SEARCH · Search NASA

Results for “ALUMINATES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Experimental evidence for the acceleration of slag hydration in blended cements by the addition of CaCl2

Cements with high substitution rates of ground granulated blast furnace slags (GGBS) have the potential to significantly lower CO{sub 2} emissions of concrete, but their early age strength is often below those of traditional OPC cements. One way of mitigating this drawback is to use accelerating admixtures. In this study, the effect of CaCl{sub 2} additions on the hydration of blended cements was investigated by measuring compressive strength, porosity, heat release and propagation of ultrasound in blends containing 70 wt% of GGBS. The onset of formation of aluminate phases was monitored using in-situ XRD. The effect of CaCl{sub 2} on slag hydration was isolated by replacing GGBS by an inert quartz filler. Results showed that compressive strength values at one, two and seven days were increased by 50% by the CaCl{sub 2} addition. The increases in compressive strength corresponded to a reduction in pore space. GGBS hydration contributed to the heat development, structuration and compressive strength of the blended cements from 15 h. The addition of CaCl{sub 2} led to an earlier onset of the GGBS reaction, at around 10 h, and increased the rate of GGBS hydration during the first seven days. The time of onset of the GGBS contribution was also the moment when AFm precipitation started. In CaCl{sub 2}-containing blends, Cl was incorporated in AFm.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Continuous optical in-situ pH monitoring during early hydration of cementitious materials

A luminescent sensor technique for pH analyses has been tested in cementitious media. The optical sensors monitor in-situ pH every 5 s during early hydration reactions over a period of 100 h from initial fluid up to consolidated stage. The pH development was analysed in calcium aluminate, calcium sulfoaluminate and OPC/slag cements up to a pH level of 13.3 and directly correlated with the heat of hydration. Thus tracing the dissolution and formation processes of solid phases via pH sensor monitoring is possible. This measurement technique enables the recording of continuous and highly reproducible pH data sets from slurries, pastes, and hardening materials leading to new vistas for individual (trans)formation pathways of solids, hydration and consolidation reactions in high alkaline cementitious systems.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Molecular dynamics simulations of radiation response of $\mathrm{LiAlO_2}$ and $\mathrm{LiAl_5O_8}$

Here, we report the findings of a computational investigation of defect production and migration in two lithium aluminate ceramics: LiAlO 2 and LiAl 5 O 8 . Although the first ceramic, LiAlO 2 has been widely investigated computationally, especially via molecular dynamics (MD), there have been no MD studies done on LiAl 5 O 8 up to date, due to the lack of interatomic potentials for this system. This work implemented an existing set of Li-Al-O coulombic and Buckingham potential parameters for the LiAl 5 O 8 system from the literature, followed by validating it based on experimental values of density, crystallinity, bond lengths and melting point. The Li + diffusion in the two ceramics was examined and was found to be one order of magnitude slower in LiAl 5 O 8 (D 0 = 3.17 x 10 -11 m 2 /s) as compared to that in LiAlO 2 (D 0 = 4.02 x 10 -10 m 2 /s) at 600 K. The lithium vacancy migration barrier of 4.15 eV in LiAl 5 O 8 was more than three times that in LiAlO 2 (1.31 eV) possibly due to stronger ordering in the Li-O 6 octahedra of LiAl 5 O 8 than in Li-O 4 tetrahedra of LiAlO 2 . The Li displacement threshold energy (E d ) in LiAl 5 O 8 was found to have a median value of 68 eV which is much higher than that in LiAlO 2 (40 eV). The greater E d for Li signifies a lower likelihood for defect formation and clustering and thus lower tendency for amorphization in LiAl 5 O 8 . The presented results show the difference in defect dynamics in the two ceramics that may help us understand the susceptibility of the two ceramics to amorphization caused by irradiation.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Phase formation in the CaO–Al 2 O 3 –ZnO system as an analogue to CaO–Al 2 O 3 –MgO in spinel containing refractories

Recently, gahnite (ZnAl 2 O 4 ) is gaining attraction as a potential refractory ceramic because of the similarity of its structure and properties with those of magnesium aluminate (MgAl 2 O 4 ) spinel refractories. Formation of MgO and hibonite solid solution (CaMg x Al 12−x O 19−0.5x ; 0 ≤ x ≤ 0.18), CAM-I (Ca 2 Mg 2−3x Al 28+2x O 46 (0 ≤ x ≤ 0.3), and CAM-II (CaMg 2−3x Al 16+2x O 27 , 0 ≤ x ≤ 0.2) phases with platelet and interlocking microstructure in the CaO–Al 2 O 3 –MgO ternary system significantly enhances the high temperature mechanical properties of refractory castables. The CaO–Al 2 O 3 –ZnO ternary system has been studied, for the first time to our knowledge, in a selected compositional range with reference to the CaO–Al 2 O 3 –MgO system from 1650°C to 1700°C. The formation of ZnO and hibonite solid solution (CaZn x Al 12−x O 19−0.5x ; 0 < x < 0.18), CAZ-I (Ca 2 Zn 2−3x Al 28+2x O 46 ; 0 ≤ x ≤ 0.3), and CAZ-II (CaZn 2−3x Al 16+2x O 27 ; 0 ≤ x ≤ 0.2) phases with platelet and interlocking morphology have been found. The crystal structures and lattice parameters of ZnO and hibonite solid solution, CAZ-I, and CAZ-II are comparable, respectively, with MgO and hibonite solid solution, CAM-I, and CAM-II. Furthermore, CAZ-I and CAZ-II phases also form due to reaction between hibonite (CaO·6Al 2 O 3 ) and ZnAl 2 O 4 .

calcium aluminate cement↗

DOE OSTI2024

Assessment of Cementitious Composites for High-Temperature Geothermal Wells

High-temperature (HT) geothermal wells can provide green power 24 hours a day, 7 days a week. Under harsh environmental and operational conditions, the long-term durability requirements of such wells require special cementitious composites for well construction. This paper reports a comprehensive assessment of geothermal cement composites in cyclic pressure function laboratory tests and field exposures in an HT geothermal well (300–350 °C), as well as a numerical model to complement the experimental results. Performances of calcium–aluminate cement (CAC)-based composites and calcium-free cement were compared against the reference ordinary Portland cement (OPC)/silica blend. The stability and degradation of the tested materials were characterized by crystalline composition, thermo-gravimetric and elemental analyses, morphological studies, water-fillable porosity, and mechanical property measurements. All CAC-based formulations outperformed the reference blend both in the function and exposure tests. The reference OPC/silica lost its mechanical properties during the 9-month well exposure through extensive HT carbonation, while the properties of the CAC-based blends improved over that period. The Modified Cam-Clay (MCC) plasticity parameters of several HT cement formulations were extracted from triaxial and Brazilian tests and verified against the experimental results of function cyclic tests. These parameters can be used in well integrity models to predict the field-scale behavior of the cement sheath under geothermal well conditions.

15 GEOTHERMAL ENERGY↗

DOE OSTI2020

Advancement of Commercial Intumescent Expanding Foams for Deactivation and Decommissioning in the Nuclear Sector - 20198

Florida International University (FIU), in collaboration with The Department of Energy's Office of Environmental Management (DOE-EM), Savannah River National Laboratory (SRNL), and sites across the Savannah River complex, have identified an operational requirement for a fixative technology that is intended to immobilize and/or isolate residual contamination within a 3-dimensional space. Fixation of radiological contamination can reduce worker risk and mitigate potentially hazardous conditions, however nearly every marketed contamination fixative has been found to be flammable; a significant concern in radiological facilities. Coupled with this, industry fixatives are normally used as a thin coating which can present problems when attempting to stabilize irregular geometry or areas that are difficult to access whilst ensuring full coverage. The technical evaluation and advancement of commercial-off-the-shelf (COTS) polyurethane foams has yielded a down-selected candidate that shows potential in meeting the requirements to support deactivation and decommissioning activities. Several performance criteria have been established and tested to progress the technology readiness level towards an active field demonstration (TRL-7). Such criteria include: mechanical failure limits, adhesive and cohesive properties, thermal/fire resilience, determining thermal behavior, ability to immobilize contamination, and a means of non-destructive evaluation of applications. The test scenario examined was targeted towards an application for decommissioning nuclear pipework, in which the down-selected polyurethane foam would act as a barrier to segregate pipework and mitigate the potential for release during cutting, packaging, and storage operations. Testing carried out at SRNL included: mechanical evaluation of tensile, compressive, and adhesion strength by dynamic mechanical analysis (DMA), as well as thermogravimetric analysis (TGA). FIU examined the foam's fixative properties by utilizing phosphorescent europium-dysprosium doped strontium aluminate powder to investigating the extent to which contamination can be immobilized. FIU has also exploited previous successes in the field of intumescent technologies to assess the down-selected foam's tolerance to an extreme fire scenario, while maintaining the ability to effectively mitigate a contamination release. Parallel to this, extensive thermal investigations were carried out to determine the upper boundary of anticipated heat generation during the curing process as heat generation has the potential to compromise rubber parts of contaminated enclosures. These investigations subsequently yielded a promising method for a non-destructive application evaluation by means of infrared thermography. Utilizing the high sensitivity of modern IR cameras, coupled with the heat generated during the curing process of the polyurethane foam, FIU has been exploring the concept of monitoring the external pipe surface for indications of an irregular or abnormal application, thus informing operational decision making. The testing carried out utilized several current 'best fit' ASTM standards, which serve as helpful guidelines for testing, however, a precise definition of the operational parameters and requirements is still necessary. With continued collaboration with SRNL, FIU aims refine said definitions and develop new standards by which this, and other decommissioning technologies, can be accredited by relevant standards based testing. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2026

Hybrid Additive Manufacturing and Electric Field-Assisted Sintering of High-temperature Heat Exchangers via Sacrificial Channel Molds

A hybrid manufacturing approach, integrating additive manufacturing (AM) with powder methodology via electric field-assisted sintering (EFAS), was developed for the fabrication of high-temperature compact heat exchangers (CHX) from refractory metals. The methodology employed additively manufactured sacrificial channel molds (SCMs) as shapeholders for CHX channels, which were embedded in metal powders using EFAS. Following embedding, the SCMs were chemically dissolved to form the internal channel network. SCMs were fabricated using both digital light processing (DLP) and direct ink writing (DIW) from chemically reactive, calcium-based ceramic feedstocks with varying ratios of Al2O3 reinforcement. The microstructure, phase composition, and dissolution behavior of both as-printed and embedded SCMs were investigated. The shrinkage behavior of the SCMs embedded in refractory metals, as well as the interfacial characteristics between the SCMs and metal matrix, were studied. The results showed that the SCMs containing sufficient chemical reactive ceramics dissolved effectively before and after embedding. The as-printed SCMs retained the phase composition of their feedstocks, but the embedded SCMs containing calcium-based ceramics and Al2O3 exhibited the formation of calcium aluminates due to high temperature exposure during embedding. Most SCMs exhibited a cellular Al2O3 network filled with Ca-rich ceramics. Shrinkage after embedding was strongly dependent on SCM density, with lower density SCMs exhibiting greater shrinkage. A thin SCM-affected zone was observed at the metal matrix surface, characterized by increased porosity compared to the bulk matrix. This effect was attributed to infiltration of the SCM materials into powder particle boundaries under pressure, followed by their removal during dissolution. This study demonstrates the feasibility of manufacturing CHXs from hard-to-process refractory metals for use in harsh environments.

36 - MATERIALS SCIENCE↗

DOE OSTI2023

Combustion of 10–100 μm aluminum droplets in detonation products gases

Here we describe a two-phase model of combustion effects in aluminized high explosive (HE) charges. It is based on: (i) a Gas Dynamic Model of the expansion of the detonation product gases and their turbulent combustion with air; and (ii) a Heterogeneous Continuum Model of aluminum (Al) droplets and their combustion with the detonation product gases. Initial conditions are based on an analytical similarity solution for a cylindrical Chapman-Jouguet (CJ) detonation propagating at the CJ detonation velocity. The CJ jump conditions are computed at the thermodynamic equilibrium state by the Cheetah code, assuming the Al droplets are inert. We assume that the Al is 10 % of the charge mass and occurs as droplets at the CJ state. Different initial droplet diameters, ranging from 10 to 100 microns, are studied. A hydrodynamic combustion model based on large Damköhler numbers is employed in this study, -3σ(1 + 0.276 $\sqrt{Re}$)/($Kd^2_w$). It has a square-root dependence on the Reynolds number (Re) and inversed-squared dependence on the droplet diameter (d w ). The burnout time (t B ) of the Al droplets has a three-halves dependence on the droplet diameter, t B ~ ($d^0_w$) 3/2 . After burnout, the detonation products act as detonation products of the HE charge with active Al. They turbulently mix with air and form a combustion layer on the outer edge of the fireball. Details of the two-phase model, initial conditions and evolution of the flow field will be described.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Large Area Transfer of Bismuth‐Based Layered Oxide Thin Films Using a Flexible Polymer Transfer Method

Magnetic and ferroelectric oxide thin films have long been studied for their applications in electronics, optics, and sensors. The properties of these oxide thin films are highly dependent on the film growth quality and conditions. To maximize the film quality, epitaxial oxide thin films are frequently grown on single-crystal oxide substrates such as strontium titanate (SrTiO 3 ) and lanthanum aluminate (LaAlO 3 ) to satisfy lattice matching and minimize defect formation. However, these single-crystal oxide substrates cannot readily be used in practical applications due to their high cost, limited availability, and small wafer sizes. One leading solution to this challenge is film transfer. In this demonstration, a material from a new class of multiferroic oxides is selected, namely bismuth-based layered oxides, for the transfer. A water-soluble sacrificial layer of Sr 3 Al 2 O 6 is inserted between the oxide substrate and the film, enabling the release of the film from the original substrate onto a polymer support layer. The films are transferred onto new substrates of silicon and lithium niobate (LiNbO 3 ) and the polymer layer is removed. These substrates allow for the future design of electronic and optical devices as well as sensors using this new group of multiferroic layered oxide films.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Estimating the Contribution of the Nickel to Protium Loading of Full-Length Getters

The full-length getter (FLG) is a critical component of the tritium producing burnable absorber rod (TPBAR), designed to capture tritium produced within the lithium aluminate pellets. However, due to the chemical similarity between protium (¹H) and tritium (³H), the FLG readily absorbs protium, reducing its capacity to absorb tritium and increasing the risk of tritium permeation into the reactor coolant. This study evaluates protium produced from neutron irradiation of nickel plating on the FLG through 5?Ni(n,p) reactions, quantifies its contribution to the total protium observed, and informs models of tritium and hydrogen transport within TPBARs. During irradiation, neutron capture by 58Ni results in the formation of 5?Ni, which undergoes neutron bombardment to produce 4He via 5?Ni(n,a) reactions and protium via 5?Ni(n,p) reactions. The measured helium content post-irradiation provides insight into the neutron capture processes within the getter. The 4He measured within the getter may be useful in determining hydrogen produced by the nickel plating on FLG because 59Ni also produces protium in a 59Ni(n, p) reaction. The contribution of 1H from the nickel in FLG contributed less than 1% of the measured H2 gas in PIE, ranging from 0.005% to 0.614%. These findings refine current knowledge of the protium-tritium interplay in TPBARs and support the development of improved transport models for tritium and hydrogen, ultimately aiding in the optimization of TPBAR design and reactor operations.

Arbova, Dana L.↗

DOE OSTI2026

Migration of Al within dealuminated beta extruded catalysts influences olefin distribution during ethanol upgrading

Zeolites serve as essential catalytic platforms for many industrial processes, including emerging ethanol-to-olefins (ETO) upgrading technologies. Although metal-loaded (Cu, Zn, Y) dealuminated beta (deAlBeta) zeolite powders are promising catalysts for direct ETO conversion with high selectivity to butene-rich C3+ olefins necessary for production of sustainable aviation fuels (SAF), development of these materials as shaped technical bodies through the incorporation of binders is required for scale-up and commercial viability. Here, we report the ethanol upgrading performance of Cu-Zn-Y/deAlBeta extruded catalysts formulated with either alumina or kaolin clay binders. Both extrudates exhibit high ethanol dehydration reactivity which competes with the initial ethanol dehydrogenation step in the direct ETO reaction network. Consequently, elevated selectivity to dehydration side products (ethylene, diethyl ether) at ∼100% ethanol conversion is observed on Cu-Zn-Y/deAlBeta extrudates compared to the powder catalyst, which inhibits production of desired C3+ olefins. Utilizing microscopy and spectroscopic characterizations, we attribute this to Al migration from binder to zeolite particles within the extrudates, thus re-aluminating the zeolite and generating Brønsted acid sites active for dehydration reactions. This work elucidates the effects of binder incorporation on ETO product distributions and emphasizes that binder selection must be carefully considered during design of extruded zeolite catalysts.

Jacobs, Hunter [ORNL] (ORCID:000000016190874X)↗

DOE OSTI2020

Remarkable self-degradation of Cu/SAPO-34 selective catalytic reduction catalysts during storage at ambient conditions

A model Cu/SAPO-34 SCR catalyst with all Cu species maintained as isolated Cu(II) ions is synthesized herein. Following lengthy storage on the shelf under ambient conditions, this catalyst completely and irreversibly deactivates upon any heat treatments above ~100 °C. Via detailed characterizations with surface area/pore volume analysis, XRD, H 2 -TPR, and 27 Al, 29 Si and 31 P solid-state NMR, as well as continuous wave and pulsed EPR studies, it is concluded that over the course of storage, the SCR active sites [Cu(OH)] + and Brønsted acid sites ≡Si-O(H)-Al≡ are attacked by H 2 O molecules trapped in the SAPO-34 framework pores, and undergo hydrolysis to form copper hydroxide and terminal Al sites. Upon thermal treatment, these species interact with each other to form copper-aluminate-like species, leading to irreversible deactivation of this catalyst. This deactivation mechanism does not require or necessarily lead to extensive degradation (i.e., crystallinity loss) of the SAPO-34 support.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Evolution of elastic and thermal properties of cementitious composites containing micro-size lightweight fillers after exposure to elevated temperature

This work studies the evolution of elastic and thermal properties of cementitious composites containing micro-size lightweight fillers after exposure to elevated temperatures (up to 800 °C). A multiscale investigation is carried out to study the thermal degradation of cementitious composite materials at multiple scale levels: at cement past level, the dehydration kinetics of cement hydrates (i.e., C–S–H, CH and aluminate hydrates) and development of microcracks are studied as functions of exposure temperatures. The damage mechanism of the inclusion phases and damages within the interfacial transition zone (ITZ) under elevated temperature are also investigated. In addition, the change of mechanical (i.e., elastic moduli, compressive strengths) and thermal (thermal conductivities) properties are measured as functions of the exposure temperature. Based on the experimental studies, a multiscale thermal degradation model is developed where the thermal degradations of cement paste (including water composition, porosity, and solid phase changes), inclusion phases, and the interfaces are captured through a multiscale sub-stepping homogenization scheme. The thermal degradation model is validated through multiple sets of experimental data. Finally, the influence of key parameters including the particle size distribution of the inclusions, the chemical composition, as well as the effects of ITZ damage are studied.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Degradation mechanism of blended cement pastes in sulfate-bearing environments under applied electric fields: Sulfate attack vs. decalcification

Applied electric fields, the reason behind stray currents, accelerate the ingress of sulfate into cementitious materials. To identify mitigation approaches, this study investigates the effects of slag and fly ash on sodium sulfate attacks of cement pastes under a constant electric current. The mineralogical alterations induced by the attacks were analyzed using X-ray diffractometry, thermogravimetric analysis, scanning electron microscopy, and thermodynamic modeling. The dissolution of aluminates in the slag and fly ash induced a monosulfate-rich area (>~20 mm from the cathode surface) to form next to the ettringite-rich area on the sample surface (<~20 mm). This effect reduced the availability of SO 4 2– in the pore solution, thereby hindering the penetration of sulfate. Meanwhile, the consumption of portlandite by the pozzolanic reaction lowered the decalcification resistance of the materials. This produced a wide area that endured the decomposition of portlandite and carbonate-AFm. Altogether, blending 30% fly ash did not improve the resistance of the material to either sulfate attacks or decalcification; blending 50% slag can effectively mitigate sulfate ingress, though decalcification may become a governing mechanism in the degradation process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Sulfuric Acid Improves the Reactivity of Zeolites via Dealumination

The demand for supplementary cementitious materials (SCMs), like fly ash, slag, and silica fume, is projected to rise over the next few decades. However, global decarbonization efforts, such as decommissioning of coal-fired power plants, will limit the supply of SCMs. Therefore, alternative SCM sources are a critical need for the cement and concrete industry. However, the high crystallinity of zeolites limits their pozzolanic reactivity. The goal of this work was to improve the reactivity of two common zeolites, namely clinoptilolite and SSZ-13, by treating them with sulfuric acid. The treatment enhanced zeolite reactivity via dealumination and decreased particle sizes, which led to increased reactivity with calcium hydroxide, as indicated by a 42.0% increase in reaction heat measured by isothermal calorimetry. Here, we elucidate mechanistic understanding that smaller particle sizes induced by acid treatment accelerated peak heat evolution, while free aluminates from dealumination increased heat via direct reaction with aqueous Ca 2+ .

36 MATERIALS SCIENCE↗

DOE OSTI2025

Zavitsas’ hydration model for electrolytes only stable in the presence of another: NaAl(OH) 4 in aqueous NaOH solution

Many aqueous electrolytes are only stable in the presence of another electrolyte, such as electrolytes that are only soluble in strong acid or base. An example is sodium aluminate [NaAl(OH) 4 ], which is only stable in aqueous NaOH. This complicates developing thermodynamic parameters because it is difficult to separate the contributions of individual electrolytes in multicomponent solutions to measured bulk thermodynamic properties. The present study develops a method to determine the liquid phase parameters from solubility data for Zavitsas’ Hydration model, a model that incorporates hydration parameters into the activities of dissolved species. Furthermore, this study uses gibbsite [Al(OH) 3 ] solubility data in aqueous NaOH solution to develop Zavitsas' model parameters for NaAl(OH) 4 simultaneously with the equilibrium constants. A good fit of the solubility data was found, showing that Zavitsas’ model is effective for this system.

Bayer process↗

DOE OSTI2023

Mechanisms of dissolution from gibbsite step edges elucidated by ab initio molecular dynamics with enhanced sampling

Surface reactions underpin our collective understanding of mineral dissolution. This impacts a range of predictive geochemical models (for weathering, the fate and transport of metals) as well as industrial utilization of minerals. Yet atomistic details are rarely known due to the complex mineral/fluid interfacial environment. There is significant need to understand the mechanistic details of dissolution reactions and how they depend on surface morphology and solution conditions. This work utilizes surface pit models in conjunction with changes to solution composition that mimic pH to explore surface detachment of aluminate from gibbsite, which is a primary source of Al in soils and within the industrial processing of aluminum. Ab initio molecular dynamics simulations with enhanced sampling has been used to explore the detailed process of the detachment, the results of which indicate two potential pathways that are differentiated based upon the extent of water hydration. Here, the heights of the energy barriers depend upon the local morphology which influence the number of bridges (quasi-)simultaneously broken (1 or 2) or the Al-O coordination of the neighboring aluminum atoms (5 or 6) at the armchair edge. pH effects are significant, with a nearly 50% reduction in barrier height under alkaline conditions that are relevant to geothermal fluids and Al extraction from minerals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Self-re-adhering alkali-activated cement composite and its ability to mitigate corrosion of carbon steel in 300 °C hydrothermal environment

Cement-steel interface is a weak point of cement sheath integrity under the environments of high-temperature geothermal wells. This paper presents carbon steel (CS) adherence behaviors of 300 °C-autoclaved alkali-activated Calcium-Aluminate-Cement (CAC)/fly ash F (FAF) (Thermal Shock Resistant Cement, TSRC), granulated blast furnace slag (GBFS)/SiO 2 , and Ordinary Portland Cement (OPC)/SiO 2 blends. The composites’ ability to preserve the bond under the conditions of thermal shock (TS) and strong acid attack (pH 0.6 H 2 SO 4 /brine at 90 °C) as well as their ability to recover the damaged bond and provide steel corrosion protection after additional short-time 5-day curing at 300 °C were evaluated. GBFS/SiO 2 sheath underwent catastrophic failure in the first TS cycle; OPC/SiO 2 lost 78 % and TSRC 51 % of the bond strength in 6 cycles. Only TSRC-CS bond survived 30 days of strong acid exposure; OPC/SiO 2 bond failed after 18 days and GBFS/SiO 2 after 20 days. Addition of micro-glass fibers (MGF) to TSRC further improved its bond strength and CS corrosion protection. Samples of TSRC-CS cured for 30 days at 300 °C before the bond damage recovered 49 % of the damaged bond strength after additional short-time curing. The CS protected by the re-adhered TSRC showed low corrosion rate of 0.13 mm/year (TSRC-MGF), 0.2 mm/year (TSRC) vs. 0.64 mm/year for OPC/SiO 2 protected CS.

15 GEOTHERMAL ENERGY↗