Search NASA⌕ Search

SEARCH · Search NASA

Results for “Bumper”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Study of dense aluminum plasmas

Studies directed toward the development of a computer program describing the penetration of a thin aluminum plate by a quartz sphere are reported. The aluminum simulates a bumper plate for micrometeoroids. The ablation of a rock sphere by penetrating a stack of paper sheets is described, and an equation for losses near the surface of the sphere is derived. The expansions of aluminum plasma sphere with initial energies of 44.45, 20.8, and 7.136 eV are investigated, including shock compression during penetration and adiabatic expansion. The equations of state were derived for aluminum and quartz, as well as one of the Mie-Grunesen type. A technique to determine momentum at the bottom surface of the thin plate, and the energy for hypervelocity separation of fragments of the aluminum plate are also considered.

Todd, F. C.↗
NASA NTRS1972

Mechanical component screening for scanner

The critical mechanical components of the scan mirror mechanism are described and their evaluation and screening procedures are discussed. A bumper/damper unit is used in the design to reverse motion of the mirror and effect scan and retrace cycles. A wear evaluation was conducted on the bumper impact surfaces that established nylon 6-10 as an acceptable material. The elastomeric dampers were subjected to thermal vacuum tests for condensables and outgassing as well as parametric life tests. The flexure pivots that support the mirror were tested to establish a curve of stress plotted as a function of cycles to failure for rotational operation. The pivots met the life requirement of 150,000,000 cycles at a + or - 2.9 deg amplitude during fatigue testing. Screening procedures were established for dampers and flexure pivots to obtain flight quality components.

Olson, J. L.↗
NASA NTRS1973

Meteoroid-detector deployment and pressurization systems

The Explorer 46 Meteoroid Technology Satellite (MTS) launched from Wallops Island, Va., August 13, 1972, was configured to fit within the Scout heat shield, 86.36 cm in diameter. In order to package within this envelope, the meteoroid bumper detector panels had to be rolled up unpressurized and secured to the spacecraft main structure. After the spacecraft was placed in orbit the panels were unrolled by a deployment system and inflated by a pressurization system.

Halliday, H. C.↗
NASA NTRS1980

Space radiator trade studies for the 25 kW Power System

Advanced radiator designs which will survive the meteoroid hazard of near earth orbit for five years are evaluated for the 25 kW Power System. Weight comparisons of heat pipe radiators and pumped fluid radiators incorporating meteoroid bumpers are presented for the initial 25 kW Power System and growth versions to 250 kW. The heat pipe concept is enhanced by a new design of the thermal interface between the heat pipe and coolant loop. The results show small weight differences between the advanced heat pipe and pumped fluid concepts for heat loads up to about 50 kW. The heat pipe panels have a weight advantage for larger heat loads.

Howell, H. R.↗
NASA NTRS1980

Device for coupling a first vehicle to a second vehicle

A device is disclosed, carried by a first vehicle such as an orbiting space shuttle, having a plurality of contact members for engaging and holding an annular ring on a second vehicle such as an orbiting payload. The contact members are connected to manipulator arms which are mounted at a fulcrum point and which are moved by an iris type mechanism. Movement of the manipulator arms causes the contact members to grasp or release the annular ring. Bumper devices are provided to axially align the annular ring and draw the contact members into engagement therewith.

Rudmann, A. A.↗
NASA NTRS1981

Study of Thermal Control Systems for orbiting power systems

Thermal control system designs were evaluated for the 25 kW power system. Factors considered include long operating life, high reliability, and meteoroid hazards to the space radiator. Based on a cost advantage, the bumpered pumped fluid radiator is recommended for the initial 25 kW power system and intermediate versions up to 50 kW. For advanced power systems with heat rejection rates above 50 kW the lower weight of the advanced heat pipe radiator offsets the higher cost and this design is recommended. The power system payloads heat rejection allocations studies show that a centralized heat rejection system is the most weight and cost effective approach. The thermal interface between the power system and the payloads was addressed and a concept for a contact heat exchanger that eliminates fluid transfer between the power system and the payloads was developed. Finally, a preliminary design of the thermal control system, with emphasis on the radiator and radiator deployment mechanism, is presented.

Howell, H. R.↗
NASA NTRS1983

Phase-Sensing Guidance for Wire-Following Vehicles

Guidance system for wire-following vehicles tested successfully at speeds exceeding 50 mi/h (80 km/h) on difficult 1 mile (1.6km) course. Unlike previous sensors that compare amplitudes of signals picked up from guide wire, new system compares signal phases. Array of coils is mounted in line along front bumper of vehicle and monitors electromagnetic signal radiating from wire. Guide wire on ground beneath vehicle carrier 6- to 7-kHz alternating current.

Hansen, G. R.↗
NASA NTRS1982

A remote computer graphics user at General Motors

The successful use of automotive body surface design data is described. This data has been originally created elsewhere in GM's two large computer graphics systems of CADANCE and Fisher Graphics. As a supplier exterior lighting components, radiator grilles, energy absorbing soft faced bumper systems, and other associated items, Guide has become most dependent on the corporate computer graphics systems to supply accurate car body styling and sheet metal surfacing information for the design of their products. The presentation includes the origin and transfer of design data to a remote user site; its use in the design of their products; and the ultimate production of detailed drawings, N/C punched tapes, and subsequent downstream transfers of detailed part data to a turnkey system for tool design purposes.

Murphy, H. S.↗
NASA NTRS1984

Multiple-foil microabrasion package (A0023)

The specific scientific objectives of this experiment are to measure the spatial distribution, size, velocity, radiance, and composition of microparticles in near-Earth space. The technological objectives are to measure erosion rates resulting from microparticle impacts and to evaluate thin-foil meteor 'bumpers'. The combinations of sensitivity and reliability in this experiment will provide up to 1000 impacts per month for laboratory analysis and will extend current sensitivity limits by 5 orders of magnitude in mass.

Mcdonnell, J. A. M.↗
NASA NTRS1984

Project Explorer: Get Away Special #007

Tentatively scheduled to fly on STS-17 (41G), this get away special aims to demonstrate amateur radio transmissions to global ground stations in the English language. Experiments No. 1, 2, and 3 use the micro-gravity of space flight to study the solidification of lead-antimony and aluminum-copper alloys, the germination of radish seeds, and the growth of potassium-tetracyanoplatinate hydrate crystals in an aqueous solution. Flight results are to be compared with Earth-based data. Experiment No. 4 (the Marshall Amateur Radio Club Experiment - MARCE) features radio transmissions and also provides timing for the start of all other experiments. A microprocessor obtains real-time data from all experiments as well as temperature and pressure measurements within the GAS canister. These data are to be transmitted on previously announced amateur radio frequencies after they are converted into the English language by a digitalker for general reception. The support structure for the G #007 experiments consists of two primary plates and four bumper assemblies.

Henderson, A. J., Jr.↗
NASA NTRS1984

Linear magnetic bearings

A self regulating, nonfrictional, active magnetic bearing is disclosed which has an elongated cylindrical housing for containing a shaft type armature with quadrature positioned shaft position sensors and equidistantly positioned electromagnets located at one end of the housing. Each set of sensors is responsive to orthogonal displacement of the armature and is used to generate control signals to energize the electromagnets to center the armature. A bumper magnet assembly is located at one end of the housing for dampening any undesired axial movement of the armature or to axially move the armature either continuously or fixedly.

Goldowskiy, M. P.↗
NASA NTRS1985

Manmade orbital debris studies at NASA Langley

In the past, flight experiments to define the meteoroid environment near the Earth and in interplanetary space were undertaken. The effectiveness of meteoroid bumpers was investigated. These flight experiments were aboard Pioneer 10, Pioneer 11, and Explorer 46. Hypervelocity impact tests were conducted in the laboratory to study protective structures and the composition of meteoroids from the hundreds of meteor spectra obtained. It was also found that manmade debris presented a similar hazard to spacecraft near the Earth. An assessment of that hazard is made in this paper. An analysis of the collision probability problem with much attention given to the population of small untrackable fragments created during explosions is presented.

Humes, D. H.↗