Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRPLANES - TRIM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

A flight investigation of the stability, control, and handling qualities of an augmented jet flap STOL airplane

The stability, control, and handling qualities of an augmented jet flap STOL airplane are presented. The airplane is an extensively modified de Havilland Buffalo military transport. The modified airplane has two fan-jet engines which provide vectorable thrust and compressed air for the augmentor jet flap and Boundary-Layer Control (BLC). The augmentor and BLC air is cross ducted to minimize asymmetric moments produced when one engine is inoperative. The modifications incorporated in the airplane include a Stability Augmentation System (SAS), a powered elevator, and a powered lateral control system. The test gross weight of the airplane was between 165,000 and 209,000 N (37,000 and 47,000 lb). Stability, control, and handling qualities are presented for the airspeed range of 40 to 180 knots. The lateral-directional handling qualities are considered satisfactory for the normal operating range of 65 to 160 knots airspeed when the SAS is functioning. With the SAS inoperative, poor turn coordination and spiral instability are primary deficiencies contributing to marginal handling qualities in the landing approach. The powered elevator control system enhanced the controllability in pitch, particularly in the landing flare and stall recovery.

Vomaske, R. F.↗
NASA NTRS1978

Comparison of low-frequency noise levels of the Concorde supersonic transport with other commercial service airplanes

Fifty-two airplane noise recordings, made at several locations around Dulles International Airport, were analyzed to compare the low-frequency noise levels of the Concorde supersonic transport with those of other commercial jet airplanes. Comparisons of the relative low-frequency noise levels which were produced at close and distant locations for departures and arrivals were made for three noise measures: the sound pressure level in the 1/3 octave band centered at 20 Hz, the total sound pressure level in the 1/3 octave bands with center frequencies less than or equal to 125 Hz, and the total sound pressure level in the 1/3 octave bands with center frequencies less than or equal to 500 Hz. Although the absolute noise levels for Concorde were found, in general, to be higher than those for the other airplane types, the level of low-frequency noise of the Concorde relative to the perceived noise level (PNL), effective perceived noise level (EPNL), and overall sound pressure level (OASPL) was within the range established by the other airplane types, except for the arrival operations of four-engine, narrow-body airplanes. The measure OASPL was found to be a significantly better predictor of low-frequency noise level than PNL or EPNL.

Powell, C. A.↗
NASA NTRS1980

Precision controllability of the YF-17 airplane

A flying qualities evaluation conducted on the YF-17 airplane permitted assessment of its precision controllability in the transonic flight regime over the allowable angle of attack range. The precision controllability (tailchase tracking) study was conducted in constant-g and windup turn tracking maneuvers with the command augmentation system (CAS) on, automatic maneuver flaps, and the caged pipper gunsight depressed 70 mils. This study showed that the YF-17 airplane tracks essentially as well at 7 g's to 8 g's as earlier fighters did at 4 g's to 5 g's before they encountered wing rock. The pilots considered the YF-17 airplane one of the best tracking airplanes they had flown. Wing rock at the higher angles of attack degraded tracking precision, and lack of control harmony made precision controllability more difficult. The revised automatic maneuver flap schedule incorporated in the airplane at the time of the tests did not appear to be optimum. The largest tracking errors and greatest pilot workload occurred at high normal load factors at low angles of attack. The pilots reported that the high-g maneuvers caused some tunnel vision and that they found it difficult to think clearly after repeated maneuvers.

Sisk, T. R.↗
NASA NTRS1980

Exploratory piloted simulator study of the effects of winglets on handling qualities of a representative agricultural airplane

The effects on handling qualities of adding winglets to a representative agricultural aircraft configuration during swath-run maneuvering were evaluated. Aerodynamic data used in the simulation were based on low-speed wind tunnel tests of a full scale airplane and a subscale model. The Cooper-Harper handling qualities rating scale, supplementary pilot comments, and pilot vehicle performance data were used to describe the handling qualities of the airplane with the different wing-tip configurations. Results showed that the lateral-directional handling qualities of the airplane were greatly affected by the application of winglets and winglet cant angle. The airplane with winglets canted out 20 deg exhibited severely degraded lateral directional handling qualities in comparison to the basic airplane. When the winglets were canted inward 10 deg, the flying qualities of the configuration were markedly improved over those of the winglet-canted-out configuration or the basic configuration without winglets, indicating that proper tailoring of the winglet design may afford a potential benefit in the area of handling qualities.

Ogburn, M. E.↗
NASA NTRS1980

Impact of changing fuel characteristics on supersonic cruise airplane

The question of an advanced supersonic cruise research airplane is related to future oil supplies and prices. Technical data on the impact of changing fuel characteristics on the SCR airplane were developed. Projections of crude oil characteristics typical of the 1985 to 2000 time period were made with the help of consultants to the oil industry. Refineries for the future were modeled to establish jet fuel of engine and aircraft systems for future airplanes, with emphasis on supersonic cruise airplanes. Study results do not show a need for broadening the fuel specification. Hypothetical study fuels with broader specifications were defined, however, as was the impact of their properties on the SCR airplane and systems.

Hadaller, O. J.↗
NASA NTRS1953

Icing Protection for a Turbojet Transport Airplane: Heating Requirements, Methods of Protection, and Performance Penalties

The problems associated with providing icing protection for the critical components of a typical turbojet transport airplane operating over a range of probable icing conditions are analyzed and discussed. Heating requirements for several thermal methods of protection are evaluated and the airplane performance penalties associated with providing this protection from various energy sources are assessed. The continuous heating requirements for icing protection and the associated airplane performance penalties for the turbojet transport are considerably increased over those associated with lower-speed aircraft. Experimental results show that the heating requirements can be substantially reduced by the deve1opment of a satisfactory cyclic deicing system. The problem of providing protection can be minimized by employing a proper energy source since the airplane performance penalties vary considerably with the source of energy employed. The optimum icing protection system for the turbojet transport or for any other particular aircraft cannot be generally specified; the choice of the optimum system is dependent upon the specific characteristics of the airplane and engine, the flight plan, the probable icing conditions, and the performance requirements of the aircraft.

Gelder, Thomas F.↗
NASA NTRS1983

Determination of aerodynamic parameters of a fighter airplane from flight data at high angles of attack

A procedure for the estimation of airplane model structure and parameters is applied to data from a modern fighter airplane operating within an angle of attack range of 5 to 60 deg. The paper briefly describes the airplane, flight and wind tunnel data available, and the estimation method. The results presented contain basic longitudinal characteristics of the airplane and the estimates of aerodynamic parameters in the yawing-moment equations. These estimates are obtained from small and large amplitude maneuvers. Because the latter set of data was not suitable for airplane identification, some of the large amplitude maneuvers were joined together and then partitioned into subsets according to the values of angle of attack. Each subset was then analyzed as a separate data set. Most of the estimated parameters and functions are in good agreement with the wind tunnel measurements. The estimated lateral parameters in the model equations also demonstrate good prediction capabilities.

Klein, V.↗
NASA NTRS1983

Flight-test of the glide-slope track and flare-control laws for an automatic landing system for a powered-lift STOL airplane

An automatic landing system was developed for the Augmentor Wing Jet STOL Research Airplane to establish the feasibility and examine the operating characteristics of a powered-lift STOL transport flying a steep, microwave landing system (MLS) glide slope to automatically land on a STOL port. The flight test results address the longitudinal aspects of automatic powered lift STOL airplane operation including glide slope tracking on the backside of the power curve, flare, and touchdown. Three different autoland control laws were evaluated to demonstrate the tradeoff between control complexity and the resulting performance. The flight test and simulation methodology used in developing conventional jet transport systems was applied to the powered-lift STOL airplane. The results obtained suggest that an automatic landing system for a powered-lift STOL airplane operating into an MLS-equipped STOL port is feasible. However, the airplane must be provided with a means of rapidly regulation lift to satisfactorily provide the glide slope tracking and control of touchdown sink rate needed for automatic landings.

Watson, D. M.↗
NASA NTRS1984

Reconfigurable multivariable control law for commercial airplane using a direct digital output feedback design

The ability of a pilot to reconfigure the control surfaces on an airplane after a failure, allowing the airplane to recover to a safe condition for landing, becomes more difficult with increasing airplane complexity. Techniques are needed to stabilize and control the airplane immediately after a failure, allowing the pilot time to make longer range decisions. This paper shows a design of a discrete multivariable control law using four controls for the longitudinal channel of a B-737. Single control element failures are allowed in three of the four controls. The four controls design and failure cases are analyzed by means of a digital airplane simulation, with regard to tracking capability and ability to overcome severe windshear and turbulence during the aproach and landing phase of flight.

Ostroff, A. J.↗
NASA NTRS1986

Development of spin resistance criteria for light general aviation airplanes

A brief history of stall/spin technology for light general aviation airplanes is presented. Criteria needed to describe desirable characteristics of a spin-resistant airplane and means to evaluate airplanes for compliance with the criteria have been developed. Initial results from limited flight tests of an experimental high-wing airplane indicated that the basic configuration would not meet the spin resistance criteria. Further tests with the airplane modified to enhance its spin resistance are planned.

Dicarlo, D. J.↗
NASA NTRS1987

Spin resistance evaluation of a light airplane

A brief history of stall/spin technology for light general aviation airplanes and proposed criteria to describe desirable characteristics of a spin-resistant airplane are presented. Flight tests of a representative light airplane to evaluate compliance with and usefulness of the criteria are presented. The baseline airplane configuration would not meet the spin resistance criteria. Tests of the airplane with a wing leading edge modification to enhance its spin resistance showed compliance with the proposed criteria.

Stough, H. Paul, III↗
NASA NTRS1988

It's time to reinvent the general aviation airplane

Current designs for general aviation airplanes have become obsolete, and avenues for major redesign must be considered. New designs should incorporate recent advances in electronics, aerodynamics, structures, materials, and propulsion. Future airplanes should be optimized to operate satisfactorily in a positive air traffic control environment, to afford safety and comfort for point-to-point transportation, and to take advantage of automated manufacturing techniques and high production rates. These requirements have broad implications for airplane design and flying qualities, leading to a concept for the Modern Equipment General Aviation (MEGA) airplane. Synergistic improvements in design, production, and operation can provide a much needed fresh start for the general aviation industry and the traveling public. In this investigation a small four place airplane is taken as the reference, although the proposed philosophy applies across the entire spectrum of general aviation.

Stengel, Robert F.↗
NASA NTRS1987

Class 2 design update for the family of commuter airplanes

This is the final report of seven on the design of a family of commuter airplanes. This design effort was performed in fulfillment of NASA/USRA grant NGT-8001. Its contents are as follows: (1) the class 1 baseline designs for the commuter airplane family; (2) a study of takeoff weight penalties imposed on the commuter family due to implementing commonality objectives; (3) component structural designs common to the commuter family; (4) details of the acquisition and operating economics of the commuter family, i.e., savings due to production commonality and handling qualities commonality are determined; (5) discussion of the selection of an advanced turboprop propulsion system for the family of commuter airplanes, and (6) a proposed design for an SSSA controller design to achieve similar handling for all airplanes. Final class 2 commuter airplane designs are also presented.

Creighton, Thomas R.↗
NASA NTRS1988

Use of Dynamically Scaled Models for Studies of the High-Angle-of-Attack Behavior of Airplanes

Dynamically scaled, free-flying models are used by the National Aeronautics and Space Administration (NASA) to study the stalling and spinning characteristics of civil and military airplane configurations. Such tests have been conducted for many different designs, and it has been possible to correlate the results predicted by the model tests with flight test results obtained in the investigations. The present paper describes four of the dynamic model testing techniques used at the NASA Langley Research Center, including the scaling laws used in the construction of models and in the interpretation of results. Predictions of stall/spin behavior based on model results have generally been very accurate, and the model tests are regarded as an invaluable precursor to full-scale flight tests. However, aerodynamic scale effects between some models and full-scale airplanes due to differences in test values of Reynolds number have resulted in erroneous predictions for a few configurations. A discussion of these effects is provided, together with the approach used to modify the model so that its behavior more closely matches that of the airplane. Finally, two typical applications of the techniques to the X-29A research airplane and several general aviation research airplanes are presented to illustrate the type of information provided by the tests.

Joseph R Chambers↗
NASA NTRS1988

An evaluation of automatic control system concepts for general aviation airplanes

A piloted simulation study of automatic longitudinal control systems for general aviation airplanes has been conducted. These automatic control systems were designed to make the simulated airplane easy to fly for a beginning or infrequent pilot. Different control systems are presented and their characteristics are documented. In a conventional airplane control system each cockpit controller commands combinations of both the airspeed and the vertical speed. The best system in the present study decoupled the airspeed and vertical speed responses to cockpit throttle inputs. That is, the cockpit throttle lever commanded only airspeed responses, and the longitudinal wheel position commanded only vertical speed responses. This system significantly reduced the pilot workload throughout an entire mission of the airplane from takeoff to landing. An important feature of the automatic system was that neither changing flap position nor maneuvering in steeply banked turns affected either the airspeed or the vertical speed. All the pilots who flew the control system simulation were favorably impressed with the very low workload and the excellent handling qualities of the simulated airplane.

Stewart, E. C.↗
NASA NTRS1988

Use of dynamically scaled models for studies of the high-angle-of-attack behavior of airplanes

Dynamically scaled, free-flying models are used by the National Aeronautics and Space Administration (NASA) to study the stalling and spinning characteristics of civil and military airplane configurations. Such tests have been conducted for many different designs, and it has been possible to correlate the results predicted by the model tests with flight test results obtained in the investigations. The present paper describes four of the dynamic model testing techniques used at the NASA Langley Research Center, including the scaling laws used in the construction of models and in the interpretation of results. Predictions of stall/spin behavior based on model results have generally been very accurate, and the model tests are regarded as an invaluable precursor to full-scale flight tests. However, aerodynamic scale effects between some models and full-scale airplanes due to differences in test values of Reynolds number have resulted in erroneous predictions for a few configurations. A discussion of these effects is provided, together with the approach used to modify the model so that its behavior more closely matches that of the airplane. Finally, two typical applications of the techniques to the X-29A research airplane and several general aviation research airplanes are presented to illustrate the type of information provided by the tests.

Joseph R Chambers↗
NASA NTRS1989

Airplane takeoff and landing performance monitoring system

The invention is a real-time takeoff and landing performance monitoring system which provides the pilot with graphic and metric information to assist in decisions related to achieving rotation speed (V sub R) within the safe zone of the runway or stopping the aircraft on the runway after landing or take off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. An important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in headwind occurring as the takeoff roll progresses. The system displays the position of the airplane on the runway, indicating runway used and runway available, summarizes the critical information into a situation advisory flag, flags engine failures and off-nominal acceleration performance, and indicates where on the runway particular events such as decision speed (V sub 1), rotation speed (V sub R) and expected stop points will occur based on actual or predicted performance. The display also indicates airspeed, wind vector, engine pressure ratios, second segment climb speed, and balanced field length (BFL). The system detects performance deficiencies by comparing the airplane's present performance with a predicted nominal performance based upon the given conditions.

Middleton, David B.↗
NASA NTRS1990

Microwave beam powered Mars airplane

The feasibility of an unmanned Mars airplane that receives its primary power from an RF (microwave) beam located on the Martian surface has been analyzed. An onboard rechargeable electrochemical storage system is to be used for special maneuvers, and possible range extension when the airplane is out of the line-of-sight of the microwave source antenna is included as a back-up to the microwave system. The weight of the onboard microwave beam receiving system, relative to other power systems, and the ability to recharge the onboard energy storage system in flight result in a payload capability independent of range and significant mission flexibility. Such an airplane, its onboard power system, its methods of utilization, and the transmitting station requirements to support various Martian exploration operations are presented. The status of microwave beam technology is given, in addition to the technology advances required for the microwave-beam-powered Mars airplane. The concept is thought to be feasible, but advances in microwave technology are required. It is concluded that the payload capability gives the Mars airplane significant operational flexibility and utilization.

Faymon, Karl A.↗