Search NASA⌕ Search

SEARCH · Search NASA

Results for “CRITICAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

The Mechanical Properties of a Ni-30Al-20Fe-0.05Zr Intermetallic Alloy in the Temperature Range 300-1200 K

Tensile tests were conducted on an extruded Ni-30(at. pct)Al-20Fe-0.05Zr intermetallic alloy in the temperature range 300-1200 K, and the microstructures were characterized by optical, scanning, and transmission electron microscopy. The alloy did not exhibit any room temperature ductility and failed by transgranular cleavage at a stress of about 710 MPa. This mode of fracture was observed at and below 873 K with the total ductility being less than 2.5 percent. However, the failure mode changed to dimpled fracture, triple point cracking, and rupture above 873 K. Scanning electron microscopy of the fracture surfaces revealed that transgranular cleavage failure had always originated at preexisting defects. In these cases, the fracture stress exhibited a good correlation with the defect size, in accordance with linear elastic fracture mechanics, where the critical stress intensity factor was estimated to be about 4 MPa sq rt m.

Raj, S. V.↗
DOE OSTI2024

The Effect of Normal Stress Oscillations on Fault Slip Behavior Near the Stability Transition From Stable to Unstable Motion

Tectonic fault zones are subject to normal stress variations with a wide range of spatio-temporal scales. Stress perturbations cover a wide range of frequencies and amplitudes from high frequency seismic waves generated by earthquakes to low frequency transients associated with solid Earth tides. These perturbations can reactivate critically stressed faults and trigger earthquakes. Here, we describe lab experiments to illuminate the physics of such changes in friction and the mechanics of earthquake triggering and fault reactivation. Friction tests were done in a double direct shear configuration for conditions near the stability transition from stable to unstable motion. We studied simulated fault gouge composed of quartz powder and conducted experiments at reference normal stress from 10 to 13.5 MPa. After shearing to steady state sliding, we applied sinusoidal normal stress oscillations of amplitude 0.5–2 MPa, and period of 0.5–50 s. We performed numerical simulations using measured values of rate and state friction (RSF) parameters to assess our data. Our results show that low frequency stress oscillations cause a Coulomb-like response of shear strength that transitions from stable slip to slow lab earthquakes as frequency increases. At the critical frequency predicted by RSF we observe periodic stick-slip behavior. Perturbations of high amplitude and short period weaken the fault, while lower amplitudes strengthen the fault. We find that a modified RSF formulation is able to accurately match our laboratory data. Our findings highlight the complex effects of stress perturbations on fault strength and the mode of fault slip.

58 GEOSCIENCES↗
NASA NTRS1940

The Lateral Stability of Equal-flanged Aluminum-alloy I-beams Subjected to Pure Bending

Equal-flange beams of a special extruded I-section of 27ST aluminum alloy were tested in pure bending. Complete end fixity was not attained. Loading was continued until a definite maximum value had been reached. Tensile tests were made on specimens cut from the flanges and the web of each beam. Compressive stress-strain characteristics were determined by pack compression tests on specimens cut from the flanges. Values computed from an equation previously suggested by one of the authors for the critical stress at which such beams become unstable were found to be in good agreement with values computed from experimentally determined critically bending moments.

Dumont, C↗
DOE OSTI2023

Multiscale modeling for high burnup structure formation and associated pulverization

This report summarizes the lower length scale modeling work performed in the fiscal year 2023 under the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program to capture the microstrutural evolution and associated pulverization criteria in the high burnup regions. This year, the resolution mechanisms within the cluster dynamics code has been updated and it influence on the bubble growth in HBS regions at the mesoscale is studied. To improve the accuracy of phase-field models of fission gas bubble growth, a new Helmholtz free energy for high-density Xe gas is derived from a virial equation of state. Two previously used strategies for representing net vacancy production in phase-field models of fission gas bubble growth are compared with each other and with analytical models of bubble growth. The vacancy source only model is found to be more convenient to parameterize realistically compared with the vacancy source+sink model. Furthermore, the phase-field-fracture simulation have been performed using MD- informed failure stress values and realistic HBS structure obtained from the phase-field simulations. We also present the uncertainty bands on prediction of the critical stress to account for the effect of the lower length scale variabilities on the failure criteria at the mesoscale. It is observed that pulverization may occur in partially restructured regions with restructuring fraction as low as 17%. In light of this, an update to the BISON’s pulverization criteria is recommended.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1975

Crack growth in bonded elastic half planes

Two solutions were developed for the two dimensional problem of bonded linearly elastic half-planes. For each solution, numerical results are presented for the stress intensity factors, strain energy release rate, stresses, and displacements. The behavior predicted by the studies was investigated experimentally using polymers for the material pairs. Close agreement was found for the critical stress intensity factor at fracture for the perpendicular crack near the interface. Fracture along the interface proved to be inconclusive due to difficulties in obtaining a brittle bond. Some interesting and predictable behavior regarding the potential for the crack to cross the interface was observed and is discussed.

Goree, J. G.↗
NASA NTRS2011

Fracture in Phenolic Impregnated Carbon Ablator

The thermal protection materials used for spacecraft heat shields are subjected to various thermal-mechanical loads during an atmospheric entry which can threaten the structural integrity of the system. This paper discusses the development of a novel technique to understand the failure mechanisms inside thermal protection materials. The focus of research is Phenolic Impregnated Carbon Ablator (PICA). It has successfully flown on the Stardust spacecraft and is the TPS material chosen for the Mars Science Laboratory (MSL) and Dragon spacecraft. Although PICA has good thermal properties, structurally, it is a weak material. In order to thoroughly understand failure in PICA, fracture tests were performed on FiberForm* (precursor of PICA), virgin and charred PICA materials. Several samples of these materials were tested to investigate failure mechanisms at a microstructural scale. Stress-strain data were obtained simultaneously to estimate the fracture toughness. It was found that cracks initiated and grew in the FiberForm when a critical stress limit was reached such that the carbon fibers separated from the binder. However, both for virgin and charred PICA, crack initiation and growth occurred in the matrix (phenolic) phase. Both virgin and charred PICA showed greater strength values compared to FiberForm coupons, confirming that the presence of the porous matrix helps in absorbing the fracture energy.

Agrawal, Parul↗
NASA NTRS1989

Application of fracture mechanics and half-cycle method to the prediction of fatigue life of B-52 aircraft pylon components

Stress intensity levels at various parts of the NASA B-52 carrier aircraft pylon were examined for the case when the pylon store was the space shuttle solid rocket booster drop test vehicle. Eight critical stress points were selected for the pylon fatigue analysis. Using fracture mechanics and the half-cycle theory (directly or indirectly) for the calculations of fatigue-crack growth ,the remaining fatigue life (number of flights left) was estimated for each critical part. It was found that the two rear hooks had relatively short fatigue life and that the front hook had the shortest fatigue life of all the parts analyzed. The rest of the pylon parts were found to be noncritical because of their extremely long fatigue life associated with the low operational stress levels.

Ko, W. L.↗
NASA NTRS1986

On fracture of fibrous composites

The problem of an existing through-the-thickness center notch in a unidirectional fibrous composite is investigated using a homogeneous anisotropic elasticity analysis in conjunction with various crack growth criteria. Tensor polynomial, strain energy density, and normal stress ratio criteria are applied as crack growth direction criteria and compared to experimental observations. For the cases and criteria studied, only the normal stress ratio criterion exhibits an ability to correctly predict crack growth direction. The normal stress ratio criterion is subsequently applied to the same cases as a failure criterion. Comparison with experiment indicates that these predictions exhibit reasonable correlation with observed critical stresses. Finally, the macroscopic approach to the problem used in this study is compared to a microscopic shear lag analysis of experimental results in the literature. The comparison indicates that both approaches yield essentially identical predictions. The comparisons made with other criteria and approaches indicate that application of the normal stress ratio within a macroscopic level analysis has great potential as an approach to modeling composite crack growth.

Beuth, J. L., Jr.↗
NASA NTRS2013

Fracture in Phenolic Impregnated Carbon Ablator

This paper describes the development of a novel technique to understand the failure mechanisms inside thermal protection materials. The focus of this research is on the class of materials known as phenolic impregnated carbon ablators. It has successfully flown on the Stardust spacecraft and is the thermal protection system material chosen for the Mars Science Laboratory and SpaceX Dragon spacecraft. Although it has good thermal properties, structurally, it is a weak material. To understand failure mechanisms in carbon ablators, fracture tests were performed on FiberForm(Registered TradeMark) (precursor), virgin, and charred ablator materials. Several samples of these materials were tested to investigate failure mechanisms at a microstructural scale. Stress-strain data were obtained simultaneously to estimate the tensile strength and toughness. It was observed that cracks initiated and grew in the FiberForm when a critical stress limit was reached such that the carbon fibers separated from the binder. However, both for virgin and charred carbon ablators, crack initiation and growth occurred in the matrix (phenolic) phase. Both virgin and charred carbon ablators showed greater strength values compared with FiberForm samples, confirming that the presence of the porous matrix helps in absorbing the fracture energy.

Agrawal, Parul↗
NASA NTRS1976

Lattice theory of three-dimensional cracks

The problem of the stability of a three-dimensional crack is analyzed within a lattice-statics approximation. The consequence of introducing a jog into the crack face as well as the effects of various nonlinear-force laws are studied. The phenomenon of lattice trapping (upper and lower bounds on the applied stress for an equilibrium crack of given length) is again obtained. It is possible to obtain some physical insight into which aspects of the force law are critical for crack stability. In particular, the inadequacy of a thermodynamic approach - which relates the critical stress to a surface energy corresponding to the area under the cohesive-force-vs-displacement curve - is demonstrated. Surface energy is a global property of the cohesive-force law. Crack stability is sensitive to much more refined aspects of the cohesive-force law. Crack healing is sensitive to the long-range portion of the cohesive force. Crack expansion is sensitive to the position of the maximum in the cohesive-force relation.

Esterling, D. M.↗
NASA NTRS1939

Experimental and analytical investigation of a monocoque wing model loaded in bending

Bending tests with transverse loads and with pure bending were undertaken on a double-web monocoque wing model in order to establish the relation between the state of stress and the results from the elementary bending theory. The longitudinal stresses in the stiffeners were measured with tensiometers and the shear stresses in the sheet were calculated from them. The measurements were made at both moderate loads with no buckles in the covering and at loads with which the critical stress in the individual panels was exceeded. For the comparison, the wing skin was considered as stiffened sheet according to the shear panel scheme. In this way, the statistically indeterminate calculation was confirmed by the test results.

Schapitz, E↗
DOE OSTI2024

Stress relaxation cracking susceptibility evaluation in 347H stainless steel welds

Abstract Stress relaxation cracking (SRC) has been reported as a dominant failure mechanism for 347H stainless steel welds at elevated service temperatures, occurring in either the heat-affected zone (HAZ) or fusion zone (FZ). In this study, SRC susceptibility of physically simulated HAZ and cross-welded E347-347H stainless steel welds was studied using a four-step accelerated SRC test with a thermomechanical physical simulator. The stress and temperature range studied represents weld-induced residual stress at 150–600 MPa and post-weld heat treatment temperatures between 800 and 1050 °C. For all temperature conditions, the cross-welded samples failed at a lower critical stress threshold than the simulated HAZ. A finite element model of a 50.8-mm-thick single-V groove weld was used to generate the residual stress maps induced by a 40-pass welding procedure, which in combination with the experimental threshold stress map predicted potential SRC failure locations. Postmortem microstructural evaluations were performed to identify contributing characteristics to SRC. It was found that HAZ samples exhibited a combination of creep void development, secondary cracks with intergranular fracture near grain boundary carbides, and eutectic phases. FZ samples showed brittle fracture with cracks propagating along straight, non-tortuous interdendritic grain boundaries.

42 ENGINEERING↗
DOE OSTI2021

Probing the properties and mechanisms of failure waves in soda-lime glass

Soda-lime glass (SLG) and other silica glasses exhibit the failure wave phenomenon under shock compression. The mechanism responsible for this peculiar behavior of glasses is still unresolved. In this study, a series of plate impact experiments was performed at three different impact stresses of 6.4, 8.3, and 10.8 GPa to better understand the mechanisms underlying the failure wave phenomenon. Specifically, spall experiments were conducted to probe the speed and existence of failure waves at different stresses in SLG. A layered glass target was used to probe the possibility of a “renucleation” of the wave at the SLG–SLG interface. When it existed, the failure wave was inferred to propagate at a speed of 1.3 km/s. However, it was observed that the failure wave phenomenon ceases to exist for impact stresses higher than 10 GPa. In experiments with a 6.4 GPa impact stress, the peak free surface velocity was significantly less than what is predicted by stress-Hugoniot calculations. This velocity deficit and other important features of the measured free surface velocity profiles were simulated using finite element analysis by incorporating an abrupt densification of SLG at a critical stress in the equation of state. Furthermore, this densification feature is similar to what would be expected of a phase transition. Although unable to unambiguously reveal the mechanism causing the failure wave phenomenon, the results of the present work clearly indicate that the failure wave causes a secondary compression and densification in SLG.

36 MATERIALS SCIENCE↗
NASA NTRS1939

The limit of stability of a curved plate strip under shear and axial stresses

For an infinitely long plate strip of constant curvature there is set up the buckling condition for combined shear and axial stresses. Assumptions are made of the vanishing of the moments acting on the longitudinal edges and of the vanishing of the tangential displacements u and the transverse stresses sigma(sub y) (longitudinal stiffeners nonresistant to bending in the circumferential direction). The buckling condition is evaluated for the case of pure shear and an approximate formula is derived for the critical stresses for large curvatures. In connection with the discussion of the methods and results there is defined the range of validity and the buckling condition set up.

Kromm, A↗
NASA NTRS1979

Effect of misalignment on mechanical behavior of metals in creep

Application of the endochronic theory of viscoplasticity to creep, creep recovery, and stress relaxation at the small strain and short time range produced the following results: (1) The governing constitutive equations for constant-strain-rate stress-strain behavior, creep, creep recovery, and stress relaxation were derived by imposing appropriate constraints on the general constitutive equation of the endochronic theory. (2) A set of material constants was found which correlate strain-hardening, creep, creep recovery, and stress relaxation. (3) The theory predicts with reasonable accuracy the creep and creep recovery behaviors at short time. (4) The initial strain history prior to the creep stage affects the subsequent creep significantly. (5) A critical stress was established for creep recovery. A computer program, written for the misalignment problem is reported.

Wu, H. C.↗
NASA NTRS2011

Fracture in Phenolic Impregnated Carbon Ablator

The thermal protection materials used for spacecraft heat shields are subjected to various thermal-mechanical loads during an atmospheric reentry which can threaten the structural integrity of the system. This paper discusses the development of a novel technique to understand the failure mechanisms inside the thermal protection material, Phenolic Impregnated Carbon Ablator (PICA). PICA has successfully flown on the Stardust spacecraft and was the TPS material chosen for the Mars Science Laboratory (MSL), that will fly in 2011. Although PICA has good thermal properties, structurally, it is a weak material. To thoroughly understand failure in PICA, experiments were performed using FiberForm(Registered TradeMark) (precursor of PICA), virgin and furnace-charred PICA. Several small samples were tested inside an electron microscope to investigate the failure mechanisms. Micrographs were obtained before and after the failure in order to study crack initiation and growth. Videos were obtained to capture failure mechanisms in real time. Stress-strain data was obtained simultaneously for all the samples with the help of a data acquisition system, integrated to the mechanical stages. It was found that cracks initiated and grew in the FiberForm when a critical stress limit was reached such that the carbon fibers separated from the binder. However, both for virgin and charred PICA, crack initiation and growth occurred in the matrix (phenolic) phase. Both virgin and charred PICA showed greater strength values compared to FiberForm coupons, confirming that the presence of the porous matrix helps in absorbing the fracture energy.

Agrawal, Parul↗
NASA NTRS1991

Thermal shock testing for assuring reliability of glass-sealed microelectronic packages

Tests were performed to determine if thermal shocking is destructive to glass-to-metal seal microelectronic packages and if thermal shock step stressing can compare package reliabilities. Thermal shocking was shown to be not destructive to highly reliable glass seals. Pin-pull tests used to compare the interfacial pin glass strengths showed no differences between thermal shocked and not-thermal shocked headers. A 'critical stress resistance temperature' was not exhibited by the 14 pin Dual In-line Package (DIP) headers evaluated. Headers manufactured in cryogenic nitrogen based and exothermically generated atmospheres showed differences in as-received leak rates, residual oxide depths and pin glass interfacial strengths; these were caused by the different manufacturing methods, in particular, by the chemically etched pins used by one manufacturer. Both header types passed thermal shock tests to temperature differentials of 646 C. The sensitivity of helium leak rate measurements was improved up to 70 percent by baking headers for two hours at 200 C after thermal shocking.

Thomas, Walter B., III↗