Search NASA⌕ Search

SEARCH · Search NASA

Results for “CENTRIFUGAL FORCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Long-term effects of microgravity and possible countermeasures

The measures that can be taken to counteract the effect of long-term exposures to microgravity are discussed. It is noted that, although it was shown that specially designed exercise programs can counteract the effect of exposures of up to one year in space, is it questionable whether U.S. astronauts could or should have to maintain such regimes for extremely prolonged missions. The methods considered by NASA Life Sciences Division are to provide an artificial gravity environment by the generation of centrifugal forces by means of either the continuous rotation of the whole spacecraft or using a short-arm centrifuge on board a zero-g spacecraft. Results obtained in studies of these two methods are discussed, and the centrifuge research facility that is presently being developed by NASA is described.

Wolfe, James W.↗
NASA NTRS1989

A theoretical study of fluid forces on a centrifugal impeller rotating and whirling in a vaned diffuser

The fluid forces on a centrifugal impeller rotating and whirling in a vaned diffuser are analyzed on the assumption that the number of impeller and diffuser vanes is so large that the flows are perfectly guided by the vanes. The flow is taken to be two dimensional, inviscid, and incompressible, but the effects of impeller and diffuser losses are taken into account. It is shown that the interaction with the vaned diffuser may cause destabilizing fluid forces. From these discussions, it is found that the whirling forces are closely related to the steady head-capacity characteristics of the impeller. This physical understanding of the whirling forces can be applied also to the cases with volute casings. At partial capacities, it is shown that the impeller forces change greatly when the flow rate and whirl velocity are near to the impeller or vaned diffuser attributed rotating stall onset capacity, and the stall propagation velocity, respectively. In such cases the impeller forces may become destabilizing for impeller whirl.

Tsujimoto, Yoshinobu↗
NASA NTRS1978

Counter pumping debris excluder and separator

A dirt separator and excluder for removing entrained debris from gas turbine shaft seals is described. A helical groove pattern is constructed on the rotating shaft with the pumping pattern such that it tends to pump seal pressurizing gas toward the gas turbine seal. A second helical groove pattern is provided on the stationary housing or counter rotating member coaxial with the shaft, and this pattern is designed to provide pumping in the direction opposite from that of the groove pattern on the shaft. Gas with entrained debris entering this grooved area will be subjected to high centrifugal forces due to the swirl motion induced by the groove pattern and the rotation of the shaft. This debris is centrifuged outwardly into the outer groove pattern on the housing or counter rotating member. Because the outer groove pattern has a pumping direction opposite from that of the seal, dirt is pumped away from the seal and can be collected in a suitable debris trap remote from the seal location.

Ludwig, L. P.↗
NASA NTRS1966

Flexible arms provide constant force for pressure switch calibration

In-place calibration of a pressure switch is provided by a system of radially oriented flexing arms which, when rotated at a known velocity, convert the centrifugal force of the arms to a linear force along the shaft. The linear force, when applied to a pressure switch diaphragm, can then be calculated.

Cain, D. E.↗
NASA NTRS1990

The rotordynamic forces on a centrifugal pump impeller in the presence of cavitation

Fluid-induced rotordynamic forces on a centrifugal pump impeller whirling along a trajectory eccentric to its undeflected position in the presence of cavitation were measured using the experimental facility described by Jery (1987). The force measured is a combination of a steady radial force due to the volute asymmetries and an unsteady force due to the eccentric motion of the rotor. It was found that, compared to the noncavitation condition, a cavitation corresponding to a head loss of 3 percent had little effect upon the unsteady force. However, a lesser degree of cavitation at the design point, was found to increase the destabilizing force for a particular set of whirl ratios.

Franz, R.↗
NASA NTRS1988

Theoretical study of fluid forces on a centrifugal impeller rotating and whirling in a volute

Fluid forces on a rotating and whirling centrifugal impeller in a volute are analyzed with the assumption of a two-dimensional rotational, inviscid flow. For simplicity, the flow is assumed to be perfectly guided by the impeller vanes. The theory predicts the tangential and the radial force on the whirling impeller as functions of impeller geometry, volute spacing, and whirl ratio. A good qualitative agreement with experiment is found.

Tsujimoto, Y.↗
NASA NTRS1985

Fluid surface behavior in low gravity. Center discretionary fund no. 83-21

Measurements of rotating equilibrium bubble shapes in the low-gravity environment of a free-falling aircraft are presented. Emphasis is placed on bubbles which intersect the container boundaries. These data are compared with theoretical profiles derived from Laplace's formula and are in good agreement with the measurements. Two types of instability are explored. The first occurs when the baffle spacing is too large for the bubble to intersect both the top and bottom boundaries. The second occurs when the hydrostatic pressure beneath a displaced free surface does not compensate for pressure change due to capillary forces. The interface shape depends on the contact angle, the radius of intersection with container, and the parameter F which is a measure of the relative importance of centrifugal force to surface tension. For isolated bubbles, F has a maximum value of 1/2. A further increase in F causes the bubble to break contact with the axis of rotation. For large values of F, the bubble becomes more cylindrical and the capillary rise occurs over a thinner layer so that the small radius of curvature can generate enough pressure drop to balance the increased hydrostatic contribution.

Leslie, F.↗
NASA NTRS1984

Laminar flow effects in the coil planet centrifuge

The coil planet centrifuge designed by Ito employs flow of a single liquid phase, through a rotating coiled tube in a centrifugal force field, to provide a separation of particles based on sedimentation rates. Mathematical solutions are derived for the linear differential equations governing particle behavior in the coil planet centrifuge device. These solutions are then applied as the basis of a model for optimizing particle separations.

Herrmann, F. T.↗
NASA NTRS1986

Deployable Truss Member

Compact telescoping roll extends 24 times its length. Roll telescopes into extended truss member when force is applied. Truss members deployed by various means. Truss member initially constructed in its stowed state with appropriate sheet material rolled around central core. For deployment truss extends by centrifugal force to form cone. With both ends fastened to prevent unrolling, rigid truss member formed.

Frink, N. T.↗
NASA NTRS1999

Control of a Thrust Alignment Table for Modeling the Coning Dynamics of a Spinning Spacecraft with a Follower Force

This document presents a system controlling the motion of a spherical air bearing used in the modeling of spacecraft dynamics and controls in a laboratory environment. The system is part of the Spinning Rocket Simulator (SRS), used to simulate the coning of spacecraft during a thrusting stage. The reaction force at the spherical air bearing supporting the spacecraft model must coincide with the thrust axis of the model for proper simulation. Therefore, the bearing is translated in a circular path to introduce a centrifugal force. This horizontal force along with the gravitational reaction force at the bearing combines to simulate the direction of the spacecraft's thrust force. The control system receives attitude information from the spacecraft model via a laser beam embedded in the model that impinges on a photosensitive array. The non-linear system is controlled using high-speed lookup tables and digital techniques. A vector-controlled motor and a stepper motor are given the necessary signals to accurately control the turntable and platform supporting the air bearing. Preliminary performance data is presented. Mechanical elements of the table and platform are described in detail. A wireless (RF) data path for all devices on the spacecraft model to an off-table command computer is also described.

Halsmer, Dominic↗
NASA NTRS2024

Effect of High-Speed Rotation on High-Temperature Superconducting Coils for High Efficiency Megawatt Motor

The use of a superconducting rotor in the High Efficiency Megawatt Motor (HEMM) comes with a number of challenges. The HEMM’s rotor must be designed so that the superconducting coil can tolerate the forces it will encounter during operation. These forces introduce considerable risk to the design of the HEMM. Because this risk cannot be adequately addressed through refined analysis, a set of experiments was deemed necessary to demonstrate that the HEMM’s superconducting coils can survive the stresses imparted by the centrifugal forces acting on the coil during full-speed operation of the machine. These experiments required spin testing a full-scale HEMM coil on a representative rotor structure at room temperature and sequentially higher rotation speeds and measuring the superconductivity response of the coil in liquid nitrogen (LN2) before and after each spin test. Tests were carried out to the full centripetal loading of a recent HEMM design. According to finite element analysis, this load produced stress components in the coil that exceed their design limit by a factor of 1 to 7.4. Although not yet confirmed, the current HEMM design is expected to produce even smaller stresses in the coil due to a 20 percent reduction in the coil’s mass and an increased volume of structural material. The only degradation of the coil that occurred during this testing resulted from a test rig failure and from the voltage taps, which are not part of the final coil design.

Electrified Aircraft Propulsion↗
DOE OSTI2025

NFE-24-10417: Durability and Life-time Energy Performance Enhancement of Vapor Compression Systems

This project investigated the use of a Centrifugal Particle Separation (CPS) system to improve the durability and operational reliability of outdoor heat exchangers in vapor-compression based heating, ventilation, air conditioning, and refrigeration (HVACR) systems. The developed method introduced a novel dust and fouling mitigation approach by integrating an ambient air pre-cleaner that employs centrifugal forces to remove particulate matter from incoming air before it reaches the heat exchanger. By reducing the accumulation of dust and debris on coil surfaces, the CPS system aims to lower maintenance requirements and extend equipment lifespan. The project specifically involves coupling a centrifugal air pre-cleaner with a single-zone ductless mini-split system and evaluating its effectiveness in maintaining cleaner coil surfaces. Additionally, the study examined the impact of CPS integration on system energy performance. Through controlled experimental testing and performance monitoring, this work seeks to validate CPS-based air pre-cleaning as a practical, efficient solution for mitigating outdoor coil dust accumulation and fouling in both residential and commercial HVACR applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS2006

Decrease in T Cell Activation and Calcium Flux during Clinorotation

We investigated the effect of altered gravitational environments on T cell activation. We isolated human, naive T cells (CD3+CD14-CD19-CD16-CD56-CD25-CD69-CD45RA-) following IRB approved protocols. These purified T cells were then incubated with 6 mm polystyrene beads coated with OKT3 (Ortho Biotech, Raritan, NJ) and antiCD28 (Becton Dickinson (BD), San Jose, CA) at 37 C for 24 hours. Antibodies were at a 1:1 ratio and the bead-to-cell ratio was 2:1. Four incubation conditions existed: 1) static or "1g"; 2) centrifugation at 10 relative centrifugal force (RCF) or "10g"; 3) clinorotation at 25 RPM (functional weightlessness or "0g"); and 4) clinorotation at 80 RPM ("1g" plus net shear force approx.30 dynes/sq cm). Following incubation, T cells were stained for CD25 expression (BD) and intracellular calcium (ratio of Fluo4 to Fura Red, Molecular Probes, Eugene, OR) and analyzed by flow cytometry (Coulter EPICS XL, Miami, FL). Results: Static or "1g" T cells had the highest level of CD25 expression and intracellular calcium. T cells centrifuged at 10 RCF ("10g") had lower CD25 expression and calcium levels compared to the static control. However, cells centrifuged at 10 RCF had higher CD25 expression and calcium levels than those exposed to 24 RPM clinorotation ("0g"). T cells exposed to 24 RPM clinorotation had lower CD25 expression, but the approximately the same calcium levels than T cells exposed to 80 RPM clinorotation. These data suggest that stress-activated calcium channel exist in T cells and may play a role during T cell activation.

Sams, Clarence↗
NASA NTRS1989

Using NASTRAN To Analyze Vibrations Of Rotor Blades

Report gives information on use of NASTRAN computer program in finite-element analysis of rotating flexible blades like in compressors and on turboprop engines. Predicts steady-state components of deflections and stresses under centrifugal forces, generates data for plots of natural frequency versus rotational speed, and provides vibration-mode data for calculations of flutter. Describes use of NASTRAN solution sequence 64 for geometrical nonlinear analysis and solution sequence 63 for determination of frequencies and vibrational-mode shapes. Includes sample problem with NASTRAN input data. Emphasizes key factors in analysis of rotating blades, such as setting angle and centrifugal softening effects. Combined analyses of solution sequences 64 and 63 reduces computer time and number of output listings, in comparison with separate analyses. In central-processing-unit time cut in half.

Lawrence, Charles↗
NASA NTRS1989

Structural analysis of a thermal insulation retainer assembly

In January 1989 an accident occurred in the National Transonic Facility wind tunnel at NASA Langley Research Center that was believed to be caused by the failure of a thermal insulation retainer. A structural analysis of this retainer assembly was performed in order to understand the possible failure mechanisms. Two loading conditions are important and were considered in the analysis. The first is the centrifugal force due to the fact that this retainer is located on the fan drive shaft. The second loading is a differential temperature between the retainer assembly and the underlying shaft. Geometrically nonlinear analysis is required to predict the stiffness of this component and to account for varying contact regions between various components in the assembly. High, local stresses develop in the band part of the assembly near discontinuities under both the centrifugal and thermal loadings. The presence of an aluminum ring during a portion of the part's operating life was found to increase the stresses in other regions of the band. Under the centrifugal load, high bending stresses develop near the intersection of the band with joints in the assembly. These high bending stresses are believed to be the most likely cause for failure of the assembly.

Greene, William H.↗
NASA NTRS1990

One-dimensional analysis of the hydrodynamic and thermal characteristics of thin film flows including the hydraulic jump and rotation

The flow of a thin liquid film with a free surface along a horizontal plane that emanates from a pressurized vessel is examined numerically. In one g, a hydraulic jump was predicted in both plane and radial flow, which could be forced away from the inlet by increasing the inlet Froude number or Reynolds number. In zero g, the hydraulic jump was not predicted. The effect of solid-body rotation for radial flow in one g was to 'wash out' the hydraulic jump and to decrease the film height on the disk. The liquid film heights under one g and zero g were equal under solid-body rotation because the effect of centrifugal force was much greater than that of the gravitational force. The heat transfer to a film on a rotating disk was predicted to be greater than that of a stationary disk because the liquid film is extremely thin and is moving with a very high velocity.

Thomas, S.↗
NASA NTRS1992

Combined forced and free convection in a curved duct

The purpose of this study is to investigate the flow and heat transfer characteristics of a combined forced and free convection flow in a curved duct. Solutions are obtained by solving the low Mach number model of the Navier-Stokes equation using a control volume method. The finite-volume method was developed with the use of a predictor-corrector numerical scheme and some new variations of the classical projection method. Solutions indicated that the existence of a buoyancy force has changed the entire flow structure inside a curved duct. Reversed flow at both inner and outer bend is observed. For moderate Reynolds number, the upstream section of the duct was significantly influenced by the free convection processes. In general, heat transfer is strong at the inner bend of the beginning of the heated section and at the outer bend on the last half of the heated section. The maximum velocity location is strongly influenced by the combined effects of buoyancy and centrifugal forces. A strong buoyancy force can reduce the strength of the secondary flow where it plays an important role in mixing.

Yam, Clement G.↗
DOE OSTI2020

Characterization and Scaling of Forced Convective Swirl in Sinusoidal Wavy-Plate-Fin Cores of Compact Heat Exchangers

The characterization and scaling of the thermal-hydraulic performance in wavy plate-fin compact heat exchanger cores, based on the understanding of the physical phenomena and heat transfer enhancement mechanism is delineated. Experimental data are presented for forced convection in air (Pr = 0.71) with flow rates in the range 50 ≤ Re ≤ 4000. A variety of wavy-fin cores that span viable applications, with geometrical attributes described by the cross section aspect ratio α (ratio of fin spacing to height), fin corrugation aspect ratio γ (ratio of 2× corrugation amplitude to wave pitch), and fin spacing ratio ζ (ratio of fin spacing to wave pitch), are considered. To characterize and correlate the vortex-flow mixing in interfin spaces, a Swirl number Sw is introduced from the balance of viscous, inertial and centrifugal forces. It is shown that the laminar, transitional and turbulent flow regimes can be explicitly identified by this Swirl number. Based on the experimental results and extended analysis, new correlations for Fanning friction factor f and Colburn factor j are developed with Sw, α, γ, and ζ as scaling parameters. Requisite expressions are devised by a superposition of both enhancement components due to the corrugated surface area enlargement and induced swirl flow field, and they are combined to cover the laminar, transitional and turbulent regimes by the method of asymptotic matching. The resulting generalized correlations are further shown to predict all available experimental data for f and j factors to within ±20% and ±15%, respectively.

42 ENGINEERING↗