Search NASA⌕ Search

SEARCH · Search NASA

Results for “Axial Jet”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Mass and Momentum Transport Experiments with Swirling Flow

An experimental study of mixing downstream of axial and swirling coaxial jets is being conducted to obtain data for the evaluation and improvement of turbulent transport models currently employed in a variety of computational procedures used throughout the propulsion community. The axial coaxial jet study was completed under Phase 1. The swirling coaxial jet study, which is the subject of this paper, was conducted under Phase 2 of the contract. A TEACH code was acquired, checked out for several test cases, and is reported. A study to measure length scales and to obtain a limited number of measurements with a blunt trailing edge inlet is being conducted under Phase 3 of the contract.

Johnson, B. V.↗
NASA NTRS1982

A comparison of turbulence intensity measurements using a laser velocimeter and a hot wire in a low speed jet flow

The study involves a simultaneous measurement with both instruments along radial scans at two axial locations in the jet exiting from the turbulent pipe and an axial scan at the 75-percent radial location in the jet from the convergent nozzle. The results suggest that, within the limits of flow stationarity, both instruments yield measurements in good agreement, + or - 0.8-percent in turbulence intensity, below a turbulence intensity (the ensemble standard deviation divided by the local mean velocity) of 20 percent. From turbulence intensities of 20 percent to a maximum of 75 percent, the measurements exhibit the same trends; for reasons discussed here, however, the comparisons are not of the quality as those below 20 percent. It is found that correcting the turbulence intensity data for velocity bias errors increases the results by an average of 2 percent in turbulence intensity above the hot wire results and the uncorrected laser velocimeter data. The results are seen as calling into question the validity of using the velocity bias correction and time average techniques for turbulence intensity measurements.

Meyers, J. F.↗
NASA NTRS1992

A numerical model for coupling between atomization and spray dynamics in liquid rocket thrust chambers

This paper describes a novel method of coupling the atomization and spray combustion processes encountered in coaxial injection elements of liquid rocket engine thrust chambers. This method is based on the Jet-Embedding technique in which the liquid jet core equations and the gas phase equations are solved separately. The liquid and gas phase solutions, however, are coupled through the boundary conditions at the interface between the phases. The computational grid for the gas phase calculations are adapted to the shape of the liquid jet core. The axial variation of droplet sizes are calculated using a stability analysis appropriate for the atomization regime of liquid jet breakup. The predictions of this method have been validated with experimental data on low speed water jets. Using this method, calculations are performed for the SSME fuel preburner single injector flow field. The results obtained are in good agreement with the predictions of the volume-of-fluid method.

Giridharan, M. G.↗
NASA NTRS1990

Experimental investigation of a single flush-mounted hypermixing nozzle

The results of an experimental wind tunnel investigation of a circular supersonic jet (m sub j = 3.47) injected at a 10 degree angle into a supersonic freestream. The jet penetrates a boundary layer, which has a thickness approximately the same as the jet nozzle exit diameter. Measurements were made for nominal freestream Mach numbers of 1.6, 2.0, 2.5, and 3.0. Three jet total pressures were run at each freestream Mach number, resulting in twelve separate operating conditions. Mean data accumulated by means of static and total pressure probe instrumentation are presented at two axial stations: seven jet nozzle diameters upstream and 15 jet nozzle diameters downstream from where the centerline of the nozzle intersects the wind tunnel wall. For one condition at each freestream Mach number, the jet air was seeded with a hydrocarbon trace gas and the flow was sampled at the downstream measurement plane to quantify the mean mixing of the two streams. Surface oil flow visualization was also used to investigate the flow interaction. All results are for air-to-air mixing. The measurements indicate the presence of two pairs contra-rotating vortices. One pair follows the jet trajectory and tends to split the jet into two streams. A smaller pair, rotating in an opposite sense, develops in the near wall region. Reported results include Mach number and volume fraction distributions in the cross plane, as well as jet penetration and mixing efficiency.

Davis, David O.↗
NASA NTRS2015

An Empirical Jet-Surface Interaction Noise Model with Temperature and Nozzle Aspect Ratio Effects

An empirical model for jet-surface interaction (JSI) noise produced by a round jet near a flat plate is described and the resulting model evaluated. The model covers unheated and hot jet conditions (1 less than or equal to jet total temperature ratio less than or equal to 2.7) in the subsonic range (0.5 less than or equal to M(sub a) less than or equal to 0.9), surface lengths 0.6 less than or equal to (axial distance from jet exit to surface trailing edge (inches)/nozzle exit diameter) less than or equal to 10, and surface standoff distances (0 less than or equal to (radial distance from jet lipline to surface (inches)/axial distance from jet exit to surface trailing edge (inches)) less than or equal to 1) using only second-order polynomials to provide predictable behavior. The JSI noise model is combined with an existing jet mixing noise model to produce exhaust noise predictions. Fit quality metrics and comparisons to between the predicted and experimental data indicate that the model is suitable for many system level studies. A first-order correction to the JSI source model that accounts for the effect of nozzle aspect ratio is also explored. This correction is based on changes to the potential core length and frequency scaling associated with rectangular nozzles up to 8:1 aspect ratio. However, more work is needed to refine these findings into a formal model.

Noise↗
NASA NTRS1983

Diffusive separation of binary mixtures of CO2-H2 in a sonic-orifice expansion

The separation of binary gas mixtures of carbon dioxide and hydrogen in sonic-orifice-generated free jets is investigated over a source Reynolds number range of 100 to 3000 using the well-known electron beam fluorescence technique. The lighter species, hydrogen, is chosen as the minor species in order to examine the extent of the validity of Sherman's first-order diffusive separation theory for large separation. The diffusive separation of mixtures containing approximately 2, 5, and 20 percent hydrogen in carbon dioxide is investigated by experimentally determining the relative number densities of the two species as a function of centerline axial distance within the free jets. Sherman's diffusive separation theory is applied to the jets using axial Mach number profiles which were a combination of experimental and analytical results for gamma = 1.40 expansions. The gamma = 1.40 expansion is shown to approximate the CO2-H2 expansion quite well, and the calculated separation agrees remarkably well with the experimentally determined values.

Mccay, T. D.↗
NASA NTRS2004

A Resonant Pulse Detonation Actuator for High-Speed Boundary Layer Separation Control

A variety of different types of actuators have been previously investigated as flow control devices. Potential applications include the control of boundary layer separation in external flows, as well as jet engine inlet and diffuser flow control. The operating principles for such devices are typically based on either mechanical deflection of control surfaces (which include MEMS flap devices), mass injection (which includes combustion driven jet actuators), or through the use of synthetic jets (diaphragm devices which produce a pulsating jet with no net mass flow). This paper introduces some of the initial flow visualization work related to the development of a relatively new type of combustion-driven jet actuator that has been proposed based on a pulse detonation principle. The device is designed to utilize localized detonation of a premixed fuel (Hydrogen)-air mixture to periodically inject a jet of gas transversely into the primary flow. Initial testing with airflow successfully demonstrated resonant conditions within the range of acoustic frequencies expected for the design. Schlieren visualization of the pulsating air jet structure revealed axially symmetric vortex flow, along with the formation of shocks. Flow visualization of the first successful sustained oscillation condition is also demonstrated for one configuration of the current test section. Future testing will explore in more detail the onset of resonant combustion and the approach to conditions of sustained resonant detonation.

Beck, B. T.↗
NASA NTRS1984

Phase average measurements of the coherent structure in a Mach number 0.6 jet

Phase averaged measurements of the axial mass velocity, radial velocity, and the product of the two have been made in an artificially excited cold air jet. The radial velocity fluctuations had a lower amplitude for both the full wave and phase averaged fluctuations compared to the axial mass velocity fluctuations. The Reynolds stress tended to decay faster in amplitude than the axial mass velocity and radial velocity fluctuations for both the full wave and phase averaged components. The radial velocity fluctuations possessed higher levels of coherence than the axial mass velocity fluctuation and the Reynolds stress. When the jet was excited at the frequency of St = 0.474, a high amplitude component at that frequency dominated the entire phase averaged flowfield from X/D = 1 to 10. This fundamental frequency was accompanied by several relatively high amplitude harmonics. These harmonics were more pronounced in the radial velocity fluctuations than for the axial fluctuations or the Reynolds stress.

Emami, S.↗
NASA NTRS2008

3D RMHD Simulations of Magnetized Spine-Sheath Relativistic Jets

We have performed numerical simulations of weakly and strongly magnetized relativistic jets embedded in a weakly and strongly magnetized stationary or mildly relativistic (0.5c) sheath flow using the RAISHIN code. In the numerical simulations a jet with Lorentz factor gamma=2.5 is processed to break the initial equilibrium configuration. Results of the numerical simulations are compared to theoretical predictions from a normal mode analysis of the linearized RMHD equations describing a uniform axially magnetized cylindrical relativistic jet embedded in a uniform axially magnetized sheath flow. The prediction of increased stability of a weakly-magnetized system with mildly relativistic sheath flow to Kelvin-Helmholtz instabilities and the stabilization of a strongly magnetized system with mildly relativistic sheath flow is confirmed by the numerical simulations.

Mizuno, Yosuke↗
NASA NTRS2008

3D RMHD Simulations of Magnetized Spine-sheath Relativistic Jets

We have performed numerical simulations of weakly and strongly magnetized relativistic jets embedded in a weakly and strongly magnetized stationary or mildly relativistic'(0.5c) sheath flow using the RAISHIN code. In the numerical simulations a jet with Lorentz factor gamma=2.5 is processed to break the initial equilibrium configuration. Results of the numerical simulations are compared to theoretical predictions from a normal mode analysis of the linearized RMHD equations describing a uniform axially magnetized cylindrical relativistic jet embedded in a uniform axially magnetized sheath flow. The prediction of increased stability of a weakly-magnetized system with mildly relativistic sheath flow to Kelvin-Helmholtz instabilities and the stabilization of a strongly-magnetized system with mildly relativistic sheath flow is confirmed by the numerical simulations.

Mizuno, Yosuke↗
NASA NTRS2007

3D Relativistic MHD Simulations of Magnetized Spine-Sheath Relativistic Jets

We have performed numerical simulations of weakly and strongly magnetized relativistic jets embedded in a weakly and strongly magnetized stationary or mildly relativistic (0.5c) sheath using the RAISHIN code. In the numerical simulations a jet with Lorentz factor gamma=2.5 is precessed to break the initial equilibrium configuration. Results of the numerical simulations are compared to theoretical predictions from a normal mode-analysis of the linearized RMHD equations describing a uniform axially magnetized cylindrical relativistic jet embedded in a uniform axially magnetized moving sheath. The prediction of increased stability of a weakly-magnetized system with mildly relativistic sheath flow to Kelvin-Helmholtz instabilities and the stabilization of a strongly-magnetized system with mildly relativistic sheath flow is confirmed by the numerical simulations.

Mizuno, Yosuke↗
NASA NTRS1956

Aerodynamic Investigation of a Parabolic Body of Revolution at Mach Number of 1.92 and Some Effects of an Annular Supersonic Jet Exhausting from the Base

An aerodynamic investigation of a slender pointed parabolic body of revolution was conducted at Mach number of 1.92 with and without the effects of an annular supersonic jet exhausting from the base. Measurements with the jet inoperative were made of lift, drag, pitching moment, base pressures, and radial and axial pressures. With the jet in operation, pressure measurements were made over the rear of the body with the primary variables being angle of attack, ratio of jet velocity to stream velocity, and ratio of pressure at jet exit to stream pressure.

Love, Eugene S↗
NASA NTRS1973

Design and experimental results for a turbine with jet flap stator and jet flap

The overall performance and detailed stator performance of a negative hub reaction turbine design featuring a moderately low solidity jet flap stator and a jet flap rotor were determined. Testing was conducted over a range of turbine expansion ratios at design speed. At each expansion ratio, the stator jet flow and rotor jet flow ranged up to about 7 and 8 percent, respectively, of the turbine inlet flow. The performance of the jet flap stator/jet flap rotor turbine was compared with that of a turbine which used the same jet flap rotor and a conventional, high solidity plan stator. The effect on performance of increased axial spacing between the jet stator and rotor was also investigated.

Bettner, J. L.↗
NASA NTRS2006

3D Relativistic Magnetohydrodynamic Simulations of Magnetized Spine-Sheath Relativistic Jets

Numerical simulations of weakly magnetized and strongly magnetized relativistic jets embedded in a weakly magnetized and strongly magnetized stationary or weakly relativistic (v = c/2) sheath have been performed. A magnetic field parallel to the flow is used in these simulations performed by the new GRMHD numerical code RAISHIN used in its RMHD configuration. In the numerical simulations the Lorentz factor gamma = 2.5 jet is precessed to break the initial equilibrium configuration. In the simulations sound speeds are less than or equal to c/the square root of 3 in the weakly magnetized simulations and less than or equal to 0.56 c in the strongly magnetized simulations. The Alfven wave speed is less than or equal to 0.07 c in the weakly magnetized simulations and less than or equal to 0.56 c in the strongly magnetized simulations. The results of the numerical simulations are compared to theoretical predictions from a normal mode analysis of the linearized relativistic magnetohydrodynamic (RMHD) equations capable of describing a uniform axially magnetized cylindrical relativistic jet embedded in a uniform axially magnetized relativistically moving sheath. The theoretical dispersion relation allows investigation of effects associated with maximum possible sound speeds, Alfven wave speeds near light speed and relativistic sheath speeds. The prediction of increased stability of the weakly magnetized system resulting from c/2 sheath speeds and the stabilization of the strongly magnetized system resulting from c/2 sheath speeds is verified by the numerical simulation results.

Mizuno, Yosuke↗
NASA NTRS2004

Fluidic Chevrons for Jet Noise Reduction

Chevron mixing devices are used to reduce noise from commercial separate-flow turbofan engines. Mechanical chevron serrations at the nozzle trailing edge generate axial vorticity that enhances jet plume mixing and consequently reduces far-field noise. Fluidic chevrons generated with air injected near the nozzle trailing edge create a vorticity field similar to that of the mechanical chevrons and allow more flexibility in controlling acoustic and thrust performance than a passive mechanical design. In addition, the design of such a system has the future potential for actively controlling jet noise by pulsing or otherwise optimally distributing the injected air. Scale model jet noise experiments have been performed in the NASA Langley Low Speed Aeroacoustic Wind Tunnel to investigate the fluidic chevron concept. Acoustic data from different fluidic chevron designs are shown. Varying degrees of noise reduction are achieved depending on the injection pattern and injection flow conditions. CFD results were used to select design concepts that displayed axial vorticity growth similar to that associated with mechanical chevrons and qualitatively describe the air injection flow and the impact on acoustic performance.

Kinzie, Kevin↗
NASA NTRS1989

Opposed jet diffusion flames of nitrogen-diluted hydrogen vs air - Axial LDA and CARS surveys; fuel/air rates at extinction

An experimental study of H-air counterflow diffusion flames (CFDFs) is reported. Coaxial tubular opposed jet burners were used to form dish-shaped CFDFs centered by opposing laminar jets of H2/N2 and air in an argon bath at 1 atm. Jet velocities for extinction and flame restoration limits are shown versus input H2 concentration. LDA velocity data and CARS temperature and absolute N2, O2 density data give detailed flame structure on the air side of the stagnation point. The results show that air jet velocity is a more fundamental and appropriate measure of H2-air CFDF extinction than input H2 mass flux or fuel jet velocity. It is proposed that the observed constancy of air jet velocity for fuel mixtures containing 80 to 100 percent H2 measure a maximum, kinetically controlled rate at which the CFDF can consume oxygen in air. Fuel velocity mainly measures the input jet momentum required to center an H2/N2 versus air CFDF.

Pellett, G. L.↗