Search NASA⌕ Search

SEARCH · Search NASA

Results for “ADHESIVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Enhanced Interfacial Strength in Carbon Fiber Composites via Mussel‐Inspired Sizing Polymers

Composite materials possess a high strength-to-weight ratio. A key determinant of their mechanical performance is the interfacial strength between the fibers and the matrix. Sizing agents are commonly used to improve this interface by promoting better adhesion, though optimizing this interaction remains a significant challenge. Here, this study evaluates the use of poly(catechol-styrene) (PCS), a mussel-inspired sizing agent, to enhance fiber–matrix bonding in carbon fiber composites. Woven carbon fiber laminates were dip-coated with varying concentrations of PCS (0.05 and 0.1 wt%) and subsequently fabricated using vacuum-assisted resin transfer molding followed by compression molding. Interlaminar shear strength (ILSS) tests showed improvements of 4% and 8% for the 0.05% and 0.1% PCS treatments, respectively. These results indicate that PCS is effective in reinforcing interfacial adhesion, thereby improving the mechanical integrity of carbon fiber-reinforced composites.

Carbon fiber composites↗
DOE OSTI2024

Effects of mercerization and fiber sizing of coir fiber for utilization in polypropylene composites

The use of natural fibers as an alternative to synthetic fibers for reinforcing composites is increasing. However, the poor interfacial adhesion between natural fibers and polymer matrices limits their applications. Several approaches have been considered to improve fiber-matrix adhesion via chemical and/or physical treatment. However, the effectiveness of these treatments varies based on the type of fiber, its source, and its composition. Thus, it is imperative to understand the effectiveness of treatment conditions. In this study, we investigated the influence of alkali treatment and fiber sizing on the chemical, thermal, morphological, and mechanical properties of coir fibers and the interface between coir fiber and polypropylene matrix. Further, it was found that using a 5 wt% sodium hydroxide solution for 6 h at room temperature was the optimal treatment condition that led to an improvement in tensile strength by 58%, tensile modulus by 71%, and elongation at break by 37% compared to untreated fibers, and an increment in interfacial shear strength (IFSS) between coir fibers and polypropylene matrix by 32%. The alkali treatment removed the fiber surface impurities, made the fiber surface rough, and enhanced the fiber crystallinity. Sizing of the alkali-treated fiber led to an improvement in IFSS by 87% with no modification of the fiber’s mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Interpreting test temperature and loading rate effects on the fracture toughness of polymer-metal interfaces via time–temperature superposition

Here, in this letter, we present interfacial fracture toughness data for a polymer-metal interface where tests were conducted at various test temperatures T and loading rates $\dot{δ}$. An adhesively bonded asymmetric double cantilever beam (ADCB) specimen was utilized to measure toughness. ADCB specimens were created by bonding a thinner, upper adherend to a thicker, lower adherend (both 6061 T6 aluminum) using a thin layer of epoxy adhesive, such that the crack propagated along the interface between the thinner adherend and the epoxy layer. The specimens were tested at T from 25 to 65 °C and $\dot{δ}$ from 0.002 to 0.2 mm/s. The measured interfacial toughness Γ increased as both T and $\dot{δ}$ increased. For an ADCB specimen loaded at a constant $\dot{δ}$, the energy release rate G increases as the crack length a increases. For this reason, we defined rate effects in terms of the rate of change in the energy release rate $\dot{G}$. Although not rigorously correct, a formal application of time–temperature superposition (TTS) analysis to the Γ data provided useful insights on the observed dependencies. In the TTS-shifted data, Γ decreased and then increased for monotonically increasing $\dot{G}$. Thus, the TTS analysis suggests that there is a minimum value of Γ. This minimum value could be used to define a lower bound in Γ when designing critical engineering applications that are subjected to T and $\dot{δ}$ excursions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mitigating municipal solid waste fouling in biofuel conversion via screw surface modifications

Here, municipal solid waste (MSW)'s 40–60 % carbon content makes it a feedstock for biofuel production via pyrolysis. One challenge in the conversion process is MSW fouling due to thermal decomposition. The accumulated deposit on the injection screw often leads to plugging and constriction. This study examined the morphology and composition of the MSW fouling deposit and conducted a thermal simulation to understand the temperature gradience of the injection screw. Surface modifications including smoothening and anti-adhesion coating were proposed for the injection screw to address the deposit problem. For evaluating the candidate mitigations, a bench-scale fouling test was developed with the gas environment, temperature, and sliding speed relevant to the contact interface between the MSW particles and the screw. Results suggested that a smoother screw surface could reduce the grip and a non-metallic coating with a lower surface energy could decrease adhesion, consequently leading to less fouling. Specifically, reducing the roughness from 2 to 0.6 and then to 0.2 μm proportionally decreased the amount of deposit, and the diamond-like-carbon, CrN, and NiCr–CrC composite coatings effectively hindered the fouling process. This study provides fundamental insights into the MSW fouling and proof-of-concept of potential mitigations through the screw surface modification.

09 BIOMASS FUELS↗
DOE OSTI2025

Scalable thin graphene oxide membranes enabled by polydopamine gutter layer

Two-dimensional (2D) nanosheets have been widely used to fabricate thin-film composite membranes for dye desalination. However, they often need to be thick to mitigate the defects resulting from their random stacking and rough support surface. Herein, bio-adhesive polydopamine (PDA) is used as a gutter layer to prepare graphene oxide (GO)-based membranes by improving the adhesion between the GO and porous support and providing a smooth surface to form thin, highly selective layers. For example, the PDA priming reduces the GO layer thickness by 57 %, from 447 to 190 nm, while achieving similar dye desalination properties. The effect of the dopamine concentration, exposure time, and GO layer thickness on the membrane structure and desalination performance are thoroughly investigated using various techniques, such as scanning electron microscopy (SEM), x-ray photoelectron spectroscopy (XPS), and x-ray diffraction (XRD). The PDA gutter layer is also applied for hollow fiber membranes, achieving water permeance of 79 L m -2 h −1 bar−1 and rejection of ∼99 % for Direct red 80. The membranes were challenged by simulated dye/salt mixtures to elucidate the complicated effect of the compositions on the desalination performance. Furthermore, this study unveils a new avenue to improve separation performance and large-scale manufacturability of 2D material-based membranes.

Dye desalination↗
DOE OSTI2025

A critical verification of beam and shell models of wind turbine blades

Ever-increasing wind turbine size has challenged predictive capabilities on several fronts. Here, to address part of the blade structural modeling uncertainty, a systematic model fidelity comparison study was conducted on commonly used finite elements. pyNuMAD was utilized to create beam, shell, and solid models of a 100 m long blade undergoing large static deflections. The solid model avoided the use of layered-solid elements by resolving core and facesheet layers. An unprecedented model with 73.7 million elements revealed insights that have never been possible from prior experimental and numerical studies. As compared to the solid element model, the tip deflection from the shell and beam model was found to be about 2% and 4.3% too low, respectively. The twist from the beam model was found to be about 5.6% too high, while the twist from shell model was 24% too low, though improvement was demonstrated with mesh refinement. The beam model adhesive stresses were more accurate than the shell model. Out-of-plane stresses were of great significance near geometric and material discontinuities, and neither the shell nor beam model captured these effects well. Failure predictions from beam, shell, or layered-solid models are unlikely to be reliable at trailing edges, adhesives, ply-drops, spar-cap boundaries.

17 WIND ENERGY↗
DOE OSTI2024

The Effect of Air Separations on Fast Pyrolysis Products for Forest Residue Feedstocks

This study investigates the intricate relationship between biomass preprocessing and pyrolysis product yields, employing the air classification technique for the treatment of loblolly pine residues with varying moisture content. A comprehensive exploration of the physicochemical properties of air-classified loblolly pine informs a sophisticated pyrolysis simulation model. Given the complex and multifaceted nature of biomass pyrolysis, operating across diverse temporal and spatial scales, a pyrolysis kinetics-based CFD–DEM simulation method is employed to predict product yields. Results showed that the elevated moisture content amplifies particle adhesiveness, necessitating augmented air velocities for effective separation, thereby influencing the efficiency of the separation process. While carbon and hydrogen contents exhibit relative stability across diverse moisture contents and blower frequencies, the oxygen content undergoes noticeable changes. For example, the oxygen contents were measured as 29.2 and 38.6 wt% in the light fraction of 30% moisture content sample at blower frequencies of 10 and 20 Hz, respectively. An intriguing finding emerges from pyrolysis simulation, indicating that a lower blower frequency in air classification moderately enhances bio-oil yield and significantly improves its quality, particularly in terms of water content. For instance, the water content in the bio-oil was about 1.5% and 10% in the heavy and light fractions, respectively from 10% moisture sample under 15 Hz blower frequency. In summary, a detailed understanding and strategic manipulation of critical material attributes in biomass through efficient fractionation techniques are imperative for advancing fast pyrolysis as a sustainable avenue for renewable energy and chemical production.

09 BIOMASS FUELS↗
DOE OSTI2026

Minimized aging of isocyanurate-based rigid cellular foams for buildings through tailored barrier facers and optimized formulation

The thermal resistivity (h·ft 2 ·°F/Btu/in.) of closed-cell rigid foam insulation materials significantly decreases over time. Diffusion-tight facers are designed to significantly enhance initial thermal resistivity and long-term thermal performance by preventing gas diffusion into the foam cells and inhibiting the escape of low thermal conductivity blowing agents. In addition to the gas diffusion property of the facer film, adhesion between the foam and the facer is crucial for achieving diffusion-tight bonding. Here, this study addresses the challenge of thermal aging by investigating how facer film properties and foam formulation influence the durability of thermal performance. A systematic evaluation was conducted to understand the effects of polymeric barrier films, surface treatments, facer coverage, and foam matrix rigidity on thermal resistivity over time. Key findings reveal that diffusion-tight facers, particularly those with metallized layers and compatible heat seal layers, significantly reduce gas exchange and improve foam-facer adhesion. The optimized system, incorporating barrier facers and a tailored polyisocyanurate foam formulation, achieved initial and aged thermal resistivity values after 200 days of approximately 8.3 and 7.4 h ft 2 ·°F/Btu/in., respectively representing only a 10 % reduction compared to a 17 % reduction observed in control samples without facers. Notably, polyurethane spray foams with facers exhibited only a 4 % reduction in thermal resistivity, compared to a 23 % decrease in control samples, demonstrating nearly six times better retention of thermal performance. This innovative facer technology presents a promising solution for reducing energy costs and represents a significant advancement in optimizing energy management for building envelopes in future technologies. This technology can also be adapted for other applications that necessitate the preservation of long-term thermal performance.

Wanasinghe, Shiwanka Vidarshi [Oak Ridge National ↗
DOE OSTI2025

High tensile alloy of copper to mitigate current collector deformation in silicon electrodes for lithium-ion batteries

The volumetric changes of silicon electrodes, along with the strong adhesive properties of certain binders, can lead to plastic deformation of the current collector and create damage in the electrode coating. Here, in this study, we report a detailed study of silicon coatings on a high-tensile alloy (HTA) foil of copper with strength over twice that of conventional copper foils. The HTA current collectors with high mechanical strength can mitigate plastic deformation upon continuous cycling. At moderate areal capacities (2.5–3 mAh cm −2 ), conventional copper foils show significant wrinkling after only a few electrochemical cycles, whereas the HTA foils remain intact. We demonstrate viability of the HTA foils in large format xx6395 pouch cells, in which the HTA current collectors remain intact even at an areal capacity of 4.5 mAh cm −2 ; in contrast, wrinkles form in conventional copper current collectors increasing the likelihood of lithium plating. Computational studies show that stresses generated during cycling of silicon electrodes are very high in the current collector and at the current collector-coating interface, explaining the wrinkling of conventional Cu foils. Our studies highlight importance of current collector to solve the electrochemical and chemo-mechanical performance challenges associated with high-loading silicon electrodes.

Chemo-mechanical degradation↗
DOE OSTI2026

3D Tomography insights on particle-particle bonding in cold spray

The conditions of the target surface during cold spray affect deformation and bonding. While surface preparation can influence the adhesion of the first particles, such modification is not relevant to the particle-particle interfaces that dominate the growth of a coating. Here we study two-particle Cu stacks produced with a single-particle launch apparatus and compare them to single-particle experiments on a clean polished substrate. Serial cross-sectioning using microtomography permits a systematic evaluation and quantification of bonding at the particle-particle interfaces. We observe that the top particle in the two-particle stacks is much more flattened compared to single impacts on the polished substrate. Although the resulting interfacial area expansion is comparable to that of single impacts at the same velocities, bonding at the particle-particle interfaces is significantly less (never exceeding 18% even around the “optimal” velocity for bonding). Lastly, we find that hydrodynamic jetting, a form of localization known to promote adhesion in cold spray, is hindered for impacts on top of a prior particle deposition. Here, the results point to a need for future studies that separately consider topography and mechanical properties of substrates in the pursuit of optimal bonding.

Bonding↗
DOE OSTI2025

Sustainable, degradable and malleable low-dielectric-constant thermosets derived from biomass for recyclable green electronics

In view of their excellent thermal and chemical resistance, favorable adhesion properties, high tensile strength, and other advantages, epoxy thermosets have numerous industrial applications such as coating, adhesive, and composite material production. However, bisphenol A (BPA)-based resins, which account for a significant fraction of the above thermosets, adversely affect human health by interfering with the normal functioning of the endocrine system and cannot be easily decomposed and recycled. Herein, degradable and sustainable bio-based epoxy thermosets with crosslinked network structures are prepared by the epoxidation of isosorbide with epichlorohydrin and the curing of the produced isosorbide diglycidyl ether (ISDGE) with cyclic lactones through a cationic ring-opening reaction. The ISDGE thermosets fully decompose into soluble and recyclable products under mildly basic conditions within three days, which is ascribed to the presence of ester moieties within the polymer network structure. Compared to a representative BPA-based epoxy, ISDGE-based thermosets exhibit lower dielectric constants and are more flexible. Moreover, the glass fibers in ISDGE-based prepregs can be fully recovered after on-demand degradation. Furthermore, our work provides promising eco-friendly alternatives to conventional epoxy thermosets and paves the way for the reduction of plastic waste generation and the development of recyclable green electronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

In situ characterization of metastable Pb3O5 and Pb2O3 phases during thermal decomposition of PbO2 to PbO

Nonstoichiometric lead oxides play a key role in the formation and cycling of the positive electrodes in a lead acid battery. These phases have been linked to the underutilization of the positive active material but also play a key role in the battery’s cycle life, providing inter-particle adhesion and the connection to the underlying lead grid. Similar phases have previously been identified by mass loss or color change during thermal annealing of PbO2 to PbO, suggesting that at least two intermediate PbOx phases exist. Using multiple in situ analysis techniques (powder diffraction, x-ray absorption, x-ray photoelectron spectroscopy) and ex situ nuclear magnetic resonance measurements, the structural conversion and changes in the lead oxidation states were identified during this process. Isolation of the PbOx phases enabled confirmation of Pb3O5 and Pb2O3 by diffraction and the first 207Pb NMR measurement of these intermediates.

Kinnibrugh, Tiffany L.↗
DOE OSTI2025

Impact of Hydroxyl Functionalization and Unsaturation on Linear Poly(ethylene- co -vinyl alcohol)

Functionalization of C═C in unsaturated polyolefins by hydroboration/oxidation successfully generates linear poly(ethylene-co-vinyl alcohol) (LEVOH) polymers. This postpolymerization modification expands upon previously reported chemistry to control the extent of functionalization through reagent stoichiometry. Partial functionalization (24–92% of C═C) of polycyclooctene produces materials with both C═C in the backbone and pendant OH and subsequent hydrogenation generate a LEVOH. We explore the thermal, structural, surface, and adhesive properties of these LEVOH and the partially unsaturated intermediate and find they are impacted by both the extent of OH incorporation and saturation. The presence of C═C significantly reduces the melting temperature and crystallinity while increasing surface polarity and adhesive strength compared with saturated polymers at equivalent functionalization. Furthermore, this investigation demonstrates linear analogs of EVOH with a wide range of properties tuned by extent of hydroxylation and presence of unsaturation.

Crystal structure↗
DOE OSTI2025

Polyhalohydrins: Investigating Vicinal Functionalities by Ring-Opening of Epoxides on Polyolefins

Halohydrins are functional groups that are underexplored in polymer science. This study synthesized and examined structure–property relationships of halohydrin-functionalized polymers derived from polycyclooctene (PCOE), which was obtained via ring-opening metathesis polymerization (ROMP). The polyhalohydrins, including polychlorohydrin, polybromohydrin, and polyiodohydrin, were produced through a two-step process involving epoxidation of PCOE followed by epoxide ring-opening using hydrochloric, hydrobromic, or hydroiodic acid. These stereoirregular and regioirregular polymers are amorphous as measured by differential scanning calorimetry and X-ray scattering. Lap joint shear testing revealed an enhanced adhesive performance in polychlorohydrin and polybromohydrin, with the former demonstrating nearly three times the ultimate shear stress compared to a model polyethylene, hydrogenated PCOE. Additionally, contact angle measurements and surface free energy analysis showed an increase in hydrophilicity and polarity from iodine- to bromine- to chlorine-functionalized polyhalohydrins, aligning with trends in adhesion strength. Furthermore, these results underscore the potential of halohydrin functionalization as a versatile approach for tuning surface properties, offering new opportunities for polymer-to-polymer transformations.

Functional groups↗
DOE OSTI2024

Designing metal halide perovskite solar modules for thermomechanical reliability

There is a significant deficiency in perovskite solar module (PSM) stability under thermomechanical stressors which is not well-understood. In this perspective, common issues seen with perovskite solar cell device fabrication related to thermomechanical reliability of PSM processing are discussed, with a focus on how the robustness of device layers and interlayer adhesion can be improved. Film stresses, adhesion of charge transport layers, and instability under light and heat are discussed with the purpose of providing insight on designing PSMs for durability. Processing conditions of encapsulation of PSMs and critical parameters to consider are also examined, and accelerated testing protocols for PSMs are discussed that probe mechanical degradation modes and ensure reliability of devices in the field.

14 SOLAR ENERGY↗
DOE OSTI2024

Tough and circular glass fiber composites via a tailored dynamic boronic ester interface

Glass fiber reinforced polymer (GFRP) composites are valued for their strength and cost-effectiveness. However, traditional GFRPs often face challenges for end-of-life recycling due to their non-depolymerizable thermoset matrices, and long-term performance due to inadequate interfacial adhesion, which can lead to fiber–matrix delamination. Here, in this work, we have designed dynamic fiber–matrix interfaces to allow tough and closed-loop recyclable GFRPs by utilizing a vitrimer, derived from upcycled polystyrene-b-poly(ethylene-co-butylene)-b-polystyrene (SEBS) with boronic ester (S-Bpin) and amine-based diol crosslinker. The boronic ester groups in S-Bpin form dynamic covalent bonds with the naturally present hydroxyl groups on the unsized GF surface, which eliminates the need for fiber sizing and enables facile closed-loop recyclability of both the fibers and the vitrimer matrix. The resulting strong fiber–matrix interface, depicted by the Raman mapping, leads to a 552% increase in-plane shear toughness (6.2 ± 0.3 MJ m -3 ) and 27% ultimate tensile strength (361 ± 89.2 MPa) compared to those of the conventional epoxy-based matrix (0.95 ± 0.05 MJ m -3 and 264 ± 59.7 MPa, respectively). The network rearrangement through dynamic boronic ester exchange enables fast thermoformability and repairability of micro-cracks at elevated temperatures. Additionally, both the matrix and composite demonstrate strong adhesion to various surfaces including steel and glasses exhibiting ≥6 MPa lap shear strength, which expands their suitability for diverse industrial applications. The readily created dynamic interface between boronic ester functionalized vitrimer and neat GFs presents a promising strategy for developing closed-loop recyclable, multifunctional structural materials, offering a sustainable alternative to non-recyclable thermoset GFRPs and contributes to a circular economy in composite materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Critical role of oxide anchoring groups in organic electron transport layers for perovskite solar cell stability

Charge transport layers (CTLs) play a critical role in the performance and long-term stability of perovskite solar cells (PSCs) by facilitating efficient charge extraction and providing interfacial stabilization. For organic CTLs, different functional groups have been designed to modulate the interactions with the substrate. Anchoring groups are used to establish strong adhesion to transparent conductive oxides (TCOs) but are not routinely incorporated in organic CTL design. In this study, we investigate the influence of anchoring groups in organic electron transport layers (ETLs) on PSC performance and stability by synthesizing and evaluating two naphthalene diimide (NDI)-based ETLs: NDI-(PhPA) 2 , functionalized with polar phenyl phosphonic acid (PhPA) groups, and NDI-(PhBr) 2 , modified with nonpolar bromophenyl (PhBr) groups. X-ray photoelectron spectroscopy confirms that PhPA functionalization leads to NDIs anchored onto fluorine-doped tin oxide (FTO) following chemical bath deposition, while NDI-(PhBr) 2 shows no detectable surface presence after deposition. We show that NDI-(PhPA) 2 deposits as a thin film on FTO, exhibiting strong adhesion, high solvent resistance, and enhanced light and thermal stability, achieving a maximum device efficiency of 14.3%. Stability assessments conducted under continuous illumination at 25 °C for 200 hours and at 65 °C for 100 hours demonstrate performance on par with TiO 2 -based ETLs. In contrast, NDI-(PhBr) 2 , which lacks strong anchoring interactions, fails to adhere to the FTO surface, resulting in a rapid decrease in efficiency over a few hours, comparable to devices without an ETL. These findings highlight the importance of anchoring groups in organic CTLs for achieving long-term PSC stability under operational conditions.

Kim, Sanggyun [Georgia Institute of Technology, At↗
DOE OSTI2026

Multiphasic droplet microfluidics platform for controlled bacteria and mammalian cell co-culture

Microfluidics has revolutionized high-throughput miniaturized biological assays. However, co-culture of mammalian cells and bacteria remains challenging in microfluidic systems due to incompatible growth requirements, limited spatial control, and the requirement for a mammalian cell adhesion matrix. Here, we present a microfluidic platform that generates multiphasic droplets which encapsulate mammalian and bacterial cells, enabling their direct and indirect co-culture. By combining photopolymerizable hydrogels with polymer phase separation, we generate core–shell droplets composed of a liquid and a hydrogel compartment. The hydrogel compartment supports mammalian cell adhesion and culture, while the liquid compartment sustains bacterial growth. We demonstrate two droplet architectures that allow physical bacteria–mammalian cell contacts or enforce complete physical separation, representing direct and indirect co-culture. Our multiphasic droplets are stable, customizable, able to sustain co-culture for over 24 hours, and compatible with fluorescence-based cell sorting technologies. Overall, our multiphasic droplet microfluidic platform provides a scalable and versatile tool for high-throughput co-culture and screening of host–microbe interactions.

59 BASIC BIOLOGICAL SCIENCES↗