Search NASA⌕ Search

SEARCH · Search NASA

Results for “CYCLIC LOAD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Experimental Methods for the Performance Test of Environment-Assisted Cracking (EAC) in Nuclear Industry and Examples through NSUF

Environmentally assisted cracking (EAC) is a critical failure mode in nuclear reactor environments, where materials are exposed to high temperatures, radiation, and corrosive media. Specific EAC studies in nuclear environments include stress corrosion cracking in primary water chemistry, irradiation-assisted stress corrosion cracking (IASCC) under neutron exposure, and hydrogen induced cracking (HIC) in reactor pressure vessels. The experimental methodologies of EAC include slow strain rate testing (SSRT), constant load, and cyclic loading techniques, conducted in autoclaves designed to simulate the reactor’s operational environments. This paper highlights several experimental case studies, especially on IASCC, conducted within the Nuclear Science User Facilities (NSUF).

36 - MATERIALS SCIENCE↗
NASA NTRS1975

Crack growth in ASME SA-105 grade 2 steel in hydrogen at ambient temperature

Cyclic-load crack growth measurements were performed on ASME SA-105 Grade 2 steel specimens exposed to 10,000- and 15,000-psi hydrogen and to 5000-psi helium, all at ambient temperatures. The cyclic-load crack growth rate was found to be faster in high-pressure hydrogen than in helium. Cyclic-load crack growth rates in this steel were not reduced by preloading in air to a stress intensity of 1.5 times the cyclic K sub max in hydrogen. There are indications that holding under load in hydrogen, and loading and unloading in helium retards hydrogen-accelerated cyclic-load crack growth. Cyclic frequency and R (ratio of K sub min/k sub max) were important variables determining crack growth rate. The crack growth rate increased as a logarithm of the cycle duration and decreased with increasing R.

Walter, R. J.↗
NASA NTRS1982

The role of peel stresses in cyclic debonding

When an adhesively bonded joint is undergoing cyclic loading, one of the possible damage modes that occurs is called cyclic debonding - progressive separation of the adherends by failure of the adhesive bond under cyclic loading. In most practical structures, both peel and shear stresses exist in the adhesive bonding during cyclic loading. The results of an experimental and analytical study to determine the role of peel stresses on cyclic debonding in a mixed mode specimen are presented. Experimentally, this was done by controlling the forces that create the peel stresses by applying a clamping force to oppose the peel stresses. Cracked lap shear joints were chosen for this study. A finite element analysis was developed to assess the effect of the clamping force on the strain energy release rates due to shear and peel stresses. The results imply that the peel stress is the principal stress causing cyclic debonding.

Everett, R. A., Jr.↗
NASA NTRS2001

Quantifying Residual Stresses by Means of Thermoelastic Stress Analysis

This study focused on the application of the Thermoelastic Stress Analysis (TSA) technique as a tool for assessing the residual stress state of structures. TSA is based on the fact that materials experience small temperature changes when compressed or expanded. When a structure is cyclically loaded, a surface temperature profile results which correlates to the surface stresses. The cyclic surface temperature is measured with an infrared camera. Traditionally, the amplitude of a TSA signal was theoretically defined to be linearly dependent on the cyclic stress amplitude. Recent studies have established that the temperature response is also dependent on the cyclic mean stress (i.e., the static stress state of the structure). In a previous study by the authors, it was shown that mean stresses significantly influenced the TSA results for titanium- and nickel-based alloys. This study continued the effort of accurate direct measurements of the mean stress effect by implementing various experimental modifications. In addition, a more in-depth analysis was conducted which involved analyzing the second harmonic of the temperature response. By obtaining the amplitudes of the first and second harmonics, the stress amplitude and the mean stress at a given point on a structure subjected to a cyclic load can be simultaneously obtained. The experimental results showed good agreement with the theoretical predictions for both the first and second harmonics of the temperature response. As a result, confidence was achieved concerning the ability to simultaneously obtain values for the static stress state as well as the cyclic stress amplitude of structures subjected to cyclic loads using the TSA technique. With continued research, it is now feasible to establish a protocol that would enable the monitoring of residual stresses in structures utilizing TSA.

Gyekenyesi, Andrew L.↗
NASA NTRS1980

Fatigue properties of shuttle thermal protection system

Static and cyclic load tests were conducted to determine the static and fatigue strength of the RIS tile/SIP thermal protection system used on the orbiter of the space shuttle. The material systems investigated include the densified and undensified LI-900 tile system on the .40 cm thick SIP and the densified and undensified LI-2200 tile system on the .23 cm (.090 inch) thick SIP. The tests were conducted at room temperature with a fully reversed uniform cyclic loading at 1 Hertz. Cyclic loading causes a relatively large reduction in the stress level that each of the SIP/tile systems can withstand for a small number of cycles. For example, the average static strength of the .40 cm thick SIP/LI-900 tile system is reduced from 86 kPa to 62 kPa for a thousand cycles. Although the .23 cm thick SIP/LI-2200 tile system has a higher static strength, similar reductions in the fatigue strength are noted. Densifying the faying surface of the RSI tile changes the failure mode from the SIP/tile interface to the parent RSI or the SIP and thus greatly increases the static strength of the system. Fatigue failure for the densified tile system, however, occurs due to complete separation or excessive elongation of the SIP and the fatigue strength is only slightly greater than that for the undensified tile system.

Sawyer, J. W.↗
NASA NTRS2014

Evaluating Daily Load Stimulus Formulas in Relating Bone Response to Exercise

Six formulas representing what is commonly referred to as "daily load stimulus" are identified, compared and tested in their ability to relate skeletal mechanical loading to bone maintenance and osteogenic response. Particular emphasis is placed on exercise- induced skeletal loading and whether or not the formulas can adequately capture the known experimental observations of saturation of continuous cyclic loading, rest insertion between repetitions (cycles), recovery of osteogenic potential following saturation, and multiple shorter bouts versus a single long bout of exercise. To evaluate the ability of the formulas to capture these characteristics, a set of exercise scenarios with type of exercise bout, specific duration, number of repetitions, and rest insertion between repetitions is defined. The daily load values obtained from the formulas for the loading conditions of the set of scenarios is illustrated. Not all of the formulas form estimates of daily load in units of stress or in terms of strain at a skeletal site due to the loading force from a specific exercise prescription. The comparative results show that none of the formulas are able to capture all of the experimentally observed characteristics of cyclic loading. However, the enhanced formula presented by Genc et al. does capture several characteristics of cyclic loading that the others do not, namely recovery of osteogenic potential and saturation. This could be a basis for further development of mathematical formulas that more adequately approximates the amount of daily stress at a skeletal site that contributes to bone adaptation.

Pennline, James A.↗
NASA NTRS2003

Analysis of Plasma-Sprayed Thermal Barrier Coatings With Homogeneous and Heterogeneous Bond Coats Under Spatially Uniform Cyclic Thermal Loading

This report summarizes the results of a numerical investigation into the spallation mechanism in plasma-sprayed thermal barrier coatings observed under spatially-uniform cyclic thermal loading. The analysis focuses on the evolution of local stress and inelastic strain fields in the vicinity of the rough top/bond coat interface during thermal cycling, and how these fields are influenced by the presence of an oxide film and spatially uniform and graded distributions of alumina particles in the metallic bond coat aimed at reducing the top/bond coat thermal expansion mismatch. The impact of these factors on the potential growth of a local horizontal delamination at the rough interface's crest is included. The analysis is conducted using the Higher-Order Theory for Functionally Graded Materials with creep/relaxation constituent modeling capabilities. For two-phase bond coat microstructures, both the actual and homogenized properties are employed in the analysis. The results reveal the important contributions of both the normal and shear stress components to the delamination growth potential in the presence of an oxide film, and suggest mixed-mode crack propagation. The use of bond coats with uniform or graded microstructures is shown to increase the potential for delamination growth by increasing the magnitude of the crack-tip shear stress component.

Arnold, Steven M.↗
NASA NTRS1978

Origin of moisture effects on crack propagation in composites

A study has been made of the origin of unexpected moisture effects on crack extension in fiberglass laminates. Water immersion has been found to greatly reduce the rate of crack growth under constant loading, while increasing the rate under cyclic loading, the latter effect being the expected one. Observations were made of the extension of the stable damage zone at the tip of precut notches in wet and dry environments. The damage zone size is postulated as a critical element in the relaxation of high stress concentrations in composites, such as those at notch or crack tips. Under constant load, moisture is shown to greatly expand the interply delamination region in the damage zone, thus reducing the local fiber stresses and increasing crack resistance. Under cyclic loading moisture has little effect on the delamination region, which is large even for dry environments, and the only effect is weakening of the material and acceleration of cracks. Severe hygrothermal conditions can so weaken the material that the crack resistance is reduced under constant loading as well.

Mandell, J. F.↗
NASA NTRS1979

Preliminary analysis of performance and loads data from the 2-megawatt mod-1 wind turbine generator

Preliminary test data on output power versus wind speed, rotor blade loads, system dynamic behavior, and start-stop characteristics on the Mod-1 wind turbine generator are presented. These data were analyzed statistically and are compared with design predictions of system performance and loads. To date, the Mod-1 wind turbine generator has produced up to 1.5 MW of power, with a measured power versus wind speed curve which agrees closely with design. Blade loads were measured at wind speeds up to 14 m/s and also during rapid shutdowns. Peak transient loads during the most severe shutdowns are less than the design limit loads. On the inboard blade sections, fatigue loads are approximately equal to the design cyclic loads. On the outboard blade sections, however, measured cyclic loads are significantly larger than design values, but they do not appear to exceed fatigue allowable loads as yet.

Spera, D. A.↗
NASA NTRS1972

Static and dynamic fatigue behavior of glass filament-wound pressure vessels at ambient and cryogenic temperatures.

Investigation of the pressure load carrying capacity and fatigue strength of filament-wound glass-reinforced plastic pressure vessels subjected to static and cyclic loading at ambient and cryogenic (liquid nitrogen) temperature environments. The results indicate that the static fatigue problem is not critical at cryogenic temperatures. Under static loading at liquid nitrogen temperature, a reinforced plastic cylinder sustained pressurization for 88 days without failure at about 90% of the single cycle burst strength. At ambient temperature, the static life at 90% of the burst strength was about 7 min. Under cyclic loading in liquid nitrogen, no failure resulted after 1509 cycles at 55% of the single cycle burst strength. Under the same cyclic loading at ambient temperature, the test results would predict failure in the reinforced plastic. The results of similar tests upon adhesively bonded polyimide aluminum-foil lined cylinders are also reviewed.-

Hanson, M. P.↗
NASA NTRS1990

Survivability characteristics of composite compression structure

Test and evaluation was performed to determine the compression residual capability of graphite reinforced composite panels following perforation by high-velocity fragments representative of combat threats. Assessments were made of the size of the ballistic damage, the effect of applied compression load at impact, damage growth during cyclic loading and residual static strength. Several fiber/matrix systems were investigated including high-strain fibers, tough epoxies, and APC-2 thermoplastic. Additionally, several laminate configurations were evaluated including hard and soft laminates and the incorporation of buffer strips and stitching for improved damage resistance of tolerance. Both panels (12 x 20-inches) and full scale box-beam components were tested to assure scalability of results. The evaluation generally showed small differences in the responses of the material systems tested. The soft laminate configurations with concentrated reinforcement exhibited the highest residual strength. Ballistic damage did not grow or increase in severity as a result of cyclic loading, and the effects of applied load at impact were not significant under the conditions tested.

Avery, John G.↗
NASA NTRS1986

Damage-induced property changes in composites subjected to cyclic thermal loading

Damage in the form of transverse cracks resulting from thermal loading is studied as it relates to the dimensional stability of flat laminates and stiffness changes in cylindrical tubes. Graphite-epoxy specimens were subjected to cyclic thermal loading in the temperature range -250 to + 250 F. It is shown that transverse cracking is the dominant damage mechanism in both types of structural elements. Fiber splitting is also quite common at the low test temperatures. Experimental results indicate that damage significantly reduces the inplane coefficients of thermal expansion of flat laminates and the torsional stiffness of the tubes. Theoretical predictions for coefficients of thermal expansion as a function of crack spacing in flat laminates followed the same trend as experimental results.

Herakovich, Carl T.↗
NASA NTRS1979

An elastic-plastic analysis of fatigue crack closure in modes I and II

In this paper, an efficient elastic-plastic finite element procedure to analyze crack-closure and, its effects on fatigue crack growth under general spectrum loading, is presented. A hybrid-displacement finite element procedure is used to properly treat the stress and strain singularities near the crack-tip; and crack-growth under cyclic loading is simulated by the translation of certain 'core' elements, near the crack-tip, in which proper stress and strain singularities were embedded. Both pure mode I and mode II types of cyclic loading are considered. In the mode I case, four types of cyclic loading, viz., constant amplitude block loading, high-to-low block loading, low-to-high block, and a single overload in an otherwise constant amplitude block loading are considered; whereas in mode II, only a constant amplitude block loading is considered. Detailed results are presented for the crack-closure and opening-stresses, crack-surface deformation profiles, etc., in each case. Certain observations, based on the present numerical results, concerning various factors that cause crack growth acceleration or retardation under general spectrum loading, are presented and discussed.

Nakagaki, M.↗
NASA NTRS1976

A finite-element analysis of fatigue crack closure

The paper is concerned with the application of a two-dimensional, nonlinear, finite-element analysis using an incremental theory of plasticity to predict crack-closure and crack-opening stresses during the crack-growth process under cyclic loading. A two-dimensional finite-element computer program is developed, which accounts for both elastic-plastic material behavior and changing boundary conditions associated with crack extension and intermittent contact of the crack surfaces under cyclic loading. An efficient technique to account for changing boundary conditions under cyclic loading is also incorporated into the nonlinear analysis program. This program is used to study crack extension and crack closure behavior in a center-cracked panel under constant-amplitude and two-level block loading. The calculated crack-opening stresses are found to be quantitatively consistent with experimental measurements.

Newman, J. C., Jr.↗
NASA NTRS1995

Thermomechanical Fatigue Behavior of Three Cfcc's

The thermomechanical fatigue (TMF) behavior of three continuous-fiber ceramic composites (CFCC's) was examined. The three matrices consisted of two different glass-ceramics and silicon carbide, respectively. The matrices of some of the specimens with the silicon carbide matrix were enhanced to improve oxidation resistance. All three were reinforced with Nicalon fibers with various fiber architectures. The thermoelastic properties of the matrix relative to the fibers, the elastic moduli and coefficients of thermal expansion (CTE), were different in each composite, providing a comparison of the effects of these critical properties. The specimens were tested under in-phase (IP) and out-of-phase (OP) cyclic loadings with respect to thermal cycling between 600 C and 1100 C. One of the glass-ceramic composites had greatly increased TMF lives compared to the other glass-ceramic matrix composites. This was probably caused by the reversal of the CTE mismatch between the fibers and the matrices and caused by the different oxidation resistances of the composites. For the same TMF lives a cross-ply reinforced composite had a maximum cyclic stress half as great, as that of unidirectionally reinforced composite. This indicated that the (0 deg) ply fibers had a strong influence of TMF life. Both the glass ceramic matrix composites had shallow-slope stress-life plots that indicated sensitivity to damage and therefore low damage tolerance. The composites with an unenhanced silicon carbide matrix experienced the shortest TMF lives of all the CFCC's tested. However, the enhanced composite had the longest. Also, the enhanced composite demonstrated the best damage tolerance as evidenced by a stress-life curve that curves sharply upward to the left. In all the composites, out-of-phase cyclic loading was worse than in-phase cyclic loadings despite the CTE mismatch between fiber and matrix. A damage investigation and a preliminary analysis of the stresses in the fibers and matrices taking into account their respective thermoelastic properties provided insight into the relative behavior of the glass-ceramic matrix composites under IP and OP TMF.

Worthem, Dennis W.↗
NASA NTRS1985

Interaction of mixed mode loading on cyclic debonding in adhesively bonded composite joints

A combined experimental and analytical investigation of an adhesively-bonded composite joint was conducted to characterize the fracture mode dependence of cyclic debonding. The system studied consisted of graphite/epoxy adherends bonded with EC 3445 adhesive. Several types of specimens are tested which provide the cyclic debond growth rate measurements under various load conditions: mode 1, mixed mode 1 to 2, and mostly mode 2. This study shows that the total strain-energy-release rate is the governing factor for cyclic debonding.

Mall, S.↗
NASA NTRS1985

Interaction of mixed mode loading on cyclic debonding in adhesively bonded composite joints

A combined experimental and analytical investigation of an adhesively-bonded composite joint was conducted to characterize the fracture mode dependence of cyclic debonding. The system studied consisted of graphite/epoxy adherends bonded with EC 3445 adhesive. Several types of specimens are tested which provide the cyclic debond growth rate measurements under various load conditions: mode 1, mixed mode 1 to 2, and mostly mode 2. This study shows that the total strain-energy-release rate is the governing factor for cyclic debonding.

Mall, S.↗