Search NASA⌕ Search

SEARCH · Search NASA

Results for “CADMIUM TELLURIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Mapping Current Collection in Cross Section: The Case of Copper-Doped CdTe Solar Cells

For decades, copper has been used to improve the performance of cadmium telluride thin film solar cells. However, it has also been shown to be the main cause of metastability in CdTe. Recently a low activation energy has been reported for the thermal diffusion of Cu in CdTe explaining the ease of motion that it has under moderate temperatures. The community consensus is that copper segregates to the absorber grain boundaries, where it's either beneficial or detrimental to device performance depending on its concentration. Using nanoscale X-ray micrsocopy and a two-dimensional drift-diffusion model we present a preliminary correlation between local copper distribution and electrical performance of a single-junction CdTe/CdS solar cell.

CdTe↗
DOE OSTI2023

The Effect of Dopant Concentration and Annealing Treatments on N-Type Iodine Doped CdTe

We report properties of highly conducting n-type cadmium telluride single crystals doped with iodine (CdTe:I). These crystals were grown with dopant concentrations in the range of 10^17 cm-3 to 10^19 cm-3 by Modified Vertical Bridgman (MVB) melt growth. Post-growth dopant activation, including Cd annealing, Te annealing, and rapid thermal annealing (RTA), was applied to improve free carrier density. The structural, optical, and electrical properties were analyzed by Glow Discharge Mass Spectroscopy (GDMS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Photoluminescence Spectroscopy (PL), optical absorption, Hall measurements, Capacitance-Voltage (CV) measurements, and time-resolved photoluminescence (TRPL). The results indicate that Cd annealing is the most effective activation method to get 100% donor activation (n is approximately 2 x 10^18 cm-3), which is close to the room temperature solubility limit of iodine. This leads to the lowest resistivity and the highest mobility. Moreover, this data suggests a potential role of Cd vacancy-related defects on electrical self-compensation.

annealing↗
NASA NTRS1995

Experimental Studies on Mass Transport of Cadmium-Zinc Telluride by Physical Vapor Transport

Experimental studies on mass transport of ternary compound, Cd(1-x)Zn(x)Te by physical vapor transport (PVT) for source compositions up to X = 0.21 are presented. The effect of thermochemical (temperatures, vapor composition) and other factors (preparation of the source, crystal growth rate, temperature gradient) on composition and composition profiles of the grown crystals were investigated. A steep decrease in the mass flux with an increase in X(crystal) for X less than 0.1, and a difference in composition between the source and the deposited material have been observed. The composition profiles of the crystals were found to depend on the density and pretreatment of the source, and on the temperature gradient in the source zone. The homogeneity of the crystals improves at low undercoolings and/or when an appropriate excess of metal constituents is present in the vapor phase. The experimental results are in good agreement with our thermochemical model of this system.

Palosz, W.↗
NASA NTRS1997

Characterization of Cadmium-Zinc Telluride Crystals Grown by 'Contactless' PVT Using Synchrotron White Beam Topography

Crystals of Cd(1-x)Zn(x)Te grown by Physical Vapor Transport (PVT) using self-seeding 'contactless' techniques were characterized using synchrotron radiation (reflection, transmission, and Laue back-reflection X-ray topography). Crystals of low (x = 0.04) and high (up to x approx. = 0.4) ZnTe content were investigated. Twins and defects such as dislocations, precipitates, and slip bands were identified. Extensive inhomogeneous strains present in some samples were found to be generated by interaction (sticking) with the pedestal and by composition gradients in the crystals. Large (up to about 5 mm) oval strain fields were observed around some Te precipitates. Low angle grain boundaries were found only in higher ZnTe content (x greater than or equal to 0.2) samples.

Palosz, W.↗
NASA NTRS2012

Blocking contacts for N-type cadmium zinc telluride

A process for applying blocking contacts on an n-type CdZnTe specimen includes cleaning the CdZnTe specimen; etching the CdZnTe specimen; chemically surface treating the CdZnTe specimen; and depositing blocking metal on at least one of a cathode surface and an anode surface of the CdZnTe specimen.

Stahle, Carl M.↗
DOE OSTI2021

Characterization of CdZnTeSe Nuclear Detector Chemically Etched in Bromine Methanol

Semiconductor nuclear radiation detectors made from tertiary and quaternary compounds of cadmium telluride (CdTe) can operate at room temperature without cryogenic cooling. One of such materials that have become of great interest is cadmium zinc telluride selenide (CdZnTeSe). Compared to other CdTe-based materials, such as cadmium zinc telluride (CdZnTe), CdZnTeSe can be grown with much less Te inclusions and sub-grain boundary networks. Chemical etching is often used to smoothen wafer surfaces during detector fabrication. This paper presents the characterization of CdZnTeSe that is chemically etched using bromine methanol solution. Infrared imaging shows that the wafer has no sub-grain boundary networks that often limit detector performance. The current-voltage (I-V) characterization experiment gave a resistivity of 4.6 × 10 10 Ω-cm for the sample. The I-V curve was linear in the ±10 to ±50 volts range. An energy resolution of 7.2% was recorded at 100 V for the 59.6-keV gamma line of 241 Am.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Water-Assisted Lift-Off Process for Flexible CdTe Solar Cells

In recent years, various lift-off methods have been developed to fabricate lightweight and flexible cadmium telluride (CdTe)-based solar cells. In this work, we report flexible cadmium sulfide (CdS)/CdTe solar cells using a water-assisted lift-off approach. Here we demonstrate that an additional cadmium chloride treatment for the CdS film is critical to improve the grain size of CdS and the post-deposited CdTe film and the electron conductivity of the CdS film. As a result, the quality of the CdS/CdTe front junction is significantly improved with reduced nonradiative recombination. Finally, our lightweight and flexible polycrystalline CdTe solar cells demonstrate a champion power conversion efficiency of 12.6%.

14 SOLAR ENERGY↗
NASA NTRS2011

High Speed, Multi-Channel, Thermal Instrument Development in Support of HyspIRI-TIR

The Jet Propulsion Laboratory is currently developing an end-to-end instrument which will provide a proof of concept prototype vehicle for a high data rate, multi-channel, thermal instrument in support of the Hyperspectral Infrared Imager (HyspIRI)-Thermal Infrared (TIR) space mission. HyspIRI mission was recommended by the National Research Council Decadal Survey (DS). The HyspIRI mission includes a visible shortwave infrared (SWIR) pushboom spectrometer and a multispectral whiskbroom thermal infrared (TIR) imager. The prototype testbed instrument addressed in this effort will only support the TIR. Data from the HyspIRI mission will be used to address key science questions related to the Solid Earth and Carbon Cycle and Ecosystems focus areas of the NASA Science Mission Directorate. Current designs for the HyspIRI-TIR space borne imager utilize eight spectral bands delineated with filters. The system will have 60m ground resolution, 200mK NEDT, 0.5C absolute temperature resolution with a 5-day repeat from LEO orbit. The prototype instrument will use mercury cadmium telluride (MCT) technology at the focal plane array in time delay integration mode. A custom read out integrated circuit (ROIC) will provide the high speed readout hence high data rates needed for the 5 day repeat. The current HyspIRI requirements dictate a ground knowledge measurement of 30m, so the prototype instrument will tackle this problem with a newly developed interferometeric metrology system. This will provide an absolute measurement of the scanning mirror to an order of magnitude better than conventional optical encoders. This will minimize the reliance on ground control points hence minimizing postprocessing (e.g. geo-rectification computations).

Multi-spectral↗
DOE OSTI2021

Dual-Wavelength Time-Resolved Photoluminescence Study of CdSe x Te 1-x Surface Passivation via Mg y Zn 1-y O and Al 2 O 3

Voltage loss is currently one of the biggest challenges facing cadmium telluride (CdTe) based photovoltaics. Determining the location(s) of major voltage loss within the device stack (e.g., front/back interface, grain boundaries) is therefore of primary interest. Here, we present a custom-built time-resolved photoluminescence system with two excitation wavelengths - 670 (standard) and 405 nm - to probe the device stack at depths of approximately 130 and 35 nm, respectively; their comparison helps differentiate interface and bulk contributions to carrier lifetime. We apply this system to examine the passivation effect of two significant recent advances in CdTe: the incorporation of Se to form graded CdSe x Te 1-x and the replacement of CdS with Mg y Zn 1-y O. It is found that x = 0.2 Se is required to obtain lifetime improvements, primarily in the bulk. Additionally, evidence for trapping at the Mg y Zn 1-y O/CdSe x Te 1-x interface was observed. Furthermore, this indicates further work is required to sufficiently passivate the front interface.

CdSeTe↗
DOE OSTI2021

Is 3D/2D Passivation a Secret to Success for Polycrystalline Thin-Film Solar Cells?

Three leading thin-film photovoltaic (PV) technologies - cadmium telluride (CdTe), CuIn1-xGaxSe2 (CIGS), and perovskite solar cells (PSCs) - are all polycrystalline, but otherwise appear to have little in common. A comprehensive examination of these technologies, however, reveals a common theme: the formation of two-dimensional (2D) van der Waals materials at three-dimensional (3D) absorber interfaces and grain boundaries. In CdTe, the 2D compound is CdCl2; in CIGS, it is XInSe2 (X= K, Rb, Cs) with X depending on the heavy-alkali post-deposition treatment used; and in lead halide PSCs, PbI2 forms naturally, but many new, more stable, 2D perovskites have also been incorporated. Generally, these 2D interfacial materials are present not by design, but instead have evolved from their 3D counterparts during standard device processing. Here, new data, together with evidence compiled from the literature, are presented to illustrate both the existence of 3D/2D interfaces in CdTe, CIGS, and PSCs, and their correlation with improved passivation and device performance. This suggests that 3D/2D passivation may be a heretofore unappreciated key to successful polycrystalline thin-film PV. Finally, the desired attributes of successful low-dimensional layers are presented with rational design strategies for next generation polycrystalline solar cells.

3D/2D↗
DOE OSTI2023

Distribution of Copper States, Phases, and Defects across the Depth of a Cu-Doped CdTe Solar Cell

Copper has been used as a p-type dopant in cadmium telluride (CdTe) for decades. However, the density of Cu atoms in the finished device is much higher than that of holes, which means that most Cu atoms are not activated as acceptors during incorporation. Furthermore, studies have demonstrated that the distribution of copper (Cu) atoms across the device is highly inhomogeneous, with reports citing Cu substitution on Cd sites and segregation to grain boundaries. Fast diffusion along these boundaries and Cu accumulation at the CdTe/CdS interface have also been observed and validated computationally. These levels of inhomogeneity make it difficult to accurately characterize and correlate the performance with the nature of the Cu atomic species present. To address this challenge, we utilize X-ray microscopy and, specifically, nanoscale fluorescence-mode X-ray absorption near-edge structure to resolve the atomic Cu environment throughout the depth of the CdTe layer. Our results suggest that the majority of Cu atoms are in the form of Cu x Te phases (or similar local environments) near the ZnTe|CdTe interface, Cu x O phases in the CdTe absorber, and present in various oxidation states, including Cu 1+ and Cu 2+ , near the CdS/CdTe junction. Here this work also provides experimental evidence for the first time of the presence of CuS around the ZnTe|CdTe interface and the hypothesized Cu Cd -Cl i complex in the CdTe absorber.

14 SOLAR ENERGY↗
DOE OSTI2022

Impact of dopant-induced band tails on optical spectra, charge carrier transport, and dynamics in single-crystal CdTe

Abstract Cadmium telluride (CdTe) semiconductors are used in thin-film photovoltaics, detectors, and other optoelectronic applications. For all technologies, higher efficiency and sensitivity are achieved with reduced charge carrier recombination. In this study, we use state-of-the-art CdTe single crystals and electro-optical measurements to develop a detailed understanding of recombination rate dependence on excitation and temperature in CdTe. We study recombination and carrier dynamics in high-resistivity (undoped) and arsenic (As)-doped CdTe by employing absorption, the Hall effect, time-resolved photoluminescence, and pump-probe in the 80–600 K temperature range. We report extraordinarily long lifetimes (30 µs) at low temperatures in bulk undoped CdTe. Temperature dependencies of carrier density and mobility reveal ionization of the main acceptors and donors as well as dominant scattering by ionized impurities. We also distinguish different recombination defects. In particular, shallow As Te and deep V Cd −As Cd acceptors were responsible for p-type conductivity. AX donors were responsible for electron capture, while nonradiative recombination centers (V Cd −As Te , As 2 precipitates), and native defects (V Cd −Te Cd ) were found to be dominant in p-type and n-type CdTe, respectively. Bimolecular and surface recombination rate temperature dependencies were also revealed, with bimolecular coefficient T −3/2 temperature dependence and 170 meV effective surface barrier, leading to an increase in surface recombination velocity at high temperatures and excitations. The results of this study allowed us to conclude that enhanced crucible rotation growth of As-doped CdTe is advantageous to As activation, leading to longer lifetimes and larger mobilities and open-circuit voltages due to lower absorption and trapping.

36 MATERIALS SCIENCE↗
DOE OSTI2023

CdTe-based thin film photovoltaics: Recent advances, current challenges and future prospects

Cadmium telluride (CdTe)-based cells have emerged as the leading commercialized thin film photovoltaic technology and has intrinsically better temperature coefficients, energy yield, and degradation rates than Si technologies. More than 30 GW peak (GWp) of CdTe-based modules are installed worldwide, multiple companies are in production, modules are shipping at up to 18.6% efficiency, and lab cell efficiency is above 22%. We review developments in the science and technology that have occurred over approximately the past decade. These achievements were enabled by manufacturing innovations and scaling module production, as well as maximizing photocurrent through window layer optimization and alloyed CdSe x Te 1-x (CST) absorbers. Improved chlorine passivation processes, film microstructure, and serendipitous Se defect passivation significantly increased minority carrier lifetime. Efficiencies >22% have been realized for both Cu and As doped CST-based cells. The path to further efficiency gains hinges primarily on increasing open circuit voltage (V oc ) and fill factor (FF) through innovations in materials, fabrication methods, and device stacks. Replacing the longstanding Cu doping with As doping is resulting in better module stability and is being translated to large-scale production. To realize 25% efficiency and >1 V V oc , research and development is needed to increase the minority carrier lifetime beyond 100 ns, reduce grain boundary and interface recombination, and tailor band diagrams at the front and back interfaces. Many of these goals have been realized separately however combining them together using scalable manufacturing approaches has been elusive to date. We review these achievements and outstanding opportunities for this remarkable photovoltaic technology.

14 SOLAR ENERGY↗
NASA NTRS1999

Growth of II-VI Solid Solutions in the Presence of a Rotating Magnetic Field

The application of a rotating magnetic field (RMF)in the frequency range 60-400 Hz and field strength of the order of 2-8 mT to crystal growth has received increasing attention in recent years. To take full advantage of the control of fluid flow by the forces applied by the field, the liquid column must be electrically conducting. Also, the application of RMF to the directional solidification of a column of liquid can result in complete mixing in the resultant solid. Thus, the technique of RMF is suited to solvent zones and float zones where the composition of the liquid is more readily controlled. In the work we report on, numerical modeling has been applied to II-VI systems, particularly tellurium based traveling heater techniques (THM). Results for a spectrum of field strengths and acceleration levels will be presented. These show clearly the effects of competing buoyancy forces and electromagnetic stirring. Crystals of cadmium zinc telluride and mercury cadmium telluride have been grown terrestrially from a tellurium solvent zone. The effects of the RMF during these experiments will be demonstrated with micrographs showing etch pits, white beam x-ray synchrotron topographs and triple axis x-ray diffraction.

Gillies, D. C↗