existing material property models for high temperature strength and corrosion resistance. The target for alloy performance will be a 15% (~100 ⁰C) increase in allowable service temperature beyond heat-resistant stainless steels while maintaining or improving alloy cost and corrosion resistance. Haynes 230 was selected as a baseline, which is 57 wt% Ni with 22 wt% Cr 14 wt% W, and 2 wt% Mo as solid solution strengtheners. In addition to rapid design via Bayesian machine learning, the alloys were rapidly fabricated using a multi-wire arc additive manufacturing (mWAAM) technique which allows for precise control of alloy composition and assessing of alloy design “windows” to study composition effects. Build speeds for wire-arc additive processes are among the highest for additive technologies enabling rapid and reliable sample fabrication when compared to conventional methods such as arc button melting. The mWAAM samples will be rapidly characterized via instrumented indentation for room temperature modulus and strength and for elevated temperature strength via hot hardness tests. After being screened with hardness testing, potential alloys will be further evaluated with conventional microscopy techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM) to assess agreement with modeling results. The most promising compositions will also be evaluated by printing full sized tensile specimens for mechanical behavior tests at elevated temperatures. Results: Bayesian machine learning of a single performance function was initially used to optimize five performance metrics: 1) single phase stability, 2) yield strength, 3) creep resistance (low diffusion coefficient), 4) freezing range (weldability), and 5) material cost. The single performance function was suboptimal as assumptions had to be made about the results while formulating the optimization. A goal-oriented Bayesian optimization strategy (Hanaoka, 2021) was implemented with CALPHAD for use with the five metrics above. This multi-objective Bayesian optimization (MOBO) enabled the design of NiCrCoFe alloys with V and W additions. A base composition of NiCoCr was selected as Ni provides a stable FCC matrix, Cr aids corrosion/oxidation resistance, and Co is a solid-solutions strengthener that also improves creep by increasing the activation energy. Fe helps reduce diffusion coefficients and cost. Finally, V and W were selected for their reasonable solubility and high atomic misfit to aid in solid solution strengthening. Cracking of the mWAAM specimens was an early issue, and the Easton solidification cracking model (Easton et al., 2014a) was selected for addition to the MOBO function. High performing alloys fabricated by mWAAM included Ni 28 Cr 25 Co 26 Fe 15 V 8 and Ni 62 Cr 18 Co 1 Fe 3 W 15 . It was observed that even after adapting the mWAAM process for W, the W did not fully dissolve. To fully evaluate the Ni 62 Cr 18 Co 1 Fe 3 W 15 composition, a cored wire (80-20 NiCr sheath/powder core) was manufactured and printed via WAAM, and HIP’ing was utilized to homogenize and densify the printed alloy. The V and W alloys produced met metrics 1 (solid solution), 4 (solidification cracking), and 5 (cost). However, an unmodeled mechanism of thermal stress cracking was identified in the WAAM produced materials, perhaps exacerbated by the lack of grain boundary strengthening elements (B, C). Conclusions & Recommendations: A high-throughput (rapid) alloy design technique was applied to designing and manufacturing new high entropy alloys (HEAs) for extreme environments utilizing MOBO and mWAAM. The developed process was rapid and effective in addressing the mechanisms included in the model. The lack of grain boundary strengthening element additions (e.g., B, C) was a simplification that likely produced thermal stress cracking that turned into a large part of the investigation. Additions on the order of 0.005 wt% B and 0.05 wt% C likely would have minimized thermal stress grain boundary cracking. Overall, the high throughput design strategy is promising for rapid design of metrics-driven alloys for advanced ultra supercritical (A-USC) steam cycles for power generation. The MOBO and mWAAM process could be commercialized to accelerate metrics-driven alloy design. In addition, the cored-wire process utilized for scale-up is a promising high-volume process for WAAM alloy development and scale-up.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Establishing model credibility for process-microstructure-property relationships in additive manufacturing using exascale computing

Additive Manufacturing (AM) of alloys holds significant promise as a disruptive technology in various industries, yet its adoption is often hindered by challenges in achieving consistent part quality. These issues are primarily due to the complex process-microstructure-property (PSP) relationships inherent to AM. Computational models can greatly aid in understanding these relationships, but their widespread impact and adoption has been limited by a lack of validated, open-source, and computationally efficient PSP modeling frameworks and hardware limitations. Here, this study leverages the ExaAM software suite and data from the AMBench-2018 series of laser powder bed fusion (LPBF) benchmark experiments to perform a comprehensive model assessment, including verification, validation, sensitivity analysis, and uncertainty quantification. The RADICAL-EnTK workflow manager was used to perform an ensemble of heat transport, solidification, and mechanical response simulations on the exascale computer Frontier, considering uncertainties in critical model inputs such as laser spot size and nucleation parameters, and consisting of 125 explicit grain structure simulations and 7875 crystal plasticity simulations. For a selected location within the Inconel 625 AMBench-2018 test artifact, sensitivity analysis and uncertainty quantification were performed using the predicted distributions of grain structure and mechanical properties. Qualitative agreement was found between the predicted grain size and texture and the observed AMBench-2018 microstructure, the mean predicted yield stress was within 5% of the experimental measurement mean, and the mean predicted engineering stress at 5% strain was within 10% of the experimental measurement mean. The insights gained from development and validation of the ExaAM PSP modeling framework will help guide future directions for enhancing the credibility and reliability of PSP models in AM, thereby accelerating the adoption of AM technologies in various industries.

Additive manufacturing↗