Search NASA⌕ Search

SEARCH · Search NASA

Results for “Catalyst screening”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Programmable catalysis by support polarization: elucidating and breaking scaling relations

The Sabatier principle and the scaling relations have been widely used to search for and screen new catalysts in the field of catalysis. However, these powerful tools can also serve as limitations of catalyst control and breakthrough. To overcome this challenge, this work proposes an efficient method of studying catalyst control by support polarization from first-principles. The results demonstrate that the properties of catalysts are determined by support polarization, irrespective of the magnitude of spontaneous polarization of support. The approach enables elucidating the scaling relations between binding energies at various polarization values of support. Moreover, we observe the breakdown of scaling relations for the surface controlled by support polarization. By studying the surface electronic structure and decomposing the induced charge into contributions from different atoms and orbitals, we identify the inherent structural property of the interface that leads to the breaking of the scaling relations. Specifically, the displacements of the underlying oxide support impose its symmetry on the catalyst, causing the scaling relations between different adsorption sites to break.

Chemical engineering↗

Screening Bifunctional Pt Based NSTF Catalysts for Durability with the Rotating Disk Electrode: The Effect of Ir and Ru

Various amounts of Ir (<20 μg cm -2 ) and Ru (up to 12 μg cm -2 ) on a consistent base Pt loading of 85 μg cm -2 , were sputter deposited on a nanostructured thin film catalyst support to mimic a hydrogen fuel cell's cathode catalyst. The nanostructured support was grown on glassy carbon disks designed for a rotating disk electrode, which was used to simulate what happens to a fuel cell cathode during repeated start-up, operation, and shut-down. The testing protocol subjected the catalyst to a minimum potential of 0.65 V RHE and a maximum between 1.53 and 1.8 V RHE . The upper potential was achieved with a galvanostatic hold which is an alternative way to simulate potential transients on the cathode caused by start-up and shut-down. Increasing Ir loading improved the durability of both oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) activity. When combined with Ir, Ru provided no benefit to OER durability except at an Ir loading of 10 μg cm -2 . Ru addition (no Ir present) improved the ORR durability compared to pure Pt. ORR durability was not influenced by Ru addition to Ir-containing samples. In general, ORR durability showed no dependence on Ru loading for all the Ru containing samples and ORR activity was decreased by OER catalyst addition, though more so for Ir than Ru.

25 ENERGY STORAGE↗

Laminar Entrained Flow Reactor (Fact Sheet)

The Laminar Entrained Flow Reactor (LEFR) is a modular, lab scale, single-user reactor for the study of catalytic fast pyrolysis (CFP). This system can be employed to study a variety of reactor conditions for both in situ and ex situ CFP.

09 BIOMASS FUELS↗

Final Report: DE- FC36-05GO15063, Fundamental Studies of Advanced High-Capacity, Reversible Metal Hydrides

The project was component of the US DOE, Metal Hydride Center of Excellence (MHCoE). The Sandia National Laboratory led center was established to conduct highly collaborative and multi-disciplinary applied R&D to develop new reversible hydrogen storage materials that meet or exceed DOE/FreedomCAR 2010 and 2015 system targets for hydrogen storage materials. Our approach entailed a wide variety of activities ranging from synthesis, characterization, and evaluation of new candidate hydrogen storage materials; screening of catalysts for high capacity materials requiring kinetics enhancement; development of low temperature methods for nano-confinement of hydrides and determining its effects on the kinetics and thermodynamics of hydrides; and development of novel processes for the direct re-hydrogenation of materials. These efforts have resulted in several advancements the development of hydrogen storage materials. We have greatly extended the fundamental knowledge about the highly promising hydrogen storage carrier, alane (AlH 3 ), by carrying out the first crystal structure determinations and the first determination of the heats of dehydrogenation of β–AlH 3 and γ-AlD 3 . A low-temperature homogenous organometallic approach to incorporation of Al and Mg based hydrides into carbon aerogels has been developed that that allows high loadings without degradation of the nano-porous scaffold. Nano-confinement was found to significantly improve the dehydrogenation kinetics but not effect the enthalpy of dehydrogenation. We conceived, characterized, and synthesized a novel class of potential hydrogen storage materials, bimetallic borohydrides. These novel compounds were found to have many favorable properties including release of significant amounts of hydrogen at moderate temperatures (75-190 º C). However, in situ IR studies in tandem with thermal gravimetric analysis have shown that about 0.5 equivalents of diborane are released during the dehydrogenation making re-hydrogenation effectively impossible and precluding these compounds from further consideration as hydrogen storage materials. The hydrogen cycling of >11 wt % between MgB 2 to Mg(BH 4 ) 2 was achieved but required very forcing conditions. Under moderate conditions (dehydrogenation 200°C; re-hydrogenation 250°C, 120 atm H 2 ), Mg(BH 4 ) 2 undergoes reversible dehydrogenation to Mg(B 3 H 8 ) 2 . Although the 2.5 wt% cycling capacity does not meet current on-board storage targets, this result provides first example of direct hydrogen cycling of a borohydride under moderate conditions and demonstrates the plausibility of finding mild, PEM fuel cell relevant conditions for the high capacity, reversible dehydrogenation of borohydrides. A method was developed for the room temperature, direct hydrogenation of Ti-doped LiH/Al in liquefied dimethyl ether under 100 atm of H 2 . The process has been optimized such that Ti-doped LiAlH 4 is obtained in >95% yield. The WTT energy efficiency our direct synthesis process has been estimated to approach the 60% U.S. DOE target. Thus our simplification of the hydrogenation half-cycle may provide the key to harnessing the long-recognized potential of this lightweight, high capacity material as a practical hydrogen carrier. Finally, we have gained insight into the fundamental basis of the enhanced hydrogen cycling kinetics of Ti-doped NaAlH 4 through studies by solid state 1 H NMR, anelastic spectroscopy; muon spin rotation; and positron annihilation.

08 HYDROGEN↗

Perfluroether triazine elastomers

In order to obtain high performance elastomers with the high thermal stability and chemical inertness of perfluoroalkylene triazine and a low glass transition temperature, perfluoroether triazine elastomers were synthesized. The procedure for elastomer synthesis is described as well as general experimental methods. Results are presented and discussed. The screening of catalysts for the dehydration of perfluoroether diamide is also considered.

Korus, R. A.↗

Apparatus for Screening Multiple Oxygen-Reduction Catalysts

An apparatus that includes an array of multiple electrodes has been invented as a means of simultaneously testing multiple materials for their utility as oxygen-reduction catalysts in fuel cells. The apparatus ensures comparability of test results by exposing all the catalyst-material specimens to the same electrolytic test solution at the same potential. Heretofore, it has been possible to test only one specimen at a time, using a precise rotating disk electrode that provides a controlled flux of solution to the surface of the specimen.

Whitacre, Jay↗

Electrochemical polymer pen lithography

Disclosed herein is a massively parallel patterning tool for the deposition of single metals or metal alloys with size and composition control. Methods of the disclosure use a hydrogel array of pyramidal pen tips as a medium for localized electrodeposition, in conjunction with a scanning probe lithography platform and a three-electrode cell. This versatile technique can be used for high-throughput 3D printing, biomolecule patterning, or screening of catalyst nanoparticles or thin films.

Mirkin, Chad A.↗

Adsorbate-induced adatom formation on Au-Cu bimetallic alloys and its possible consequences for CO 2 electroreduction

The adsorbate-induced formation of sub-nanometer clusters on transition-metal single crystals observed in previous high-pressure microscopic studies hinted at the in-situ formation of unique active sites even on large nanoparticle catalysts. We propose that the adatom formation energy can be used as an energetic descriptor for the initial step toward the adsorbate-induced metal-cluster formation process. This descriptor can be efficiently computed using density functional theory (DFT) calculations and applied for screening and identification of metal catalysts where this phenomenon may play an important role in generating active sites in-situ. As a proof of concept, here, we construct an adatom formation energy database for three Au x Cu y alloys (x:y = 3:1, 1:1, or 1:3) and eighteen adsorbates (H, C, N, O, F, S, Cl, Br, I, CH x , NH x (x = 1 – 3), CO, NO, and OH) commonly involved in catalytic reactions. The energetics of adatom formation were examined in all cases where the (111) terrace, (211) step-edge, and (874) kink were the sources of the adatom. We demonstrate that the presence of an adsorbate could alter not only the energetics for adatom formation but also the elemental nature of the preferred adatom being formed. Using our database, we identified promising systems which favor adsorbate-induced adatom formation under near-ambient conditions. Specifically, CO-induced adatom formation on all three Au-Cu alloy surfaces could occur under CO 2 electroreduction (CO 2 RR) conditions. This phenomenon offers a qualitative explanation for the experimentally observed CO 2 RR activity on Au-Cu alloy catalysts. As a result, our methodology offers an easily expandable and efficient approach for large-scale catalyst screening with regards to adatom/cluster formation under reaction conditions and provides insight into the possible nature of active sites on alloy catalysts from a novel perspective.

Active site↗

Optimizing PtFe intermetallics for oxygen reduction reaction: from DFT screening to in situ XAFS characterization

Rational designing of catalysts to promote the sluggish kinetics of the cathode oxygen reduction reaction in proton exchange membrane fuel cells is still challenging, yet of crucial importance to its commercial application. Here, on the basis of theoretical DFT calculations which suggest that order structured fct-phased PtFe (O-PtFe) with an atomic Pt shell exhibits superior electrocatalytic performance towards the ORR, the desired structure was prepared by using a scalable impregnation–reduction method. The as-prepared O-PtFe delivered enhanced activity (0.68 A mg -1 Pt ) and stability (73% activity retention after 10 000 potential cycles) compared with the corresponding disordered PtFe alloy (D-PtFe) and Pt. To confirm the excellent durability, in situ X-ray absorption fine structure spectroscopy was conducted to probe the local and electronic structure changes of O-PtFe during 10 000 cycle accelerated durability testing. In conclusion, we hope that this facile synthesis method and the in situ XAFS experiment could be readily adapted to other catalyst systems, facilitating the screening of highly efficient ORR catalysts for fuel cell application.

36 MATERIALS SCIENCE↗

Optimization of metal-supported solid oxide electrolysis cells with infiltrated catalysts

We report metal-supported solid oxide electrolysis cells (MS-SOECs) are being developed for steam-to-hydrogen electrolysis, especially for utilization of dynamic or intermittent electrical power from renewable sources. Various aspects of the electrocatalyst processing and composition, and metal support structure were explored. Catalyst materials, infiltration temperature and infiltration cycles were optimized for high performance and durability. Numerous catalyst materials were screened for both oxygen and steam electrodes. The oxygen catalyst had moderate impact on both initial cell performance and durability. Reducing Ni content in the steam electrode had little effect on durability, but reduced initial performance. Ex-situ XRD analysis and cell assessment of catalyst infiltration temperature revealed that the optimal range is 750–850 °C. The best cell performance and durability was achieved with LSCF-SDC oxygen electrocatalyst and SDC-Ni (60:40 vol%) steam electrocatalyst infiltrated 11 times at 800 °C and operated at 700 °C. At low steam content, a significant mass transport limitation on the steam side results in limiting current behavior. Thinner and more porous metal supports were implemented, and found to improve steam mass transport at low steam content, relevant for SOECs operating under high H 2 recycle rate or high steam utilization.

08 HYDROGEN↗

Scanning Electrochemical Flow Cell with Online Mass Spectroscopy for Accelerated Screening of Carbon Dioxide Reduction Electrocatalysts

Electrochemical conversion of carbon dioxide into valuable chemicals or fuels is an increasingly important strategy for achieving carbon neutral technologies. The lack of a sufficiently active and selective electrocatalyst, particularly for synthesizing highly reduced products, motivates accelerated screening to evaluate new catalyst spaces. Traditional techniques, which couple electrocatalyst operation with analytical techniques to measure product distributions, enable screening throughput at 1–10 catalysts per day. In this paper, a combinatorial screening instrument is designed for MS detection of hydrogen, methane, and ethylene in quasi-real-time during catalyst operation experiments in an electrochemical flow cell. Coupled with experiment modeling, product detection during cyclic voltammetry (CV) enables modeling of the voltage-dependent partial current density for each detected product. Here, we demonstrate the technique by using the well-established thin film Cu catalysts and by screening a Pd–Zn composition library in carbonate-buffered aqueous electrolyte. The rapid product distribution characterization over a large range of overpotential makes the instrument uniquely suited for accelerating screening of electrocatalysts for the carbon dioxide reduction reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Writing the Programs of Programmable Catalysis

It has long been known that non-steady state and periodic catalytic reactor operation in terms of temperature, pressure, and composition can lead to higher overall productivity and/or product selectivity than the best steady operation. Recently, the emergence of catalysts whose intrinsic properties can be made to oscillate with time, introduces advanced forcing capabilities that can be “programmed” into the catalysts to broaden the scope and applicability of periodic operation to surface chemistry. In this work, an algorithmic approach is implemented to significantly accelerate the discovery and optimization of periodic steady states of catalytic reactors. Decomposition of complex dynamics into fundamental mechanistic fast–slow steps is seen to improve conceptual understanding of the relationship between binding energy oscillation protocols and overall catalytic rates. Finding structured forcing protocols, optimally tailored to the multiple time scales of a given individual mechanism, requires an efficient search of high-dimensional parameter spaces. Here, this is enabled here through active learning (Bayesian optimization, enhanced by our proposed Bayesian continuation). Implementation of these methods is shown to accelerate the evaluation of catalyst programs by up to several orders of magnitude. Faster screening of programmable catalysts to discover periodic steady states enables the optimization of catalytic operating protocols and thus opens the possibility for catalyst engineering based on optimal forcing programs to control rate and product selectivity, even for complex multistep catalytic mechanisms.

catalysis↗

Optimization of Rhodium-Based Catalysts for Mixed Alcohol Synthesis -- 2009 Progress Report

Pacific Northwest National Laboratory (PNNL) has been conducting research for the United States Department of Energy, Energy Efficiency Renewable Energy, Biomass Program to investigate the feasibility of producing mixed alcohols from biomass-derived synthesis gas (syngas). This research has involved the screening of potential catalysts, and optimization of the more promising ones, using laboratory scale reactors. During 2009, the main goal of the testing program focused on optimizing selected supported catalysts containing rhodium (Rh) and manganese (Mn). Optimization involved examining different total concentrations and atomic ratios of Rh and Mn as well as that of the more promising promoters (Ir and Li) identified in the earlier screening studies. Evaluation of catalyst performance focused on attaining improvements with respect to the space-time-yield and converted carbon selectivity to C2+ oxygenates, with additional consideration given to the fraction of the oxygenates that were C2+ alcohols.

09 BIOMASS FUELS↗

Conversion of CO 2 into Commercial Materials Using Carbon Feedstocks

In this project, our research focused on developing reaction chemistry that would support using carbon as a reductant for CO 2 utilization that would permit CO 2 consumption on a scale that would match or exceed anthropomorphic CO 2 generation for energy production from fossil fuels. Armed with the knowledge that reactions attempting to produce compounds with an energy content greater than CO 2 would be thermodynamically challenged and/or require significant amounts of energy, we developed a potential process that utilized a solid carbon source and recycled the carbon to effectively provide infinite time for the carbon to react. During testing of different carbon sources, we found a wide range of reaction rates. Biomass-derived samples had the most reactivity and coals and petcoke had the lowest. Because we had anticipated this challenge, we recognized that a catalyst would be necessary to improve reaction rates and conversion. From the data analysis of carbon samples, we recognized that alkali metals improved the reaction rate. Through parametric testing of catalyst formulations we were able to increase the reaction rate with petcoke by a factor of >70. Our efforts to identify the reaction mechanism to assist in improving the catalyst formulation demonstrated that the catalyst was catalyzing the extraction of oxygen from CO 2 and using this extracted oxygen to oxidize carbon. This was a significant discovery in that if we could modify the catalyst formulation to permit controlled the oxidation, we would have a very power selective oxidation process. With selective oxidation, CO 2 utilization could be effective used as one of the process steps in making many of the large volume commodity chemicals that support our modern lifestyles. The key challenges for incorporating these functionalities into the catalyst formulation were to make the oxidation selective and lower the temperature required for catalytic activity. We identified four catalyst families that had the potential to meet these challenges. Initial screening of the catalyst families did show that the reduction/oxidation activity did occur at lower temperatures and that these catalysts were able to cause carbon chain growth as well as C—C cleavage. A preliminary techno-economic feasibility of using petcoke/catalyst to produce a CO-rich syngas product was completed and showed significant economic promise. Testing of the different catalyst families demonstrated that Catalyst A was able to stably produce 5 sccm of ethylene/gram of catalyst at 900°C for one hour. For dry methane reforming, our Catalyst 4 was able to achieve production rates of > 10 sccm of CO and > 3 sccm of H2 per gram of catalyst at 600°C and 350 psig. Based on these developments, the potential for CO 2 utilization in the production of large volume commodity chemicals is very promising.

10 SYNTHETIC FUELS↗

Design and Validation of a High-Throughput Reductive Catalytic Fractionation Method

Reductive catalytic fractionation (RCF) is a promising method to extract and depolymerize lignin from biomass, and bench-scale studies have enabled considerable progress in the past decade. RCF experiments are typically conducted in pressurized batch reactors with volumes ranging between 50 and 1000 mL, limiting the throughput of these experiments to one to six reactions per day for an individual researcher. Here, we report a high-throughput RCF (HTP-RCF) method in which batch RCF reactions are conducted in 1 mL wells machined directly into Hastelloy reactor plates. The plate reactors can seal high pressures produced by organic solvents by vertically stacking multiple reactor plates, leading to a compact and modular system capable of performing 240 reactions per experiment. Using this setup, we screened solvent mixtures and catalyst loadings for hydrogen-free RCF using 50 mg poplar and 0.5 mL reaction solvent. The system of 1:1 isopropanol/methanol showed optimal monomer yields and selectivity to 4-propyl substituted monomers, and validation reactions using 75 mL batch reactors produced identical monomer yields. To accommodate the low material loadings, we then developed a workup procedure for parallel filtration, washing, and drying of samples and a 1H nuclear magnetic resonance spectroscopy method to measure the RCF oil yield without performing liquid-liquid extraction. As a demonstration of this experimental pipeline, 50 unique switchgrass samples were screened in RCF reactions in the HTP-RCF system, revealing a wide range of monomer yields (21-36%), S/G ratios (0.41-0.93), and oil yields (40-75%). These results were successfully validated by repeating RCF reactions in 75 mL batch reactors for a subset of samples. We anticipate that this approach can be used to rapidly screen substrates, catalysts, and reaction conditions in high-pressure batch reactions with higher throughput than standard batch reactors.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗

Final Technical Report on Development of an Economic and Efficient Biodiesel production Process (NC)

The Biofuels Team at The University of North Carolina at Pembroke and North Carolina A&T State University carried out a joint research project aimed at developing an efficient process to produce biodiesel. In this project, the team developed and tested various types of homogeneous and heterogeneous catalysts which could replace the conventionally used soluble potassium hydroxide catalyst which, traditionally, must be separated and disposed of at the end of the process. As a result of this screening, the homogeneous catalyst choline hydroxide was identified as a potential replacement for the traditional catalyst used in this process, potassium hydroxide, due to its decreased corrosiveness and toxicity. A large number of heterogeneous catalysts were produced and tested in order to determine the scaffold, ion type and ion concentration which would produce optimum yield of biodiesel. The catalyst with 12% calcium on Zeolite β was identified as being highly effective and optimal reaction conditions were identified. Furthermore, a packed bed reactor utilizing this type of catalyst was designed, constructed and tested in order to further optimize the process. An economic analysis of the viability of the project showed that the cost of an independent farmer to produce the fuelstock required to produce biodiesel exceeds the cost of petroleum diesel under current conditions and that therefore without incentives, farmers would not be able to benefit economically from producing their own fuel. An educational website on biodiesel production and analysis was produced and a laboratory experiment demonstrating the production of biodiesel was developed and implemented into the Organic Chemistry II laboratory curriculum at UNCP. Five workshops for local farmers and agricultural agents were held in order to inform the broader community about the various fuelstock available, their cultivation and the process and advantages of biodiesel use and production. This project fits both Universities’ goals in the Biofuels Research Initiative, since it uses an alternative fuelstock: namely canola. The outcomes of this project may eventually aid in reducing the state’s consumption of corn and soybean, which are important food crops. The project will also encourage regional farmers to grow alternative crops for biofuel production. The success of this project has contributed towards the development of Robeson County, an economically disadvantaged region. Additionally it should be noted that Robeson County serves a large Native American population. Therefore, training and engaging this minority group in the energy industry was an important accomplishment.

09 BIOMASS FUELS↗

Removal of ammonia from urine vapor by a dual-catalyst system

The feasibility of removing ammonia from urine vapor by a low-temperature dual-catalyst system has been demonstrated. The process is based on the catalytic oxidation of ammonia to a mixture of nitrogen, nitrous oxide, and water, followed by a catalytic decomposition of the nitrous oxide into its elements. Potential ammonia oxidation and nitrous oxide decomposition catalysts were first screened with artificial gas mixtures, then tested with the actual urine vapor produced by boiling untreated urine. A suitable dual-catalyst bed arrangement was found that achieved the removal of ammonia and also organic carbon, and recovered water of good quality from urine vapor.

Budininkas, P.↗