Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRPLANES - STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Lateral-directional aerodynamic characteristics of light, twin-engine, propeller driven airplanes

Analytical procedures and design data for predicting the lateral-directional static and dynamic stability and control characteristics of light, twin engine, propeller driven airplanes for propeller-off and power-on conditions are reported. Although the consideration of power effects is limited to twin engine airplanes, the propeller-off considerations are applicable to single engine airplanes as well. The procedures are applied to a twin engine, propeller driven, semi-low-wing airplane in the clean configuration through the linear lift range. The calculated derivative characteristics are compared with wind tunnel and flight data. Included in the calculated characteristics are the spiral mode, roll mode, and Dutch roll mode over the speed range of the airplane.

Wolowicz, C. H.↗
NASA NTRS1974

Flight evaluation of advanced control systems and displays on a general aviation airplane

A flight-test program was conducted to determine the effect of advanced flight control systems and displays on the handling qualities of a light twin-engined airplane. A flight-director display and an attitude-command control system, used separately and in combination, transformed a vehicle with poor handling qualities during ILS approaches in turbulent air into a vehicle with good handling qualities. The attitude-command control system also improved the ride qualities of the airplane. A rate-command control system made only small improvements to the airplane's ILS handling qualities in turbulence. Both the rate- and the attitude-command control systems reduced stall warning in the test airplane, increasing the likelihood of inadvertent stalls. The final approach to the point of flare was improved by both the rate- and the attitude-command control systems. However, the small control wheel deflections necessary to flare were unnatural and tended to cause overcontrolling during flare. Airplane handling qualities are summarized for each control-system and display configuration.

Loschke, P. C.↗
NASA NTRS1975

Computed lateral rate and acceleration power spectral response of conventional and STOL airplanes to atmospheric turbulence

Power-spectral-density calculations were made of the lateral responses to atmospheric turbulence for several conventional and short take-off and landing (STOL) airplanes. The turbulence was modeled as three orthogonal velocity components, which were uncorrelated, and each was represented with a one-dimensional power spectrum. Power spectral densities were computed for displacements, rates, and accelerations in roll, yaw, and sideslip. In addition, the power spectral density of the transverse acceleration was computed. Evaluation of ride quality based on a specific ride quality criterion was also made. The results show that the STOL airplanes generally had larger values for the rate and acceleration power spectra (and, consequently, larger corresponding root-mean-square values) than the conventional airplanes. The ride quality criterion gave poorer ratings to the STOL airplanes than to the conventional airplanes.

Lichtenstein, J. H.↗
NASA NTRS1976

The effect of lateral controls in producing motion of an airplane as computed from wind-tunnel data

An analytical study of the lateral controllability of an airplane has been made in which both the static rolling and yawing moments supplied by the controls and the reactions due to the inherent stability of the airplane have been taken into account. A hypothetical average airplane, embodying the essential characteristics of both the wind tunnel models and the full size test airplanes, was assumed for the study. Computations made of forced rolling and yawing motions of an F-22 airplane caused by a sudden deflection of the ailerons were found to agree well with actual measurements of these motions. The conditions following instantaneous full deflections of the lateral control have been studied, and some attention has been devoted to the controlling of complete turn maneuvers.

Weick, F. E.↗
NASA NTRS1976

An analysis of the stability of an airplane with free controls

The conditions essential to the stability of an airplane with free control surfaces are studied. Calculations are based on typical airplane characteristics with certain factors varied to cover a range of current designs. The effects of reducing the chord and of eliminating the floating tendency of the surface, of changing the wing loading and of decreasing the radius of gyration of the airplane are indicated. An investigation has also been made of the nature of the motion of the airplane with controls free and of the modes of instability that may occur. Stability with the controls free generally depends more critically on the design of the control system than on the stability characteristics of the airplane.

Jones, R. T.↗
NASA NTRS1977

Flight-measured lift and drag characteristics of a large, flexible, high supersonic cruise airplane

Flight measurements of lift, drag, and angle of attack were obtained for the XB-70 airplane, a large, flexible, high supersonic cruise airplane. This airplane had a length of over 57 meters, a takeoff gross mass of over 226,800 kilograms, and a design cruise speed of Mach 3 at an altitude of 21,340 meters. The performance measurements were made at Mach numbers from 0.72 to 3.07 and altitudes from approximately 7620 meters to 21,340 meters. The measurements were made to provide data for evaluating the techniques presently being used to design and predict the performance of aircraft in this category. Such performance characteristics as drag polars, lift-curve slopes, and maximum lift-to-drag ratios were derived from the flight data. The base drag of the airplane, changes in airplane drag with changes in engine power setting at transonic speeds, and the magnitude of the drag components of the propulsion system are also discussed.

Arnaiz, H. H.↗
NASA NTRS1978

A flight investigation of the stability, control, and handling qualities of an augmented jet flap STOL airplane

The stability, control, and handling qualities of an augmented jet flap STOL airplane are presented. The airplane is an extensively modified de Havilland Buffalo military transport. The modified airplane has two fan-jet engines which provide vectorable thrust and compressed air for the augmentor jet flap and Boundary-Layer Control (BLC). The augmentor and BLC air is cross ducted to minimize asymmetric moments produced when one engine is inoperative. The modifications incorporated in the airplane include a Stability Augmentation System (SAS), a powered elevator, and a powered lateral control system. The test gross weight of the airplane was between 165,000 and 209,000 N (37,000 and 47,000 lb). Stability, control, and handling qualities are presented for the airspeed range of 40 to 180 knots. The lateral-directional handling qualities are considered satisfactory for the normal operating range of 65 to 160 knots airspeed when the SAS is functioning. With the SAS inoperative, poor turn coordination and spiral instability are primary deficiencies contributing to marginal handling qualities in the landing approach. The powered elevator control system enhanced the controllability in pitch, particularly in the landing flare and stall recovery.

Vomaske, R. F.↗
NASA NTRS1978

Comparison of low-frequency noise levels of the Concorde supersonic transport with other commercial service airplanes

Fifty-two airplane noise recordings, made at several locations around Dulles International Airport, were analyzed to compare the low-frequency noise levels of the Concorde supersonic transport with those of other commercial jet airplanes. Comparisons of the relative low-frequency noise levels which were produced at close and distant locations for departures and arrivals were made for three noise measures: the sound pressure level in the 1/3 octave band centered at 20 Hz, the total sound pressure level in the 1/3 octave bands with center frequencies less than or equal to 125 Hz, and the total sound pressure level in the 1/3 octave bands with center frequencies less than or equal to 500 Hz. Although the absolute noise levels for Concorde were found, in general, to be higher than those for the other airplane types, the level of low-frequency noise of the Concorde relative to the perceived noise level (PNL), effective perceived noise level (EPNL), and overall sound pressure level (OASPL) was within the range established by the other airplane types, except for the arrival operations of four-engine, narrow-body airplanes. The measure OASPL was found to be a significantly better predictor of low-frequency noise level than PNL or EPNL.

Powell, C. A.↗
NASA NTRS1980

Precision controllability of the YF-17 airplane

A flying qualities evaluation conducted on the YF-17 airplane permitted assessment of its precision controllability in the transonic flight regime over the allowable angle of attack range. The precision controllability (tailchase tracking) study was conducted in constant-g and windup turn tracking maneuvers with the command augmentation system (CAS) on, automatic maneuver flaps, and the caged pipper gunsight depressed 70 mils. This study showed that the YF-17 airplane tracks essentially as well at 7 g's to 8 g's as earlier fighters did at 4 g's to 5 g's before they encountered wing rock. The pilots considered the YF-17 airplane one of the best tracking airplanes they had flown. Wing rock at the higher angles of attack degraded tracking precision, and lack of control harmony made precision controllability more difficult. The revised automatic maneuver flap schedule incorporated in the airplane at the time of the tests did not appear to be optimum. The largest tracking errors and greatest pilot workload occurred at high normal load factors at low angles of attack. The pilots reported that the high-g maneuvers caused some tunnel vision and that they found it difficult to think clearly after repeated maneuvers.

Sisk, T. R.↗
NASA NTRS1980

Exploratory piloted simulator study of the effects of winglets on handling qualities of a representative agricultural airplane

The effects on handling qualities of adding winglets to a representative agricultural aircraft configuration during swath-run maneuvering were evaluated. Aerodynamic data used in the simulation were based on low-speed wind tunnel tests of a full scale airplane and a subscale model. The Cooper-Harper handling qualities rating scale, supplementary pilot comments, and pilot vehicle performance data were used to describe the handling qualities of the airplane with the different wing-tip configurations. Results showed that the lateral-directional handling qualities of the airplane were greatly affected by the application of winglets and winglet cant angle. The airplane with winglets canted out 20 deg exhibited severely degraded lateral directional handling qualities in comparison to the basic airplane. When the winglets were canted inward 10 deg, the flying qualities of the configuration were markedly improved over those of the winglet-canted-out configuration or the basic configuration without winglets, indicating that proper tailoring of the winglet design may afford a potential benefit in the area of handling qualities.

Ogburn, M. E.↗
NASA NTRS1980

Impact of changing fuel characteristics on supersonic cruise airplane

The question of an advanced supersonic cruise research airplane is related to future oil supplies and prices. Technical data on the impact of changing fuel characteristics on the SCR airplane were developed. Projections of crude oil characteristics typical of the 1985 to 2000 time period were made with the help of consultants to the oil industry. Refineries for the future were modeled to establish jet fuel of engine and aircraft systems for future airplanes, with emphasis on supersonic cruise airplanes. Study results do not show a need for broadening the fuel specification. Hypothetical study fuels with broader specifications were defined, however, as was the impact of their properties on the SCR airplane and systems.

Hadaller, O. J.↗
NASA NTRS1953

Icing Protection for a Turbojet Transport Airplane: Heating Requirements, Methods of Protection, and Performance Penalties

The problems associated with providing icing protection for the critical components of a typical turbojet transport airplane operating over a range of probable icing conditions are analyzed and discussed. Heating requirements for several thermal methods of protection are evaluated and the airplane performance penalties associated with providing this protection from various energy sources are assessed. The continuous heating requirements for icing protection and the associated airplane performance penalties for the turbojet transport are considerably increased over those associated with lower-speed aircraft. Experimental results show that the heating requirements can be substantially reduced by the deve1opment of a satisfactory cyclic deicing system. The problem of providing protection can be minimized by employing a proper energy source since the airplane performance penalties vary considerably with the source of energy employed. The optimum icing protection system for the turbojet transport or for any other particular aircraft cannot be generally specified; the choice of the optimum system is dependent upon the specific characteristics of the airplane and engine, the flight plan, the probable icing conditions, and the performance requirements of the aircraft.

Gelder, Thomas F.↗
NASA NTRS1982

Summary of theoretical considerations and wind tunnel tests of an aerodynamic spoiler for stall proofing a general aviation airplane

An airplane stall proofing system utilizing a spoiler was investigated for application on a low wing airplane representative of typical general aviation aircraft. Tests of the full scale airplane were conducted in the NASA Langley 30 x 60 foot full scale wind tunnel. The test velocity was 86 feet per second, corresponding to a Reynolds number of 2.20 million. The stall proofing capability of the spoiler is shown and a theoretical approach to the design of the spoiler and analysis of the spoiler's contribution to the airplane's trim and longitudinal stability is verified. Controlled spoiler deployment in a narrow angle of attack range, 4 degrees, immediately preceding the stall angle will stall proof the airplane. The results also show some of the limitations of flight tests to determine spoiler deployment rate for good handling qualities.

Chevalier, H. L.↗
NASA NTRS1983

Determination of aerodynamic parameters of a fighter airplane from flight data at high angles of attack

A procedure for the estimation of airplane model structure and parameters is applied to data from a modern fighter airplane operating within an angle of attack range of 5 to 60 deg. The paper briefly describes the airplane, flight and wind tunnel data available, and the estimation method. The results presented contain basic longitudinal characteristics of the airplane and the estimates of aerodynamic parameters in the yawing-moment equations. These estimates are obtained from small and large amplitude maneuvers. Because the latter set of data was not suitable for airplane identification, some of the large amplitude maneuvers were joined together and then partitioned into subsets according to the values of angle of attack. Each subset was then analyzed as a separate data set. Most of the estimated parameters and functions are in good agreement with the wind tunnel measurements. The estimated lateral parameters in the model equations also demonstrate good prediction capabilities.

Klein, V.↗
NASA NTRS1983

Flight-test of the glide-slope track and flare-control laws for an automatic landing system for a powered-lift STOL airplane

An automatic landing system was developed for the Augmentor Wing Jet STOL Research Airplane to establish the feasibility and examine the operating characteristics of a powered-lift STOL transport flying a steep, microwave landing system (MLS) glide slope to automatically land on a STOL port. The flight test results address the longitudinal aspects of automatic powered lift STOL airplane operation including glide slope tracking on the backside of the power curve, flare, and touchdown. Three different autoland control laws were evaluated to demonstrate the tradeoff between control complexity and the resulting performance. The flight test and simulation methodology used in developing conventional jet transport systems was applied to the powered-lift STOL airplane. The results obtained suggest that an automatic landing system for a powered-lift STOL airplane operating into an MLS-equipped STOL port is feasible. However, the airplane must be provided with a means of rapidly regulation lift to satisfactorily provide the glide slope tracking and control of touchdown sink rate needed for automatic landings.

Watson, D. M.↗
NASA NTRS1984

Reconfigurable multivariable control law for commercial airplane using a direct digital output feedback design

The ability of a pilot to reconfigure the control surfaces on an airplane after a failure, allowing the airplane to recover to a safe condition for landing, becomes more difficult with increasing airplane complexity. Techniques are needed to stabilize and control the airplane immediately after a failure, allowing the pilot time to make longer range decisions. This paper shows a design of a discrete multivariable control law using four controls for the longitudinal channel of a B-737. Single control element failures are allowed in three of the four controls. The four controls design and failure cases are analyzed by means of a digital airplane simulation, with regard to tracking capability and ability to overcome severe windshear and turbulence during the aproach and landing phase of flight.

Ostroff, A. J.↗
NASA NTRS1986

Development of spin resistance criteria for light general aviation airplanes

A brief history of stall/spin technology for light general aviation airplanes is presented. Criteria needed to describe desirable characteristics of a spin-resistant airplane and means to evaluate airplanes for compliance with the criteria have been developed. Initial results from limited flight tests of an experimental high-wing airplane indicated that the basic configuration would not meet the spin resistance criteria. Further tests with the airplane modified to enhance its spin resistance are planned.

Dicarlo, D. J.↗
NASA NTRS1987

Spin resistance evaluation of a light airplane

A brief history of stall/spin technology for light general aviation airplanes and proposed criteria to describe desirable characteristics of a spin-resistant airplane are presented. Flight tests of a representative light airplane to evaluate compliance with and usefulness of the criteria are presented. The baseline airplane configuration would not meet the spin resistance criteria. Tests of the airplane with a wing leading edge modification to enhance its spin resistance showed compliance with the proposed criteria.

Stough, H. Paul, III↗