Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRPLANES - PERFORMANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

The FAA aging airplane program plan for transport aircraft

The FAA Aging Airplane Program is focused on five program areas: maintenance, transport airplanes, commuter airplanes, airplane engines, and research. These programs are complementary and concurrent, and have been in effect since 1988. The programs address the aging airplane challenge through different methods, including policies, procedures, and hardware development. Each program is carefully monitored and its progress tracked to ensure that the needs of the FAA, the industry, and the flying public are being met.

Aging Aircraft↗
NASA NTRS1993

Electric field measurements with an airplane - Problems caused by emitted charge

The temporal variation of electric field components deduced from measurements made with airplanes penetrating electrified clouds is often complex, especially when the airplane experiences strong electrical charging. However, unusually simple electric field variations were obtained for penetrations involving severe charging of an airplane on flights over Kennedy Space Center, Florida, on August 19, 1989. Analysis of these results suggests that plumes of ions were emitted from the airplane. The electric field from these plumes was more intense than the ambient field from the cloud at the location of the aft electric field sensor. As a consequence, the deduced component of the ambient electric field in the direction of flight was severely distorted. These findings emphasize (1) the importance of careful evaluation of electric field data obtained with airplanes and (2) the need for improved measurements.

Jones, J. J.↗
NASA NTRS1921

The Development of German Army Airplanes During the War

The author, who was a captain of the Reserves in the Technical Department of the Aviation Division (Board of Airplane Experts) during the war, shows what means were taken for the creation of new airplane types and what tests were employed for trying out their flying properties, capacities and structural reliability. The principal representative types of each of the classes of airplanes are described and the characteristics of the important structural parts are discussed. Data regarding the number of airplanes at the front and the flying efficiency of the various classes of airplanes are given.

Wilhelm, Hoff↗
NASA NTRS1923

Air resistance measurements on actual airplane parts

For the calculation of the parasite resistance of an airplane, a knowledge of the resistance of the individual structural and accessory parts is necessary. The most reliable basis for this is given by tests with actual airplane parts at airspeeds which occur in practice. The data given here relate to the landing gear of a Siemanms-Schuckert DI airplane; the landing gear of a 'Luftfahrzeug-Gesellschaft' airplane (type Roland Dlla); landing gear of a 'Flugzeugbau Friedrichshafen' G airplane; a machine gun, and the exhaust manifold of a 269 HP engine.

Weiselsberger, C↗
NASA NTRS1927

Method of Correcting Wind Tunnel Data for Omitted Parts of Airplane Models

Wind tunnel models do not have complete similarity to the full scale airplane. Part of the dissimilarity is due to the difference between the stationary model in the artificial wind stream of the tunnel and the moving airplane in still air. There are a number of other reasons for departing from exact geometrical similitude. For reasons of accuracy and economy, all minor parts of the full scale airplane, such as struts, wires, fittings, control horns and other parts whose scale corrections are large are removed from wind tunnel models. By omitting the minor parts of the airplane in the wind tunnel model and adding to the forces and moments of the model those omitted parts measured full scale and properly reduced, the scale effects of such parts disappear from the model data. Scale effects due to major parts of the airplane, particularly the fuselage and wings, can be corrected by omitting the propeller and making the surface of the model as smooth as possible, two further departures from geometrical similitude between model and full scale that add considerably to the accuracy and economy of model tests.

Smith, R H↗
NASA NTRS1938

Wind-tunnel Tests of a 2-engine Airplane Model as a Preliminary Study of Flight Conditions Arising on the Failure of the Engine

Wind tunnel tests of a 15-foot-span model of a two-engine low wing transport airplane were made as a preliminary study of the emergency arising from the failure of one engine in flight. Two methods of reducing the initial yawing moment resulting from the failure of one engine were investigated and the equilibrium conditions were explored for two basic modes on one engine, one with zero angle of sideslip and the other with several degrees of sideslip. The added drag resulting from the unsymmetrical attitudes required for flight on one engine was determined for the model airplane. The effects of the application of power upon the stability, controllability, lift, and drag of the model airplane were measured. A dynamic pressure survey of the propeller slipstream was made in the neighborhood of the tail surfaces at three angles of attack. The added parasite drag of the model airplane resulting from the unfavorable conditions of flight on one engine was estimated. From 35 to 50 percent of this added drag was due to the drag of the dead engine propeller and the other 50 to 65 percent was due to the unsymmetrical attitude of the airplane. The mode of flight on one engine in which the angle of sideslip was zero was found to require less power than the mode in which the angle of sideslip was several degrees.

Hartman, Edwin P↗
NASA NTRS1940

Measured moments of inertia of 32 airplanes

A compilation of the experimentally determined moments of inertia of 32 airplanes is presented. The measurements were obtained at the laboratories of the naca by means of a pendulum method. The airplanes tested are representative of several types of aircraft of gross weight less than 10,000 pounds. The results are presented in coefficient as well as in dimensional form. An elementary analysis of the data disclosed the possibility of grouping the results according to wing type of the airplane, as low-wing monoplanes, parasol and high-wing monoplanes, and biplanes. The data are shown to provide a convenient means of rapidly estimating the moments of inertia of other airplanes. A three view drawing of each of the 32 airplanes is included.

Gracey, William↗
NASA NTRS1954

A study of the application of power-spectral methods of generalized harmonic analysis to gust loads on airplanes

The applicability of some results from the theory of generalized harmonic analysis (or power-spectral analysis) to the analysis of gust loads on airplanes in continuous rough air is examined. The general relations for linear systems between power spectrums of a random input disturbance and an output response are used to relate the spectrum of airplane load in rough air to the spectrum of atmospheric gust velocity. The power spectrum of loads is shown to provide a measure of the load intensity in terms of the standard deviation (root mean square) of the load distribution for an airplane in flight through continuous rough air. For the case of a load output having a normal distribution, which appears from experimental evidence to apply to homogeneous rough air, the standard deviation is shown to describe the probability distribution of loads or the proportion of total time that the load has given values. Thus, for airplane in flight through homogeneous rough air, the probability distribution of loads may be determined from a power-spectral analysis. In order to illustrate the application of power-spectral analysis to gust-load analysis and to obtain an insight into the relations between loads and airplane gust-response characteristics, two selected series of calculations are presented. The results indicate that both methods of analysis yield results that are consistent to a first approximation.

Press, Harry↗
NASA NTRS1921

General Theory of the Steady Motion of an Airplane

The writer points out briefly the history of the method proposed for the study of steady motion of an airplane, which is different from other methods now used. M. Paul Painleve has shown how convenient the drag-lift curve was for the study of airplane steady motion. The author later added to the drift-lift curve the curve called the "speed curve" which permits a direct checking of the speed of the airplane under all flying conditions. But the speed curve was plotted in the same quadrant as the drag-lift curve. Later, with the progressive development of aeronautical science, and with the continually increasing knowledge concerning engines and propellers, the author was brought to add the three other quadrants to the original quadrant, and thus was obtained the steady motion chart which is described in detail in this report. This charts permits one to read directly for a given airplane its horizontal speed at any altitude, its rate of climb at any altitude, its apparent inclination to the horizon at any moment, its ceiling, its propeller thrust, revolutions, efficiency, and power absorbed, that is the complete set of quantities involved in the subject, and to follow the variations of all these quantities both for variable altitude and for variable throttle. The chart also permits one to follow the variation of all of the above in flight as a function of the lift coefficient and of the speed. The author also discusses the interaction of the airplane and propeller through the slipstream and the question of the properties of the engine-propeller system and its dependence upon the properties of the engine considered alone and of the propeller considered alone. There is also a discussion of a standard atmosphere.

De Bothezat, George↗
NASA NTRS1932

Maneuverability Investigation of the F6C-3 Airplane with Special Flight Instruments

This investigation was made for the purpose of obtaining information on the maneuverability of the F6C-3 airplane. It is the first of a series of similar investigations to be conducted on a number of military airplanes for the purpose of comparing the abilities of these airplanes to maneuver, and also to establish a fund of quantitative data which may be used in formulating standards of comparison for rating the maneuverability of any airplane. A large part of this initial investigation was necessarily devoted to the development and trial of methods suitable for use in subsequent investigations of this nature. Air speed, angular velocity, linear acceleration, and position of the control surfaces were measured by instruments in the airplane during loops, push-downs, pull-outs from dives, pull-ups from level flight, barrel rolls, and spins. The coordinates of flight paths were deduced from the data whenever possible, and were checked in some cases by the use of a camera obscura. The results are given in curves showing the variation of the measured quantities with respect to time, and maximum values are tabulated.

Dearborn, C H↗
NASA NTRS1941

An analysis of the stability of an airplane with free controls

Report presents the results of an investigation made of the essentials to the stability of an airplane with free control surfaces. Calculations are based on typical airplane characteristics with certain factors varied to cover a range of current designs. Stability charts are included to show the limiting values of the aerodynamic hinge moments and the weight hinge moments of the control surfaces for various positions of the center of gravity of the airplane and for control systems with various moments of inertia. The effects of reducing the chord and of eliminating the floating tendency of the surface, of changing the wing loading, and of decreasing the radius of gyration of the airplane are also indicated. An investigation has also been made of the nature of the motion of the airplane with controls free and of the modes of instability that may occur.

Jones, Robert T↗
NASA NTRS1951

A theoretical analysis of the effect of time lag in an automatic stabilization system on the lateral oscillatory stability of an airplane

A method is presented for determining the effect of time lag in an automatic stabilization system on the lateral oscillatory stability of an airplane. The method is based on an analytical-graphical procedure. The critical time lag of the airplane-autopilot system is readily determined from the frequency-response analysis. The method is applied to a typical present-day airplane equipped with an automatic pilot sensitive to yawing acceleration and geared to the rudder so that rudder control is applied in proportion to the yawing acceleration. The results calculated for this airplane-autopilot system by this method are compared with the airplane motions calculated by a step-by-step procedure.

Sternfield, Leonard↗
NASA NTRS1999

A Parametric Study of Accelerations of an Airplane Due to a Wake Vortex System

A study was conducted using strip theory to systematically investigate the effects of progressively more complete descriptions of the interaction of an airplane with a wake vortex system. The emphasis was in roll-dominant, parallel, vortex encounters. That is, the simulated airplane's longitudinal axis was nearly parallel to the rotation axis of the vortex system for most of the results presented. The study began with a drag-less rectangular wing in the flow field of a single vortex and progressed to a complete airplane with aerodynamic surfaces possessing taper, sweep, dihedral, and stalling and immersed in the flow field of a vortex pair in ground effect. The effects of the pitch, roll, and yaw attitudes of the airplane on the calculated accelerations were also investigated. The airplane had the nominal characteristics of a Boeing 757, and the vortex flow field had the nominal characteristics of the wake of a Boeing 767. The Bumham-Hallock model of a vortex flow field was used throughout the study. The data are presented mainly in terms of contours of equal acceleration in a two-dimensional area centered on the vortex pair and having dimensions of 300 feet by 300 feet.

Stewart, Eric C.↗
NASA NTRS1950

Gust-Tunnel Investigation to Determine the Load at the Joint of a Coupled Airplane Configuration Encountering a Gust

An investigation has been made in the Langley gust tunnel with two identical airplane models approximating 1/40-scale models of the B-29, coupled in tandem with a boom so that the individual centers of gravity were equidistant from the single coupling joint at the tail of the lead airplane. Time histories of the boom joint load were obtained as the models were flown through a gust. The results indicate that on a similar configuration involving airplanes the size of B-29 airplanes a load on the boom joint of 10,000 to 14,000 pounds could be induced by encountering a gust of 50 feet per second and having a gradient distance of 17 chords, at a forward speed of 380 feet per second and that the total load is extremely sensitive to the steadiness of flight that can be maintained with or without a gust. It is felt that the results are probably satisfactory to show order of magnitude, but it does not appear possible that a precise determination of the joint load that would be applicable to the full-scale airplanes can be obtained by gust-tunnel tests.

Cahen, George L.↗
NASA NTRS1956

Directional Stability of Towed Airplanes

So far, very careful investigations have been made regarding the flight properties, in particular the static and dynamic stability, of engine-propelled aircraft and of untowed gliders. In contrast, almost no investigations exist regarding the stability of airplanes towed by a towline. Thus, the following report will aim at investigating the directional stability of the towed airplane and, particularly, at determining what parameters of the flight attitude and what configuration properties affect the stability. The most important parameters of the flight attitude are the dynamic pressure, the aerodynamic coefficients of the flight attitude, and the climbing angle. Among the configuration properties, the following exert the greatest influence on the stability: the tow-cable length, the tow-cable attachment point, the ratio of the wing loadings of the towing and the towed airplanes, the moments of inertia, and the wing dihedral of the towed airplane. In addition, the size and shape of the towed airplane vertical tail, the vertical tail length, and the fuselage configuration are decisive factors in determining the yawing moment and side force due to sideslip, respectively.

Soehne, W.↗
NASA NTRS1957

Aerodynamic Characteristics of a 0.04956-Scale Model of the Convair TF-102A Airplane at Transonic Speeds, Coord. No. AF-120

The basic aerodynamic characteristics of a 0.04956-scale model of the Convair TF-102A airplane with controls undeflected have been determined at Mach numbers from 0.60 to 1.135 for angles of attack up to approximately 22 deg in the Langley 8-foot transonic tunnel. In addition, comparisons have been made with data obtained from a previous investigation of a 0.04956-scale model of the Convair F-102A airplane. The results indicated the TF-102A airplane was longitudinally stable for all conditions tested. An increase in lift-curve slope from 0.045 to 0.059 and an 11-percent rearward shift in aerodynamic-center location occurred with increases in Mach number from 0.60 to approximately 1.05. The zero-lift drag coefficient for the TF-102A airplane increased 145 percent between the Mach numbers of 0.85 and 1.075; the maximum lift-drag ratio decreased from 9.5 at a Mach number of 0.60 to 5.0 at Mach numbers above 1.025. There was little difference in the lift and pitching-moment characteristics and drag due to life between the TF-102A and F-102A configurations. However, as compared with the F-102A airplane, the zero-lift drag-rise Mach number for the TF-102A was reduced by at least 0.06, the zero-lift peak wave drag was increased 50 percent, and the maximum lift-drag ratio was reduced as much as 20 percent.

Osborne, Robert S.↗
NASA NTRS1956

Concluding Report on Free-Spinning and Recovery Characteristics of a 1/24-Scale Model of the Grumman F11F-1 Airplane, TED No. NACA AD 395

An investigation has been completed in the Langley 20-foot free-spinning tunnel on a l/24-scale model of the Grumman F11F-1 airplane to determine its spin and recovery characteristics. An interim report, Research Memorandum SL55G20, was published earlier and the present report concludes the presentation of results of the investigation. Primarily, the present report presents results obtained with engine gyroscopic moments simulated on the model. Also, the current results were obtained with a revised larger vertical tail recently incorporated on the airplane. It was difficult to obtain developed spins on the model when the spin direction was in the same sense as that of the engine rotation (right spin on the airplane). The developed spins obtained were very oscillatory and the recoveries were unsatisfactory. These results were similar to those previously reported for which engine rotation was not simulated. When the spin direction was in the opposite sense (left spin on the airplane), however, developed spins were readily obtainable. Recoveries from these spins also were unsatisfactory. Satisfactory recoveries were obtained on the model, however, when rudder reversal was accompanied by extension of small canards near the nose of the airplane or by deflection of the horizontal tail differentially with the spin.

Bowman, James S., Jr.↗
NASA NTRS1947

Free-Spinning-Tunnel Tests of a 1/27-Scale Model of the Douglas XF3D-1 Airplane, TED No. NACA DE 312

Free-spinning-tunnel tests have been made on a 1/27-scale model of the Douglas XF3D-1 airplane to confirm a preliminary evaluation made of the airplane spin and recovery characteristics and previously reported. Recovery characteristics were satisfactory for erect and inverted spins when the model was in the clean condition. When the slow-down brakes were open, recoveries were slow. The pedal force necessary to reverse the airplane rudder during a spin will be within the physical capabilities of the pilot. A 10-foot-diameter parachute attached to the tail of the airplane (laid-out-flat diameter, drag coefficient 0.7) or a 4.5-foot-diameter parachute attached to the outboard wing tip will be satisfactory for emergency spin recovery from demonstration spins. If it becomes necessary for the crew to abandon the airplane during a spin, they should leave from the outboard side of the cockpit. The test results indicated spin and recovery characteristics generally similar to those indicated in the preliminary evaluation.

Scher, Stanley H.↗