Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONTROL STICKS - FORCES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

A Generic T-Tail Transport Airplane Simulation for High-Angle-Of-Attack Dynamics Modeling Investigations

A preliminary simulation of a generic T-tail transport airplane configuration has been developed at the National Aeronautics and Space Administration Langley Research Center. The primary purpose of this piloted simulation is to assess aerodynamic model fidelity requirements for training airline pilots to recognize and recover from full-stall flight conditions in a T-tail airplane. As a result, significant flexibility has been designed into the flight dynamics model. The flight dynamics model is based on newly acquired static and dynamic stability and control data from sources that include: wind tunnel, water tunnel, and computational fluid dynamics. Preliminary results for initial stall show an unstable stall pitch break (if the stick pusher is inhibited), un-commanded motions due to stall asymmetries, significantly reduced dynamic roll stability, and decreased control effectiveness. Preliminary studies indicated an insensitivity to the fidelity of the pitch damping model.

Cunningham, Kevin↗

An analysis of the effects of aeroelasticity on static longitudinal stability and control of a swept-back-wing airplane

A theoretical analysis of the effects of aeroelasticity on the stick-fixed static longitudinal stability and elevator angle required for balance of an airplane is presented together with calculated effects for a swept-wing bomber of relatively high flexibility. Although large changes in stability due to certain parameters are indicated for the example airplane, the over-all stability change after considering all parameters was quite small, compared to the individual effects, due to the counterbalancing of wing and tail contributions. The effect of flexibility on longitudinal control for the example airplane was found to be of little real importance.

STABILITY, LONGITUDINAL - STATIC↗

Characterization of Pilot Technique

Skilled pilots often use pulse control when controlling higher order (i.e. acceleration-command) vehicle dynamics. Pulsing does not produce a stick response that resembles what the human Crossover Model predicts. The Crossover Model (CM) assumes the pilot provides compensation necessary (lead or lag) such that the suite of display-human-vehicle approximates an integrator in the region of crossover frequency. However, it is shown that the CM does appear to drive the pilots pulsing behavior in a very predictable manner. Roughly speaking, the pilot generates pulses such that the area under the pulse (pulse amplitude multiplied by pulse width) is approximately equal to area under the hypothetical CM output. This can allow a pilot to employ constant amplitude pulsing so that only the pulse duration (width) is modulated a drastic simplification over the demands of continuous tracking. A pilot pulse model is developed, with which the parameters of the pilots internally-generated CM can be computed in real time for pilot monitoring and display compensation. It is also demonstrated that pursuit tracking may be activated when pulse control is employed.

rotorcraft↗

The influence of a prediction display on the quasi-linear describing function and remnant measured with an adaptive analog-pilot in a closed loop

The effect of a prediction display on the human transfer characteristics is explained with the aid of a quasi-linear model. The prediction display causes an increase of the gain factor and the lead factor, a diminishing of the lag factor and a decrease of the remnant. Altogether, these factors yield a smaller mean square value of the control deviation and a simultaneous decrease of the mean square value of the stick signal.

Dey, D.↗

Pilot opinions of sampling effects in lateral-directional control

Flight experiments with a microprocessor control system were conducted to determine the effects of variations in sampling parameters on several pilots' opinions of lateral-directional flying qualities. Princeton's variable-response research aircraft (VRA), which is equipped with a microprocessor based digital flight control system (Micro-DFCS), was the test vehicle. Two U.S. Navy pilots evaluated the effects of sampling rate, quantization, and pure time delay during tracking, approach, and landing. Aircraft carrier approach tasks were conducted using a Navy approach mirror. Acquisition and tracking of fixed objects on the ground provided additional information related to the Navy misson. The longitudinal controls were implemented with analog electronics, while the lateral-directional pilot inputs (stick and rudder) were fed to the Micro-DFCS, which commanded the ailerons and rudder. The conceptual relationship between the evaluation pilot's lateral-directional inputs, the flight computer, and the aircraft are illustrated.

Stengel, R. F.↗

Space Suit Portable Life Support System Thermal Control Valve Ball Design

A Thermal Control Valve (TCV) has been in development for the Exploration Extravehicular Mobility Unit Portable Life Support System (xEMU PLSS). The xEMU PLSS TCV controls flow going to the liquid cooling and ventilation garment that the crew member wears during extra-vehicular activity to expel waste heat. A previous TCV version with a linear actuator and diverter valve has been tested to attempt to control the flow accurately. The previous valve has a non-linear flow response relative to valve position and has struggled to meet the setpoints desired for precise thermal control. While many diverter valve design variations have been attempted, all previous designs have had difficulty meeting set points. Additionally, high precision machining is required to create a metal-on-metal seal which has its own drawbacks and does not always meet requirements for internal leakage. This metal seal also requires stalling a linear actuator to load the seal in compression or tension which has caused sticking failures when stalled. A new approach and design for a TCV has been developed which uses a rotational ball to control flow and has demonstrated a much more precise and linear flow control. The design functions like a two-way ball valve with two Teflon seats that cradle and compress the ball for sealing. The ball outlet has a unique geometric design to create a set-able orifice like hole which is more predictable at controlling flow. Additionally, the Teflon seat performs much better for preventing internal leakage than the metal seal and prevents sticking by having a large range in which it is sealed without having to stall the actuator. This paper will review a new proposed xEMU PLSS TCV ball design and compare it with previous iterations of the design.

Ryan Ogilvie↗

Space Suit Portable Life Support System Thermal Control Valve Ball Design

A Thermal Control Valve (TCV) has been in development for the Exploration Extravehicular Mobility Unit Portable Life Support System (xEMU PLSS). The xEMU PLSS TCV controls flow going to the liquid cooling and ventilation garment that the crew member wears during extra-vehicular activity to expel waste heat. A previous TCV version with a linear actuator and diverter valve has been tested to attempt to control the flow accurately. The previous valve has a non-linear flow response relative to valve position and has struggled to meet the setpoints desired for precise thermal control. While many diverter valve design variations have been attempted, all previous designs have had difficulty meeting set points. Additionally, high precision machining is required to create a metal-on-metal seal which has its own drawbacks and does not always meet requirements for internal leakage. This metal seal also requires stalling a linear actuator to load the seal in compression or tension which has caused sticking failures when stalled. A new approach and design for a TCV has been developed which uses a rotational ball to control flow and has demonstrated a much more precise and linear flow control. The design functions like a two-way ball valve with two Teflon seats that cradle and compress the ball for sealing. The ball outlet has a unique geometric design to create a set-able orifice like hole which is more predictable at controlling flow. Additionally, the Teflon seat performs much better for preventing internal leakage than the metal seal and prevents sticking by having a large range in which it is sealed without having to stall the actuator. This paper will review a new proposed xEMU PLSS TCV ball design and compare it with previous iterations of the design.

Ryan Ogilvie↗

Flexible Wing Base Micro Aerial Vehicles: Assessment of Controllability of Micro Air Vehicles

In the last several years, we have developed unique types of micro air vehicles that utilize flexible structures and extensible covering materials. These MAVs can be operated with maximum dimensions as small as 6 inches and carry reasonable payloads, such as video cameras and transmitters. We recently demonstrated the potential of these vehicles by winning the Fourth International Micro Air Vehicle Competition, held at Ft. Huachucha, Arizona in May 2000. The pilots report that these vehicles have unusually smooth flying characteristics and are relatively easy to fly, both in the standard RC mode and "through the camera" when at greater distances. In comparison, they find that similar sized vehicles with more conventional rigid construction require much more input from the pilot just to maintain control. To make these subjective observations more quantitative, we have devised a system that can conveniently record a complete history of all the RC transmitter stick movements during a flight. Post-flight processing of the stick movement data allows for direct comparisons between different types of MAVs when flown by the same pilot, and also comparisons between pilots. Eventually, practical micro air vehicles will be autonomously controlled, but we feel that the smoothest flying and easiest to fly embodiments will also be the most successful in the long run. Comparisons between several types of micro air vehicles will be presented, along with interpretations of the data.

Jenkins, David A.↗

The Factors that Determine the Minimum Speed of an Airplane

The author argues that because of a general misunderstanding of the principles of flight at low speed, there are a large number of airplanes that could be made to fly several miles per hour slower than at present by making slight modifications. In order to show how greatly the wing section affects the minimum speed, curves are plotted against various loadings. The disposition of wings on the airplane slightly affects the lift coefficient, and a few such cases are discussed. Another factor that has an effect on minimum speed is the extra lift exerted by the slip stream on the wings. Also discussed are procedures to be followed by the pilot, especially with regard to stick movements during low speed flight. Also covered are stalling, yaw, rolling moments, lateral control, and the effectiveness of ailerons and rudders.

AIRPLANES - SPEED AND POWER AIRPLANE - SPEED↗

Variable-Speed Simulation of a Dual-Clutch Gearbox Tiltrotor Driveline

This investigation explores the variable-speed operation and shift response of a prototypical two-speed dual-clutch transmission tiltrotor driveline in forward flight. Here, a Comprehensive Variable-Speed Rotorcraft Propulsion System Modeling (CVSRPM) tool developed under a NASA funded NRA program is utilized to simulate the drive system dynamics. In this study, a sequential shifting control strategy is analyzed under a steady forward cruise condition. This investigation attempts to build upon previous variable-speed rotorcraft propulsion studies by 1) including a fully nonlinear transient gas-turbine engine model, 2) including clutch stick-slip friction effects, 3) including shaft flexibility, 4) incorporating a basic flight dynamics model to account for interactions with the flight control system. Through exploring the interactions between the various subsystems, this analysis provides important insights into the continuing development of variable-speed rotorcraft propulsion systems.

DeSmidt, Hans↗

Neural Flight Control System

The Neural Flight Control System (NFCS) was developed to address the need for control systems that can be produced and tested at lower cost, easily adapted to prototype vehicles and for flight systems that can accommodate damaged control surfaces or changes to aircraft stability and control characteristics resulting from failures or accidents. NFCS utilizes on a neural network-based flight control algorithm which automatically compensates for a broad spectrum of unanticipated damage or failures of an aircraft in flight. Pilot stick and rudder pedal inputs are fed into a reference model which produces pitch, roll and yaw rate commands. The reference model frequencies and gains can be set to provide handling quality characteristics suitable for the aircraft of interest. The rate commands are used in conjunction with estimates of the aircraft s stability and control (S&C) derivatives by a simplified Dynamic Inverse controller to produce virtual elevator, aileron and rudder commands. These virtual surface deflection commands are optimally distributed across the aircraft s available control surfaces using linear programming theory. Sensor data is compared with the reference model rate commands to produce an error signal. A Proportional/Integral (PI) error controller "winds up" on the error signal and adds an augmented command to the reference model output with the effect of zeroing the error signal. In order to provide more consistent handling qualities for the pilot, neural networks learn the behavior of the error controller and add in the augmented command before the integrator winds up. In the case of damage sufficient to affect the handling qualities of the aircraft, an Adaptive Critic is utilized to reduce the reference model frequencies and gains to stay within a flyable envelope of the aircraft.

Gundy-Burlet, Karen↗

Factors affecting the sticking of insects on modified aircraft wings

Past studies have shown that the surface energy of a polymer coating has an important effect on the sticking of insects to the surface. However, mechanical properties of polymer coatings such as elasticity may also be important. A further study is suggested using polymer coatings of known surface energy and modulus so that a better understanding of the mechanism of the sticking of insects to surfaces can be achieved. As the first step for the study, surface analysis and road tests were performed using elastomers having different energies and different moduli. The number of insects sticking to each elastomer was counted and compared from sample to sample and with a control (aluminum). An average height moment was also calculated and comparisons made between samples.

Yi, O.↗

A psychologist's view of validating aviation systems

All systems, no matter what they are designed to do, have shortcomings that may make them less productive than was hoped during the initial development. Such shortcomings can arise at any stage of development: from conception to the end of the implementation life cycle. While systems failure and errors of a lesser magnitude can occur as a function of mechanical or software breakdown, the majority of such problems, in aviation are usually laid on the shoulders of the human operator and, to a lesser extent, on human factors. The operator bears the responsibility and blame even though, from a human factors perspective, error may have been designed into the system. Human factors is not a new concept in aviation. The name may be new, but the issues related to operators in the loop date back to the industrial revolution of the nineteenth century and certainly to the aviation build-up for World War I. During this first global confrontation, military services from all sides discovered rather quickly that poor selection and training led to drastically increased personnel losses. While hardware design became an issue later, the early efforts were primarily focused on increased care in pilot selection and on their training. This actually involved early labor-intensive simulation, using such devices as sticks and chairs mounted on rope networks which could be manually moved in response to control input. The use of selection criteria and improved training led to more viable person-machine systems. More pilots survived training and their first ten missions in the air, a rule of thumb arrived at by experience which predicted ultimate survival better than any other. This rule was to hold through World War II. At that time, personnel selection and training became very sophisticated based on previous standards. Also, many psychologists were drafted into Army Air Corps programs which were geared towards refining the human factor. However, despite the talent involved in these programs and the tremendous build-up of aviation during the war, there were still aircraft designs that were man killers (no sexism implied since all combat pilots were men). One classic design error that was identified fifty years ago was the multipointer altimeter, which could easily be misread especially by a pilot under considerable task load. It has led to flying fully operational aircraft into the terrain. The authors of the research which formally identified this problem put 'Human Errors' in quotes to express their dissatisfaction with the traditional approach to accident investigation. It traditionally places the burden of guilt on the operator. Some of these altimeters still exist in older aircraft to this day.

Stein, Earl S.↗

X-31 flight test update

The goals of the tactical utility flight test are to verify the basic tactical lessons learned in simulation and determine the situational awareness implications of post-stall maneuvering. Tactics and lessons learned from post-stall engagements will supplement current fighter tactics and complement future fighter tactics development. Although the present envelope of the X-31 for carefree post stall (PST) use is limited to 225 KIAS versus 325 KIAS in simulations, the same initial conditions used in 'Pinball II' are being utilized in flight test. Starting conditions up to 325 KIAS are being flown during the build-up phase leading to the full close in air combat (CIC) evaluations. The flight control program has been modified to limit PST entry to below 225 KIAS. Full aft stick application above 225 KIAS cannot command angle of attack (AOA) in excess of 30 deg.

Groves, AL↗

Supplementary Investigation in the Langley Free-Spinning Tunnel of a 1/20-Scale Model of the Douglas XF4D-1 Airplane Including Spin-Recovery Parachute Tests of the Model Loaded to Simulate the Douglas F5D-1 Airplane

A supplementary investigation has been conducted in the Langley 20-foot free-spinning tunnel of a l/20-scale model of the Douglas XF4D-1 airplane to determine the effect of only neutralizing the rudder for recovery from an inverted spin, and the effect of partial aileron deflection with the spin for recovery from an erect spin. An estimation of the size parachute required for satisfactory recovery from a spin with the model ballasted to represent the Douglas F5D-1 (formerly the Douglas XF4D-2) airplane was also made. Results of the original investigation on the XF4D-1 design are presented in NACA RM SL50K30a. The results indicated that satisfactory recoveries from inverted spins of the airplane should be obtained by rudder neutralization when the longitudinal stick position is neutral or forward. Recoveries from erect spins from the normal-spin control configuration should be satisfactory by full rudder reversal with simultaneous movement of the ailerons to two-thirds with the spin. For the parachute tests with the model loaded to represent the F5D-1 airplane, the tests indicated that a 16.7-foot-diameter hemispherical-tail parachute (drag coefficient of 1.082 based on the projected area) with a towline 20.0 feet long (full- scale values) should be satisfactory for an emergency spin-recovery device during demonstration spins of the airplane.

Klinar, Walter J.↗

Space Suit Portable Life Support System Thermal Control Valve Ball Design

A Thermal Control Valve (TCV) has been in development for the Exploration Extravehicular Mobility Unit Portable Life Support System (xEMU PLSS). The xEMU PLSS TCV controls flow going to the liquid cooling and ventilation garment that the crew member wears during extra-vehicular activity to expel waste heat. A pervious TCV version with a linear actuator and diverter valve has been tested extensively to attempt to control the flow accurately. The previous TCV diverter valve has a non-linear flow response relative to valve position and has struggled to accurately meet the setpoints desired for precision thermal control. While many diverter valve design variations have been attempted, previous designs have all had difficulty in meeting set points. Additionally, high precision machining is required for these diverter valves to create a metal-on-metal seal which has its own drawbacks and doesn’t always meet requirements for internal leakage. This metal compression seal also requires stalling the linear actuator to load the seal in compression or tension which has demonstrated valve sticking failures when stalled. The xEMU PLSS TCV implements a new approach and design for a TCV which uses a rotational ball to control flow and has demonstrated a much more precise and linear flow control. The design functions like a two-way ball valve with two Teflon seats that cradle and compress the ball for sealing. A new geometric design modification to the ball outlet can create a set-able orifice like hole which is more predictable at controlling flow than using an annulus with the previous diverter valve. Additionally, the Teflon seat performs much better for preventing internal leakage than the metal seal and prevents sticking by having a large range in which it is sealed without having to stall the actuator. This paper will review a new proposed xEMU PLSS TCV ball design and compare it with previous iterations of the design.

Ryan Ogilvie↗

Evaluation of HiMAT aircraft landing approach lateral control gearing using simulation and a visual display

The utility of a visual display when studying the influence of changes in lateral stick gearing gains on the Highly Maneuverable Aircraft Technology (HiMAT) vehicle handling qualities during simulated approaches and landings is investigated. The visual display improved the validity of the simulation and provided improved roll response cues for the HiMAT aircraft landing approach. A range of acceptable constant lateral stick gearing gains is found that provides adequate maneuverability and allows for precision moments.

Sarrafian, S. K.↗

A study of simplified methods for longitudinal control decoupling

Using an inflight simulator, a simple longitudinal decoupling concept was compared with conventional airplane characteristics for the approach and landing tasks. The decoupling system allowed the pilot to command flight path angle changes with the stick with little or no accompanying speed change; likewise, speed changes with only small accompanying flight path changes could be made with throttle only. The unique feature of the concept is that it is an open loop (that is, nonfeedback) control system. Results indicate that in calm air and up to moderate levels of turbulence the decoupling system provides a substantial reduction in pilot workload.

Joslin, R.↗