Search NASA⌕ Search

SEARCH · Search NASA

Results for “Boeing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Pilots noise exposure during a Boeing 747-400 round trip: Ambient noise and acoustic-head recording and analysis of data

Pilot noise exposure is examined during the round trip flight of a Boeing 747-400 aircraft. Although the sound power origin is the aircraft, this paper examines the effects of this noise on the human occupants within the airplane. Data is acquired and analyzed to determine the noise exposure of pilots on long flights, in this case, a flight of 12 hours and 20 minutes. All results are presented in viewgraph format.

Hoffman, Knut↗
NASA NTRS1992

Pilot noise exposure during a Boeing 747-400 round trip: Judgement of noise and analysis in respect to hearing impairment of pilots

Noise level measurements are made on Boeing 747 aircraft to determine the potential hazards to airline pilots. Measuring results have shown that most pilots work under conditions that where noise constitutes a health hazard. Long and short term effects of noise exposure in pilots is examined as well as the legal ramifications of this potential hazard.

Hans Juergen Hooman↗
NASA NTRS1992

Design and analysis of reengine Boeing 727-100 center inlet S duct by a reduced Navier-Stokes code

This paper describes the application of a three-dimensional reduced Navier-Stokes code to perform design and analysis of the reengine Boeing 727-100 center engine inlet S duct. This computer code is shown to be cost effective, accurate and easy to use to design the optimal S duct geometries, predict its aerodynamic performance and provide the detailed flowfield information.

Huang, Pao S.↗
NASA NTRS1992

Design and analysis of vortex generators on reengined Boeing 727-100QF center inlet S-duct by a reduced Navier-Stokes code

This paper describes the application of a three dimensional reduced Navier-Stokes code to perform design and analysis of vortex generators on a reengined Boeing 727-100QF center engine inlet S duct. This computer code with vortex generators modeling is shown to be cost-effective, accurate and easy to use to design the optimal vortex generators installed on a S-duct, predict its aerodynamic performance and provide the detailed flow field information.

Huang, Pao S.↗
NASA NTRS1984

Boeing Modeling Programs

The Boeing wind tunnel modeling programs are presented. Shown are viewgraphs of management hierarchy, wind tunnel characteristics, wind tunnel photographs, and geometric drawings.

Doerzbacher, Robert P.↗
NASA NTRS1952

Effect on Longitudinal Stability and Control Characteristics of a Boeing B-29 Airplane of Variations in Stick-Force and Control-Rate Characteristics Obtained Through Use of a Booster in the Elevator-Control System

A longitudinal stability and control characteristics of a Boeing B-29 airplane have been measured with a booster incorporated in the elevator-control system. Tests were made to determine the effects on the handling qualities of the test airplane of variations in the pilot's control-force gradients as well as the effects of variations in the maximum rate of control motion supplied by the booster. The results of the control-rate investigation indicate that large airplanes may have satisfactory handling qualities with the booster adjusted to give much lower rates of control motion than those normally used by pilots.

Mathews, Charles W↗
NASA NTRS1995

Collection Efficiency and Ice Accretion Calculations for a Sphere, a Swept MS(1)-317 Wing, a Swept NACA-0012 Wing Tip, an Axisymmetric Inlet, and a Boeing 737-300

Collection efficiency and ice accretion calculations have been made for a sphere, a swept MS(1)-317 wing, a swept NACA-0012 wing tip, an axisymmetric inlet, and a Boeing 737-300 inlet using the NPARC flow solver and the NASA Lewis LEWICE3D grid based ice accretion code. Euler flow solutions for the geometries were generated using the NPARC flow solver. The LEWICE3D grid based ice accretion program was used to calculate the impingement efficiencies and ice shapes. Ice shapes specifying rime and mixed icing conditions were generated for a 30 minute hold condition. All calculations were performed on an SGI Model Power Challenge Computer. The results have been compared to experimental flow and impingement data. In general, the calculated flow and collection efficiencies compared well with experiment, and the ice shapes looked reasonable and appeared representative of the rime and mixed icing conditions for which they were calculated.

Bidwell, Colin S.↗
NASA NTRS1997

Collection Efficiency and Ice Accretion Calculations for a Boeing 737-300 Inlet

Collection efficiency and ice accretion calculations have been made for a Boeing 737-300 inlet using a three-dimensional panel code, an adaptive grid code, the NASA Lewis LEWICE3D grid based ice accretion code. Flow solutions for the inlet were generated using the VSAERO panel code. Grids used in the ice accretion calculations were generated using the newly developed adaptive grid code ICEGRID3D. The LEWICE3D grid based ice accretion program was used to calculate impingement efficiency and ice shapes. Ice shapes typifying rime and mixed icing conditions were generated for a 30 minute hold condition. All calculations were performed on an SGI Power Challenge computer. The results have been compared to experimental flow and impingement data. In general, the calculated flow and collection efficiencies compared well with experiment, and the ice shapes looked reasonable and appeared representative of the rime and mixed icing conditions for which they were calculated.

Bidwell, Colin S.↗
NASA NTRS1999

Langley's Computational Efforts in Sonic-Boom Softening of the Boeing HSCT

NASA Langley's computational efforts in the sonic-boom softening of the Boeing high-speed civil transport are discussed in this paper. In these efforts, an optimization process using a higher order Euler method for analysis was employed to reduce the sonic boom of a baseline configuration through fuselage camber and wing dihedral modifications. Fuselage modifications did not provide any improvements, but the dihedral modifications were shown to be an important tool for the softening process. The study also included aerodynamic and sonic-boom analyses of the baseline and some of the proposed "softened" configurations. Comparisons of two Euler methodologies and two propagation programs for sonic-boom predictions are also discussed in the present paper.

Fouladi, Kamran↗
NASA NTRS1999

Simulated Inlet Unstart and Nacelle/Diverter Effects for the Boeing Reference H Configuration

The Boeing Reference H configuration was tested in the NASA Ames 9x7 Supersonic Wind Tunnel. A simulated unstarted inlet was evaluated as well as the aerodynamic performance of the configuration with and without nacelle and diverter components. These experimental results were compared with computational results from the unstructured grid Euler flow solver AIRPLANE. The comparisons between computational and experimental results were good, and demonstrated that the Euler code is capable of efficiently and accurately predicting the changes in the aerodynamic coefficients associated with inlet unstart and the effects of the nacelle and diverter components.

Cliff, Susan E.↗
NASA NTRS2000

Pilot Comments From the Boeing High Speed Research Aircraft, Cycle 3, Simulation Study of the Effects of Aeroservoelasticity (LaRC.3)

This is a compilation of pilot comments from the Boeing High Speed Research Aircraft, Cycle 3, simulation study (LaRC.3) of the effects of aeroservoelasticity, conducted from October to December 1997 at NASA Langley Research Center. This simulation study was conducted using the Visual Motion Simulator. The comments are from direct tape transcriptions and have been edited for spelling only. These comments were made on tape following the completion of each flight card, immediately after the pilot was satisfied with his practice and data recording runs. Six pilots were used in the evaluation and they are identified as pilots A through F.

Bailey, Melvin L.↗
NASA NTRS1994

Navier-Stokes Flowfield Simulation of Boeing 747-200 as Platform for SOFIA

Steady and unsteady viscous, three-dimensional flowfields are calculated using a thin layer approximation of Navier-Stokes equations in conjunction with Chimera overset grids. The finite-difference numerical scheme uses structured grids and a pentadiagonal flow solver called "OVERFLOW". The configuration of Boeing 747-200 has been chosen as one of configurations to be used as a platform for the SOFIA (Stratospheric Observatory For Infrared Astronomy). Initially, the steady flowfield of the full aircraft is calculated for the clean configuration (without a cavity to house telescope). This solution is then used to start the unsteady flowfield of a configuration containing cavity housing the observation telescope and its peripheral units. Analysis of unsteady flowfield in the cavity and its influence on the tail empennage, as well as the noise due to turbulence and optical quality of the flow are the main focus of this study. For the configuration considered here, the telescope housing cavity is located slightly downstream of the portwing. The entire flow-field is carefully constructed using 45 overset grids and consists of nearly 4 million grid points. All the computations axe done at one freestream flow condition of M(sub infinity) = 0.85, alpha = 2.5deg, and a Reynolds of Re = 1.85x10deg

Srinivasan, G.R.↗
NASA NTRS1947

Force Tests of the Boeing XB-47 Full-Scale Empennage in the Ames 40- by 80-Foot Wind Tunnel

A wind-tunnel investigation of the Boeing XB-47 full-scale empennage was conducted to provide, prior to flight tests, data required on the effectiveness of the elevator and rudder. The XB-47 airplane is a jet-propelled medium bomber having wing and tail surfaces swept back 35 degrees. The investigation included tests of the effectiveness of the elevator with normal straight sides, with a buldged trailing edge, and with a modified hinge-line gap and tests of the effectiveness of the rudder with a normal straight-sided tab and with a bulged tab.

Hunton, Lynn W.↗
NASA NTRS2003

Measured Radiation Patterns of the Boeing 91-Element ICAPA Antenna With Comparison to Calculations

This report presents measured antenna patterns of the Boeing 91-Element Integrated Circuit Active Phased Array (ICAPA) Antenna at 19.85 GHz. These patterns were taken in support of various communication experiments that were performed using the antenna as a testbed. The goal here is to establish a foundation of the performance of the antenna for the experiments. An independent variable used in the communication experiments was the scan angle of the antenna. Therefore, the results presented here are patterns as a function of scan angle, at the stated frequency. Only a limited number of scan angles could be measured. Therefore, a computer program was written to simulate the pattern performance of the antenna at any scan angle. This program can be used to facilitate further study of the antenna. The computed patterns from this program are compared to the measured patterns as a means of validating the model.

Lambert, Kevin M.↗
NASA NTRS2004

Crash Simulation of a Boeing 737 Fuselage Section Vertical Drop Test

A 30-ft/s vertical drop test of a fuselage section of a Boeing 737 aircraft was conducted in October of 1999 at the FAA Technical Center in Atlantic City, NJ. This test was performed to evaluate the structural integrity of a conformable auxiliary fuel tank mounted beneath the floor and to determine its effect on the impact response of the airframe structure and the occupants. The test data were used to compare with a finite element simulation of the fuselage structure and to gain a better understanding of the impact physics through analytical/experimental correlation. To perform this simulation, a full-scale 3-dimensional finite element model of the fuselage section was developed using the explicit, nonlinear transient-dynamic finite element code, MSC.Dytran. The emphasis of the simulation was to predict the structural deformation and floor-level acceleration responses obtained from the drop test of the B737 fuselage section with the auxiliary fuel tank.

Fasanella, Edwin L.↗
NASA NTRS1952

Structural Vulnerability of the Boeing B-29 Aircraft Wing to Damage by Warhead Fragments

An elementary type of analysis has been used to determine the amount of wing tip that must be severed to produce irrevocable loss of control of a B-29 airplane. The remaining inboard structure of the Boeing B-29 wing has then been analyzed and curves are presented for the estimated reduction in structural strength due to four general types of damage produced by rod-type warhead fragments. The curves indicate the extent of structural damage required to produce a kill of the aircraft within 10 seconds.

Kordes, Eldon E.↗
NASA NTRS1950

Ditching Investigation of a 1/24-Scale Model of the Boeing B-47 Airplane

An investigation of a 1/24-scale dynamically similar model of the Boeing B-47 airplane was made to determine the ditching characteristics and proper ditching technique for the airplane. Various conditions of damage, landing attitude, flap setting, and speed were investigated. The behavior of the model was determined from visual observations, motion-picture records, and time-history deceleration records. The results of the investigation are presented in table form, photographs, and curves. The airplane should be ditched at the lowest speed and highest attitude consistent with adequate control; the flaps should be full down. The airplane will probably make a deep but fairly smooth run. The fuselage bottom will be damaged and partially filled with water; consequently, crew members should be assigned ditching stations near an exit in the upper or forward part of the fuselage. The nacelles may be expected to be torn away from the wing. In calm water the maximum decelerations will be about 3g and the landing run will be about 6 fuselage lengths.

Fisher, Lloyd J.↗
NASA NTRS1955

Ditching Investigation of a 1/20-Scale Model of the Boeing Stratocruiser Airplane (C-97)

An investigation of a 1/20-scale dynamically similar model of the Boeing Stratocruiser airplane (C-97) was made to determine the ditching characteristics and proper technique for ditching the airplane. Scale-strength bottoms were used to determine probable damage to the fuselage and the effect of damage on behavior. The behavior of the model was determined from visual observations, motion-picture records, and time-history deceleration records. Data are presented in a table, photographs, and curves. It was concluded that the airplane should be ditched at a medium nose-high landing attitude (near 6 deg) with landing flaps full down. The airplane will probably make a smooth run of medium depth with light spray and may even trim up slightly in the water. The fuselage will probably be damaged and the lower compartment filled with water. In calm water, the maximum longitudinal deceleration will be about 4g and the landing run will be about four fuselage lengths.

Fisher, Lloyd J.↗