Search NASA⌕ Search

SEARCH · Search NASA

Results for “BANDWIDTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Linear and Nonlinear Analysis of Magnetic Bearing Bandwidth Due to Eddy Current Limitations

Finite element analysis was used to study the bandwidth of alloy hyperco50a and silicon iron laminated rotors and stators in magnetic bearings. A three dimensional model was made of a heteropolar bearing in which all the flux circulated in the plane of the rotor and stator laminate. A three dimensional model of a plate similar to the region of a pole near the gap was also studied with a very fine mesh. Nonlinear time transient solutions for the net flux carried by the plate were compared to steady state time harmonic solutions. Both linear and quasi-nonlinear steady state time harmonic solutions were calculated and compared. The finite element solutions for power loss and flux bandwidth were compared to those determined from classical analytical solutions to Maxwell's equations.

Kenny, Andrew↗
NASA NTRS2001

Bandwidth Criteria for Category I and II PIOs

This presentation gives information on: pitch criteria based on airplane Bandwidth; apply research, experimental, operational data; compare Smith-Geddes, Gibson, Neal-Smith criteria; bandwidth criteria for Category II PIO; control/response sensitivity and PIO; extension to roll a axis; and some recommendations.

Mitchell, David G.↗
NASA NTRS2000

Optimization of Connector Position Offset for Bandwidth Enhancement of a Multimode Optical Fiber Link

The multimode fiber bandwidth enhancement techniques to meet the Gigabit Ethernet standards for local area networks (LAN) of the Kennedy Space Center and other NASA centers have been discussed. Connector with lateral offset coupling between single mode launch fiber cable and the multimode fiber cable has been thoroughly investigated. An optimization of connector position offset for 8 km long optical fiber link at 1300 nm with 9 micrometer diameter single mode fiber (SMF) and 50 micrometer diameter multimode fiber (MMF) coupling has been obtained. The optimization is done in terms of bandwidth, eye-pattern, and bit pattern measurements. It is simpler, is a highly practical approach and is cheaper as no additional cost to manufacture the offset type of connectors is involved.

Rawat, Banmali↗
NASA NTRS2003

Bandwidth Efficient Baseband Multi-Modulator

The High Rate Baseband Multi-Modulator (HRBM) ASIC is being developed to provide High-speed Bandwidth Efficient Modulations to NASA missions. Bandwidth efficiencies from 2.0 bits/symbol/Hz to 2.75 bits/symbl/Hz are selectable from three CCSDS modulations: Gaussian Minimum Shift Keying (GMSK), Filter Offset Quadrature Phase Shift Keying (Filtered- OQSK) and 8-Phase Shift Keying Trellis Coded Modulation (8-PSK TCM). An FPGA version of the HRBM is developed first to verify the individual modulation designs and characterize timing and performance issues involved with digital baseband modulation synthesis. A Finite Input Response (FIR) filter is included to provided baseband pulse shaping to reduce out-of-band spectral emissions. This is filter is programmable and can be tailored to meet system requirements. The ASIC is targeted to provide up to 600 Mbps throughput and will provide serial as well as parallel input. This paper provides an overview of the technology development and current status.

Fong, Wai↗
NASA NTRS2005

Preferred Frequency Range, Technical Characteristics, and Interference Assessment for a Microwave Observatory of Subsurface and Subcanopy (MOSS) for 1 MHZ Bandwidth in the Frequency Range of 100-150 MHz

This document presents rationale for the frequency band selection, technical and operational characteristics of active spaceborne sensors in the Earth Exploration-Satellite Service (active), and interference assessment for a 1 MHz bandwidth sensor in the 100-150 MHz frequency range. The active spaceborne sensors expected to be operating in the frequency range of 100-150 MHz is the synthetic aperture radar (SAR) such as the MOSS. The technical characteristics, mission objectives, orbital parameters, design parameters, antenna characteristics, and preliminary interference assessment are given for MOSS. The purpose of the document is to provide rationale for the frequency band selection, technical characteristics of the active spaceborne sensor Microwave Observatory of Subsurface and Subcanopy (MOSS) that can be used to analyze the compatibility of active spaceborne sensors and other systems of 1 MHz bandwidth in the 100-150 MHz frequency band.

wideband SAR modes↗
NASA NTRS1993

Programmable noise bandwidth reduction by means of digital averaging

Predetection noise bandwidth reduction is effected by a pre-averager capable of digitally averaging the samples of an input data signal over two or more symbols, the averaging interval being defined by the input sampling rate divided by the output sampling rate. As the averaged sample is clocked to a suitable detector at a much slower rate than the input signal sampling rate the noise bandwidth at the input to the detector is reduced, the input to the detector having an improved signal to noise ratio as a result of the averaging process, and the rate at which such subsequent processing must operate is correspondingly reduced. The pre-averager forms a data filter having an output sampling rate of one sample per symbol of received data. More specifically, selected ones of a plurality of samples accumulated over two or more symbol intervals are output in response to clock signals at a rate of one sample per symbol interval. The pre-averager includes circuitry for weighting digitized signal samples using stored finite impulse response (FIR) filter coefficients. A method according to the present invention is also disclosed.

Poklemba, John J.↗
NASA NTRS2008

Unmanned Aircraft System Control and ATC Communications Bandwidth Requirements

There are significant activities taking place to establish the procedures and requirements for safe and routine operation of unmanned aircraft systems (UAS) in the National Airspace System (NAS). Among the barriers to overcome in achieving this goal is the lack of sufficient frequency spectrum necessary for the UAS control and air traffic control (ATC) communications links. This shortcoming is compounded by the fact that the UAS control communications links will likely be required to operate in protected frequency spectrum, just as ATC communications links are, because they relate to "safety and regularity of flight." To support future International Telecommunications Union (ITU) World Radio Conference (WRC) agenda items concerning new frequency allocations for UAS communications links, and to augment the Future Communications Study (FCS) Technology Evaluation Group efforts, NASA Glenn Research Center has sponsored a task to estimate the UAS control and ATC communications bandwidth requirements for safe, reliable, and routine operation of UAS in the NAS. This report describes the process and results of that task. The study focused on long-term bandwidth requirements for UAS approximately through 2030.

Henriksen, Steve↗
NASA NTRS2009

Multi-Modulator for Bandwidth-Efficient Communication

A modulator circuit board has recently been developed to be used in conjunction with a vector modulator to generate any of a large number of modulations for bandwidth-efficient radio transmission of digital data signals at rates than can exceed 100 Mb/s. The modulations include quadrature phaseshift keying (QPSK), offset quadrature phase-shift keying (OQPSK), Gaussian minimum-shift keying (GMSK), and octonary phase-shift keying (8PSK) with square-root raised-cosine pulse shaping. The figure is a greatly simplified block diagram showing the relationship between the modulator board and the rest of the transmitter. The role of the modulator board is to encode the incoming data stream and to shape the resulting pulses, which are fed as inputs to the vector modulator. The combination of encoding and pulse shaping in a given application is chosen to maximize the bandwidth efficiency. The modulator board includes gallium arsenide serial-to-parallel converters at its input end. A complementary metal oxide/semiconductor (CMOS) field-programmable gate array (FPGA) performs the coding and modulation computations and utilizes parallel processing in doing so. The results of the parallel computation are combined and converted to pulse waveforms by use of gallium arsenide parallel-to-serial converters integrated with digital-to-analog converters. Without changing the hardware, one can configure the modulator to produce any of the designed combinations of coding and modulation by loading the appropriate bit configuration file into the FPGA.

Gray, Andrew↗
NASA NTRS2009

Improved-Bandwidth Transimpedance Amplifier

The widest available operational amplifier, with the best voltage and current noise characteristics, is considered for transimpedance amplifier (TIA) applications where wide bandwidth is required to handle fast rising input signals (as for time-of-flight measurement cases). The added amplifier inside the TIA feedback loop can be configured to have slightly lower voltage gain than the bandwidth reduction factor.

Chapsky, Jacob↗
NASA NTRS2007

Single-Shot Rotational Raman Thermometry for Turbulent Flames Using a Low-Resolution Bandwidth Technique

An alternative optical thermometry technique that utilizes the low-resolution (order 10(exp 1)/cm) pure-rotational spontaneous Raman scattering of air is developed to aid single-shot multiscalar measurements in turbulent combustion studies. Temperature measurements are realized by correlating the measured envelope bandwidth of the pure-rotational manifold of the N2/O2 spectrum with a theoretical prediction of a species-weighted bandwidth. By coupling this thermometry technique with conventional vibrational Raman scattering for species determination, we demonstrate quantitative spatially resolved, single-shot measurements of the temperature and fuel/oxidizer concentrations in a high-pressure turbulent Cf4-air flame. Our technique provides not only an effective means of validating other temperature measurement methods, but also serves as a secondary thermometry technique in cases where the anti-Stokes vibrational N2 Raman signals are too low for a conventional vibrational temperature analysis.

Kojima, Jun↗
NASA NTRS2013

Large-aperture Wide-bandwidth Antireflection-coated Silicon Lenses for Millimeter Wavelengths

The increasing scale of cryogenic detector arrays for submillimeter and millimeter wavelength astrophysics has led to the need for large aperture, high index of refraction, low loss, cryogenic refracting optics. Silicon with n 3.4, low loss, and high thermal conductivity is a nearly optimal material for these purposes but requires an antireflection (AR) coating with broad bandwidth, low loss, low reflectance, and a matched coefficient of thermal expansion. We present an AR coating for curved silicon optics comprised of subwavelength features cut into the lens surface with a custom three-axis silicon dicing saw. These features constitute a metamaterial that behaves as a simple dielectric coating.We have fabricated silicon lenses as large as 33.4 cm in diameter with micromachined layers optimized for use between 125 and 165 GHz. Our design reduces average reflections to a few tenths of a percent for angles of incidence up to 30deg with low cross polarization.We describe the design, tolerance, manufacture, and measurements of these coatings and present measurements of the optical properties of silicon at millimeter wavelengths at cryogenic and room temperatures. This coating and lens fabrication approach is applicable from centimeter to submillimeter wavelengths and can be used to fabricate coatings with greater than octave bandwidth.

thermal expansion↗
NASA NTRS2013

Large-Aperture Wide-Bandwidth Anti-Reflection-Coated Silicon Lenses for Millimeter Wavelengths

The increasing scale of cryogenic detector arrays for sub-millimeter and millimeter wavelength astrophysics has led to the need for large aperture, high index of refraction, low loss, cryogenic refracting optics. Silicon with n = 3.4, low loss, and relatively high thermal conductivity is a nearly optimal material for these purposes, but requires an antireflection (AR) coating with broad bandwidth, low loss, low reflectance, and a matched coffecient of thermal expansion. We present an AR coating for curved silicon optics comprised of subwavelength features cut into the lens surface with a custom three axis silicon dicing saw. These features constitute a metamaterial that behaves as a simple dielectric coating. We have fabricated and coated silicon lenses as large as 33.4 cm in diameter with coatings optimized for use between 125-165 GHz. Our design reduces average reflections to a few tenths of a percent for angles of incidence up to 30 deg. with low cross-polarization. We describe the design, tolerance, manufacture, and measurements of these coatings and present measurements of the optical properties of silicon at millimeter wavelengths at cryogenic and room temperatures. This coating and lens fabrication approach is applicable from centimeter to sub-millimeter wavelengths and can be used to fabricate coatings with greater than octave bandwidth.

millimeter wavelength astrophysics↗
NASA NTRS2011

Wideband Spectroscopy: The Design and Implementation of a 3 GHz Bandwidth, 8192 Channel, Polyphase Digital Spectrometer

A family of state-of-the-art digital Fourier transform spectrometers has been developed, with a combination of high bandwidth and fine resolution unavailable elsewhere. Analog signals consisting of radiation emitted by constituents in planetary atmospheres or galactic sources are downconverted and subsequently digitized by a pair of interleaved Analog-to-Digital Converters, (ADC). This 6 Gsps (giga-sample per second) digital representation of the analog signal is then processed through an FPGA-based streaming Fast Fourier Transform (FFT), the key development described below. Digital spectrometers have many advantages over previously used analog spectrometers, especially in terms of accuracy and resolution, both of which are particularly important for the type of scientific questions to be addressed with next-generation radiometers. the implementation, results and underlying math for this spectrometer, as well as, potential for future extension to even higher bandwidth, resolution and channel orthogonality, needed to support proposed future advanced atmospheric science and radioastronomy, are discussed.

field programmable gate array↗
NASA NTRS2013

Coarse-Grain Bandwidth Estimation Techniques for Large-Scale Space Network

In this paper, we describe a top-down analysis and simulation approach to size the bandwidths of a store-andforward network for a given network topology, a mission traffic scenario, and a set of data types with different latency requirements. We use these techniques to estimate the wide area network (WAN) bandwidths of the ground links for different architecture options of the proposed Integrated Space Communication and Navigation (SCaN) Network.

Cheung, Kar-Ming↗
NASA NTRS2018

Use of Multi-Spectral High Repetition Rate LED Systems for High Bandwidth Underwater Optical Communications, and Communications to Surface and Aerial Systems

A variety of both existing and developing sensors would benefit from near real time communication of high bandwidth data. To cite just one example, sensors that could more accurately report real-time positions of marine mammals would be useful in reducing whale-ship collisions. Similar considerations are relevant for maritime port and harbor security, including detection and alerts for divers or autonomous underwater vehicles (AUVs) that could pose a risk to ships. Especially in ports and harbors, field experiments have confirmed that acoustic communication in these cluttered and noisy shallow water environments, compounded with vertical reflecting surfaces formed by piers and pilings, can limit the reliability and utility of underwater acoustic communications. Moreover, many sensors have greater bandwidth requirements than acoustic communications are able to provide. We here discuss the development of high repetition rate multispectral LED optical systems initially developed for imaging, but also capable of simultaneous data transmission at rates of approximately100 kilobits per second. Results are discussed for the multispectral images from coral reefs in Guam, and data transmission experiments from underwater to surface vessels. Subsequent field efforts will extend data transmission from AUVs to unmanned aircraft systems (UAS).

Underwater↗
NASA NTRS2018

An Overview of High Bandwidth Liquid Fuel Flow Modulators Developed for Active Combustion Control Research

This paper presents a description of the general construction of three high bandwidth liquid fuel modulators along with data corresponding to their respective modulation performance. These devices are a critical element of the National Aeronautics and Space Administration Glenn Research Center's (NASA GRC) Active Combustion Control (ACC) task. These devices are not commercially-off-the-shelf available, primarily due to a one kHz bandwidth requirement. Given their special nature, NASA GRC developed specifications for the modulation devices and then, through Small Business Innovative Research (SBIR) contracts, had vendors with expertise in valve design manufacture them. The modulators described in this paper are the Active Signal Modulator (ASM), the Jansen's Aircraft System Controls (JASC) modulator, and the WASK Engineering (WASK) modulator. These modulators utilize magnetostrictive, electric motor, or piezoelectric actuation, respectively. The specifications for these devices evolved over time to meet the needs of changing objectives in the ACC research task. This is primarily true with respect to flow number as their designs accommodate a range from one to eight (lbm./hr-psi0.5). These designs also exhibit relatively small volume, weight, and power consumption with an ability to modulate approximately +/- 30% from the mean on a pressure basis. The modulators have been characterized and have undergone laboratory performance tests by the vendors. Their data indicated suitability for continued use in ACC research testing.

Saus, Joseph R.↗
NASA NTRS2021

Wide Bandwidth Radiometer Sensitivity for Remote Sensing of Ocean Salinity

Modern microwave radiometers have demonstrated the feasibility of monitoring surface salinity from space and also the need for better accuracy in cold water. Accuracy could be improved by adding measurements at lower frequencies (lower than the measurement at 1.4 GHz currently used) and closer to the peak in sensitivity of brightness temperature to changes in salinity. Proposals to accomplish this have focused on wide bandwidth receivers which include at the low end frequencies close to the peak in sensitivity. This strategy involves trade-offs, some obvious such as radio frequency interference (RFI) when operating outside the protected band at 1.4 GHz and the loss of spatial resolution at lower frequencies. Others stemming from the interdependence of the retrieval of salinity on water temperature and surface roughness are more subtle. The objective of this manuscript is to examine this interdependence and its implications to future wide bandwidth instruments for remote sensing of salinity from space.

microwave radiometry↗