Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRPLANES - CHARACTERISTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Calculated Drag of an Aerial Refueling Assembly Through Airplane Performance Analysis

The aerodynamic drag of an aerial refueling assembly was calculated during the Automated Aerial Refueling project at the NASA Dryden Flight Research Center. An F/A-18A airplane was specially instrumented to obtain accurate fuel flow measurements and to determine engine thrust. A standard Navy air refueling store with a retractable refueling hose and paradrogue was mounted to the centerline pylon of the F/A-18A airplane. As the paradrogue assembly was deployed and stowed, changes in the calculated thrust of the airplane occurred and were equated to changes in vehicle drag. These drag changes were attributable to the drag of the paradrogue assembly. The drag of the paradrogue assembly was determined to range from 200 to 450 lbf at airspeeds from 170 to 250 KIAS. Analysis of the drag data resulted in a single drag coefficient of 0.0056 for the paradrogue assembly that adequately matched the calculated drag for all flight conditions. The drag relief provided to the tanker airplane when a receiver airplane engaged the paradrogue is also documented from 35 to 270 lbf at the various flight conditions tested. The results support the development of accurate aerodynamic models to be used in refueling simulations and control laws for fully autonomous refueling.

Vachon, Michael Jacob↗

Ditching Tests with a 1/16-Size Model of the Navy XP2V-1 Airplane at the Langley Tank No. 2 Monorail

Tests were made with a 1/16 size dynamically similar model of the Navy XP2V-1 airplane to study its performance when ditched. The model was ditched in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and conditions of damage were simulated. The performance of the node1 was determined and recorded from visual observations, by recording time histories of the longitudinal decelerations, and by taking motion pictures of the ditchings From the results of the tests with the model the following conclusions were drawn: 1. The airplane should be ditched at the normal landing attitude. The flaps should be fully extended to obtain the lowest possible landing speed; 2. Extensive damage will occur in a ditching and the airplane probably will dive violently after a run of about 2 fuselage lengths. Maximum longitudinal decelerations up to about 4g will be encountered; and 3. If a trapezoidal hydroflap 4 feet by 2 feet by 1 foot is attached to the airplane at station 192.4, diving will be prevented and the airplane will probably porpoise in a run of about 4 fuselage lengths with a maximum longitudinal deceleration of less than 3.5g.

Fisher, Lloyd J.↗

Gust-Tunnel Investigation to Determine the Load at the Joint of a Coupled Airplane Configuration Encountering a Gust

An investigation has been made in the Langley gust tunnel with two identical airplane models approximating 1/40-scale models of the B-29, coupled in tandem with a boom so that the individual centers of gravity were equidistant from the single coupling joint at the tail of the lead airplane. Time histories of the boom joint load were obtained as the models were flown through a gust. The results indicate that on a similar configuration involving airplanes the size of B-29 airplanes a load on the boom joint of 10,000 to 14,000 pounds could be induced by encountering a gust of 50 feet per second and having a gradient distance of 17 chords, at a forward speed of 380 feet per second and that the total load is extremely sensitive to the steadiness of flight that can be maintained with or without a gust. It is felt that the results are probably satisfactory to show order of magnitude, but it does not appear possible that a precise determination of the joint load that would be applicable to the full-scale airplanes can be obtained by gust-tunnel tests.

Cahen, George L.↗

Directional Stability of Towed Airplanes

So far, very careful investigations have been made regarding the flight properties, in particular the static and dynamic stability, of engine-propelled aircraft and of untowed gliders. In contrast, almost no investigations exist regarding the stability of airplanes towed by a towline. Thus, the following report will aim at investigating the directional stability of the towed airplane and, particularly, at determining what parameters of the flight attitude and what configuration properties affect the stability. The most important parameters of the flight attitude are the dynamic pressure, the aerodynamic coefficients of the flight attitude, and the climbing angle. Among the configuration properties, the following exert the greatest influence on the stability: the tow-cable length, the tow-cable attachment point, the ratio of the wing loadings of the towing and the towed airplanes, the moments of inertia, and the wing dihedral of the towed airplane. In addition, the size and shape of the towed airplane vertical tail, the vertical tail length, and the fuselage configuration are decisive factors in determining the yawing moment and side force due to sideslip, respectively.

Soehne, W.↗

Spin Tests of 1/20-Scale Models of the Chance Vought Revised XF6U-1 and F6U-1 Airplanes, TED No. NACA 2390

An investigation has been conducted in the Langley 20-foot free-spinning tunnel on the 1/20-scale model of the Chance Vought XF6U-1 airplane altered to represent the XF6U-1 airplane as it will be spin-tested in flight, and also altered to represent the F6U-1 airplane as it will be produced for service use. Spin tests were made to determine the effects of control settings and movements at the normal loading. The results show that the spins obtained on the revised XF6U-1 airplane will be oscillatory in roll and yaw and that recoveries by rudder reversal will be rapid. Model test results indicate that the F6U-1 airplane will probably not spin. Inasmuch as the results of this investigation show that the new designs are as good as or better than the original XF6U-1 design in regard to spin recovery, it is felt that the conclusions and recommendations reached for the original design can be applied to the new designs for all loading conditions.

Klinar, Walter J.↗

Planetary Airplane Extraction System Development and Subscale Testing

The Aerial Regional-scale Environmental Survey (ARES) project employs an airplane as the science platform from which to collect science data in the previously inaccessible, thin atmosphere of Mars. In order for the airplane to arrive safely in the Martian atmosphere a number of sequences must occur. A critical element in the entry sequence at Mars is an extraction maneuver to separate the airplane quickly (in less than a second) from its protective backshell to reduce the possibility of re-contact, potentially leading to mission failure. This paper describes the development, testing, and lessons learned from building a 1/3 scale model of this airplane extraction system. This design, based on the successful Mars Exploration Rover (MER) extraction mechanism, employs a series of trucks rolling along tracks located on the surface of the central parachute can. Numerous tests using high speed video were conducted at the Langley Research Center (LaRC) to validate this concept. One area of concern was that that although the airplane released cleanly, a pitching moment could be introduced. While targeted for a Mars mission, this concept will enable environmental surveys by aircraft in other planetary bodies with a sensible atmosphere such as Venus or Saturn s moon, Titan.

Teter, John E., Jr.↗

Planetary Airplane Extraction System Development and Subscale Testing

The Aerial Regional-scale Environmental Survey (ARES) project will employ an airplane as the science platform from which to collect science data in the previously inaccessible, thin atmosphere of Mars. In order for the airplane to arrive safely in the Martian atmosphere, a number of sequences must occur. A critical element in the entry sequence at Mars is an extraction maneuver to separate the airplane quickly (in less than a second) from its protective backshell to reduce the possibility of re-contact, potentially leading to mission failure. This paper describes the development, testing, and lessons learned from building a 1/3 scale model of this airplane extraction system. This design, based on the successful Mars Exploration Rover (MER) extraction mechanism, employs a series of trucks rolling along tracks located on the surface of the central parachute can. Numerous tests using high speed video were conducted at the Langley Research Center to validate this concept. One area of concern was that that although the airplane released cleanly, a pitching moment could be introduced. While targeted for a Mars mission, this concept will enable environmental surveys by aircraft in other planetary bodies with a sensible atmosphere such as Venus or Saturn's moon, Titan.

Teter, John E., Jr.↗

Airplane takeoff and landing performance monitoring system

The invention is a real-time takeoff and landing performance monitoring system for an aircraft which provides a pilot with graphic and metric information to assist in decisions related to achieving rotation speed (V.sub.R) within the safe zone of a runway, or stopping the aircraft on the runway after landing or take-off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane acceleration and engine-performance anomalies are detected and annunciated. A novel and important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in head wind occurring as the takeoff roll progresses. The system provides a head-down display and a head-up display. The head-up display is projected onto a partially reflective transparent surface through which the pilot views the runway. By comparing the present performance of the airplane with a continually predicted nominal performance based upon given conditions, performance deficiencies are detected by the system and conveyed to pilot in form of both elemental information and integrated information.

Middleton, David B.↗

Airplane takeoff and landing performance monitoring system

The invention is a real-time takeoff and landing performance monitoring system for an aircraft which provides a pilot with graphic and metric information to assist in decisions related to achieving rotation speed (V.sub.R) within the safe zone of a runway, or stopping the aircraft on the runway after landing or take-off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane and engine performance deficiencies are detected and annunciated. A novel and important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in head wind occurring as the takeoff roll progresses. The system provides a head-down display and a head-up display. The head-up display is projected onto a partially reflective transparent surface through which the pilot views the runway. By comparing the present performance of the airplane with a predicted nominal performance based upon given conditions, performance deficiencies are detected by the system.

Middleton, David B.↗

Estimated Effect of Ring Cowl on the Climb and Ceiling of an Airplane, Special Report

Although the application of a ring cowl to an airplane with an air-cooled engine increases the maximum L/D and the high speed to an appreciable extent, the performance in climb and ceiling is not increased as much as one would expect without analyzing the conditions. When a ring cowl is installed on an airplane, the propeller is set at a higher pitch to allow the engine to turn its rated r.p.m. at the increased high speed. V/nD is increased and the propeller efficiency at high speed is increased slightly. The ratio of r.p.m. at climbing speed, V(sub c) , to the r.p.m. at maximum speed, V (sub m) is dependent upon the ratio of V(sub c) to V(sub m). The increase in V(sub c) for all airplane with ring cowl i s not as great as the increase in V(sub m), so that the ratio V(sub c)/V(sub m) is less than for the airplane without ring. Consequently the r.p.m. and full throttle thrust power available are less at V(sub c) for the airplane with ring cowl and in spite of the increase in L/D due to the installation of the ring, the excess thrust power available for climbing is not appreciably changed. The same method of reasoning accounts for the small increase in absolute ceiling in spite of a large increase in L/D maximum.

Louden, F. A.↗

Radiated Emissions from a Remote-Controlled Airplane-Measured in a Reverberation Chamber

A full-vehicle, subscale all-electric model airplane was tested for radiated emissions, using a reverberation chamber. The mission of the NASA model airplane is to test in-flight airframe damage diagnosis and battery prognosis algorithms, and provide experimental data for other aviation safety research. Subscale model airplanes are economical experimental tools, but assembling their systems from hobbyist and low-cost components may lead to unforseen electromagnetic compatibility problems. This report provides a guide for accommodating the on-board radio systems, so that all model airplane systems may be operated during radiated emission testing. Radiated emission data are provided for on-board systems being operated separately and together, so that potential interferors can be isolated and mitigated. The report concludes with recommendations for EMI/EMC best practices for subscale model airplanes and airships used for research.

Ely, Jay J.↗

Prolonging Microgravity on Parabolic Airplane Flights

Three techniques have been proposed to prolong the intervals of time available for microgravity experiments aboard airplanes flown along parabolic trajectories. Typically, a pilot strives to keep an airplane on such a trajectory during a nominal time interval as long as 25 seconds, and an experimental apparatus is released to float freely in the airplane cabin to take advantage of the microgravitational environment of the trajectory for as long as possible. It is usually not possible to maintain effective microgravity during the entire nominal time interval because random aerodynamic forces and fluctuations in pilot control inputs cause the airplane to deviate slightly from a perfect parabolic trajectory, such that the freely floating apparatus bumps into the ceiling, floor, or a wall of the airplane before the completion of the parabola.

Robinson, David W.↗

CASPEr: an Approach to Characterize the Performance of Onboard Airplane Energy State and Automation Mode Prediction Functions

The Commercial Aviation Safety Team (CAST) has identified a set of safety enhancements to mitigate the risks of loss of control in-flight (LOCI) accidents and incidents involving commercial transport airplanes. In support of this, NASA has been developing technologies intended to enhance flight crew awareness of airplane systems, attitude, and energy state. This report describes preliminary ideas for a methodology to assess the goodness of onboard airplane energy state and automation mode prediction functions. The methodology is intended to contribute to the goal of moving these prediction technologies to the readiness level required for transition to industry and reduce the technology certification risks. In addition, this report describes a simulation-based approach named CASPEr (Characterization of Airplane State Prediction Error) to characterize the performance of these predictive functions over a wide range of operational conditions. The first exploratory version of this approach is described. The bulk of the report documents the initial results of tests to characterize the performance of an airplane trajectory prediction function. Future reports will give additional performance characterization results for this function and a complete description of the proposed methodology to assess such functions.

Torres-Pomales, Wilfredo↗

High-Altitude ADS-B Flight Tests on a NASA ER-2 Research Airplane

Researchers at the National Aeronautics and Space Administration (NASA) Armstrong Flight Research Center (Edwards, California); the Federal Aviation Administration (FAA); and Regulus Group, LLC (Atlantic City, New Jersey) collaborated for the flight-test demonstration of an Automatic Dependent Surveillance-Broadcast (ADS-B) system equipped on a high-altitude Earth Resources-2 (ER-2) research airplane. The unique ER-2 airplane is a NASA-owned and operated airborne science version of the United States Air Force / Lockheed Martin Aeronautics (Bethesda, Maryland) U-2S airplane. The FAA has mandated that by the year 2020, aircraft operating within certain sections of the United States National Airspace system be equipped with ADS-B Out technology; the research presented in this paper is the first to show how the NASA ADS-B architecture satisfies the mandate for a unique high-altitude aircraft. An exceptional military aircraft design, security protocols, and the performance envelope of the ER-2 airplane made the avionics integration remarkably challenging. The design required the ADS-B avionics to survive the harsh flight environment of the ER-2 airplane. The most prominent challenge was the functional integration of modern civilian avionics into federated military legacy avionics. Flight-test objectives were to certify an ADS-B Out (1090ES) passive surveillance integrated with a Traffic Alert and Collision Avoidance System (TCAS) I active surveillance system on an ER-2 platform for high-altitude cruise operations. In April 2022, NASA conducted three flights at Edwards Air Force Base (Edwards, California) - each greater than one-hour flight reaching altitudes above 60,000 ft.

ADS-B↗

High-Altitude ADS-B/GPS LPV Flight Tests on a NASA ER-2 Research Airplane

The research presented in this paper describes the conceptual design of a system architecture that integrates Automatic Dependent Surveillance-Broadcast (ADS-B) and Global Positioning System (GPS) Localizer Performance Vertical (LPV) guidance technology onto a unique high-altitude research airplane: a United States Air Force (USAF) / Lockheed Martin (Bethesda, Maryland) Aeronautics U-2S airplane. The design features modern display capabilities to provide air-to-air surveillance and precision navigation, to adhere to Federal Aviation Administration (FAA) certification standards for operations in upper Class E airspace. The National Aeronautics and Space Administration (NASA) variant of the U-2S, now called the Earth Resources (ER-2) airplane, remains unrivaled in the art of sustained high-altitude flight for scientific expeditions. Capable of routinely cruising above flight level (FL) 650 that had been considered, at inception, the domain of only the most elite experimental research aircraft types. Nicknamed the Dragon Lady, this U-2S research testbed is still one of the most advanced aircraft in the world. The exceptional military design of the vehicle, security guidelines, and the performance envelope of the ER-2 posed unique challenges to the integration of modern civilian avionics. ADS-B epitomizes the next generation of surveillance technology, incorporating both air and ground aspects. ADS-B provides air traffic control (ATC) with a more accurate picture of the three-dimensional positioning of aircraft in various phases of flight, including en route, terminal, approach, and ground operations. The airborne surveillance system broadcasts its identification, position, altitude, velocity, and other information. GPS LPV represents a significant advancement in aviation technology, emphasizing the pivotal role that GPS and Performance-Based Navigation concepts will play in the foreseeable future. This technology represents a shift from sensor-based navigation to performance-based navigation, allowing for more flexible and efficient use of airspace. This research described herein is structured as follows: Section II, “Systems Background,” provides a systems background and description of an ADS-B and GPS LPV system equipped on the high-altitude ER-2 research airplane to satisfy the FAA airworthiness requirements for high-altitude flight operations. Section III, “Flight Test System,” describes the flight-test airplane systems. Section IV, “Analysis of GPS SBAS, Safety, and Ground Tests,” provides an overview of the GPS Satellite-Based Augmentation System (SBAS) and an analysis of the GPS LPV metrics, safety, and ground tests. Section V, “High-Altitude Flight Tests,” describes the high-altitude flight tests, including 3 flight-test results, analysis, human factors, and lessons learned. Section VI, the conclusion, draws insights from the lessons learned, discusses the design challenges associated with ADS-B and GPS LPV, and showcases the paramount significance of these pivotal technologies in aircraft surveillance and navigation.

Ricardo A. Arteaga↗

AVIATR - Aerial Vehicle for In-situ and Airborne Titan Reconnaissance A Titan Airplane Mission Concept

We describe a mission concept for a stand-alone Titan airplane mission: Aerial Vehicle for In-situ and Airborne Titan Reconnaissance (AVIATR). With independent delivery and direct-to-Earth communications, AVIATR could contribute to Titan science either alone or as part of a sustained Titan Exploration Program. As a focused mission, AVIATR as we have envisioned it would concentrate on the science that an airplane can do best: exploration of Titan's global diversity. We focus on surface geology/hydrology and lower-atmospheric structure and dynamics. With a carefully chosen set of seven instruments-2 near-IR cameras, 1 near-IR spectrometer, a RADAR altimeter, an atmospheric structure suite, a haze sensor, and a raindrop detector-AVIATR could accomplish a significant subset of the scientific objectives of the aerial element of flagship studies. The AVIATR spacecraft stack is composed of a Space Vehicle (SV) for cruise, an Entry Vehicle (EV) for entry and descent, and the Air Vehicle (AV) to fly in Titan's atmosphere. Using an Earth-Jupiter gravity assist trajectory delivers the spacecraft to Titan in 7.5 years, after which the AVIATR AV would operate for a 1-Earth-year nominal mission. We propose a novel 'gravity battery' climb-then-glide strategy to store energy for optimal use during telecommunications sessions. We would optimize our science by using the flexibility of the airplane platform, generating context data and stereo pairs by flying and banking the AV instead of using gimbaled cameras. AVIATR would climb up to 14 km altitude and descend down to 3.5 km altitude once per Earth day, allowing for repeated atmospheric structure and wind measurements all over the globe. An initial Team-X run at JPL priced the AVIATR mission at FY10 $715M based on the rules stipulated in the recent Discovery announcement of opportunity. Hence we find that a standalone Titan airplane mission can achieve important science building on Cassini's discoveries and can likely do so within a New Frontiers budget.

UAV↗

Study of stability of large maneuvers of airplanes

A predictive method of nonlinear system analysis is used to investigate airplane stability and dynamic response during rolling maneuvers. The maneuver roll-rate is not assumed to be constant, and the airplane motion is represented by a set of coupled nonlinear differential equations. The general rolling maneuver is kinematically specified by its roll-rate variation p(t). A method for relating the airplane dynamic response to p(t) is developed. The method provides analytical expressions for the motion variables in terms of the maneuver descriptor p(t). A parameterized family of rolling maneuvers is considered, for which the method is used to predict specific dynamic response information, such as the dependence of the peak angle-of-attack excursion on the maneuver parameters. The stability and motion of the airplane in response to an arbitrary actuation of aileron input is considered. Analytical expressions relating motion variables to aileron input are obtained. Explicit analytical bounds on the motion variables are derived. A stability criterion which guarantees nondivergence of motion in response to aileron actuation is presented.

Haddad, E. K.↗

Measurements of sonic booms generated by an airplane flying at Mach 3.5 and 4.8

Sonic booms generated by the X-15 airplane flying at Mach numbers of 3.5 and 4.8 were measured. The experimental results agreed within 12 percent with results obtained from theoretical methods. No unusual phenomena related to overpressure were encountered. Scaled data from the X-15 airplane for Mach 4.8 agreed with data for an SR-71 airplane operating at lower Mach numbers and similar altitudes. The simple technique used to scale the data on the basis of airplane lift was satisfactory for comparing X-15 and SR-71 sonic boom signatures.

Green, K. S.↗