Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPRESSION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Experimental Studies of Low-Load Limit in a Stoichiometric Micro-Pilot Diesel Natural Gas Engine

While operating at light loads, diesel pilot-ignited natural gas engines with lean premixed natural gas suffer from poor combustion efficiency and high methane emissions. This work investigates the limits of low-load operation for a micro-pilot diesel natural gas engine that uses a stoichiometric mixture to enable methane and nitrogen oxide emission control. By optimizing engine hardware, operating conditions, and injection strategies, this study focused on defining the lowest achievable load while maintaining a stoichiometric equivalence ratio and with acceptable combustion stability. A multi-cylinder diesel 6.7 L engine was converted to run natural gas premix with a maximum diesel micro-pilot contribution of 10%. With a base diesel compression ratio of 17.3:1, the intake manifold pressure limit was 80 kPa(absolute). At a reduced compression ratio of 15:1, this limit increased to 85 kPa, raising the minimum stable load. Retarding the combustion phasing, typically used in spark-ignition engines to achieve lower loads, was also tested but found to be limited by degraded diesel ignition at later timings. Reducing the pilot injection pressure improved combustion stability, as did increasing pilot quantity at the cost of lower substitution ratios. The lean operation further reduced load but increased NOx and hydrocarbon emissions. At loads below the practical dual-fuel limit, a transition to lean diesel operation will likely be required with corresponding implications for the aftertreatment system.

03 NATURAL GAS↗
NASA NTRS1944

The Effect of Piston-Head Temperature on Knock-Limited Power

To determine the effect of piston-head temperature on knock-limited power. Tests were made in a supercharged CFR engine over a range of fuel-air ratios from 0.055 to 0.120, using S-3 reference fuel, AN-F-28, Amendment-2, aviation gasoline, and AN-F-28 plus 2 percent xylidines by weight. Tests were run at a compression ratio of 7.0 with inlet-air temperatures of 150 F and 250 F and at a compression ratio of 8.0 with an inlet-air temperature of 250 F. All other engine conditions were held constant. The piston-head temperature was varied by circulation of oil through passages in the crown of a liquid-cooled piston. This method of piston cooling decreased the piston-head temperature about 80 F. The data are not intended to constitute a recommendation as to the advisability of piston cooling in practice.

Imming, Harry S.↗
NASA NTRS1932

Influence of several factors on ignition lag in a compression-ignition engine

This investigation was made to determine the influence of fuel quality, injection advance angle, injection valve-opening pressure, inlet-air pressure, compression ratio, and engine speed on the time lag of auto-ignition of a Diesel fuel oil in a single-cylinder compression-ignition engine as obtained from an analysis of indicator diagrams. Three cam-operated fuel-injection pumps, two pumps cams, and an automatic injection valve with two different nozzles were used. Ignition lag was considered to be the interval between the start of injection of the fuel as determined with a Stroborama and the start of effective combustion as determined from the indicator diagram, the latter being the point where 4.0 x 10(exp-6) pound of fuel had been effectively burned. For this particular engine and fuel it was found that: (1) for a constant start and the same rate of fuel injection up the point of cut-off, a variation in fuel quantity from 1.2 x 10(exp-4) to 4.1 x 10(exp-4) pound per cycle has no appreciable effect on the ignition lag; (2) injection advance angle increases or decreases the lag according to whether density, temperature, or turbulence has the controlling influence; (3) increase in valve-opening pressure slightly increases the lag; and (4) increase of inlet-air pressure, compression ratio, and engine speed reduces the lag.

Gerrish, Harold C↗
DOE OSTI2022

OptZConfig: Efficient Parallel Optimization of Lossy Compression Configuration

Lossless compressors have very low compression ratios that do not meet the needs of today's large-scale scientific applications that produce vast volumes of data. Error-bounded lossy compression (EBLC) is considered a critical technique for the success of scientific research. Although EBLC allows users to set an error bound for the compression, users have been unable to specify the requirements on the compression quality, limiting practical use. Our contributions are: (1) We formulate the problem of configuring EBLC to preserve a user-defined metric as an optimization problem. This allows many classes of new metrics to be preserved, which improves over current practices. (2) We present a framework, OptZConfig, that can adapt to improvements in the search algorithm, compressor, and metrics with minimal changes, enabling future advancements in this area. (3) We demonstrate the advantages of our approach against the leading methods to configure compressors to preserve specific metrics. Here, our approach improves compression ratios against a specialized compressor by up to 3 x, has a 56x speedup over FRaZ, 1000x speedup over MGARD-QOI post tuning, and 110x speedup over systematic approaches which had not been bounded by compressors before.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1990

Design of QMF (Quadrature Mirror Filter) in spatial domain and edge encoding

Simoncelli and Adelson have extended the one dimensional Quadrature Mirror Filter (QMF) to two dimensions with hexagon symmetry and three dimensional spatio-temporal extensions with rhombic-duodecahedray symmetry. Jain and Crochiere presented an excellent QMF design technique in the time domain. It is proposed to extend the design of a two dimensional QMF over a rectangular lattice in the spatial domain based primarily on the extension of the idea of Jain and Crochiere. In addition, the design will investigate the use of two dimensional Z-transformations. Since this proposed QMF is intended for the applications in image processing, all the important and interesting engineering issues will be addressed throughout the development phase. The design of a two dimensional QMF is discussed. The motivation is to achieve an extremely high data compression ratio. It is entirely possible to achieve dramatic results when pattern recognition techniques are employed. The final goal is the demonstration of extremely high data compression ratios using NASA pictures.

Wang, Paul P.↗
DOE OSTI2021

Performance Comparison of LPG and Gasoline in an Engine Configured for EGR-Loop Catalytic Reforming

In prior work, the EGR loop catalytic reforming strategy developed by ORNL has been shown to provide a relative brake engine efficiency increase of more than 6% by minimizing the thermodynamic expense of the reforming processes, and in some cases achieving thermochemical recuperation (TCR), a form of waste heat recovery where waste heat is converted to usable chemical energy. In doing so, the EGR dilution limit was extended beyond 35% under stoichiometric conditions. In this investigation, a Microlith®-based metal-supported reforming catalyst (developed by Precision Combustion, Inc. (PCI)) was used to reform the parent fuel in a thermodynamically efficient manner into products rich in H2 and CO. We were able to expand the speed and load ranges relative to previous investigations: from 1,500 to 2,500 rpm, and from 2 to 14 bar break mean effective pressure (BMEP). Experiments were conducted to determine the effects of the H/C ratio of the fuel on H2 production and on the engine efficiency in order to compare E10 gasoline (H/C = 1.95) and liquified petroleum gas (LPG), comprised primarily of propane (H/C = 2.67). Additionally, the compression ratio of the engine was increased to ascertain whether further efficiency improvements could be realized based on a reduced knock propensity of the dilute EGR mixture with the reformed fuel. Both the gasoline and propane reforming strategies provided efficiency gains up to 1.85 percentage points and further efficiency improvements with the increased compression ratio were realized. The fuel specific effects of gasoline vs. LPG, the effect of engine operating condition on reforming, and knock limits of the reformed mixture are discussed in detail.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS2013

Effects of Tunable Data Compression on Geophysical Products Retrieved from Surface Radar Observations with Applications to Spaceborne Meteorological Radars

This paper presents results and analyses of applying an international space data compression standard to weather radar measurements that can easily span 8 orders of magnitude and typically require a large storage capacity as well as significant bandwidth for transmission. By varying the degree of the data compression, we analyzed the non-linear response of models that relate measured radar reflectivity and/or Doppler spectra to the moments and properties of the particle size distribution characterizing clouds and precipitation. Preliminary results for the meteorologically important phenomena of clouds and light rain indicate that for a 0.5 dB calibration uncertainty, typical for the ground-based pulsed-Doppler 94 GHz (or 3.2 mm, W-band) weather radar used as a proxy for spaceborne radar in this study, a lossless compression ratio of only 1.2 is achievable. However, further analyses of the non-linear response of various models of rainfall rate, liquid water content and median volume diameter show that a lossy data compression ratio exceeding 15 is realizable. The exploratory analyses presented are relevant to future satellite missions, where the transmission bandwidth is premium and storage requirements of vast volumes of data, potentially problematic.

cloud properties↗
DOE OSTI2022

Optimizing Error-Bounded Lossy Compression for Scientific Data With Diverse Constraints

Vast volumes of data are produced by today's scientific simulations and advanced instruments. These data cannot be stored and transferred efficiently because of limited I/O bandwidth, network speed, and storage capacity. Error-bounded lossy compression can be an effective method for addressing these issues: not only can it significantly reduce data size, but it can also control the data distortion based on user-defined error bounds. In practice, many scientific applications have specific requirements or constraints for lossy compression, in order to guarantee that the reconstructed data are valid for post hoc analysis. For example, some datasets contain irrelevant data that should be isolated in particular and users often have intuition regarding value ranges, geospatial regions, and other data subsets that are crucial for subsequent analysis. Existing state-of-the-art error-bounded lossy compressors, however, do not consider these constraints during compression, resulting in inferior compression ratios with respect to user's post hoc analysis, due to the fact that the data itself provides little or no value for post hoc analysis. In this work we address this issue by proposing an optimized framework that can preserve diverse constraints during the error-bounded lossy compression, e.g., cleaning the irrelevant data, efficiently preserving different precision for multiple value intervals, and allowing users to set diverse precision over both regular and irregular regions. We perform our evaluation on a supercomputer with up to 2,100 cores. Experiments with six real-world applications show that our proposed diverse constraints based error-bounded lossy compressor can obtain a higher visual quality or data fidelity on reconstructed data with the same or even higher compression ratios compared with the traditional state-of-the-art compressor SZ. Furthermore, our experiments also demonstrate very good scalability in compression performance compared with the I/O throughput of the parallel file system.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1989

Toward an image compression algorithm for the high-resolution electronic still camera

Taking pictures with a camera that uses a digital recording medium instead of film has the advantage of recording and transmitting images without the use of a darkroom or a courier. However, high-resolution images contain an enormous amount of information and strain data-storage systems. Image compression will allow multiple images to be stored in the High-Resolution Electronic Still Camera. The camera is under development at Johnson Space Center. Fidelity of the reproduced image and compression speed are of tantamount importance. Lossless compression algorithms are fast and faithfully reproduce the image, but their compression ratios will be unacceptably low due to noise in the front end of the camera. Future efforts will include exploring methods that will reduce the noise in the image and increase the compression ratio.

Nerheim, Rosalee↗
DOE OSTI2021

End-gas autoignition fraction and flame propagation rate in laser-ignited primary reference fuel mixtures at elevated temperature and pressure

Knock in spark-ignited (SI) engines is initiated by autoignition of the unburned gasses upstream of spark-ignited, propagating, turbulent premixed flames. Knock propensity of fuel/air mixtures is typically quantified using research octane number (RON), motor octane number (MON), or methane number (MN; for gaseous fuels), which are measured using single-cylinder, variable compression ratio engines. In this study, knock propensity of SI fuels was quantified via observations of end-gas autoignition (EGAI) in unburned gasses upstream of laser-ignited, premixed flames at elevated pressures and temperatures in a rapid compression machine. Stoichiometric primary reference fuel (PRF; n-heptane/isooctane) blends of varying reactivity (50 ≤ PRF ≤ 100) were ignited using an Nd:YAG laser over a range of temperatures and pressures, all in excess of 545 K and 16.1 bar. Laser ignition produced outwardly-propagating premixed flames. High-speed pressure measurements and schlieren images indicated the presence of EGAI. The fraction of the total heat release attributed to EGAI (i.e., EGAI fraction) varied with fuel reactivity (i.e., octane number) and the time-integrated temperature of the end-gas prior to ignition. Flame propagation rates, which were measured using schlieren images, were only weakly correlated with octane number but were affected by turbulence caused by variation in piston timing. Under conditions of low turbulence, measured flame propagation rates approached one-dimensional premixed laminar flame speed computations performed at the same conditions. Experiments were simulated with a three-dimensional CONVERGE™ model using reduced chemical kinetics (121 species, 538 reactions). The simulations accurately captured the measured flame propagation rates, as well as the variation in EGAI fraction with fuel reactivity and time-integrated end-gas temperature. The simulations also revealed low-temperature heat release as well as formaldehyde and hydrogen peroxide formation in the end-gas upstream of the propagating flame, which increased the temperature and degree of chain branching in the end-gas, ultimately leading to EGAI.

42 ENGINEERING↗
DOE OSTI2021

First-principles equation of state database for warm dense matter computation

We put together a first-principles equation of state (FPEOS) database for matter at extreme conditions by combining results from path integral Monte Carlo and density functional molecular dynamics simulations of the elements H, He, B, C, N, O, Ne, Na, Mg, Al, and Si as well as the compounds LiF , B 4 C , BN , CH 4 , CH 2 , C 2 H 3 , CH , C 2 H , MgO , and MgSiO 3 . For all these materials, we provide the pressure and internal energy over a density-temperature range from ~ 0.5 to 50 g cm - 3 and from ~ 10 4 to 10 9 K, which are based on ~ 5000 different first-principles simulations. We compute isobars, adiabats, and shock Hugoniot curves in the regime of L - and K -shell ionization. Invoking the linear mixing approximation, we study the properties of mixtures at high density and temperature. Furthermore, we derive the Hugoniot curves for water and alumina as well as for carbon-oxygen, helium-neon, and CH-silicon mixtures. We predict the maximal shock compression ratios of H 2 O , H 2 O 2 , Al 2 O 3 , CO , and CO 2 to be 4.61, 4.64, 4.64, 4.89, and 4.83, respectively. Finally we use the FPEOS database to determine the points of maximum shock compression for all available binary mixtures. We identify mixtures that reach higher shock compression ratios than their end members. We discuss trends common to all mixtures in pressure-temperature and particle-shock velocity spaces. In the Supplemental Material, we provide all FPEOS tables as well as computer codes for interpolation, Hugoniot calculations, and plots of various thermodynamic functions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Modeling the impact of the fuel injection strategy on the combustion and performance characteristics of a heavy-duty GCI engine

Gasoline compression ignition (GCI) is a promising strategy to achieve high thermal efficiency and low emissions with limited modifications to the conventional diesel engine hardware. It is a partially premixed concept, which derives its superiority from higher volatility and longer ignition delay of gasoline-like fuels combined with higher compression ratio typical of diesel engines. Here, the present study investigates the combustion process in a GCI engine operating with different injection strategies using computational fluid dynamics (CFD). Simulations are carried out on a single cylinder of a multi cylinder heavy-duty compression ignition engine, which operates at a compression ratio of 17:1 and an engine speed of 1038 rev/min. Two different injection strategies viz., late injection (LI), and early pilot injection (EP) are investigated to understand their impact on combustion and performance of the engine. Renormalized group (RNG) k-ε model is used to describe in-cylinder turbulence and KH RT model is used to simulate the fuel spray breakup. The developed CFD methodology is validated against relevant experimental data under a wide range of operating conditions for each injection strategy. The developed CFD methodology was found to capture the engine combustion behavior quite well. Based on the validated CFD model, the differences in the progress of combustion event for the two injection strategies is highlighted. It was found that a larger pilot fuel mass fraction results in a steeper rise in the initial heat release rate which in turn influences the transition to mixing controlled combustion. In line with the experimental data, the study showed that the late pilot injection strategy with three injection pulses, results in higher performance compared to the other conditions.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

EGR Dilution and Fuel Property Effects on High-Efficiency Spark-Ignition Flames

Modern spark ignition internal combustion engines rely on fast combustion rates and high dilution to achieve high brake thermal efficiencies. To accomplish this, new engine designs have moved towards increased tumble ratios and stroke-to-bore ratios. Increased tumble ratios correlate positively with increases in turbulent kinetic energy and improved fuel and residual gas mixing, all of which favor faster and more efficient combustion. Longer stroke-to-bore ratios allow higher geometric compression ratios and use of late intake valve closing to control peak compression pressures and temperatures. The addition of dilution to improve efficiency is limited by the resulting increase in combustion instabilities manifested by cycle-to-cycle variability. A number of effects - preferential diffusion, turbulence-combustion interactions, stochastic flow patterns, laminar-turbulent flame kernel transitions, and relative length and velocity scales between flame and turbulence - are believed to be responsible for the increase in cycle-to-cycle variations, where their contributions are likely interlinked. Several studies have shown the influence of stochastic flow characteristics on the nature of combustion instabilities, such as velocity patterns on flame kernel formation and cycle-to-cycle variations in residual gas. However, few have focused on the specific effects of fuel properties. The objective of this work is to contrast the effects of dilution on propane stoichiometric combustion against gasoline. Dilution tolerance experiments were conducted in a purpose-built high stroke-to-bore ratio single cylinder engine with both gasoline and LPG. Three-dimensional full cycle computational fluid dynamics (CFD) simulations employing a level-set combustion approach and Reynolds averaged Navier-Stokes (RANS) turbulence modeling was used to qualitatively assess the changes in length and velocity scales for turbulence and the flame. The experimental results showed that LPG can tolerate higher exhaust gas recirculation (EGR) dilution under a variety of conditions. Analysis of CFD simulations showed that propane flames are likely less sensitive to influences from the flow field due to less thickening of the flame and higher effective flame speeds.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1983

Monte Carlo simulation of steady state shock structure including cosmic ray mediation and particle escape

Both hydrodynamic calculations (Drury and Volk, 1981, and Axford et al., 1982) and kinetic simulations imply the existence of thermal subshocks in high-Mach-number cosmic-ray-mediated shocks. The injection efficiency of particles from the thermal background into the diffusive shock-acceleration process is determined in part by the sharpness and compression ratio of these subshocks. Results are reported for a Monte Carlo simulation that includes both the back reaction of accelerated particles on the inflowing plasma, producing a smoothing of the shock transition, and the free escape of particles allowing arbitrarily large overall compression ratios in high-Mach-number steady-state shocks. Energy spectra and estimates of the proportion of thermal ions accelerated to high energy are obtained.

Ellison, D. C.↗
DOE OSTI2025

Real Time implementation of Artificial Intelligence compression algorithm for High-Speed Streaming Readout signals

The new generation of high-energy physics experiments plans to acquire data in streaming mode. With this approach, it is possible to access the information of the whole detector (organized in time slices) for optimal and lossless triggering of data acquisitions. With this approach, data rates, especially in large detectors, are often very high, and the network is likely to be the bottleneck for the entire Streaming Read Out system. The aim of this work is to study the implementation of a lossy compression algorithm based on Artificial Intelligence: an Autoencoder. With Machine Learning it is possible to achieve a high compression ratio and fast inference time with only a small degradation of the signals, almost negligible for the specific application. This work explores different configurations of the Autoencoder and the implementation on different hardware. Different Autoencoder configurations are explored to find the best trade-off between compression ratio and reconstruction loss, both for signals and energy spectrum. Different hardware implementations are also explored to find the best platform to achieve real-time performance for the specific application.

Rossi, Fabio (ORCID:0009000385713885)↗
NASA NTRS1927

Description of the NACA Universal Test Engine and Some Test Results

This report describes the 5-inch bore by 7-inch stroke single cylinder test engine used at the Langley Field Laboratory of the National Advisory Committee for Aeronautics in laboratory research on internal-combustion engine problems and presents some results of tests made therewith. The engine is arranged for variation over wide ranges, of the compression ratio and lift and timing of both inlet and exhaust valves while the engine is in operation. Provision is also made for the connection of a number of auxiliaries. These features tend to make the engine universal in character, and especially suited for the study of certain problems involving change in compression ratio, valve timing, and lift.

Ware, Marsden↗
NASA NTRS2000

Effects of Digitization and JPEG Compression on Land Cover Classification Using Astronaut-Acquired Orbital Photographs

Studies that utilize astronaut-acquired orbital photographs for visual or digital classification require high-quality data to ensure accuracy. The majority of images available must be digitized from film and electronically transferred to scientific users. This study examined the effect of scanning spatial resolution (1200, 2400 pixels per inch [21.2 and 10.6 microns/pixel]), scanning density range option (Auto, Full) and compression ratio (non-lossy [TIFF], and lossy JPEG 10:1, 46:1, 83:1) on digital classification results of an orbital photograph from the NASA - Johnson Space Center archive. Qualitative results suggested that 1200 ppi was acceptable for visual interpretive uses for major land cover types. Moreover, Auto scanning density range was superior to Full density range. Quantitative assessment of the processing steps indicated that, while 2400 ppi scanning spatial resolution resulted in more classified polygons as well as a substantially greater proportion of polygons < 0.2 ha, overall agreement between 1200 ppi and 2400 ppi was quite high. JPEG compression up to approximately 46:1 also did not appear to have a major impact on quantitative classification characteristics. We conclude that both 1200 and 2400 ppi scanning resolutions are acceptable options for this level of land cover classification, as well as a compression ratio at or below approximately 46:1. Auto range density should always be used during scanning because it acquires more of the information from the film. The particular combination of scanning spatial resolution and compression level will require a case-by-case decision and will depend upon memory capabilities, analytical objectives and the spatial properties of the objects in the image.

Robinson, Julie A.↗
NASA NTRS1940

Correlation of knocking characteristics of fuels in an engine having a hemispherical combustion chamber

Data are presented to show the effects of inlet-air pressure, inlet-air temperature, and compression ratio on the maximum permissible performance obtained with having a hemispherical-dome combustion chamber. The five aircraft-engine fuels used have octane numbers varying from 90 to 100 plus 2 ml of tetraethyl lead per gallon. The data were obtained on a 5 1/4-inch by 4 3/4-inch liquid-cooled engine operating at 2,500 r.p.m. The compression ratio was varied from 6.0 to 8.9. The inlet-air temperature was varied from 110 to 310 F. For each set of conditions, the inlet-air pressure was increased until audible knock occurred and then reduced 2 inches of mercury before data were recorded. The results for each fuel can be correlated by plotting the calculated end-gas density factor against the calculated end-gas temperature. Measurements of spark-plugs, cutting off the switch to one spark plug lowered the electrode temperature of that plug from a value of 1,365 F to a value of 957 F. The results indicate that the surface temperatures of combustion-chamber areas which become new sources of ignition markedly increase after ignition.

Rothrock, A M↗