Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aerodynamic configurations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Hypersonic aerodynamics test facility using the external propulsion accelerator

The use of the External propulsion Accelerator (EPA) for launching models of hypersonic aerodynamic configurations into an instrumented ballistic range is discussed. The aerodynamic model is encased inside an axisymmetric projectile designed to be accelerated to high speed in the EPA. Accelerator lengths required to achieve hypersonic speeds are estimated to vary from 10 meters for Mach 7, 40 meters for Mach 10, 150 meters for Mach 15, and 700 meters for Mach 30, assuming a limit of 50,000 g's acceleration. For a model span of 10 cm to 25 cm, the launch tube diameters are 40 cm and 100 cm, respectively. Using this EPA launcher will enable exact simulation of hypersonic flight in ground facilities where both the gas composition and pressure can be controlled in the ballistic range.

Rom, J.↗
NASA NTRS2002

Supersonic Aerodynamic Characteristics of Proposed Mars '07 Smart Lander Configurations

Supersonic aerodynamic data were obtained for proposed Mars '07 Smart Lander configurations in NASA Langley Research Center's Unitary Plan Wind Tunnel. The primary objective of this test program was to assess the supersonic aerodynamic characteristics of the baseline Smart Lander configuration with and without fixed shelf/tab control surfaces. Data were obtained over a Mach number range of 2.3 to 4.5, at a free stream Reynolds Number of 1 x 10(exp 6) based on body diameter. All configurations were run at angles of attack from -5 to 20 degrees and angles of sideslip of -5 to 5 degrees. These results were complemented with computational fluid dynamic (CFD) predictions to enhance the understanding of experimentally observed aerodynamic trends. Inviscid and viscous full model CFD solutions compared well with experimental results for the baseline and 3 shelf/tab configurations. Over the range tested, Mach number effects were shown to be small on vehicle aerodynamic characteristics. Based on the results from 3 different shelf/tab configurations, a fixed control surface appears to be a feasible concept for meeting aerodynamic performance metrics necessary to satisfy mission requirements.

Murphy, Kelly J.↗
NASA NTRSDate not supplied

Novel Tilting Ducted-Fan Aerial Vehicle Configurations

There has been recent renewed interested in ducted-fan, powered-lift vertical takeoff and landing aircraft vehicles for uninhabited aerial vehicle and urban aerial mobility aerial applications. Early work was conducted in the 1950’s to the late 1980’s into ducted-fan vehicles, especially at the time for military missions. The focus of ducted-fan research began to shift to UAV’s and personal air transportation in the 2000’s. Work in the early 2000’s fostered interest into ducted-fan aerial vehicles for vertical lift planetary aerial vehicle missions, especially for missions to Titan, a moon of Saturn. For example, early work at NASA Ames conducted the first known investigation into oval ducts (with internal tandem fans) to be used for these aerial vehicles. The use of twin oval ducts (with internal tandem fans) allowed the use of quadrotor-style rotor rpm control for vehicle trim (in hover, for transition to high-speed forward flight the addition of a tilt-actuator to pitch the twin oval ducts forward to be aligned with the freestream needed to be added to the control approach. This current study explores open-rotor, single isolated ducted-fan, and full vehicle configuration aerodynamic performance for hover, transition, and cruise regimes for novel tilting ducted-fan aerial vehicle configurations. The objective of this study is to better understand the design aerodynamics trade space for noncircular tilting ducted-fans. The primary analysis tool used in this paper is the mid-fidelity computational fluid dynamics RotCFD tool. Several interesting and largely unexplored rotor-on-rotor (or fan-on-fan), duct-on-rotor, rotor- on-duct, and duct-on-airframe are examined in this paper. Many of these aerodynamic interactions are the key to overall aerial vehicle performance. Limited parametric sweeps of rotor-to-rotor spacing (and, therefore, sizing and shape of the enveloping ducts) for the various duct configurations will also be performed. The trade-offs between duct thrust augmentation in hover versus improved transition controllability versus improved cruise L/D will be discussed for various novel duct configurations. These ducted-fan configurations include oval ducts, ‘figure-eight’ ducts, and ‘B-shaped’ ducts, among others.

Ducted-Fan↗
NASA NTRS1974

Non-engine aerodynamic noise investigation of a large aircraft

A series of flyover noise measurements have been accomplished utilizing a large jet transport aircraft with engine power reduced to flight idle. It was determined that the aerodynamic (nonengine) noise levels did occur in the general range that had been predicted by using small aircraft (up to 17,690 kg gross weight) prediction techniques. The test procedures used are presented along with discussions of the effects of aerodynamic configuration on the radiated noise, identification of noise sources, and predicted aerodynamic noise as compared with measurements.

Gibson, J. S.↗
NASA NTRS1988

The effect of spatial wind gradients on airplane aerodynamics

An account is given of the results of recent studies of the effect of a spatially sheared wind field on airplane aerodynamics; the wind shear was computed by a modified vortex-lattice computer program, and characterized through the formulation of wind shear aerodynamic coefficients. The magnitude of the aerodynamic effect was demonstrated by computing the change in conventional wing/tail configuration aerodynamics for a fixed flight path through a simulated microburst. A substantial portion of the control authority of the aircraft may be required to counteract the wind shear-induced forces and moments in the microburst environment; both aperiodic and oscillatory instabilities may be generated by shear-dependent dynamic modes.

Vicroy, Dan D.↗
NASA NTRS1995

Implementation of a multiblock sensitivity analysis method in numerical aerodynamic shape optimization

A multiblock sensitivity analysis method is applied in a numerical aerodynamic shape optimization technique. The Sensitivity Analysis Domain Decomposition (SADD) scheme which is implemented in this study was developed to reduce the computer memory requirements resulting from the aerodynamic sensitivity analysis equations. Discrete sensitivity analysis offers the ability to compute quasi-analytical derivatives in a more efficient manner than traditional finite-difference methods, which tend to be computationally expensive and prone to inaccuracies. The direct optimization procedure couples CFD analysis based on the two-dimensional thin-layer Navier-Stokes equations with a gradient-based numerical optimization technique. The linking mechanism is the sensitivity equation derived from the CFD discretized flow equations, recast in adjoint form, and solved using direct matrix inversion techniques. This investigation is performed to demonstrate an aerodynamic shape optimization technique on a multiblock domain and its applicability to complex geometries. The objectives are accomplished by shape optimizing two aerodynamic configurations. First, the shape optimization of a transonic airfoil is performed to investigate the behavior of the method in highly nonlinear flows and the effect of different grid blocking strategies on the procedure. Secondly, shape optimization of a two-element configuration in subsonic flow is completed. Cases are presented for this configuration to demonstrate the effect of simultaneously reshaping interfering elements. The aerodynamic shape optimization is shown to produce supercritical type airfoils in the transonic flow from an initially symmetric airfoil. Multiblocking effects the path of optimization while providing similar results at the conclusion. Simultaneous reshaping of elements is shown to be more effective than individual element reshaping due to the inclusion of mutual interference effects.

Lacasse, James M.↗
NASA NTRS1979

An experimental investigation of the effect of rotor tip shape on helicopter blade-slap noise

The effect of tip-shape modification on blade-vortex interaction-induced helicopter blade-slap noise was investigated. The general rotor model system (GRMS) with a 3.148 m (10.33 ft) diameter, four-bladed fully articulated rotor was installed in the Langley V/STOL wind tunnel. The tunnel was operated in the open-throat configuration with treatment to improve the semi-anechoic characteristics of the test chamber. Based on previous investigation, four promising tips (ogee, sub-wing, 60 deg swept-tapered, and end-plate) were used along with a standard square tip as a baseline configuration. Aerodynamic and acoustical data concerning the relative applicability of the various tip configurations for blade-slap noise reduction are presented without analysis or discussion.

Hoad, D. R.↗
NASA NTRS2013

Benefits of Hybrid-Electric Propulsion to Achieve 4x Increase in Cruise Efficiency for a VTOL Aircraft

Electric propulsion enables radical new vehicle concepts, particularly for Vertical Takeoff and Landing (VTOL) aircraft because of their significant mismatch between takeoff and cruise power conditions. However, electric propulsion does not merely provide the ability to normalize the power required across the phases of flight, in the way that automobiles also use hybrid electric technologies. The ability to distribute the thrust across the airframe, without mechanical complexity and with a scale-free propulsion system, is a new degree of freedom for aircraft designers. Electric propulsion is scale-free in terms of being able to achieve highly similar levels of motor power to weight and efficiency across a dramatic scaling range. Applying these combined principles of electric propulsion across a VTOL aircraft permits an improvement in aerodynamic efficiency that is approximately four times the state of the art of conventional helicopter configurations. Helicopters typically achieve a lift to drag ratio (L/D) of between 4 and 5, while the VTOL aircraft designed and developed in this research were designed to achieve an L/D of approximately 20. Fundamentally, the ability to eliminate the problem of advancing and retreating rotor blades is shown, without resorting to unacceptable prior solutions such as tail-sitters. This combination of concept and technology also enables a four times increase in range and endurance while maintaining the full VTOL and hover capability provided by a helicopter. Also important is the ability to achieve low disc-loading for low ground impingement velocities, low noise and hover power minimization (thus reducing energy consumption in VTOL phases). This combination of low noise and electric propulsion (i.e. zero emissions) will produce a much more community-friendly class of vehicles. This research provides a review of the concept brainstorming, configuration aerodynamic and mission analysis, as well as subscale prototype construction and flight testing that verifies transition flight control. A final down-selected vehicle is also presented.

Fredericks, William J.↗
NASA NTRS1980

Generic aerocapture atmospheric entry study, volume 1

An atmospheric entry study to fine a generic aerocapture vehicle capable of missions to Mars, Saturn, and Uranus is reported. A single external geometry was developed through atmospheric entry simulations. Aerocapture is a system design concept which uses an aerodynamically controlled atmospheric entry to provide the necessary velocity depletion to capture payloads into planetary orbit. Design concepts are presented which provide the control accuracy required while giving thermal protection for the mission payload. The system design concepts consist of the following elements: (1) an extendable biconic aerodynamic configuration with lift to drag ratio between 1.0 and 2.0; (2) roll control system concepts to control aerodynamic lift and disturbance torques; (3) aeroshell design concepts capable of meeting dynamic pressure loads during aerocapture; and (4) entry thermal protection system design concepts to meet thermodynamic loads during aerocapture.

Source record↗
NASA NTRS1974

Experimental aerodynamic characteristics for a cylindrical body of revolution with various noses at angles of attack from 0 deg to 58 deg and Mach numbers from 0.6 to 2.0

An experimental investigation was conducted to determine the effect of forebody geometry, a grit ring around the nose, Reynolds number, Mach number, and angle of attack on the aerodynamic characteristics of a body of revolution. Aerodynamic force and moment characteristics were measured for a cylindrical body with tangent ogive noses of fineness ratio 2.5, 3.0, 3.5, and 5.0. The cylindrical body was tested with an ogive nose having a rounded tip and an ogive nose with two different nose strake arrangements. Aerodynamic configurations were tested at various Mach numbers, angles of attack, and Reynolds numbers. The data demonstrate that the aerodynamic characteristics for a body of revolution can be significantly affected by changes in nose fineness ratio, nose bluntness, Reynolds number, Mach number, and, of course, angle of attack. Nose strakes increased the normal forces but had little effect on the side forces that developed at subsonic Mach numbers for alpha greater than about 25. A grit ring around the nose had little or no effect on the aerodynamic characteristics.

Jorgensen, L. H.↗
NASA NTRS1985

A simplified guidance algorithm for lifting aeroassist orbital transfer vehicles

The derivation, logic, and performance of a simplified atmospheric guidance algorithm for aeroassist orbital-transfer vehicles (AOTVs) are presented. The algorithm was developed to meet the demands for an aerobraking trajectory guidance technique that was uncomplicated, easily integrated into existing trajectory programs, adaptable to a range of vehicle aerodynamic configurations, capable of performance equivalent to currently available guidance programs in compensating for dispersions in entry conditions, atmospheric conditions, and aerodynamic characteristics. The result was a hybrid lifting guidance algorithm combining the method of reference-profile generation with the method of predictor/corrector schemes. The resulting performance is good (less than 3 n.m. error from desired apogee despite uncertainties of + or - 50 percent atmospheric density, + or - 0.2 deg entry flight-path angle, or + or - 50 percent L/D. Combinations of these same dispersions with lesser magnitudes have also been successful, although performance with density 'pockets' within the atmosphere requires more analysis.

Cerimele, C. J.↗
NASA NTRS2002

Aerodynamic Database Development for Mars Smart Lander Vehicle Configurations

An aerodynamic database has been generated for the Mars Smart Lander Shelf-All configuration using computational fluid dynamics (CFD) simulations. Three different CFD codes, USM3D and FELISA, based on unstructured grid technology and LAURA, an established and validated structured CFD code, were used. As part of this database development, the results for the Mars continuum were validated with experimental data and comparisons made where applicable. The validation of USM3D and LAURA with the Unitary experimental data, the use of intermediate LAURA check analyses, as well as the validation of FELISA with the Mach 6 CF(sub 4) experimental data provided a higher confidence in the ability for CFD to provide aerodynamic data in order to determine the static trim characteristics for longitudinal stability. The analyses of the noncontinuum regime showed the existence of multiple trim angles of attack that can be unstable or stable trim points. This information is needed to design guidance controller throughout the trajectory.

Bobskill, Glenn J.↗
NASA NTRS1985

The space shuttle launch vehicle aerodynamic verification challenges

The Space Shuttle aerodynamics and performance communities were challenged to verify the Space Shuttle vehicle (SSV) aerodynamics and system performance by flight measurements. Historically, launch vehicle flight test programs which faced these same challenges were unmanned instrumented flights of simple aerodynamically shaped vehicles. However, the manned SSV flight test program made these challenges more complex because of the unique aerodynamic configuration powered by the first man-rated solid rocket boosters (SRB). The analyses of flight data did not verify the aerodynamics or performance preflight predictions of the first flight of the Space Transportation System (STS-1). However, these analyses have defined the SSV aerodynamics and verified system performance. The aerodynamics community also was challenged to understand the discrepancy between the wind tunnel and flight defined aerodynamics. The preflight analysis challenges, the aerodynamic extraction challenges, and the postflight analyses challenges which led to the SSV system performance verification and which will lead to the verification of the operational ascent aerodynamics data base are presented.

Wallace, R. O.↗
NASA NTRS1989

Aerodynamic characteristics of proposed assured crew return capability (ACRC) configurations

The aerodynamic characteristics of seven reentry configurations suggested as possible candidate vehicles to return crew members from the U.S. Space Station Freedom to earth has been reviewed. The shapes varied from those capable of purely ballistic entry to those capable of gliding entry and fromk parachute landing to conventional landing. Data were obtained from existing (published and unpublished) sources and from recent wind tunnel tests. The lifting concepts are more versatile and satisfy all the mission requirements. Two of the lifting shapes studied appear promising - a lifting body and a deployable wing concept. The choice of an ACRC concept, however, will be made after all factors involving transportation from earth to orbit and back to earth again have been weighed.

Ware, George M.↗
NASA NTRS1981

PAN AIR: A computer program for predicting subsonic or supersonic linear potential flows about arbitrary configurations using a higher order panel method. Volume 3: Case manual (version 1.0)

Numerous applications of the PAN AIR computer program system are presented. PAN AIR is user-oriented tool for analyzing and/or designing aerodynamic configurations in subsonic or supersonic flow using a technique generally referred to as a higher order panel method. Problems solved include simple wings in subsonic and supersonic flow, a wing-body in supersonic flow, wing with deflected flap in subsonic flow, design of two-dimensional and three-dimensional wings, axisymmetric nacelle in supersonic flow, and wing-canard-tail-nacelle-fuselage combination in supersonic flow.

Medan, R. T.↗