Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aerodynamic efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Adaptive Load Control of Flexible Aircraft Wings Using Fiber Optic Sensing

Over the past century aircraft wing design has transformed from the morphing wing used on the Wright Flyer to rigid wings with little to no shape-tailoring abilities. Modern day wings are designed to fly at a single trim condition and optimized to have a maximum aerodynamic efficiency at only this condition. Shape morphing wings on the other hand have the potential to undergo geometric changes allowing them to adapt to their mission profiles. Several flight demonstrations have been conducted over the decades using morphing-wing technologies. Active wing-twist control was demonstrated on the X-53 Active Aeroelastic Wing (AAW) research project by utilizing multiple leading- and trailing-edge control surfaces. Passive morphing technology has been demonstrated on the Rockwell RPRV-870 Highly Maneuverable Aircraft Technology (HiMAT) aircraft. In the current study, the wings of a small unmanned aerial system (sUAS) were modified to have segmented control surfaces (SCS). The modifications include segmenting the original wing control surfaces (one flap and one aileron per wing) into 44 individual sections, each section having its own independent servo control motor. The wings were also instrumented with a network of over 1800 fiber-optic strain sensors (on four sensing fibers distributed over the top and bottom surfaces of the wing) monitoring the strain response of the wing to aerodynamic loading. The SCS positions were manipulated in real time to modify the spanwise lift distribution of the wings on the sUAS. The change in the structural response of the wings caused by load redistribution was quantified by measuring the bending strains on the upper and lower wing surfaces using an on-board compact fiber-optic strain sensing (cFOSS) system. A feedback controller was developed to control the SCS positions using strain-based shape estimations from the Displacement Transfer Function (DTF). Post-processing of the strain data allowed for the transverse displacement distributions and load distributions to be compared for the conventional and segmented control surface cases using displacements and loads algorithms developed by Richards and Ko at AFRC (refs. 5-10). While the current study focused on the shifting of the spanwise aerodynamic loads as quantified by displacements, future applications for loads or displacement control might include active gust alleviation and flutter suppression.

Pena, Francisco↗
NASA NTRS2014

A Modular Aerospike Engine Design Using Additive Manufacturing

A modular aerospike engine concept has been developed with the objective of demonstrating the viability of the aerospike design using additive manufacturing techniques. The aerospike system is a self-compensating design that allows for optimal performance over the entire flight regime and allows for the lowest possible mass vehicle designs. At low altitudes, improvements in Isp can be traded against chamber pressure, staging, and payload. In upper stage applications, expansion ratio and engine envelope can be traded against nozzle efficiency. These features provide flexibility to the System Designer optimizing a complete vehicle stage. The aerospike concept is a good example of a component that has demonstrated improved performance capability, but traditionally has manufacturing requirements that are too expensive and complex to use in a production vehicle. In recent years, additive manufacturing has emerged as a potential method for improving the speed and cost of building geometrically complex components in rocket engines. It offers a reduction in tooling overhead and significant improvements in the integration of the designer and manufacturing method. In addition, the modularity of the engine design provides the ability to perform full scale testing on the combustion devices outside of the full engine configuration. The proposed design uses a hydrocarbon based gas-generator cycle, with plans to take advantage of existing powerhead hardware while focusing DDT&E resources on manufacturing and sub-system testing of the combustion devices. The major risks for the modular aerospike concept lie in the performance of the propellant feed system, the structural integrity of the additive manufactured components, and the aerodynamic efficiency of the exhaust flow.

Peugeot, John↗
NASA NTRS1974

Results from cascade thrust reverser noise and suppression experiments

Results from experimental work on model scale cascade reversers with cold airflow are presented. Sound power level directivity and spectral characteristics for cascade reversers are reported. Effect of cascade exit area ratio, vane profile shape, and emission arc are discussed. Model equivalent diameters varied from 3 to 5 inches, pressure ratios range from 1.15 to 3.0. Depending on the reverser type, acoustic power was proportional to the 4 1/2 to 6th power of ideal jet velocity. Reverser noise peaked at higher frequency and was more omnidirectional than nozzle-alone jet noise. Appreciable reduction in sideline noise was obtained from plane shields. Airfoil-vaned cascades were the most aerodynamically efficient and least noisy reversers. Scaling of cascade reverser data to example aircraft engines showed all cascades above the 95 PNdB sideline goal from STOL aircraft. However, the airfoil-vaned reverser has a good potential for meeting this goal for high-bypass (low pressure ratio) exhausts.

Gutierrez, O. A.↗
NASA NTRS1974

Advanced supersonic transport design developments

Advanced technology studies have indicated a major payload/range improvement for the next generation supersonic transport while meeting stringent environmental requirements. The major technology advance is the variable-cycle engine. When integrated with efficient aerodynamic and structural concepts, the variable-cycle engine airplane will attain a design range of 5500 nautical miles with no penalty for take-off noise or subsonic missions. The goal - not achievable in past programs - will allow one airplane to compete subsonic in over-land sonic boom prohibited areas as well as over-water supersonic routes. This goal will not be achieved without an aggressive technology development program.

Driver, C.↗
NASA NTRS1974

Impeller blade design method for centrifugal compressors

The design of a centrifugal impeller with blades that are aerodynamically efficient, easy to manufacture, and mechanically sound is discussed. The blade design method described here satisfies the first two criteria and with a judicious choice of certain variables will also satisfy stress considerations. The blade shape is generated by specifying surface velocity distributions and consists of straight-line elements that connect points at hub and shroud. The method may be used to design radially elemented and backward-swept blades. The background, a brief account of the theory, and a sample design are described.

Jansen, W.↗
NASA NTRS1974

Transonic transport wings - Oblique or swept

Oblique-wing twin- and single-fuselage transonic transport models were wind tunnel tested and showed superior aerodynamic efficiency to that of fixed-swept-wing, variable-sweep-wing, and delta-wing configurations similarly tested. The oblique-wing airplane had the smallest gross weight and lowest fuel consumption; it could achieve lower noise levels than swept- and delta-wing aircraft by engine-nacelle treatment; and it was aeroelastically less stable than a sweptback wing but more stable than a swept-forward wing. Graphite-epoxy met stability requirements without additional stiffening, whereas aluminum needed some additional stiffness. Further studies are called for to develop the full potential of the oblique-wing concept.

Jones, R. T.↗
NASA NTRS1975

Theoretical performance of cross-wind axis turbines with results for a catenary vertical axis configuration

A general analysis capable of predicting performance characteristics of cross-wind axis turbines was developed, including the effects of airfoil geometry, support struts, blade aspect ratio, windmill solidity, blade interference and curved flow. The results were compared with available wind tunnel results for a catenary blade shape. A theoretical performance curve for an aerodynamically efficient straight blade configuration was also presented. In addition, a linearized analytical solution applicable for straight configurations was developed. A listing of the computer program developed for numerical solutions of the general performance equations is included in the appendix.

Muraca, R. J.↗
NASA NTRS1976

Wing planforms for high-speed flight

The analysis indicates that for aerodynamic efficiency, wings designed for flight at supersonic speeds should be swept back at an angle greater than the Mach angle and the angle of sweepback should be such that the component of velocity normal to the leading edge is less than the critical speed of the airfoil sections. This principle may also be applied to wings designed for subsonic speeds near the speed of sound, for which the induced velocities resulting from the thickness might otherwise be sufficiently great to cause shock waves.

Jones, R. T.↗
NASA NTRS1976

The NASA structures and materials research program for supersonic cruise aircraft

The structures and materials part of the NASA Supersonic Cruise Aircraft Research (SCAR) program is reviewed. It is pointed out that in more than three years of work significant new technology has been generated. The aircraft configurations which are efficient aerodynamically have aeroelastic problems that must be alleviated by configuration changes, active controls, or additional structural mass. An approach involving the application of advanced composite materials has the highest potential for structural weight reduction. Attention is given to the structural concepts for an arrow-wing supersonic aircraft and the techniques used in the investigations. It is expected that continuing research in SCAR structures and materials should bring high payoffs in the late 1980s.

Cooper, P. A.↗
NASA NTRS1976

Propulsive-lift concepts for improved low-speed performance of supersonic cruise arrow-wing configurations

Low-aspect-ratio highly swept arrow-wing supersonic aircraft possess high levels of aerodynamic efficiency at supersonic cruising speeds, however, their inherently poor low-speed lift characteristics require design constraints that compromise supersonic performance. The data discussed in this paper were obtained in wind tunnel tests with supersonic crusing configurations, in which propulsive-lift concepts were used to improve low-speed performance. The data show that the increased low-speed lift provided by propulsive-lift permits reduction of both wing size and installed thrust. This yields a batter engine/airframe match for improved supersonic cruise efficiency and range, while still providing acceptable take-off field lengths.

Coe, P. L., Jr.↗
NASA NTRS1976

Summary of NASA aerodynamic and heat transfer studies in turbine vanes and blades

Aerodynamic effects of trailing edge geometry, hole size, angle, spacing, and shape were studied in two- and three-dimensional cascades and in a warm turbine test series. Heat transfer studies were carried out in various two- and three-dimensional test facilities in order to provide corresponding heat transfer data. Results are shown in terms of cooling effectiveness and aerodynamic efficiency for various coolant fractions, coolant-primary temperature ratios, and cooling configurations.

Moffitt, T. P.↗
NASA NTRS1976

Performance and benefits of an advanced technology supersonic cruise aircraft

The results of four years research on technology are synthesized in an advanced supersonic cruise aircraft design. Comparisons are presented with the former United States SST and the British-French Concorde, including aerodynamic efficiency, propulsion efficiency, weight efficiency, and community noise. Selected trade study results are presented on the subjects of design cruise Mach number, engine cycle selection, and noise suppression. The critical issue of program timing is addressed and some observations made regarding the impact that timing has on engine selection and minimization of program risk.

Fitzsimmons, R. D.↗
NASA NTRS1976

Summary of NASA aerodynamic and heat transfer studies in turbine vanes and blades

Aerodynamic effects of trailing edge geometry, hole size, angle, spacing, and shape have been studied in two- and three-dimensional cascades and in a warm turbine test series. Heat transfer studies have been carried out in various two- and three-dimensional test facilities in order to provide corresponding heat transfer data. Results are shown in terms of cooling effectiveness and aerodynamic efficiency for various coolant fractions, coolant-primary temperature ratios, and cooling configurations.

Moffitt, T. P.↗
NASA NTRS1977

Drag evaluation of the Bellanca Skyrocket II

The Bellanca Skyrocket II, possessor of five world speed records, is a single engine aircraft with high performance that has been attributed to a laminar flow airfoil and an all composite structure. Utilization of composite materials in the Skyrocket II is unique since this selection was made to increase the aerodynamic efficiency of the aircraft. Flight tests are in progress to measure the overall aircraft drag and the wing section drag for comparison with the predicted performance of the Skyrocket. Initial results show the zero lift drag is indeed low, equalling 0.016.

Gregorek, G. M.↗
NASA NTRS1978

Two-dimensional cold-air cascade study of a film-cooled turbine stator blade. 4: Comparison of experimental and analytical aerodynamic results for blade with 12 rows of 0.076-centimeter-(0.030-inch-) diameter holes having streamwise ejection angles

Previously published experimental aerodynamic efficiency results for a film cooled turbine stator blade are compared with analytical results computed from two published analytical methods. One method was used as published; the other was modified for certain cases of coolant discharge from the blade suction surface. For coolant ejection from blade surface regions where the surface static pressures are higher than the blade exit pressure, both methods predict the experimental results quite well. However, for ejection from regions with surface static pressures lower than the blade exit pressure, both methods predict too small a change in efficiency. The modified method gives the better prediction.

Prust, H. W., Jr.↗