SEARCH · Search NASA

Results for “Brittle solid”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Experimental evaluation of 150-millimeter bore ball bearing to 3 million DN using either solid or drilled balls

Seven 150-mm bore ball bearings were run under 8900 Newton (2000 lb) thrust load at speeds from 6670 to 20,000 rpm (1 to 3 million DN). Four of the bearings had conventional solid balls and three bearing had drilled (cylindrically hollow) balls with 50 percent mass reduction. The bearings were under-race cooled and slot-lubricated with Type 2 ester oil at flow rates from 4.35 to 5.80 liters per minute (1.15 to 1.57 gal min). Friction torque and temperatures were measured on all bearings. No significant difference in torque was noted, between the solid and drilled ball bearings. One bearing of each type was rerun at 17,800 Newtons (4000 lb) thrust load. The solid ball bearings performed satisfactorily at 3 million DN. However, at about 2 million DN the drilled ball bearing experienced a broken ball and cracks appeared in two other balls as the result of flexure fatigue. Metallurgical examination of the cracked balls indicated a brittle structure in the bore of the drilled balls.

Scibbe, H. W.↗

DOE OSTI2024

Diffusion bonding of tungsten-vanadium-zirconium using vacuum hot pressing for the development of a low decay heat cladding solution for tungsten spallation targets

Tantalum has been used as cladding material for water-cooled solid tungsten targets at many leading spallation neutron production facilities thanks to its high neutron yield, manageable radiation damage behavior, and excellent corrosion/erosion resistance in radiation environments. However, from a safety hazard perspective, thermal neutron capture of tantalum in spallation environments causes a high specific decay heat in the target volume, which often becomes a limiting factor in increasing the beam power on the target. In this paper, we studied vacuum hot pressing (VHP) parameters to diffusion bond zirconium to tungsten to explore the feasibility of using zirconium alloys as an alternative cladding material to tantalum. Zirconium alloys have long been used as cladding material for early generation solid spallation targets, and nuclear fuel rods. In spallation environments zirconium has significantly lower decay heat with shorter decay time compared to tantalum. The hot isostatic pressing (HIP) of zirconium and tungsten is known to produce limited bonding quality due to the formation of the brittle ZrW2 intermetallic layer. To overcome this problem, placing a vanadium interlayer between tungsten and zirconium has been proposed by exploring parameter space in binary alloy phase diagrams. Under the VHP conditions, 860 ◦C at 70 MPa for 4 hours, Zr-V and V-W showed good diffusion bonding, which demonstrates the feasibility of a single step HIP process to make the zirconium alloy clad tungsten spallation volumes.

Lee, Yong Joong↗

DOE OSTI2020

Tensile properties of powder-metallurgical-processed tungsten alloys after neutron irradiation near recrystallization temperatures

The tensile properties of powder-metallurgical-processed Pure W, K-doped W, W-3%Re, and K-doped W-3%Re were examined after neutron irradiation up to 0.7 dpa at 910–1020 °C with a thermal neutron shield in the High Flux Isotope Reactor (HFIR). After irradiation, recrystallized Pure W (R) exhibited a brittle fracture mode, while recrystallized K-doped W-3%Re (R) exhibited a ductile fracture mode at 500 °C. K-doped W-3%Re (R) has fine grains, and hence, contains a considerable number of grain boundaries that act as sinks for irradiation defects. Solid solute Re in the W matrix could improve not only the mechanical properties of W, but also its resistance to neutron irradiation. At 500 °C, the ductility of K-doped W-3%Re after irradiation was significantly higher than that of Pure W. The irradiation at ~1000 °C did not induce hardening of stress-relieved (SR) W materials, but SR W materials tended to exhibit a decrease in the ultimate tensile strength (UTS) and an increase in total elongation (TE). Here, the softening due to the recovery and recrystallization of SR W materials and the hardening due to the formation of irradiation defect clusters were balanced during irradiation at ~1000 °C, and ductility was exhibited without an increase in strength.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Mineral-Ground Micro-Fibrillated Cellulose Reinforcement for Polymer Compounds

Additive Manufacturing (AM) is quickly becoming a mainstream, energy efficient manufacturing technique for complex and custom components. ORNL has taken polymer AM into the next level with Big Area Additive Manufacturing (BAAM). However, we need to develop the strength of AM materials (specifically polymers) to satisfy the mechanical requirements of structural parts. Also, it is crucial that the developed process can easily be scaled up to have a significant impact in the manufacturing industry of US. Furthermore, renewable, bio-derived AM materials are desirable from a sustainability perspective. In the first phase of this project the mechanical properties of polymer AM components were significantly improved developing a micro fibrillated cellulose (MFC)-reinforced composite material system that is derived from biomass and compatible with BAAM. Unfortunately, the improvements were observed only with freeze-dried MFCs, and freeze-drying is a very slow process and is not industrially scalable. Furthermore, MFCs were not available in large quantities at low cost. However, FiberLean has reached 12,000 tons/year capacity (60,000 tons/year including the minerals). FiberLean offers MFCs at a scale and order of magnitude lower price than current market participants. With their recently developed novel (patent pending) drying process FiberLean can achieve over 50% solid content commercially. In the 2nd phase of the project, the original objective was to investigate this new novel drying process along with compounding with different formulations to optimize and adapt to large scale additive manufacturing. However, the compounded materials prepared via this approach were very brittle and demonstrated poor mechanical performance. Therefore, the project was focused more on a scalable chemical surface modification of MFCs to enable their drying via conventional oven process with minimal agglomeration and better dispersion in PLA polymer matrix. Fiberlean and ORNL have worked together in this project to develop mineral-ground microfibrillated cellulose (MFC) - reinforced additive manufacturing feedstock materials with significantly improved mechanical properties. Properly surface modified and dried Fiberlean cellulose microfibrils led to tensile strength increases up to ~40% and elastic modulus increases up to 70% with the addition of 30% MFC into PLA matrix. The work has led to a high impact journal article and a provisional patent. Opportunities for a follow up work to demonstrate the technology in large scale and application of it to AM applications are currently being searched.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Computational Design of Interlayers for Thermally Stable Compositionally Graded Coatings on Nickel Alloys

To extend the service life of Ni-based superalloys, refractory metal coatings are often used. However, direct bonding between metals with dissimilar crystal structure promotes brittle intermetallic phase formation. This work presents a computational thermodynamic framework for high throughput design of functionally graded interlayers to suppress deleterious phases that may form at the interlayer. The Thermo-Calc software package was used to screen candidate metallic interlayer elements based on stability of solid-solution phases. Vanadium was identified as a promising interlayer due to its consistent suppression of intermetallic phases. Temperature-dependent phase diagram mapping between 600 and 1000 °C guided selection of a compositional pathway that significantly reduced intermetallic formation compared to directly joining the Ni-based and Nb refractory alloys. Time–temperature–transformation analysis was performed to assess whether equilibrium-predicted phases are kinetically accessible along regions of the graded path where non-solid-solution phases are not fully suppressed. The methodology was further applied to additional Ni-based alloy and coating systems, illustrating its transferability as an approach for rapid computational design of graded interlayers in dissimilar high-temperature materials.

36 MATERIALS SCIENCE↗

NASA NTRS1991

A major advance in powder metallurgy

Ultramet has developed a process which promises to significantly increase the mechanical properties of powder metallurgy (PM) parts. Current PM technology uses mixed powders of various constituents prior to compaction. The homogeneity and flaw distribution in PM parts depends on the uniformity of mixing and the maintenance of uniformity during compaction. Conventional PM fabrication processes typically result in non-uniform distribution of the matrix, flaw generation due to particle-particle contact when one of the constituents is a brittle material, and grain growth caused by high temperature, long duration compaction processes. Additionally, a significant amount of matrix material is usually necessary to fill voids and create 100 percent dense parts. In Ultramet's process, each individual particle is coated with the matrix material, and compaction is performed by solid state processing. In this program, Ultramet coated 12-micron tungsten particles with approximately 5 wt percent nickel/iron. After compaction, flexure strengths were measured 50 percent higher than those achieved in conventional liquid phase sintered parts (10 wt percent Ni/Fe). Further results and other material combinations are discussed.

Williams, Brian E.↗

NASA NTRS1972

Effect of metallurgical structure and properties on adhesion and friction behavior of cobalt alloys

The metallurgical structure and some of the mechanical properties of two cobalt alloys, cobalt-50% iron and cobalt-25% molybdenum-10% chromium, were determined under various heat treated conditions. The mechanical properties of the bcc disordered Co-50Fe alloy, which was found to be very brittle, indicated an exceedingly low fracture strength, low hardness, and very weak grain boundary strength. Ordering by suitable heat treatment only produced a more brittle material with a lower fracture strength and a slightly higher hardness value. Work hardening was found to produce a finer grain structure and a greater grain boundary strength. Tensile properties were examined. It was found that the Co-25Mo-10Cr alloy was difficult to place in the alpha Co solid solution condition, which limited the ability to use precipitation as a hardening reaction. Over two hundred adhesion cycles from zero contact load, to maximum load, to fracture were conducted between couples for each of the above alloys in an ultrahigh vacuum system which would permit the sample surfaces to be cleaned of all contaminant layers. In the Co-50Fe case, the calculated fracture stress from the adhesion tests showed values in the range of 80 to 150 k.s.i., which is about ten times greater than the values from tension tests.

Keller, D. V., Jr.↗

DOE OSTI2023

One dislocation at a time

The direct observation of enhanced dislocation mobility in iron by in situ electron microscopy offers key insights and adds to the ongoing debate on the mechanisms of hydrogen embrittlement. The tiniest atom in nature, hydrogen, is pervasive and sneaky. When hydrogen atoms, either from gas or liquid sources, come into contact with a metal, they rush into the solid and squeeze through the narrow spaces between the host atoms. Being chemically active, atomic hydrogen can potentially bind to either host or impurity atoms, forming hydrides and thus changing a material’s properties. Metals, which are well known and widely used in industry for their strength and ductility, can become dangerously brittle when exposed to hydrogen. Furthermore, this phenomenon is known as hydrogen embrittlement and can lead to catastrophic failure of a load-bearing part. For example, the hydrogen produced when water molecules break apart in coolants in a nuclear reactor can cause sudden failure of the pressure vessel. In another example, although blending hydrogen in natural-gas pipelines provides a promising pathway to transition into the hydrogen economy, it could lower the fatigue resistance of the pipeline steel, making it more susceptible to crack growth due to cyclic loading induced by pressure fluctuations in the pipeline. Remarkably, perhaps as a result of a multitude of recognized failure mechanisms in which hydrogen can potentially participate, it still remains unknown exactly why hydrogen makes a metal brittle. Now, writing in Nature Materials, Longchao Huang and colleagues present unambiguous experimental observations of hydrogen-enhanced dislocation mobility in iron, offering key insights into the hydrogen embrittlement mechanisms.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Grain-boundary fracture mechanisms in Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolytes: When phase transformation acts as a temperature-dependent toughening mechanism

Garnet-type, solid electrolytes, such as Li 7 La 3 Zr 2 O 12 (LLZO), are a promising alternative to liquid electrolytes for lithium-metal batteries. However, such solid-electrolyte materials frequently exhibit undesirable lithium (Li) metal plating and fracture along grain boundaries. In this work, we employ atomistic simulations to investigate the mechanisms and key fracture properties associated with intergranular fracture along one such boundary. Our results show that, in the case of a Σ5 (310) grain boundary, this boundary exhibits brittle fracture behavior, i.e. the absence of dislocation activity ahead of the propagating crack tip, accompanied with a decrease in work of separation, peak stress, and maximum stress intensity factor as the temperature increases from 300 K to 1500 K. As the crack propagates, we predict two temperature-dependent Li clustering regimes. For temperatures at or below 900 K, Li tends to cluster in the bulk region away from the crack plane driven by a void-coalescence mechanism concomitant a simultaneous cubic-to-tetragonal phase transition. The tetragonalization of LLZO in this temperature regime acts as an emerging toughening mechanism. At higher temperatures, this phase transition mechanism is suppressed leading to a more uniform distribution of Li throughout the grain-boundary system and lower fracture properties as compared to lower temperatures.

36 MATERIALS SCIENCE↗

NASA NTRS2008

Evaluating Dimethyldiethoxysilane for use in Polyurethane Crosslinked Silica Aerogels

Silica aerogels are highly porous materials which exhibit exceptionally low density and thermal conductivity. Their "pearl necklace" nanostructure, however, is inherently weak; most silica aerogels are brittle and fragile. The strength of aerogels can be improved by employing an additional crosslinking step using isocyanates. In this work, dimethyldiethoxysilane (DMDES) is evaluated for use in the silane backbone of polyurethane crosslinked aerogels. Approximately half of the resulting aerogels exhibited a core/shell morphology of hard crosslinked aerogel surrounding a softer, uncrosslinked center. Solid state NMR and scanning electron microscopy results indicate the DMDES incorporated itself as a conformal coating around the outside of the secondary silica particles, in much the same manner as isocyanate crosslinking. Response surface curves were generated from compression data, indicating levels of reinforcement comparable to that in previous literature, despite the core/shell morphology.

Randall, Jason P.↗

DOE OSTI2025

A cost-effective all-in-one halide material for all-solid-state batteries

All-solid-state batteries require advanced cathode designs to realize their potential for high energy density and economic viability. Integrated all-in-one cathodes, which eliminate inactive conductive additives and heterogeneous interfaces, hold promise for substantial energy and stability gains but are hindered by materials lacking sufficient Li + /e − conductivity, mechanical robustness and structural stability. Here, in this work, we present Li 1.3 Fe 1.2 Cl 4 , a cost-effective halide material that overcomes these challenges. Leveraging reversible Fe 2+ /Fe 3+ redox and rapid Li + /e − transport within its framework, Li 1.3 Fe 1.2 Cl 4 achieves an electrode energy density of 529.3 Wh kg −1 versus Li + /Li. Critically, Li 1.3 Fe 1.2 Cl 4 shows unique dynamic properties during cycling, including reversible local Fe migration and a brittle-to-ductile transition that confers self-healing behaviour. This enables exceptional cycling stability, maintaining 90% capacity retention for 3,000 cycles at a rate of 5 C. Integration of Li 1.3 Fe 1.2 Cl 4 with a nickel-rich layered oxide further increases the energy density to 725.6 Wh kg −1 . By harnessing the advantageous dynamic mechanical and diffusion properties of all-in-one halides, this work establishes all-in-one halides as an avenue for energy-dense, durable cathodes in next-generation all-solid-state batteries.

25 ENERGY STORAGE↗

NASA NTRS2010

Tectonics of the Outer Planet Satellites

Tectonic features on the satellites of the outer planets range from the familiar, such as clearly recognizable graben on many satellites, to the bizarre, such as the ubiquitous double ridges on Europa, the twisting sets of ridges on Triton, or the isolated giant mountains rising from Io's surface. All of the large and middle-sized outer planet satellites except Io are dominated by water ice near their surfaces. Though ice is a brittle material at the cold temperatures found in the outer solar system, the amount of energy it takes to bring it close to its melting point is lower than for a rocky body. Therefore, some unique features of icy satellite tectonics may be influenced by a near-surface ductile layer beneath the brittle surface material, and several of the icy satellites may possess subsurface oceans. Sources of stress to drive tectonism are commonly dominated by the tides that deform these satellites as they orbit their primary giant planets. On several satellites, the observed tectonic features may be the result of changes in their tidal figures, or motions of their solid surfaces with respect to their tidal figures. Other driving mechanisms for tectonics include volume changes due to ice or water phase changes in the interior, thermoelastic stress, deformation of the surface above rising diapirs of warm ice, and motion of subsurface material toward large impact basins as they fill in and relax. Most satellites exhibit evidence for extensional deformation, and some exhibit strike-slip faulting, whereas contractional tectonism appears to be rare. Io s surface is unique, exhibiting huge isolated mountains that may be blocks of crust tilting and foundering into the rapidly emptying interior as the surface is constantly buried by deposits from hyperactive volcanoes. Of the satellites, diminutive Enceladus is spectacularly active; its south polar terrain is a site of young tectonism, copious heat flow, and tall plumes venting into space. Europa's surface is pervasively tectonized, covered with a diverse array of exotic and incompletely understood tectonic features. The paucity of impact craters on Europa suggests that its tectonic activity is ongoing. Geysers on Triton show that some degree of current activity, while tectonic features that cross sparsely cratered terrain indicate that it may also be tectonically active. Ganymede and Miranda both exhibit ancient terrains that have been pulled apart by normal faulting. On Ganymede these faults form a global network, while they are confined to regional provinces on Miranda. Ariel, Dione, Tethys, Rhea, and Titania all have systems of normal faults cutting across their surfaces, though the rifting is less pronounced than it is on Ganymede and Miranda. Iapetus exhibits a giant equatorial ridge that has defied simple explanation. The rest of the large and middle-sized satellites show very little evidence for tectonic features on their surfaces, though the exploration of Titan's surface has just begun.

McKinnon, W. B.↗

DOE OSTI2024

Real-Time Observation of Nanoscale Kink Band Mediated Plasticity in Ion-Irradiated Graphite: An In Situ TEM Study

Graphite IG-110 is a synthetic polycrystalline material used as a neutron moderator in reactors. Graphite is inherently brittle and is known to exhibit a further increase in brittleness due to radiation damage at room temperature. To understand the irradiation effects on pre-existing defects and their overall influence on external load, micropillar compression tests were performed using in situ nanoindentation in the Transmission Electron Microscopy (TEM) for both pristine and ion-irradiated samples. While pristine specimens showed brittle and subsequent catastrophic failure, the 2.8 MeV Au2+ ion (fluence of 4.378 × 1014 cm−2) irradiated specimens sustained extensive plasticity at room temperature without failure. In situ TEM characterization showed nucleation of nanoscale kink band structures at numerous sites, where the localized plasticity appeared to close the defects and cracks while allowing large average strain. We propose that compressive mechanical stress due to dimensional change during ion irradiation transforms buckled basal layers in graphite into kink bands. The externally applied load during the micropillar tests proliferates the nucleation and motion of kink bands to accommodate the large plastic strain. The inherent non-uniformity of graphite microstructure promotes such strain localization, making kink bands the predominant mechanism behind unprecedented toughness in an otherwise brittle material.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Small-scale mechanical testing and characterization of fuel cladding chemical interaction between HT9 cladding and advanced U-based metallic fuel alloy

Fuel cladding chemical interactions (FCCI) occurred on the interface between the nuclear metal fuel and cladding is the primary cause of cladding wastage, weakening cladding mechanical integrity, and placing fuel and cladding at risk. Although the microstructural and phase information of FCCI has been fairly understood, mechanical properties remain less studied due to limited reaction volume. Here, through a combining of advanced electron microscopy characterizations and small-scale mechanical testing techniques, including indentation and micro-tensile testing, this study investigated the microscale mechanical properties of FCCI between the ferritic/martensitic (F/M) HT9 cladding and an advanced Uranium (U)-based metallic fuel irradiated at the Advanced Test Reactor to 2.2% FIMA with peak inner cladding temperature reached to 650 °C. Mechanical testing results show significant hardening and embrittlement in the FCCI region. The brittle fracture of FCCI specimen is mainly attributed to the formation of nano-crystallized intermetallic σ-FeCr phase. Whereas mechanical softening was revealed in the unreacted HT9 matrix due to irradiation-induced microstructural and microchemical evolution, specifically, the disappearance of martensitic lath structure and the formation of Fe 2 Mo Laves phase precipitation which consumed the solid solution strengthening Mo from the F/M HT9 matrix. Due to the achieved high cladding temperature, this fuel pin is of particular significance for revealing the high-temperature irradiation effect on the mechanical properties of HT9 cladding. Therefore, the outcomes of this study are expected to contribute to the development of multi-scale mechanical behavior modeling of HT9 cladding for Generation IV reactors which requires cladding to run at higher temperature (above 600 ?).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1972

Stress-intensity factors for a surface crack in a finite solid.

A solution to the problem of a circular crack partially embedded in a solid of finite thickness is presented. A superposition and iteration technique is used to determine the stress-intensity factor numerically. The stress-intensity factor is determined as a function of position around the crack front for a variety of crack depths. The results of this study are compared with experimental data for a semielliptical surface flaw in a brittle material.

Thresher, R. W.↗

NASA NTRS1976

On surface energy and the continuum thermodynamics of brittle fracture

When a separating body is viewed as a nonequilibrium thermodynamic process, the full thermodynamic nature of the surface energy induced by crack propagation becomes apparent. Within such a general framework it is no longer possible to view the surface energy as a material constant. For the self-propagating crack the induced surface energy is shown to depend explicitly on the square of the crack propagation speed. It is also shown that a separating body produces entropy even though the mechanical response of the solid may be elastic. The introduction of surface quantities such as surface energy into the continuum description of the fracture process forces a major departure from the mechanics appropriate to the nonseparating body. Local equations of balance are no longer obtainable as derived consequences of postulated global balance equations. They must instead be imposed as separate additional postulates.

Eftis, J.↗

DOE OSTI2025

Comparing the Effects of Side Chain Dipole–Dipole Interactions and Hydrogen Bonding on the Mechanical and Electrical Properties of Poly(3-hexylthiophene)

Poly(3-alkylthiophenes) are simple conjugated polymers with good electrical properties, but tend to be brittle, limiting their application. Here, we investigate how side chain modifications can improve their toughness without compromising their charge transport. Specifically, we compare a weak dipole–dipole interaction of ester groups with a stronger hydrogen-bonding interaction of the hydroxyl groups. Two copolymers with targeted 5 and 10 mol % ester-functionalized side chains were synthesized and hydrolyzed in the solid state to introduce hydroxyl groups. Both hydrolyzed polymers became insoluble in most organic solvents, providing a path to layer-by-layer solution processing. All polymers’ optical, thermal, structural, electrical, and mechanical properties were investigated. Optical spectroscopy revealed that functionalization at these low levels did not significantly affect aggregation or π–π stacking. Differential scanning calorimetry indicated reduced crystallinity in the functionalized copolymers compared to that of P3HT. Grazing-incidence wide-angle X-ray diffraction data showed that functionalization led to an increase in lamellar spacing without altering molecular orientation or π–π stacking. Mechanical testing highlighted that at the lower functionalization level, both ester and hydroxyl groups similarly enhanced toughness, suggesting that disorder, rather than the specific nature of the functional group, was responsible for these improvements. At the higher functionalization level, hydroxyl groups significantly increased the elastic modulus while also negatively impacting charge carrier mobility. This study suggests that with stronger hydrogen-bonding groups, only very small amounts can improve P3HT’s toughness. For a wider tunable range, it may be a better strategy to use weak interactions such as dipole–dipole interactions of ester groups.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Toughening by Nanodroplets: Polymer–Droplet Biocomposite with Anomalous Toughness

The development of new polymer composites is highly dependent on the design of novel fillers that can bring more benefits in the design and control of structure–property–function than conventional solid particles. Here, inspired by the unique coupling structures of tough mussel byssus, we employ nanodroplets of high-boiling-point oligomers as the liquid filler to fabricate a new class of polymer–droplet composites (PDCs). The combination of nanodroplets and chain end/tail modifier in PDCs finally generates soft-coupling structures with chain ends coupled by the nanodroplets. With this strategy, brittle poly(lactic acid) is successfully transformed into a tough bioplastic with toughness improved by over 2000% via a minimal amount of the modifiers (1.5 wt %). Moreover, the composites show unexpected speed-enhanced energy absorption capability. A soft-coupling toughening mechanism is further proposed for the first time to understand the PDCs’ mechanical properties. This work also indicates the potential of nanodroplets as a new tool for tuning the mechanical properties and even functions of polymer composites.

36 MATERIALS SCIENCE↗