Search NASA⌕ Search

SEARCH · Search NASA

Results for “ANECHOIC CHAMBERS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Comparison of advanced turboprop and conventional jet and propeller aircraft flyover noise annoyance: Preliminary results

A laboratory experiment was conducted to compare the flyover noise annoyance of proposed advanced turboprop aircraft with that of conventional turboprop and jet aircraft. The effects of fundamental frequency and tone-to-broadband noise ratio on advanced turboprop annoyance were also examined. A computer synthesis system is used to generate 18 realistic, time varying simulations of propeller aircraft takeoff noise in which the harmonic content is systematically varied to represent the factorial combinations of six fundamental frequencies ranging from 67.5 Hz to 292.5 Hz and three tone-to-broadband noise ratios of 0, 15, and 30 dB. These advanced turboprop simulations along with recordings of five conventional turboprop takeoffs and five conventional jet takeoffs are presented at D-weighted sound pressure levels of 70, 80, and 90 dB to 32 subjects in an anechoic chamber. Analyses of the subjects' annoyance judgments compare the three categories of aircraft and examine the effects of the differences in harmonic content among the advanced turboprop noises. The annoyance prediction ability of various noise measurement procedures and corrections is also examined.

Mccurdy, D. A.↗
NASA NTRS1986

Effects of initial condition on circular and elliptic jet noise

Noise produced by cold elliptic jets was studied experimentally using a 4 cm air jet in an anechoic chamber by varying the aspect ratio, nozzle exit boundary layer, and Mach number. Elliptic geometry is found to accentuate the sound produced by pairing of the shear layer vortices in the laminar boundary jet. Calculation of the pressure field produced by the pairing of elliptic vortex rings shows that the ratio of sound intensities produced by the pairing of inviscid elliptic vortex filament rings should be equal to their aspect ratio, the minor axis producing greater sound. Tripping the nozzle boundary layer changes the instability of the shear layer and removes the laminar vortices. If the sound produced by pairing and/or breakdown is considered to be the difference between laminar and turbulent jet noise, the pairing mechanism is seen to be very significant in laminar boundary layer jets.

Bridges, J. E.↗
NASA NTRS1985

Comparison of advanced turboprop and conventional jet and propeller aircraft flyover noise annoyance - Preliminary results

A laboratory experiment was conducted to compare the flyover noise annoyance of proposed advanced turboprop aircraft with that of conventional turboprop and jet aircraft. The effects of fundamental frequency and tone-to-broadband noise ratio on advanced turboprop annoyance were also examined. A computer synthesis system was used to generate 18 realistic, time varyring simulations of propeller aircraft takeoff noise in which the harmonic content was systematically varied to represent the factorial combinations of six fundamental frequencies ranging from 67.5 Hz to 292.5 Hz and three tone-to-broadband noise ratios of 0, 15, and 30 dB. These advanced turboprop simulations along with recordings of five conventional turboprop takeoffs and five conventional jet takeoffs were presented at D-weighted sound pressure levels of 70, 80, and 90 dB to 32 subjects in an anechoic chamber. Analyses of the subjects' annoyance judgments compare the three categories of aircraft and examine the effects of the differences in harmonic content among the advanced turboprop noises. The annoyance prediction ability of various noise measurement procedures and corrections is also examined.

Mccurdy, D. A.↗
NASA NTRS1986

Observations on the structure of an edge-tone flowfield

The unsteady flowfield in the region in which a rectangular jet interacts with the leading edge of a 20-deg wedge is investigated experimentally. Edge-tone flowfields at Mach 0.8 in the blowdown facility at Stanford University are recorded by phase-locked Schlieren photography using the apparatus and techniques described by Krothapalli and Horne (1984); detailed surface-pressure and velocity measurements are obtained at Mach 0.23 in the NASA Ames anechoic-chamber facility and presented graphically. It is shown that the jet-edge interaction produces a secondary vortex at the leading edge when an established shear layer or primary vortex is present, and that the primary and secondary vortices then evolve from a counterrotating vortex pair to a large single vortex which migrates along the wedge surface (in agreement with the observations of Rockwell et al., 1986). From a comparison with data on airfoil-trailing-edge flows (Satyanarayana, 1977) it is inferred that an instantaneous zero pressure differential is present at the leading edge of the wedge.

Krothapalli, A.↗
NASA NTRS1986

A study of radar cross section measurement techniques

Past, present, and proposed future technologies for the measurement of radar cross section were studied. The purpose was to determine which method(s) could most advantageously be implemented in the large microwave anechoic chamber facility which is operated at the antenna test range site. The progression toward performing radar cross section measurements of space vehicles with which the Orbital Maneuvering Vehicle will be called upon to rendezvous and dock is a natural outgrowth of previous work conducted in recent years of developing a high accuracy range and velocity sensing radar system. The radar system was designed to support the rendezvous and docking of the Orbital Maneuvering Vehicle with various other space vehicles. The measurement of radar cross sections of space vehicles will be necessary in order to plan properly for Orbital Maneuvering Vehicle rendezvous and docking assignments. The methods which were studied include: standard far-field measurements; reflector-type compact range measurements; lens-type compact range measurement; near field/far field transformations; and computer predictive modeling. The feasibility of each approach is examined.

Mcdonald, Malcolm W.↗
NASA NTRS1987

Experiments on reduction of propeller induced interior noise by active control of cylinder vibration

The feasibility of reducing interior noise caused by advanced turbo propellers by controlling the vibration of aircraft fuselages was investigated by performing experiments in an anechoic chamber with an aircraft model test rig and apparatus. It was found that active vibration control provides reasonable global attenuation of interior noise levels for the cases of resonant (at 576 Hz) and forced (at 708 Hz) system response. The controlling mechanism behind the effect is structural-acoustic coupling between the shell and the contained field, termed interface modal filtering.

Fuller, C. R.↗
NASA NTRS1988

Advanced turboprop aircraft flyover noise: Annoyance to counter-rotating-propeller configurations with an equal number of blades on each rotor, preliminary results

A laboratory experiment was conducted to quantify the annoyance of people to the flyover noise of advanced turboprop aircraft with counter-rotating propellers (CRP) having an equal number of blades on each rotor. The objectives were: to determine the effects of total content on annoyance; and compare annoyance to n x n CRP advanced turboprop aircraft with annoyance to conventional turboprop and jet aircraft. A computer synthesis system was used to generate 27 realistic, time-varying simulations of advanced turboprop takeoff noise in which the tonal content was systematically varied to represent the factorial combinations of nine fundamental frequencies and three tone-to-broadband noise ratios. These advanced turboprop simulations along with recordings of five conventional turboprop takeoffs and five conventional jet takeoffs were presented at three D-weighted sound pressure levels to 64 subjects in an anechoic chamber. Analyses of the subjects' annoyance judgments compare the three aircraft types and examined the effects of the differences in tonal content among the advanced turboprop noises. The annoyance prediction ability of various noise metrics is also examined.

Mccurdy, David A.↗
NASA NTRS1987

Measurement of the absorption coefficient of acoustical materials using the sound intensity method

In this study the possibility of using the two-microphone sound intensity technique to measure the normal incidence and the random incidence sound absorption coefficient was investigated. The normal incidence absorption coefficient was determined by measuring the intensity incidence on the sample and the intensity reflected by the sample placed in an anechoic chamber. The random incidence absorption coefficient was determined by measuring the intensity incident on the sample and the intensity reflected by the sample placed in a reverberation chamber. Absorption coefficient results obtained by the sound intensity technique were compared with standard techniques, namely the reverberation chamber and the standing wave tube. The major advantages of using the sound intensity technique are that it permits 'in situ' measurements and the absorption coefficient for a large range of frequencies can be obtained from a single measurement.

Atwal, Mahabir S.↗
NASA NTRS1989

Nonprincipal plane scattering of flat plates and pattern control of horn antennas

Using the geometrical theory of diffraction, the traditional method of high frequency scattering analysis, the prediction of the radar cross section of a perfectly conducting, flat, rectangular plate is limited to principal planes. Part A of this report predicts the radar cross section in nonprincipal planes using the method of equivalent currents. This technique is based on an asymptotic end-point reduction of the surface radiation integrals for an infinite wedge and enables nonprincipal plane prediction. The predicted radar cross sections for both horizontal and vertical polarizations are compared to moment method results and experimental data from Arizona State University's anechoic chamber. In part B, a variational calculus approach to the pattern control of the horn antenna is outlined. The approach starts with the optimization of the aperture field distribution so that the control of the radiation pattern in a range of directions can be realized. A control functional is thus formulated. Next, a spectral analysis method is introduced to solve for the eigenfunctions from the extremal condition of the formulated functional. Solutions to the optimized aperture field distribution are then obtained.

Balanis, Constantine A.↗
NASA NTRS1988

Advanced turboprop aircraft flyover noise: Annoyance to counter-rotating-propeller configurations with a different number of blades on each rotor: Preliminary results

A laboratory experiment was conducted to quantify the annoyance of people to the flyover noise of advanced turboprop aircraft with counter-rotating propellers (CRP) having a different number of blades on each rotor (nxm, e.g., 10 x 8, 12 x 11). The objectives were: (1) compare annoyance to nxm CRP advanced turboprop aircraft with annoyance to conventional turboprop and jet aircraft; (2) determine the effects of tonal content on annoyance; and (3) determine the ability of aircraft noise measurement procedures and corrections to predict annoyance for this new class of aircraft. A computer synthesis system was used to generate 35 realistic, time-varying simulations of advanced turboprop takeoff noise in which the tonal content was systematically varied to represent combinations of 15 fundamental frequency (blade passage frequency) combinations and three tone-to-broadband noise ratios. The fundamental frequencies, which represented blade number combinations from 6 x 5 to 13 x 12 and 7 x 5 to 13 x 11, ranged from 112.5 to 292.5 Hz. The three tone-to-broadband noise ratios were 0, 15, and 30 dB. These advanced turboprop simulations along with recordings of five conventional turboprop takeoffs and five conventional jet takeoffs were presented at D-weighted sound pressure levels of 70, 80, and 90 dB to 64 subjects in an anechoic chamber. Analyses of the subjects' annoyance judgments compare the three categories of aircraft and examine the effects of the differences in tonal content among the advanced turboprop noises. The annoyance prediction ability of various noise measurement procedures and corrections is also examined.

Mccurdy, David A.↗
NASA NTRS1990

Annoyance caused by advanced turboprop aircraft flyover noise: Counter-rotating-propeller configuration

Two experiments were conducted to quantify the annoyance of people to flyover noise of advanced turboprop aircraft with counter rotating propellers. The first experiment examined configurations having an equal number of blades on each rotor and the second experiment examined configurations having an unequal number of blades on each rotor. The objectives were to determine the effects on annoyance of various tonal characteristics, and to compare annoyance to advanced turboprops with annoyance to conventional turboprops and turbofans. A computer was used to synthesize realistic, time-varying simulations of advanced turboprop aircraft takeoff noise. The simulations represented different combinations fundamental frequency and tone-to-broadband noise ratio. Also included in each experiment were recordings of 10 conventional turboprop and turbofan takeoffs. Each noise was presented at three sound pressure levels in an anechoic chamber. In each experiment, 64 subjects judged the annoyance of each noise stimulus. Analyses indicated that annoyance was significantly affected by the interaction of fundamental frequency with tone-to-broadband noise ratio. No significant differences in annoyance between the advanced turboprop aircraft and the conventional turbofans were found. The use of a duration correction and a modified tone correction improved the annoyance prediction for the stimuli.

Mccurdy, David A.↗
NASA NTRS1990

Scattering measurements on natural and model trees

The acoustical back scattering from a simple scale model of a tree has been experimentally measured. The model consisted of a trunk and six limbs, each with 4 branches; no foliage or twigs were included. The data from the anechoic chamber measurements were then mathematically combined to construct the effective back scattering from groups of trees. Also, initial measurements have been conducted out-of-doors on a single tree in an open field in order to characterize its acoustic scattering as a function of azimuth angle. These measurements were performed in the spring, prior to leaf development. The data support a statistical model of forest scattering; the scattered signal spectrum is highly irregular but with a remarkable general resemblance to the incident signal spectrum. Also, the scattered signal's spectra showed little dependence upon scattering angle.

Rogers, James C.↗
NASA NTRS1990

Noise transmission characteristics of a large scale composite fuselage model

Results from an experimental test undertaken to study the basic noise transmission characteristics of a realistic, built-up composite fuselage model are presented. The floor-equipped stiffened composite cylinder was exposed to a number of different exterior noise source configurations in a large anechoic chamber. These exterior source configurations included two point sources located in the same plane on opposite sides of the cylinder, a single point source and a propeller simulator. The results indicate that the interior source field is affected strongly by exterior noise source phasing. Sidewall treatment is seen to reduce the overall interior sound pressure levels and dampen dominant acoustic resonances so that other acoustic modes can affect interior noise distribution.

Beyer, Todd B.↗
NASA NTRS1992

Almond-Shaped Test Body

Almond shaped test body developed for use in electromagnetic anechoic chamber for evaluation of range and measurement of components has low radar cross section that varies with angle over large dynamic range. Surface is composite formed by joining properly scaled ellipsoidal surfaces. Used to mount components whose radar cross sections are to be measured, and simulate backscatter characteristics of component as though it were over infinite ground plane.

Dominek, Allen↗
NASA NTRS1990

Correlating the EMC analysis and testing methods for space systems in MIL-STD-1541A

A study was conducted to improve the correlation between the electromagnetic compatibility (EMC) analysis models stated in MIL-STD-1541A and the suggested testing methods used for space systems. The test and analysis methods outlined in MIL-STD-1541A are described, and a comparative assessment of testing and analysis techniques as they relate to several EMC areas is presented. Suggestions on present analysis and test methods are introduced to harmonize and bring the analysis and testing tools in MIL-STD-1541A into closer agreement. It is suggested that test procedures in MIL-STD-1541A must be improved by providing alternatives to the present use of shielded enclosures as the primary site for such tests. In addition, the alternate use of anechoic chambers and open field test sites must be considered.

Perez, Reinaldo J.↗
NASA NTRS1992

Scattering effects of Space Station structure on Assembly/Contingency Subsystem (ACS) antenna performance

ACS antenna patterns were computed using the Geometrical Theory of Diffraction (GTD) modeling technique in which the multipath interference from the Space Station structures was included. The accuracy of the numerical results obtained is verified by comparing them against a series of RF anechoic chamber measurements. Less than 1 dB degradation is expected if a +/- 15 deg cone is used to protect the ACS high gain antenna boresight pattern; a +/- 20 deg cone is required if no more than 0.5 dB gain degradation is desired.

Hwu, Shian U.↗
NASA NTRS1992

A periodic moment method solution for TM scattering from lossy dielectric bodies with application to wedge absorber

The periodic moment method (PMM) solution for the scattering from two-dimensional lossy dielectric bodies is developed in this paper. The purpose is to design microwave wedge absorber for low reflectivity so that one can improve the performance of anechoic chamber measurements. With PMM, the reflection and transmission coefficients of periodically distributed bodies illuminated by a plane wave have been accurately calculated using a Cray Y-MP supercomputer. Through these studies, some wedge absorber configurations have been designed, fabricated, and then tested in the OSU/ESL compact range measurement facility. Two 8 in. commercial wedges, a curved wedge, and a four-layer wedge are studied in this paper. In all cases, good agreement between calculations and measurements has been obtained.

Yang, Chang-Fa↗