SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An outline is given of the mission objectives and requirements, system elements, system concepts, technology requirements and forecasting, and priority analysis for LANDSAT D. User requirements and mission analysis and technological forecasting are emphasized. Mission areas considered include agriculture, range management, forestry, geology, land use, water resources, environmental quality, and disaster assessment.
There are no author-identified significant results in this report.
A systems concept procedure is described for the optimization of acoustic duct liner design for both uniform and multisegment types. The concept was implemented by the use of a double reverberant chamber flow duct facility coupled with sophisticated computer control and acoustic analysis systems. The optimization procedure for liner insertion loss was based on the concept of variable liner impedance produced by bias air flow through a multilayer, resonant cavity liner. A multiple microphone technique for in situ wall impedance measurements was used and successfully adapted to produce automated measurements for all liner configurations tested. The complete validation of the systems concept was prevented by the inability to optimize the insertion loss using bias flow induced wall impedance changes. This inability appeared to be a direct function of the presence of a higher order energy carrying modes which were not influenced significantly by the wall impedance changes.
The relative strengths of those interactions which enable propulsive forces are listed as well as the specific impulse of various propellants. Graphics show the linear synchronous motor of the mass driver, the principle of the direct current electromagnetic launcher, and the characteristics of the rail gun.
Engine performance and mission studies were carried out for turbofan engines equipped with supersonic through-flow fans. The mission was for a commercial supersonic transport with a Mach 2.32 capability. The advantages of the supersonic fan engines are discussed in terms of mission range comparisons with other engine types. The effects of fan efficiency, inlet losses, and engine weight on engine performance and mission range are shown. The range of a supersonic transport with supersonic fan engines could be 10 to 20 percent better than with other types having the same technology core.
Engine performance and mission studies were conducted for a novel turbofan engine concept incorporating a supersonic through-flow fan, and comparisons were made with two supersonic transport (SST) engine concepts of equivalent thrust and technological sophistication. It was found that in the case of an SST with a cruise speed of Mach 2.32, the through-flow fan engine may yield ranges 10 to 20% greater than the two alternatives considered. The engine has a conventional core, with the supersonic fan being driven by a concentric low-pressure turbine that is uncoupled with the single, high pressure turbine/compressor core spool. Among the topics discussed are the methods of analysis employed and perturbation studies concerning supersonic fan adiabatic efficiency, fan discharge characteristics and propulsion system weight.
An exploratory point design study was carried out on a shuttle-launchable megawatt nuclear orbit transfer vehicle (OTV) with a 5000 kg payload capacity. The system, which consists of a fixed bed reactor, a Brayton cycle power conversion system, and a liquid droplet radiator (LDR) to reject heat, is deployable from a small package. The methods and technologies of this design are discussed, as well as critical design problems. While this is a preliminary study, it indicates that a space-nuclear reactor, combined with the LDR, make possible a continuous 10 MW(e) power station on orbit with a single shuttle launch.
The Airborne Imaging Spectrometer (AIS) is a multispectral infrared imaging instrument utilizing a 32- x 32-element mercury-cadmium-telluride detector array to achieve high spatial resolution. A novel optical design provides high spectral resolution, and, in conjunction with the 32-element spatial resolution, makes optimal use of the capabilities of the area array. The experiment requirements and the details of instrument design, implementation, and calibration are presented. The superior resolution, accuracy, and data acquisition rate of this sensor/instrument concept for reconnaissance and geophysical survey is detailed and plans for upgrading/improving the instrument and future applications of this design concept are discussed.
Explore the source record for details and available documents.
Over the past two decades, fiber optics has emerged as a highly practical and cost-efficient communications technology. Its competitiveness vis-a-vis other transmission media, especially satellite, has become a critical question. This report studies the likely evolution and application of fiber optic networks in the United States to the end of the century. The outlook for the technology of fiber systems is assessed and forecast, scenarios of the evolution of fiber optic network development are constructed, and costs to provide service are determined and examined parametrically as a function of network size and traffic carried. Volume 1 consists of the Executive Summary. Volume 2 focuses on fiber optic technology and long distance fiber optic networks. Volume 3 develops a traffic and financial model of a nationwide long distance transmission network. Among the study's most important conclusions are: revenue requirements per circuit for LATA-to-LATA fiber optic links are less than one cent per call minute; multiplex equipment, which is likely to be required in any competing system, is the largest contributor to circuit costs; the potential capacity of fiber optic cable is very large and as yet undefined; and fiber optic transmission combined with other network optimization schemes can lead to even lower costs than those identified in this study.
In this paper, preliminary qualitative and quantitative comparisons of the body weight of five hypersonic aircraft configurations are conducted. The five configurations are briefly described as follows: (1) a wing-and-body arrangement with a power-law, circular cross-section body and a delta wing; (2) an all-body vehicle with delta planform and elliptical cross-sections; (3) a wingless wave rider configuration; (4) a winged wave rider configuration; and (5) the spacewing concept, an oblique flying wing at low speed that yaws to 90 deg sweep and flies end-on at hypersonic speeds. The vehicles are defined by their external moldline geometries and by the interior arrangement of their fuel tanks and other components. Intersecting, circular-lobed tankage is used in vehicles with noncircular bodies. The nonusable volume of such concepts is calculated. The structural concept, structural materials, Thermal Protection System, and heat load are allowed to vary with vehicle longitudinal station. Relative strengths and weaknesses of the various hypersonic aircraft concepts in terms of body weight are summarized.
Information is given in viewgraph form on the Computational Fluid Dynamics (CFD) Workshop held July 14 - 16, 1987. Topics covered include the philosophy of CFD validation, current validation efforts, the wing-body-tail Euler code, F-20 Euler simulated oil flow, and Euler Navier-Stokes code validation for 2D and 3D nozzle afterbody applications.
The paper discusses the status of current and future commercial space opportunities. The goal is to pioneer innovative, customer-focused space concepts and technologies, leveraged through industrial, academic, and government alliance, to ensure U.S. commercial competitiveness and preeminence in space. The strategy is to develop technologies which enable new products and processes, deploy existing technology into commercial and military products and processes, and integrate military and commercial research and production activities. Technology development areas include information infrastructure, electronics design and manufacture, health care technology, environment technology, and aeronautical technologies.
A status report on current and future commercial space opportunities is presented.
The Missile Defense Agency (MDA) (formerly the Ballistic Missile Defense Organization) is embarking on a program to employ the use of High Altitude Airships (HAAs) for surveillance of coastal areas as a part of homeland defense. It is envisioned that these HAAs will fly at 70,000 feet continuously for at least a year, therefore requiring a regenerative electric power system. As part of a program to entice the MDA to utilize the NASA GRC expertise in electric power and propulsion as a means of risk reduction, an internal study program was performed to examine possible configurations that may be employed on a HAA to meet a theoretical surveillance need. This entailed the development of a set of program requirements which were flowed down to system and subsystem level requirements as well as the identification of environmental and infrastructure constraints. Such infrastructure constraints include the ability to construct a reasonably sized HAA within existing airship hangers, as the size of such vehicles could reach in excess of 600 ft. The issues regarding environments at this altitude are similar to those that would be imposed on satellite in Low Earth Orbit. Additionally, operational constraints, due to high winds at certain times of the year were also examined to determine options that could be examined to allow year round coverage of the US coast.
The goal of this publication is to provide an overview of the topic of revolutionary research in aeronautics at Langley, including many examples of research efforts that offer significant potential benefits, but have not yet been applied. The discussion also includes an overview of how innovation and creativity is stimulated within the Center, and a perspective on the future of innovation. The documentation of this topic, especially the scope and experiences of the example research activities covered, is intended to provide background information for future researchers.
Boeing, with Pratt & Whitney, General Electric, Rolls-Royce, M4 Engineering, Wyle Laboratories and Georgia Institute of Technology, conducted a study of supersonic commercial aircraft concepts and enabling technologies for the year 2030-2035 timeframe. The work defined the market and environmental/regulatory conditions that could evolve by the 2030/35 time period, from which vehicle performance goals were derived. Relevant vehicle concepts and technologies are identified that are anticipated to meet these performance and environmental goals. A series of multidisciplinary analyses trade studies considering vehicle sizing, mission performance and environmental conformity determined the appropriate concepts. Combinations of enabling technologies and the required technology performance levels needed to meet the desired goals were identified. Several high priority technologies are described in detail, including roadmaps with risk assessments that outline objectives, key technology challenges, detailed tasks and schedules and demonstrations that need to be performed. A representative configuration is provided for reference purposes, along with associated performance estimates based on these key technologies.
No abstract available